U(V) Stabilization via Aliovalent Incorporation of Ln(III) into Oxo-salt Framework.

Pentavalent uranium compounds are key components of uranium's redox chemistry and play important roles in environmental transport. Despite this, well-characterized U(V) compounds are scarce primarily because of their instability with respect to disproportionation to U(IV) and U(VI). In this work, we provide an alternate route to incorporation of U(V) into a crystalline lattice where different oxidation states of uranium can be stabilized through the incorporation of secondary cations with different sizes and charges. We show that iriginite-based crystalline layers allow for systematically replacing U(VI) with U(V) through aliovalent substitution of 2+ alkaline-earth or 3+ rare-earth cations as dopant ions under high-temperature conditions, specifically Ca(UVIO2)W4O14 and Ln(UVO2)W4O14 (Ln=Nd, Sm, Eu, Gd, Yb). Evidence for the existence of U(V) and U(VI) is supported by single-crystal X-ray diffraction, high energy resolution X-ray absorption near edge structure, X-ray photoelectron spectroscopy, and optical absorption spectroscopy. In contrast with other reported U(V) materials, the U(V) single crystals obtained using this route are relatively large (several centimeters) and easily reproducible, and thus provide a substantial improvement in the facile synthesis and stabilization of U(V).

The electrocatalytic activity for the hydrogen evolution reaction on alloys is determined by element-specific adsorption sites rather than d-band properties.

Trends of the electrocatalytic activities for the hydrogen evolution reaction (HER) across transition metals are typically explained by d-band properties such as center or upper edge positions in relation to Fermi levels. Here, the universality of this relation is questioned for alloys, exemplified for the AuPt system which is examined with electrocatalytic measurements and density functional theory (DFT) calculations. At small overpotentials, linear combinations of the pure-metals' Tafel kinetics normalized to the alloy compositions are found to precisely resemble the measured HER activities. DFT calculations show almost neighbor-independent adsorption energies on Au and Pt surface-sites, respectively, as the adsorbed hydrogen influences the electron density mostly locally at the adsorption site itself. In contrast, the density of states of the d-band describe the delocalized conduction electrons in the alloys, which are unable to portray the local electronic environments at adsorption sites and related bonding strengths. The adsorption energies at element-specific surface sites are related to overpotential-dependent reaction mechanisms in a multidimensional reinterpretation of the volcano plot for alloys, which bridges the found inconsistencies between activity and bonding strength descriptors of the common electrocatalytic theory for alloys.

How microstructures, oxide layers, and charge transfer reactions influence double layer capacitances. Part 1: impedance spectroscopy and cyclic voltammetry to estimate electrochemically active surface areas (ECSAs).

Varying the electrode potential rearranges the charges in the double layer (DL) of an electrochemical interface by a resistive-capacitive current response. The capacitances of such charge relocations are frequently used in the research community to estimate electrochemical active surface areas (ECSAs), yet the reliability of this methodology is insufficiently examined. Here, the relation of capacitances and ECSAs is critically assessed with electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) data on polished (Au, Ti, Ru, Pt, Ni, glassy carbon, graphite plate) and porous (carbon fleeces) electrodes. By investigating this variety of electrodes, the frequency-dependencies observed in the measured capacitances are shown to arise from the inherent resistive-capacitive DL response, charge transfer reactions, and resistively damped capacitive currents in microstructures (such as pores, pinholes, or cracks). These frequency-dependencies are typically overlooked when capacitances are related to ECSAs. The capacitance at the specimen-characteristic relaxation frequency of the resistive-capacitive DL response is proposed as a standardized capacitance-metric to estimate ECSAs. In 1 M perchloric acid, the polished gold electrode and the high-surface area carbon fleeces show ratios of capacitance-metric over surface-area of around 3.7 µF cm-2. Resistively damped currents in microstructures and low-conducting oxide layers are shown to complicate trustworthy capacitance-based estimations of ECSAs. In the second part of this study, advanced equivalent circuits models to describe the measured EIS and CV responses are presented.

Sacrificial Catalyst of Carbothermal-Shock-Synthesized 1T-MoS2 Layers for Ultralong-Lifespan Seawater Battery.

A Pt-nanoparticle-decorated 1T-MoS2 layer is designed as a sacrificial electrocatalyst by carbothermal shock (CTS) treatment to improve the energy efficiency and lifespan of seawater batteries. The phase transition of MoS2 crystals from 2H to metallic 1T─induced by the simple but potent CTS treatment─improves the oxygen-reduction-reaction (ORR) activity in seawater catholyte. In particular, the MoS2-based sacrificial catalyst effectively decreases the overpotential during charging via edge oxidation of MoS2, enhancing the cycling stability of the seawater battery. Furthermore, Pt nanoparticles are deposited onto CTS-MoS2 via an additional CTS treatment. The resulting specimen exhibits a significantly low charge/discharge potential gap of Δ0.39 V, high power density of 6.56 mW cm-2, and remarkable cycling stability up to ∼200 cycles (∼800 h). Thus, the novel strategy reported herein for the preparation of Pt-decorated 1T-MoS2 by CTS treatment could facilitate the development of efficient bifunctional electrocatalysts for fabricating seawater batteries with long service life.

Ultrathin Two-dimensional Layered Composite Carbosilicates from in situ Unzipped Carbon Nanotubes and Exfoliated Bulk Silica.

A key task in today's inorganic synthetic chemistry is to develop effective reactions, routes, and associated techniques aiming to create new functional materials with specifically desired multilevel structures and properties. Herein, we report an ultrathin two-dimensional layered composite of graphene ribbon and silicate via a simple and scalable one-pot reaction, which leads to the creation of a novel carbon-metal-silicate hybrid family: carbosilicate. The graphene ribbon is in situ formed by unzipping carbon nanotubes, while the ultrathin silicate is in situ obtained from bulk silica or commercial glass; transition metals (Fe or Ni) oxidized by water act as bridging agent, covalently bonding the two structures. The unprecedented structure combines the superior properties of the silicate and the nanocarbon, which triggers some specific novel properties. All processes during synthesis are complementary to each other. The associated synergistic chemistry could stimulate the discovery of a large class of more interesting, functionalized structures and materials.

Disentangling Phase and Morphological Evolution During the Formation of the Lithium Superionic Conductor Li10 GeP2 S12.

The structural and morphological changes of the Lithium superionic conductor Li10 GeP2 S12 , prepared via a widely used ball milling-heating method over a comprehensive heat treatment range (50 - 700 °C), are investigated. Based on the phase composition, the formation process can be distinctly separated into four zones: Educt, Intermediary, Formation, and Decomposition zone. It is found that instead of Li4 GeS4 -Li3 PS4 binary crystallization process, diversified intermediate phases, including GeS2 in different space groups, multiphasic lithium phosphosulfides (Lix Py Sz ), and cubic Li7 Ge3 PS12 phase, are involved additionally during the formation and decomposition of Li10 GeP2 S12 . Furthermore, the phase composition at temperatures around the transition temperatures of different formation zones shows a significant deviation. At 600 °C, Li10 GeP2 S12 is fully crystalline, while the sample decomposed to complex phases at 650 °C with 30 wt.% impurities, including 20 wt.% amorphous phases. These findings over such a wide temperature range are first reported and may help provide previously lacking insights into the formation and crystallinity control of Li10 GeP2 S12 .

Laplace inverted pulsed EPR relaxation to study contact between active material and carbon black in Li-organic battery cathodes.

The addition of conductive additives during electrode fabrication is standard practice to mitigate a low intrinsic electronic conductivity of most cathode materials used in Li-ion batteries. To ensure an optimal conduction pathway, these conductive additives, which generally consist of carbon particles, need to be in good contact with the active compounds. Herein, we demonstrate how a combination of pulsed electron paramagnetic resonance (EPR) relaxometry and inverse Laplace transform (ILT) can be used to study such contact. The investigated system consists of PTMA (poly(2,2,6,6-tetramethylpiperidinyloxy-4-ylmethacrylate)) monomer radicals, which is a commonly used redox unit in organic radical batteries (ORB), mixed at different ratios with Super P carbon black (CB) as the conductive additive. Inversion recovery data were acquired to determine longitudinal (T1) relaxation time constant distributions. It was observed that not only the position and relative amplitude, but also the number of relaxation modes varies as the composition of PTMA monomer and CB is changed, thereby justifying the use of ILT instead of fitting with a predetermined number of components. A hypothesis for the origin of different relaxation modes was devised. It suggests that the electrode composition may locally affect the quality of electronic contact between the active material and carbon black.

Impact of Electrostatic Interaction on Non-radiative Recombination Energy Losses in Organic Solar Cells Based on Asymmetric Acceptors.

Reducing non-radiative recombination energy loss (ΔE3 ) is one key to boosting the efficiency of organic solar cells. Although the recent studies have indicated that the Y-series asymmetric acceptors-based devices featured relatively low ΔE3 , the understanding of the energy loss mechanism derived from molecular structure change is still lagging behind. Herein, two asymmetric acceptors named BTP-Cl and BTP-2Cl with different terminals were synthesized to make a clear comparative study with the symmetric acceptor BTP-0Cl. Our results suggest that asymmetric acceptors exhibit a larger difference of electrostatic potential (ESP) in terminals and semi-molecular dipole moment, which contributes to form a stronger π-π interaction. Besides, the experimental and theoretical studies reveal that a lower ESP-induced intermolecular interaction can reduce the distribution of PM6 near the interface to enhance the built-in potential and decrease the charge transfer state ratio for asymmetric acceptors. Therefore, the devices achieve a higher exciton dissociation efficiency and lower ΔE3 . This work establishes a structure-performance relationship and provides a new perspective to understand the state-of-the-art asymmetric acceptors.

Active Interphase Enables Stable Performance for an All-Phosphate-Based Composite Cathode in an All-Solid-State Battery.

High interfacial resistance and unstable interphase between cathode active materials (CAMs) and solid-state electrolytes (SSEs) in the composite cathode are two of the main challenges in current all-solid-state batteries (ASSBs). In this work, the all-phosphate-based LiFePO4 (LFP) and Li1.3 Al0.3 Ti1.7 (PO4 )3 (LATP) composite cathode is obtained by a co-firing technique. Benefiting from the densified structure and the formed redox-active Li3- x Fe2- x - y Tix Aly (PO4 )3 (LFTAP) interphase, the mixed ion- and electron-conductive LFP/LATP composite cathode facilitates the stable operation of bulk-type ASSBs in different voltage ranges with almost no capacity degradation upon cycling. Particularly, both the LFTAP interphase and LATP electrolyte can be activated. The cell cycled between 4.1 and 2.2 V achieves a high reversible capacity of 2.8 mAh cm-2 (36 µA cm-2 , 60 °C). Furthermore, it is demonstrated that the asymmetric charge/discharge behaviors of the cells are attributed to the existence of the electrochemically active LFTAP interphase, which results in more sluggish Li+ kinetics and more expansive LFTAP plateaus during discharge compared with that of charge. This work demonstrates a simple but effective strategy to stabilize the CAM/SSE interface in high mass loading ASSBs.

Solvation and Ion-Pairing Effects of Choline Acetate Electrolyte in Protic and Aprotic Solvents Studied by NMR Titrations.

Choline-based electrolytes have been proposed as environmentally friendly and low-cost alternatives for secondary zinc air batteries. Choline acetate [Ch]+ [OAc]- in protic (D2 O) and aprotic (DMSO-d6 ) solvents has been studied by means of concentration-dependent 1 H NMR, viscosity, and density measurements. The viscosities have been calculated on the basis of the Jones-Dole equation and showed that the dominant contribution originates from short-range ion-solvent interactions. Site-specific association affinities were assigned from NMR chemical shift titrations. In DMSO-d6 , the hydroxyl group of choline was found to have the smallest dissociation constant followed by the methyl group of acetate. The corresponding Gibbs energies at low concentration were found to be in agreement with a solvent-separated ion pair (2SIP) configuration, whereas at concentrations above 300 mM, a solvent-shared ion pair (SIP) configuration was assigned. For [Ch]+ [OAc]- in D2 O, association effects were found to be weaker, attributed to the high dielectric constant of the solvent. On time scales on the order of 100 ms, NMR linewidth perturbations indicated a change in the local rotational dynamics of the ions, attributed to short-range cation-solvent interactions and not to solvent viscosity. At 184 mM, ∼ 40 % of the cations in DMSO-d6 and ∼ 10 % in D2 O were found to exhibit short-range interactions, as indicated by the linewidth perturbations. It was found that at about 300 mM, the ions in DMSO-d6 exhibit a transition from free to collective translational dynamics on time scales on the order of 400 ms. In DMSO-d6 , both ions were found to be almost equally solvated, whereas in D2 O solvation of acetate was stronger, as indicated by the obtained effective hydrodynamic radii. For [Ch]+ [OAc]- in DMSO-d6 , the results suggest a solvent-shared ion association with weak H-bonding interactions for concentrations between 0.3-1 M. Overall, the extent of ion association in solvents such as DMSO is not expected to significantly limit charge transport and hinder the performance of choline-based electrolytes.

Nanoscale visualization of metallic electrodeposition in a well-controlled chemical environment.

Liquid phase transmission electron microscopy (TEM) provides a useful means to study a wide range of dynamics in solution with near-atomic spatial resolution and sub-microsecond temporal resolution. However, it is still a challenge to control the chemical environment (such as the flow of liquid, flow rate, and the liquid composition) in a liquid cell, and evaluate its effect on the various dynamic phenomena. In this work, we have systematically demonstrated the flow performance of anin situliquid TEM system, which is based on 'on-chip flow' driven by external pressure pumps. We studied the effects of different chemical environments in the liquid cell as well as the electrochemical potential on the deposition and dissolution behavior of Cu crystals. The results show that uniform Cu deposition can be obtained at a higher liquid flow rate (1.38µl min-1), while at a lower liquid flow rate (0.1µl min-1), the growth of Cu dendrites was observed. Dendrite formation could be further promoted byin situaddition of foreign ions, such as phosphates. The generality of this technique was confirmed by studying Zn electrodeposition. Our direct observations not only provide new insights into understanding the nucleation and growth but also give guidelines for the design and synthesis of desired nanostructures for specific applications. Finally, the capability of controlling the chemical environment adds another dimension to the existing liquid phase TEM technique, extending the possibilities to study a wide range of dynamic phenomena in liquid media.

Double layer capacitances analysed with impedance spectroscopy and cyclic voltammetry: validity and limits of the constant phase element parameterization.

Routinely, cyclic voltammetry (CV) or electrochemical impedance spectroscopy (EIS) are used in electrochemistry to probe the current response of a specimen. For the interpretation of the response, constant phase elements (CPEs) are used in the frequency domain based impedance calculus to parameterize the double layer. In this study, the double layer responses to the two measurement techniques are compared by probing a model-type polished gold electrode under potential and amplitude variation. The equivalent circuit that describes the double layer includes a CPE and is parameterized by impedance data, while a computational impedance-based Fourier transform model (source code disclosed) is used to describe the CV response. With CV, the measured and modelled responses show good agreement at amplitudes below 0.2 V and within a certain scan rate window. At larger amplitudes, the ion arrangement in the double layer is actively changed by the measurement, leading to potential dependencies and deviations from the CPE behaviour. These varying contributions to the impedance measurements are not respected in the impedance calculus that relies on a sinusoidal response. The transition from perturbations of the double layer equilibrium to distortions of the ion arrangements is analysed with both measurement methods.

Dynamics of [Pyr13][Tf2N] ionic liquid confined to carbon black.

The intrinsic ionic nature of room temperature ionic liquids (RTILs) bears the potential to replace classical aqueous electrolytes in electrochemical applications, for example in metal-air batteries. For a systematic adjustment of RTIL properties in porous cathodes, the ionic arrangement under confinement is of prime importance. Using spectrally resolved pulsed gradient stimulated echo nuclear magnetic resonance (PGSTE-NMR) and spin-lattice NMR relaxation time (T1) distributions, the dynamics of 1-methyl-1-propylpyrrolidiniumbis(trifluoromethylsulfonyl)imide ([Pyr13][Tf2N]) confined to carbon black were investigated. A considerable dependence of the [PYR13] mobility on the loading fraction of the carbon black pore space was found. There is evidence for a preferential layering of the RTIL adjacent to the carbon surface and a dependence of the ionic configuration on the local structure of the carbon surface. The inversion efficiency of inversion-recovery T1 data indicates a quasi-stationary layer at the carbon surface with solid-like properties, where the bulk-like properties of the RTIL are adopted as the distance to the surface increases. From the NMR diffusion data an intermediate layer between the quasi-stationary and the bulk-like RTIL is evident. This layer shows a particularly strong pore space loading dependence. While it has an anisotropic, two-dimensional mobility with reduced diffusion perpendicular to the surface at any loading, when it interfaces a gas phase at low loading its mobility is higher than bulk diffusion by up to an order of magnitude and chemical exchange with other layers is low. This layer appears to be of particular importance for the ion exchange between RTIL environments with different spacing from the carbon surface and hence crucial for the overall dynamics of RTILs in the investigated porous environment.

Long-run in operando NMR to investigate the evolution and degradation of battery cells.

To improve the lifetime of lithium-ion batteries, a detailed understanding of the degradation mechanisms is essential. Nuclear magnetic resonance (NMR) is able to unravel the reversible as well as irreversible transient changes of composition, shape and morphology in a battery cell. Using a newly developed cylindrical battery container free of metallic components in combination with a numerically optimized saddle coil, in operando NMR investigations of battery cells over hundreds of charge/discharge cycles are presented. Alternating with NMR data acquisition, electrochemical impedance spectra (EIS) can be recorded, which enables correlative analysis of the two techniques. Long-run in operando NMR measurements on a Li metal vs. graphite cell reveal the formation and evolution of mossy and dendritic Li microstructures over a period of 1000 h, which illustrates the capabilities of NMR to identify dendrite mitigation strategies in cells operated under realistic conditions.

Monitoring local redox processes in LiNi0.5Mn1.5O4 battery cathode material by in operando EPR spectroscopy.

Despite the multitude of analytical methods available to characterize battery cathode materials, identifying the factors responsible for material aging is still challenging. We present the first investigation of transient redox processes in a spinel cathode during electrochemical cycling of a lithium ion battery by in operando electron paramagnetic resonance (EPR). The battery contains a LiNi0.5Mn1.5O4 (LNMO) spinel cathode, which is a material whose magnetic interactions are well understood. The evolution of the EPR signal in combination with electrochemical measurements shows the impact of Mn3+ on the Li+ motion inside the spinel. Moreover, state of charge dependent linewidth variations confirm the formation of a solid solution for slow cycling, which is taken over by mixed models of solid solution and two-phase formation for fast cycling due to kinetic restrictions and overpotentials. Long-term measurements for 480 h showed the stability of the investigated LNMO, but also small amounts of cathode degradation products became visible. The results point out how local, exchange mediated magnetic interactions in cathode materials are linked with battery performance and can be used for material characterization.

Power-to-Syngas: An Enabling Technology for the Transition of the Energy System?

Power-to-X concepts promise a reduction of greenhouse gas emissions simultaneously guaranteeing a safe energy supply even at high share of renewable power generation, thus becoming a cornerstone of a sustainable energy system. Power-to-syngas, that is, the electrochemical conversion of steam and carbon dioxide with the use of renewably generated electricity to syngas for the production of synfuels and high-value chemicals, offers an efficient technology to couple different energy-intense sectors, such as "traffic and transportation" and "chemical industry". Syngas produced by co-electrolysis can thus be regarded as a key-enabling step for a transition of the energy system, which offers additionally features of CO2 -valorization and closed carbon cycles. Here, we discuss advantages and current limitations of low- and high-temperature co-electrolysis. Advances in both fundamental understanding of the basic reaction schemes and stable high-performance materials are essential to further promote co-electrolysis.

Singlet Oxygen Formation during the Charging Process of an Aprotic Lithium-Oxygen Battery.

Aprotic lithium-oxygen (Li-O2 ) batteries have attracted considerable attention in recent years owing to their outstanding theoretical energy density. A major challenge is their poor reversibility caused by degradation reactions, which mainly occur during battery charge and are still poorly understood. Herein, we show that singlet oxygen ((1) Δg ) is formed upon Li2 O2 oxidation at potentials above 3.5 V. Singlet oxygen was detected through a reaction with a spin trap to form a stable radical that was observed by time- and voltage-resolved in operando EPR spectroscopy in a purpose-built spectroelectrochemical cell. According to our estimate, a lower limit of approximately 0.5 % of the evolved oxygen is singlet oxygen. The occurrence of highly reactive singlet oxygen might be the long-overlooked missing link in the understanding of the electrolyte degradation and carbon corrosion reactions that occur during the charging of Li-O2 cells.

Machine Learning Isotropic g Values of Radical Polymers.

Methods for electronic structure computations, such as density functional theory (DFT), are routinely used for the calculation of spectroscopic parameters to establish and validate structure-parameter correlations. DFT calculations, however, are computationally expensive for large systems such as polymers. This work explores the machine learning (ML) of isotropic g values, giso, obtained from electron paramagnetic resonance (EPR) experiments of an organic radical polymer. An ML model based on regression trees is trained on DFT-calculated g values of poly(2,2,6,6-tetramethylpiperidinyloxy-4-yl methacrylate) (PTMA) polymer structures extracted from different time frames of a molecular dynamics trajectory. The DFT-derived g values, gisocalc, for different radical densities of PTMA, are compared against experimentally derived g values obtained from in operando EPR measurements of a PTMA-based organic radical battery. The ML-predicted giso values, gisopred, were compared with gisocalc to evaluate the performance of the model. Mean deviations of gisopred from gisocalc were found to be on the order of 0.0001. Furthermore, a performance evaluation on test structures from a separate MD trajectory indicated that the model is sensitive to the radical density and efficiently learns to predict giso values even for radical densities that were not part of the training data set. Since our trained model can reproduce the changes in giso along the MD trajectory and is sensitive to the extent of equilibration of the polymer structure, it is a promising alternative to computationally more expensive DFT methods, particularly for large systems that cannot be easily represented by a smaller model system.

Post-treatment strategies for pyrophoric KOH-activated carbon nanofibres.

The effect of two atmospheric post-treatment conditions directly after the KOH activation of polyacrylonitrile-based nanofibres is studied in this work. As post-treatment different N2 : O2 flow conditions, namely high O2-flow and low O2-flow, are applied and their impact on occurring reactions and carbon nanofibres' properties is studied by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), Raman spectroscopy, elemental analysis and CO2 and Ar gas adsorption. At high O2-flow conditions a pyrophoric effect was observed on the KOH-activated carbon nanofibers. Based on the obtained results from the TGA and DSC the pyrophoric effect is attributed to the oxidation reactions of metallic potassium formed during the KOH activation process and a consequent carbon combustion reaction. Suppression of this pyrophoric effect is achieved using the low O2-flow conditions due to a lower heat formation of the potassium oxidation and the absence of carbon combustion. Compared to the high O2-flow samples no partial destruction of the carbon nanofibers is observed in the SEM images. The determination of the adsorption isotherms, the surface area, the pore size distribution and the isosteric enthalpies of adsorption show the superior properties under low O2-flow conditions. The present micropore volume is increased from 0.424 cm3 g-1 at high O2-flow to 0.806 cm3 g-1 for low O2-flow samples, resulting in an increase of CO2 adsorption capacity of 38% up to 6.6 mmol g-1 at 1 bar. This significant improvement clearly points out the importance of considering highly exothermic potassium oxidation reactions and possible post-treatment strategies when applying KOH activation to electrospun carbon nanofiber materials.