ABSTRACT
In traditional optical wireless communication (OWC) systems, the simultaneous use of multiple sets of light-emitting diodes (LEDs) and photodetectors (PDs) increases the system complexity and instability. Here we report bifunctional light-emitting photodetectors (LEPDs) fabricated with quasi-2D perovskite (F-PEA)2Cs4Pb5I11Br5 as light-emitting/detecting layers for efficient, miniaturized, and intelligent bidirectional OWC. By simply changing the solvent composition of the precursor solution and using antisolvent engineering, we manipulated the crystal orientation and phase distribution of (F-PEA)2Cs4Pb5I11Br5, realizing high irradiance (4.36 µW cm-2) and a -3 dB refresh rate (0.21 MHz) of electroluminescence in LED mode as well as low noise (below 1 pA Hz-1/2) and high responsivity (0.1 A W-1) in PD mode. The rapid and accurate OWC process was demonstrated through interaction of LEPDs. We also demonstrated the high-fidelity compression and digitization of high-resolution (256 × 256 pixels) color images using the four-step phase shift method to realize intelligent encrypted image OWC.
ABSTRACT
Although two-dimensional (2D) chiral sheet structures are attractive because of their unique chemical and physical properties, single layer 2D chiral network structures with switchable pore interior remain elusive. Here we report spontaneous chirality induction in a single layer 2D network structure formed from the self-assembly of tetrapod azobenzene molecules. The chirality induction arises from multiple sublayers slipped in a preferred direction in which the sublayer consists of unidentical molecular arrangements in the in-plane a and b directions, breaking both the plane of symmetry and inversion symmetry. The protruded azobenzene units in the pore interior can be selectively isomerized upon UV irradiation, resulting in a reversible deformation of the chiral pores while maintaining the 2D frameworks. The chiral network can thus selectively entrap one enantiomer from a racemic solution with near perfect enantioselectivity, and then release it upon UV irradiation.
ABSTRACT
The low-dimensional halide perovskites have attracted increasing attention due to their improved moisture stability, reduced defects, and suppressed ions migration in many optoelectronic devices such as solar cells, light-emitting diodes, X-ray detectors, and so on. However, they are still limited by their large band gap and short charge carriers' diffusion length. Here, we demonstrate that the introduction of metal ions into organic interlayers of two-dimensional (2D) perovskite by cross-linking the copper paddle-wheel cluster-based lead bromide ([Cu(O2 C-(CH2 )3 -NH3 )2 ]PbBr4 ) perovskite single crystals with coordination bonds can not only significantly reduce the perovskite band gap to 0.96â eV to boost the X-ray induced charge carriers, but can also selectively improve the charge carriers' transport along the out-of-plane direction and blocking the ions motion paths. The [Cu(O2 C-(CH2 )3 -NH3 )2 ]PbBr4 single-crystal device can reach a record charges/ions collection ratio of 1.69×1018 ±4.7 %â µGyair -1 s, and exhibit a large sensitivity of 1.14×105 ±7%â µC Gyair -1 cm-2 with the lowest detectable dose rate of 56â nGyair s-1 under 120â keV X-rays irradiation. In addition, [Cu(O2 C-(CH2 )3 -NH3 )2 ]PbBr4 single-crystal detector exposed to the air without any encapsulation shows excellent X-ray imaging capability with long-term operational stability without any attenuation of 120â days.
ABSTRACT
Solution-processed perovskites as emerging semiconductors have achieved unprecedented milestones in sensor optoelectric devices. Stability along with the device noise issues are the major obstacle for photodetectors to compete with the traditional devices. Here, we demonstrated that l-ascorbic acid (l-AA) as a polyhydroxy ester can coordinate with the amino group of formamidine cations (FA+) through multiple hydrogen bond interactions to stabilize the perovskite, which protect the FA+ ions from nucleophile attack and effectively suppress the degradation of FA+ ions, improving the perovskite stability and suppressing the device noise to below 0.3 pA Hz-1/2 with a large linear dynamic range of 239 dB. The dual functions of l-AA enable the perovskite photodetector to have a high detectivity of 1012 Jones. The self-powered device works with no energy consumption and maintains an undegraded performance over 1200 h of inspection at ambient conditions, which is promising for infrastructure construction, signal sensing, and real-time information delivery.
ABSTRACT
Although considerable effort in recent years has been devoted to the development of two-dimensional nanostructures, single-layered chiral sheet structures with a lateral assembly of discrete clusters remain elusive. Here, we report single-layered chiral 2D sheet structures with dual chiral void spaces in which discrete clusters of planar aromatic segments are arranged with in-plane AB order in aqueous methanol solution. The chirality of the sheet is induced by the slipped-cofacial stacks of rectangular plate-like aromatic segments in the discrete clusters which are arranged laterally with up and down packing, resulting in dual chiral void spaces. The chiral nanosheets function as superfast enantiomer separation nanomaterials, which rapidly absorb a single enantiomer from a racemic mixture with greater than 99 % ee.
ABSTRACT
Reported here is the use of single-layered, chiral porous sheets with induced pore chirality for repeatable asymmetric transformations and self-separation without the need for chiral catalysts or chiral auxiliaries. The asymmetric induction is driven by chiral fixation of absorbed achiral substrates inside the chiral pores for transformation into enantiopure products with enantioselectivities of greater than 99 % ee. When the conversion is completed, the products are spontaneously separated out of the pores, enabling the porous sheets to perform repeated cycles of converting achiral substrates into chiral products for release without compromising pore performance. Confinement of achiral substrates into two-dimensional chiral porous materials provides access to a highly efficient alternative to current asymmetric synthesis methodologies.
ABSTRACT
Cornus officinalis and Dioscorea opposita are two traditional Chinese medicines widely used in China for treating diabetes mellitus and its complications, such as diabetic cardiomyopathy. Morroniside (Mor) of Cornus officinalis and diosgenin (Dio) of Dioscorea opposita formed an innovative formula named M + D. The aims of the present study were to investigate myocardial protective effect of M + D on diabetic cardiomyopathy (DCM) through the inhibition of expression levels of caspase-3 protein, and identify the advantage of M + D compared with Mor, Dio, and the positive drug metformin (Met). We detected cell viability, cell apoptosis, intracellular reactive oxygen species (ROS) levels, and the expression levels of Bcl-2, Bax, and caspase-3 protein in rat cardiomyocytes. In result, Mor, Dio, and M + D increased cell viability, inhibited cell apoptosis and decreased ROS levels. Additionally, the expression of Bax and Bcl-2 protein was modulated and the expression levels of caspase-3 protein were markedly decreased. Among the treatment groups, M + D produced the most prominent effects. In conclusion, our data showed for the first time that Mor, Dio, and M + D prevented high glucose (HG)-induced myocardial injury by reducing oxidative stress and apoptosis in rat cardiomyocytes. Among all the groups, M + D produced the strongest effect, while Mor and Dio produced weaker effects.
Subject(s)
Diosgenin/pharmacology , Glucose/toxicity , Glycosides/pharmacology , Myocytes, Cardiac/cytology , Animals , Apoptosis/drug effects , Caspase 3/metabolism , Cell Survival , Cells, Cultured , Diabetic Cardiomyopathies/metabolism , Diabetic Cardiomyopathies/prevention & control , Drug Combinations , Gene Expression Regulation/drug effects , Myocytes, Cardiac/drug effects , Myocytes, Cardiac/metabolism , Rats , Reactive Oxygen Species/metabolismABSTRACT
Metal halide scintillators serve as promising candidates for X-ray detection due to their high attenuation coefficients, high light yields, and low-cost solution-processable characteristics. However, the issues of humidity/thermal quenching and mechanical fragility, remain obstacles to the broad and diversified development of metal halide scintillators. Here, this work reports a lead-free, water-stable, stretchable, and self-healing (ethylenebis-triphenylphosphonium manganese (II) bromide (C38H34P2)MnBr4 organogel scintillator that meets X-ray imaging in complex scenarios. The robust organogel scintillator can be stretched with elongation up to 1300% while maintaining the scintillation properties. Activated by the dynamic hydrogen bonds and coordination bonds design, the organogel scintillator exhibits excellent self-healing properties at room temperature to alleviate the vignetting problem of the rigid scintillator films, the X-ray imaging resolution can reach 16.7 lp mm-1. The organogel scintillator can also realize flexible and self-healing X-ray imaging in water, providing a design path for portable devices in harsh conditions.
ABSTRACT
Advanced photodetectors with intelligent functions are expected to take an important role in future technology. However, completing complex detection tasks within a limited number of pixels is still challenging. Here, we report a differential perovskite hemispherical photodetector serving as a smart locator for intelligent imaging and location tracking. The high external quantum efficiency (~1000%) and low noise (10-13 A Hz-0.5) of perovskite hemispherical photodetector enable stable and large variations in signal response. Analysing the differential light response of only 8 pixels with the computer algorithm can realize the capability of colorful imaging and a computational spectral resolution of 4.7 nm in a low-cost and lensless device geometry. Through machine learning to mimic the differential current signal under different applied biases, one more dimensional detection information can be recorded, for dynamically tracking the running trajectory of an object in a three-dimensional space or two-dimensional plane with a color classification function.
ABSTRACT
Tin perovskites have emerged as a promising alternative material to address the toxicity of lead perovskites and the low bandgap of around 1.1 eV is also compatible with tandem solar cell applications. Nevertheless, the optoelectronic performance of solution-processed tin perovskite single-crystal counterparts still lags behind because of the tin instability under ambient conditions during crystal growth and limited reductants to protect the Sn2+ ions from oxidation. Here, the reductant engineering to grow high-quality tin perovskite single crystals under ambient conditions is studied. Oxalic acid (H2 C2 O4 ) serves as an excellent reductant and sacrificial agent to protect Sn2+ ions in methanol due to its suitable redox potential of -0.49 V, and the CO2 as the oxidation product in the gas state can be easily separated from the solution. The FPEA2 SnI4 single crystal grown by this strategy exhibits low trap density perovskite surface by constructing an FPEA2 PbI4 -FPEA2 SnI4 (FPI-FSI) single crystal heterojunction for X-ray detection. An improved X-ray sensitivity of 1.7 × 105 µC Gy-1 cm-2 is realized in the heterojunction device, outperforming the control FPEA2 PbI4 counterpart.
ABSTRACT
The diversity of organic cations greatly enriches the species of 2D perovskites; traditional 2D Ruddlesden-Popper (RP) and Dion-Jacobson (DJ) perovskites are synthesized by two different organic amines. Here, according to the difference in pKa values between conjugated acids of monoprotonated and biprotonated 4-(2-Aminoethyl)pyridine (4AEPy) ions, the 2D perovskites of RP (4AEPy)2 PbI4 and DJ (4AEPy)PbI4 from same organic amine is reported, which can realize reversible transformation under the treatment of HI and NH3 , respectively. The interaction of N-H···N hydrogen bond between adjacent organic molecules in (4AEPy)2 PbI4 leads to the bending conformation of ethylamine groups, which results in a 2.4 Å reduction in layer spacing compared to typical phenylethylamine lead iodine ((PEA)2 PbI4 ) 2D perovskite. Besides, the ethylamine groups of organic layers in (4AEPy)PbI4 are deeply inserted into octahedral cavities and directly participate in the construction of the conduction band minimum, which leads to a small exciton binding energy of 27.3 meV to generate free charges. The stronger coupling between the organic and inorganic layers and the minor exciton binding energy can promote the DJ phase to possess a more stable structure and better optoelectronic properties. Thus the (4AEPy)PbI4 device displays better light response and X-ray detection capability with a high sensitivity of 5627 µC Gyair -1 cm-2 and the lowest detectable dose rate of 20 nGyair s-1 .
ABSTRACT
Sphere imagers featuring specific wavelength recognition and wide-angle imaging are required to meet the fast development of modern technology. However, it is still challenging to deposit high-quality photosensitive layers on sphere substrates from low-cost solution processes. Here we report spray-coated quasi-two-dimensional phenylethylammonium/formamidinium lead halide (PEA2FAn-1PbnX3n+1) perovskite hemispherical photodetectors. The crystallization speed is manipulated by perovskite compositions, and the film thickness can be controlled by spray-coating cycles and solution concentration from tens of nanometers to hundreds of micrometers with a fast velocity of 1.28 × 10-4 cm3 s-1. The lens-free hemispherical photodetectors allow light response at a wide incident angle of 180°. Simultaneously, the wavelength selective response from visible to the near-infrared range is achieved with full width at half maximums (FWHMs) of ~20 nm, comparable to single-crystal devices. Wide-angle and wavelength-selective imaging are also demonstrated, which can find potential applications in intelligent recognition and intraoperative navigated surgery.
ABSTRACT
Staphylococcus aureus is one of the major foodborne pathogens. Efficient detection and isolation of Staphylococcus aureus from complex samples are crucial. Herein, we report a concise strategy to detect of Staphylococcus aureus with high sensitivity and specificity, based on N-Succinyl-Chitosan doping bacteria-imprinted composite film and aggregation-induced emission (AIE)-featuring fluorescence sensor. The good shaping and mechanical properties of polydimethylsiloxane provide a specific recognition site suitable for Staphylococcus aureus. For the first time, chitosan derivatives is combined with polydimethylsiloxane to prepare a two-component composite film, which possesses a remarkable absorption performance of Staphylococcus aureus using the natural excellent absorption property of chitosan. The positive charged AIE-featuring Au(I)-disulfide nanoparticles realized the quantitative characterization of Staphylococcus aureus without cooperation with bio-recognition elements. To conclude, this study provides new possibilities for the manufacture of highly efficient bacterial separators with superior performance and facilitates the application of unlabeled nanoparticles in quantitative analysis.
Subject(s)
Chitosan , Staphylococcus aureus , Anti-Bacterial Agents , Bacteria , FluorescenceABSTRACT
Metal halide perovskite scintillators encounter unprecedented opportunities in indirect ionizing radiation detection due to their high quantum yields. However, the long scintillation lifetime of microseconds upon irradiation, known as the afterglow phenomenon, obviously limits their fast development. Here, a new type of hybrid X-ray detector wafer combining direct methylamine lead iodide (MAPbI3 ) semiconductor and indirect zero-dimensional cesium copper iodide (Cs3 Cu2 I5 ) scintillator through low-cost fast tableting processes is reported. Due to the fast energy transfer from Cs3 Cu2 I5 to MAPbI3 , the device response time to X-rays is dramatically reduced by nearly 30 times to 36.6 ns, which enables fast X-ray detection capability by a large area detector arrays within 1 s. Moreover, Cs3 Cu2 I5 exists at the grain boundaries of MAPbI3 crystals, and blocks the paths of mobile ions of perovskite, leading to the lowest detectable dose rate of hybrid X-ray detector is thus reduced by 1.5 times compared with control MAPbI3 direct-type semiconductor, and 10 times compared with the Cs3 Cu2 I5 indirect-type scintillator. The direct/indirect hybrid wafer also exhibits improved operation stability at ambient conditions without any encapsulation. This new kind of hybrid X-ray detectors provides strong competitiveness by combining the advantages of both direct perovskite semiconductors and indirect perovskite scintillators for next-generation products.
ABSTRACT
Quasi-2D perovskites have been demonstrated to be competitive materials in the photodetection fields due to the enhanced moisture stability by large organic cations. However, as the increasing demands of modern technology, it is still challenging to combine the flexibility with the capability of weak light detection in a low-cost way. Here, amides, carboxylic acids, and anhydrides groups-rich carbonized polymer dots (CPDs) were employed to fill in the perovskite grain boundaries, which can passivate the point defects of perovskite by coordinating with the unbonded Pb atoms, and reduce the leakage current. Weak light detection capability was demonstrated by directly resolving light with an intensity of 10.1 pW cm-2. More importantly, the stretchable polymer chains on CPDs strongly interact with perovskite ions through multiple supramolecular interactions, and extend the stretchable properties to the perovskite/CPDs composites, which can maintain the integral structure stability during the deformation of perovskite crystals and restricted any crack by releasing the film strain. Our fabricated devices show extraordinary flexible stability in the bending-dependent response tests. The viscoelasticity of CPDs improves the bending stability of the flexible quasi-2D perovskite photodetectors, and device performance shows no degradation after bending 10000 times, comparable or even outperforming the dominating flexible photodetectors.
ABSTRACT
2D perovskite single crystals have emerged as excellent optoelectronic materials owing to their unique anisotropic properties. However, growing large 2D perovskite single crystals remains challenging and time-consuming. Here, a new composition of lead-free 2D perovskite-4-fluorophenethylammonium bismuth iodide [(F-PEA)3 BiI6 ] is reported. An oriented bulk 2D wafer with a large area of 1.33 cm2 is obtained by tableting disordered 2D perovskite powders, resulting in anisotropic resistivities of 5 × 1010 and 2 × 1011 Ω cm in the lateral and vertical directions, respectively. Trivalent Bi3+ ions are employed to achieve a stronger ionic bonding energy with I- ions, which intrinsically suppress the ion-migration effect. Thus, the oriented wafer presents good capabilities in both charge collection and ion-migration suppression under a large applied bias along the out-of-plane direction, making it suitable for low-dosage X-ray detection. The large-area wafer shows a sensitive response to hard X-rays operated at a tube voltage of 120 kVp with the lowest detectable dose rate of 30 nGy s-1 . Thus, the fast tableting process is a facile and effective strategy to synthesize large-area, oriented 2D wafers, showing excellent X-ray detection performance and operational stability that are comparable to those of 2D perovskite single crystals.
ABSTRACT
Methylammonium lead tribromide perovskite single crystals have been demonstrated to be good candidates as sensitive X-ray detectors in direct detection mode in recent years. However, its X-ray detection performance based on the orientation of different facets is still not clear. Here, we developed a facile strategy to chemically expose the [110] facet of single crystals from low-cost solution processes by tailoring the nonstoichiometry of feeding ions to selectively suppress the growth of the [100] facet. In contrast to physically cutting and sawing single-crystal ingots, this avoids damage to the fragile single crystals as well as orientation errors, more suitable for the naturally soft lattice. Compared to the [100] facet, the exposed [110] facet of perovskite single crystals exhibits a smaller trap density and excellent charge carrier transportation properties, leading to an improved sensitivity of 3928.3 µC/Gyair/cm2 to 120 keV hard X-rays, which potentially outperforms the currently dominating CsI scintillator of a commercial digital radiography (DR) medical imager for a routine health check.
ABSTRACT
Two alleles of the HG1 gene, which encodes a putative GABA receptor alpha/gamma subunit, were isolated from Haemonchus contortus. These two alleles were shown previously to be associated with ivermectin susceptibility (HG1A) and resistance (HG1E), respectively. Sequence analysis indicates that they differ in four amino acids. To explore the functional properties of the two alleles, a full-length cDNA encoding the beta subunit, a key functional component of the GABA receptor, was isolated from Caenorhabditis elegans (gab-1, corresponding to the GenBank locus ZC482.1) and coexpressed in Xenopus oocytes with the HG1 alleles. When gab-1 was coexpressed with either the HG1A allele or the HG1E allele in Xenopus oocytes, gamma-aminobutyric acid (GABA)-responsive channels with different sensitivity to the agonist were formed. The effects of ivermectin on the hetero-oligomeric receptors were determined. Application of ivermectin alone had no effect on the receptors. However, when coapplied with 10 micro m GABA, ivermectin potentiated the GABA-evoked current of the GAB-1/HG1A receptor, but attenuated the GABA response of the GAB-1/HG1E receptor. We demonstrated that the coexpressed HG1 and GAB-1 receptors are GABA-responsive, and provide evidence for the possible involvement of GABA receptors in the mechanism of ivermectin resistance.
Subject(s)
Caenorhabditis elegans Proteins/genetics , Drug Resistance/genetics , Ivermectin/pharmacology , Receptors, GABA-A/genetics , Alleles , Amino Acid Sequence , Animals , Base Sequence , Binding, Competitive/drug effects , Caenorhabditis elegans , Caenorhabditis elegans Proteins/biosynthesis , Electrophysiology , Gene Expression , Haemonchus , Helminth Proteins/biosynthesis , Helminth Proteins/genetics , Ligands , Molecular Sequence Data , Oocytes/drug effects , Oocytes/metabolism , Phylogeny , Protein Subunits/biosynthesis , Protein Subunits/genetics , Receptors, GABA-A/biosynthesis , Sequence Alignment , Sequence Homology, Amino Acid , Transfection , Xenopus , gamma-Aminobutyric Acid/pharmacologyABSTRACT
Two full-length glutamate-gated chloride channel (GluCl) cDNAs, encoding GluClalpha3 and GluClbeta subunits, were cloned from ivermectin-susceptible (IVS) and -resistant (IVR) Cooperia oncophora adult worms. The IVS and IVR GluClalpha3 subunits differ at three amino acid positions, while the IVS and IVR GluClbeta subunits differ at two amino acid positions. The aim of this study was to determine whether mutations in the IVR subunits affect agonist sensitivity. The subunits were expressed singly and in combination in Xenopus laevis oocytes. Electrophysiological whole-cell voltage-clamp recordings showed that mutations in the IVR GluClalpha3 caused a modest but significant threefold loss of sensitivity to glutamate, the natural ligand for GluCl receptors. As well, a significant decrease in sensitivity to the anthelmintics ivermectin and moxidectin was observed in the IVR GluClalpha3 receptor. Mutations in the IVR GluClbeta subunit abolished glutamate sensitivity. Co-expressing the IVS GluClalpha3 and GluClbeta subunits resulted in heteromeric channels that were more sensitive to glutamate than the respective homomeric channels, demonstrating co-assembly of the subunits. In contrast, the heteromeric IVR channels were less sensitive to glutamate than the homomeric IVR GluClalpha3 channels. The heteromeric IVS channels were significantly more sensitive to glutamate than the heteromeric IVR channels. Of the three amino acids distinguishing the IVS and IVR GluClalpha3 subunits, only one of them, L256F, accounted for the differences in response between the IVS and IVR GluClalpha3 homomeric channels.