Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 20 de 29
Filter
1.
Appl Opt ; 60(29): 9042-9053, 2021 Oct 10.
Article in English | MEDLINE | ID: mdl-34623984

ABSTRACT

In the present study, the capabilities and limitations of surface light scattering (SLS) experiments in reflection geometry are investigated. Based on the study of the transparent reference fluid toluene at 303.15 K over a wide range of wave vectors between (0.3and6.6)×105m-1, the performance of two different detection schemes analyzing light scattered from the vapor-liquid interface in a perpendicular and non-perpendicular direction is assessed. Considering various aspects such as the quality of the heterodyne correlation functions, the input information for data evaluation, and the line-broadening effects, both detection schemes show comparable overall efficiency. For wave vectors larger than 4.5×105m-1, where line-broadening effects are suppressed, the results obtained for liquid viscosity and surface tension agree with measurements in transmission geometry, validating the capability of the apparatus. For wave vectors smaller than 1.5×105m-1, the SLS signals are distinctly affected by line-broadening effects, which will result in erroneous values for surface tension and in particular viscosity, even if empirical fitting approaches commonly used in literature are applied. The modeling of the influence of line broadening on the measurements results by a simple Gaussian-weighted sum of individual damped oscillations reveals the increasing complexity of the underlying wave vector distribution toward smaller wave vectors chosen for the scattering geometry.

2.
J Chem Eng Data ; 64(9)2020.
Article in English | MEDLINE | ID: mdl-33654329

ABSTRACT

In the present study, the simultaneous and accurate determination of liquid viscosity and surface tension of the n-alkanes n-hexane (n-C6H14), n-octane (n-C8H18), n-decane (n-C10H22), and n-hexadecane (n-C16H34) by surface light scattering (SLS) in thermodynamic equilibrium is demonstrated. Measurements have been performed over a wide temperature range from 283.15 K up to 473.15 K for n-C6H14, 523.15 K for n-C8H18, and 573.15 K for n-C10H22 as well as n-C16H34. The liquid dynamic viscosity and surface tension data with average total measurement uncertainties (k = 2) of (2.0 and 1.7) % agree with the available literature and contribute to a new database at high temperatures. Over the entire temperature range, a Vogel-type equation for the dynamic viscosity and a modified van der Waals equation for the surface tension represent the measured data for the four n-alkanes within experimental uncertainties. By also considering our former SLS data for n-dodecane (n-C12H26) and n-octacosane (n-C28H58), empirical models for the liquid viscosity and surface tension of n-alkanes were developed as a function of temperature and carbon number covering values between 6 and 28. Agreement between these models and reference correlations for further selected n-alkanes which were not included in the development procedure was found.

3.
J Phys Chem B ; 127(49): 10647-10658, 2023 Dec 14.
Article in English | MEDLINE | ID: mdl-38038699

ABSTRACT

Surfactant monolayers at liquid interfaces induce a viscoelastic behavior that influences the dynamics of surface fluctuations probed by surface light scattering (SLS). Recent thermophysical property research on viscosity and interfacial tension of liquid organic hydrogen carrier (LOHC) systems based on diphenylmethane suggested that such viscoelastic effects may also be present here, although not being expected a priori. To prove the hypothesis that the LOHC intermediate cyclohexylphenylmethane (H6-DPM) can induce a surfactant-like behavior, binary mixtures of diphenylmethane (H0-DPM) or dicyclohexylmethane (H12-DPM) with small amounts of H6-DPM were studied by SLS in combination with conventional viscometry and tensiometry and molecular dynamics simulations between (303 and 473) K. Only in mixtures with H0-DPM which has a slightly larger surface tension than H6-DPM, the presence of the latter compound causes a significant effect on the dynamics of surface fluctuations, especially on their damping. In analogy to the concentration-dependent behavior observed for a monolayer of a highly amphiphilic ionic surfactant on the surface of water at ambient temperature, the orientation of H6-DPM molecules with respect to the surface appears to change from a preferentially perpendicular to a parallel alignment with increasing temperature. This demonstrates that viscoelastic effects including accompanied surface orientation effects can be resolved by SLS even for weakly asymmetric surface-active molecules such as H6-DPM in its diluted mixtures with very similar species.

4.
J Colloid Interface Sci ; 641: 251-264, 2023 Jul.
Article in English | MEDLINE | ID: mdl-36933471

ABSTRACT

HYPOTHESIS: The applicability of the dynamic light scattering method for the determination of particle diffusivity under confinement without applying refractive index matching was not adequately explored so far. The confinement effect on particle diffusion in a porous material which is relevant for particle chromatography has also not yet been fully characterized. EXPERIMENTS: Dynamic light scattering experiments were performed for unimodal dispersions of 11-mercaptoundecanoic acid-capped gold nanoparticles. Diffusion coefficients of gold nanoparticles in porous silica monoliths were determined without limiting refractive index matching fluids. Comparative experiments were also performed with the same nanoparticles and porous silica monolith but applying refractive index matching. FINDINGS: Two distinct diffusivities could be determined inside the porous silica monolith, both smaller than that in free media, showing a slowing-down of the diffusion processes of nanoparticles under confinement. While the larger diffusivity can be related to the slightly slowed-down diffusion of particles in the bulk of the pores and in the necks connecting individual pores, the smaller diffusivity might be related to the diffusion of particles near the pore walls. It shows that the dynamic light scattering method with a heterodyne detection scheme can be used as a reliable and competitive tool for determining particle diffusion under confinement.

5.
J Colloid Interface Sci ; 626: 899-915, 2022 Nov 15.
Article in English | MEDLINE | ID: mdl-35835041

ABSTRACT

HYPOTHESIS: Near the critical damping of surface fluctuations, surface light scattering (SLS) signals are affected by the rotational flow in the bulk of the fluid. The adequate consideration of this bulk shear mode is essential for a reliable determination of viscosity and surface tension, yet not fully resolved so far. EXPERIMENTS: To elucidate the influence of the bulk shear mode on the recorded correlation functions related to surface fluctuations with an oscillatory behavior, different evaluation procedures are compared. A new evaluation approach is suggested, which makes use of the entire signal information and represents the contribution of the bulk shear mode to the signal in a convenient and physically meaningful way. This allows to unambiguously access the dynamics of the probed surface fluctuations, i.e. their mean lifetime and frequency as well as their response to the rotational flow in the bulk of the fluid. FINDINGS: By applying the evaluation approach to SLS signals for eight different vapor-liquid systems corresponding to reduced capillary numbers between about 0.4 and 15, it is demonstrated that the developed strategy allows for an accurate determination of viscosity and surface tension. This strategy facilitates the thermophysical property research on fluids by SLS experiments performed close to the critical damping.


Subject(s)
Viscosity , Surface Tension
6.
J Colloid Interface Sci ; 623: 595-606, 2022 Oct.
Article in English | MEDLINE | ID: mdl-35598487

ABSTRACT

HYPOTHESIS: The accurate determination of viscosity and interfacial tension by surface light scattering (SLS) represents a challenging task, especially in the range of small wave vectors. Here, measurements are subjected to line-broadening effects, which are often not adequately described by empirical fitting routines in literature. EXPERIMENTS: For tackling this limitation, a novel evaluation strategy relying on a Monte-Carlo-based optimization is suggested in the present study. Without making prior assumptions about the underlying distribution of wave vectors, the method allows to decompose the measured SLS signal into a superposition of individual contributions represented by damped oscillations. The resulting amplitude distribution for damping and frequency is used to estimate the central wave vector, all of which is required to solve the dispersion relation for hydrodynamic surface fluctuations in its exact form. FINDINGS: By applying the evaluation strategy to SLS signals recorded in reflection direction for the reference fluid toluene, it is demonstrated that the presented concept provides a route towards an accurate determination of viscosity and surface tension in the range of small wave vectors. Hence, the strategy is considered to extend the application range of SLS in connection with opaque and non-transparent fluids for which small wave vectors often need to be probed experimentally.


Subject(s)
Hydrodynamics , Monte Carlo Method , Surface Tension , Viscosity
7.
J Phys Chem B ; 125(19): 5100-5113, 2021 05 20.
Article in English | MEDLINE | ID: mdl-33960781

ABSTRACT

Dynamic light scattering (DLS) experiments and equilibrium molecular dynamics (EMD) simulations were performed in the saturated liquid phase of the binary mixture of 1-hexyl-3-methylimidazolium bis(trifluormethylsulfonyl)imide ([HMIM][NTf2]) and carbon dioxide (CO2) to access the Fick diffusion coefficient (D11). The investigations were performed within or close to saturation conditions at temperatures between (298.15 and 348.15) K and CO2 mole fractions (xCO2) up to 0.81. The DLS experiments were combined with polarization-difference Raman spectroscopy (PDRS) to simultaneously access the composition of the liquid phase. For the first time in an electrolyte-based system, D11 was directly calculated from EMD simulations by accessing the Maxwell-Stefan (MS) diffusion coefficient and the thermodynamic factor. Agreement within combined uncertainties was found between D11 from DLS and EMD simulations for CO2 mole fractions up to 0.5. In general, an increasing D11 with increasing xCO2 could be observed, with a local maximum present at a CO2 mole fraction of about 0.75. The local maximum could be explained by an increasing MS diffusion coefficient with increasing xCO2 over the entire studied composition range and a decreasing thermodynamic factor at xCO2 above 0.7. Finally, PDRS and EMD simulations were combined to investigate the influence of the fluid structure on the diffusive process.

8.
Langmuir ; 26(8): 5971-5, 2010 Apr 20.
Article in English | MEDLINE | ID: mdl-20345184

ABSTRACT

The present work provides new information on the characteristics of ion implanted metallic surfaces responsible for the adjustment of stable dropwise condensation (DWC) of steam. The results are based on condensation experiments and surface analyses via contact angle (CA) and surface free energy (SFE) measurements as well as scanning electron microscopy (SEM). For studying possible influences of the base material and the implanted ion species, commercially pure titanium grade 1, aluminum alloy Al 6951, and stainless steel AISI 321 were treated with N(+), C(+), O(+), or Ar(+) using ion beam implantation technology. The studies suggest that chemically inhomogeneous surfaces are instrumental in inducing DWC. As this inhomogeneity is apparently caused by particulate precipitates bonded to the metal surface, the resulting nanoscale surface roughness may also influence the condensation form. On such surfaces nucleation mechanisms seem to be capable of maintaining DWC even when CA and SFE measurements indicate increased wettability. The precipitates are probably formed due to the supersaturation of ion implanted metal surfaces with doping elements. For high-alloyed materials like AISI 321 or Hastelloy C-276, oxidation stimulated by the condensation process obviously tends to produce similar surfaces suitable for DWC.

9.
J Phys Chem B ; 124(12): 2482-2494, 2020 Mar 26.
Article in English | MEDLINE | ID: mdl-32105484

ABSTRACT

This work contributes to an improved understanding of the fluid-phase behavior and diffusion processes in mixtures of 1-hexanol and carbon dioxide (CO2) at temperatures around the upper critical end point (UCEP) of the system. Raman spectroscopy and dynamic light scattering were used to determine the composition at saturation conditions as well as Fick and thermal diffusivities. An acceleration of the Fick diffusive process up to CO2 mole fractions of about 0.2 was found, followed by a strong slowing-down approaching vapor-liquid-liquid equilibrium or critical conditions. The acceleration of the Fick diffusive process vanished at temperatures much higher than the UCEP. Experimental Fick diffusivity data were compared with predictions from equilibrium molecular dynamics simulations and excess Gibbs energy calculations using interaction parameters from the literature. Both theoretical methods were not able to predict that the thermodynamic factor is equal to zero at the spinodal composition, stressing the need for new methodologies under such conditions. Thus, new sets of temperature-dependent interaction parameters were developed for the nonrandom two-liquid model, which improve the prediction of the Fick diffusion coefficient considerably. The link between the Fick diffusion coefficient and the nonrandomness of the liquid phases is also discussed.

10.
J Phys Chem B ; 124(20): 4146-4163, 2020 May 21.
Article in English | MEDLINE | ID: mdl-32315527

ABSTRACT

This work contributes to the characterization of long linear and branched alkanes and alcohols via the determination of their thermophysical properties up to temperatures of 573.15 K. For this, experimental techniques including surface light scattering (SLS) and molecular dynamics (MD) simulations were used under equilibrium conditions to analyze the influences of chain length, branching, and hydroxylation on liquid density, liquid viscosity, and surface tension. For probing these effects, 12 pure model systems given by the linear alkanes n-dodecane, n-hexadecane, n-octacosane, n-triacontane, and n-tetracontane, the linear alcohols 1-dodecanol, 1-hexadecanol, and 1,12-dodecanediol, the branched alkanes 2,2,4,4,6,8,8-heptamethylnonane (HMN) and 2,6,10,15,19,23-hexamethyltetracosane (squalane), and the branched alcohols 2-butyl-1-octanol and 2-hexyl-1-decanol were investigated at or close to saturation conditions at temperatures between 298.15 and 573.15 K. Based on the experimental results for the liquid densities, liquid viscosities, and surface tensions with average expanded uncertainties (k = 2) of 0.061, 2.1, and 2.6%, respectively, the performance of the three commonly employed force fields (FFs) TraPPE, MARTINI, and L-OPLS was assessed in MD simulations. To improve the simulation results for the best-performing all-atom L-OPLS FF at larger temperatures, a modified version was suggested. This incorporates a temperature dependence for the energy parameters of the Lennard-Jones potential obtained by calibrating only against the experimental liquid density data of n-dodecane. By transferring this approach to all other systems studied, the modified L-OPLS FF shows now a distinctly better representation of the equilibrium and transport properties of the long alkanes and alcohols, especially at high temperatures.

11.
J Colloid Interface Sci ; 538: 671-681, 2019 Mar 07.
Article in English | MEDLINE | ID: mdl-30594112

ABSTRACT

Multiphase systems are relevant in many fields of process engineering. For process and product design in connection with multiphase systems, knowledge on the thermophysical properties of the individual phases such as viscosity and on the interfacial tension between these is required but often lacking in literature. In the present study, the applicability of surface light scattering (SLS) for the simultaneous measurement of interfacial tensions and viscosities in multiphase systems in macroscopic thermodynamic equilibrium is demonstrated. For two model systems consisting of n-decane and methanol as well as n-dodecane and methanol forming a vapor-liquid-liquid equilibrium at atmospheric pressure, surface fluctuations which show an oscillatory behavior at the vapor-liquid and liquid-liquid interface could be associated with hydrodynamic modes. From an exact theoretical description of the dynamics of the surface fluctuations, absolute data for the dynamic viscosities of the two liquid phases as well as the vapor-liquid and liquid-liquid interfacial tensions could be determined at temperatures between (333 and 358) K with total measurement uncertainties (k = 2) down to about 2%. For both systems studied at temperatures close to the upper critical solution temperature, the viscosities of the two liquid phases approach each other and the liquid-liquid interfacial tension tends to zero.

12.
J Phys Chem B ; 123(44): 9491-9502, 2019 Nov 07.
Article in English | MEDLINE | ID: mdl-31592668

ABSTRACT

Polarized dynamic light scattering (DLS) gives access to orientation-averaged translational and rotational diffusion coefficients of anisotropic particles dispersed in fluids in a single experiment. As the combination of both diffusivities contains information on the morphology of the particles, their simultaneous and accurate measurement for the same sample and thermodynamic state is beneficial for particle characterization. For nontransparent model suspensions of gold nanorods in water and water-glycerol mixtures, a scattering geometry in reflection direction was realized, which minimizes multiple scattering and allows using low laser powers to avoid laser heating. Furthermore, a heterodyne detection scheme was guaranteed by superimposing much stronger reference light to the scattered light. This ensures an unambiguous data evaluation and reduces the uncertainties for the rotational and the translational diffusivity, where the latter is accessible with smaller uncertainty. For the water-based suspensions, both diffusivities agree well with the stick hydrodynamic theory for rods and show an Andrade-type behavior in the studied temperature range from 271 to 323 K. The measured results for both diffusivities, particularly for the rotational diffusivity, indicate a breakdown of the stick boundary conditions for dynamic viscosities larger than 4 mPa·s.

13.
J Phys Chem B ; 123(41): 8777-8790, 2019 Oct 17.
Article in English | MEDLINE | ID: mdl-31536354

ABSTRACT

The influence of the strength of intermolecular interactions on mass diffusive processes remains poorly understood for mixtures of associative liquids with dissolved gases. For contributing to a fundamental understanding of the interplay between liquid structures and mass diffusivities in such systems, dynamic light scattering, Raman spectroscopy, and molecular dynamics simulations were used in this work. As model systems, binary mixtures consisting of the gases hydrogen, helium, nitrogen, carbon monoxide, or carbon dioxide dissolved in ethanol, 1-hexanol, or 1-decanol were selected. Experiments and simulations were performed at macroscopic thermodynamic equilibrium close to infinite dilution of solute for temperatures between 303 and 423 K. The Fick diffusion coefficients and self-diffusivities of the gas solutes increase with increasing temperature, decreasing alkyl chain length of the 1-alcohols, and decreasing molar mass of the solutes except for helium and hydrogen showing the opposite behavior. The analysis of the liquid structure of the mixtures showed that the fraction of hydrogen-bonded alcohol molecules decreases with increasing alkyl chain length and temperature. From the obtained structure-property relationships, a new correlation was developed to predict mass diffusivities in binary mixtures consisting of n-alkanes or 1-alcohols with dissolved gases close to infinite dilution within 10% on average.

14.
J Phys Chem B ; 112(39): 12420-30, 2008 Oct 02.
Article in English | MEDLINE | ID: mdl-18767789

ABSTRACT

The density, refractive index, interfacial tension, and viscosity of ionic liquids (ILs) [EMIM][EtSO 4] (1-ethyl-3-methylimidazolium ethylsulfate), [EMIM][NTf 2] (1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide), [EMIM][N(CN) 2] (1-ethyl-3-methylimidazolium dicyanimide), and [OMA][NTf 2] (trioctylmethylammonium bis(trifluoromethylsulfonyl)imide) were studied in dependence on temperature at atmospheric pressure both by conventional techniques and by surface light scattering (SLS). A vibrating tube densimeter was used for the measurement of density at temperatures from (273.15 to 363.15) K and the results have an expanded uncertainty ( k = 2) of +/-0.02%. Using an Abbe refractometer, the refractive index was measured for temperatures between (283.15 and 313.15) K with an expanded uncertainty ( k = 2) of about +/-0.0005. The interfacial tension was obtained from the pendant drop technique at a temperature of 293.15 K with an expanded uncertainty ( k = 2) of +/-1%. For higher and lower temperatures, the interfacial tension was estimated by an adequate prediction scheme based on the datum at 293.15 K and the temperature dependence of density. For the ILs studied within this work, at a first order approximation, the quantity directly accessible by the SLS technique was the ratio of surface tension to dynamic viscosity. By combining the experimental results of the SLS technique with density and interfacial tension from conventional techniques, the dynamic viscosity could be obtained for temperatures between (273.15 and 333.15) K with an estimated expanded uncertainty ( k = 2) of less than +/-3%. The measured density, refractive index, and viscosity are represented by interpolating expressions with differences between the experimental and calculated values that are comparable with but always smaller than the expanded uncertainties ( k = 2). Besides a comparison with the literature, the influence of structural variations on the thermophysical properties of the ILs is discussed in detail. The viscosities mostly agree with values reported in the literature within the combined estimated expanded uncertainties ( k = 2) of the measurements while our density and interfacial tension data differ by more than +/-1% and +/-5%.

15.
J Phys Chem B ; 122(12): 3163-3175, 2018 03 29.
Article in English | MEDLINE | ID: mdl-29485876

ABSTRACT

In the present study, dynamic light scattering (DLS) experiments and molecular dynamics (MD) simulations were used for the investigation of the molecular diffusion in binary mixtures of liquids with dissolved gases at macroscopic thermodynamic equilibrium. Model systems based on the n-alkane n-hexane or n-decane with dissolved hydrogen, helium, nitrogen, or carbon monoxide were studied at temperatures between 303 and 423 K and at gas mole fractions below 0.06. With DLS, the relaxation behavior of microscopic equilibrium fluctuations in concentration and temperature is analyzed to determine simultaneously mutual and thermal diffusivity in an absolute way. The present measurements document that even for mole gas fractions of 0.007 and Lewis numbers close to 1, reliable mutual diffusivities with an average expanded uncertainty ( k = 2) of 13% can be obtained. By use of suitable molecular models for the mixture components, the self-diffusion coefficient of the gases was determined by MD simulations with an averaged expanded uncertainty ( k = 2) of 7%. The DLS experiments showed that the thermal diffusivity of the studied systems is not affected by the dissolved gas and agrees with the reference data for the pure n-alkanes. In agreement with theory, mutual diffusivities and self-diffusivities were found to be equal mostly within combined uncertainties at conditions approaching infinite dilution of the gas. Our DLS and MD results, representing the first available data for the present systems, reveal distinctly larger mass diffusivities for mixtures containing hydrogen or helium compared to mixtures containing nitrogen or carbon monoxide. On the basis of the broad range of mass diffusivities of the studied gas-liquid systems covering about 2 orders of magnitude from about 10-9 to 10-7 m2·s-1, effects of the solvent and solute properties on the temperature-dependent mass diffusivities are discussed. This contributed to the development of a simple semiempirical correlation for the mass diffusivity of the studied gases dissolved in n-alkanes of varying chain length at infinite dilution as a function of temperature. The generalized expression requiring only information on the kinematic viscosity and molar mass of the pure solvent as well as the molar mass and acentric factor of the solute represents the database from this work and further literature with an absolute average deviation of about 11%.

16.
J Phys Chem B ; 122(28): 7122-7133, 2018 07 19.
Article in English | MEDLINE | ID: mdl-29889520

ABSTRACT

This study contributes to a fundamental understanding of how the liquid structure in a model system consisting of weakly associative n-hexane ( n-C6H14) and carbon dioxide (CO2) influences the Fickian diffusion process. For this, the benefits of light scattering experiments and molecular dynamics (MD) simulations at macroscopic thermodynamic equilibrium were combined synergistically. Our reference Fickian diffusivities measured by dynamic light scattering (DLS) revealed an unusual trend with increasing CO2 mole fractions up to about 70 mol %, which agrees with our simulation results. The molecular impacts on the Fickian diffusion were analyzed by MD simulations, where kinetic contributions related to the Maxwell-Stefan (MS) diffusivity and structural contributions quantified by the thermodynamic factor were studied separately. Both the MS diffusivity and the thermodynamic factor indicate the deceleration of Fickian diffusion compared to an ideal mixture behavior. Computed radial distribution functions as well as a significant blue-shift of the CH stretching modes of n-C6H14 identified by Raman spectroscopy show that the slowing down of the diffusion is caused by a structural organization in the binary mixtures over a broad concentration range in the form of self-associated n-C6H14 and CO2 domains. These networks start to form close to the infinite dilution limits and seem to have their largest extent at a solute-solvent transition point at about 70 mol % CO2. The current results not only improve the general understanding of mass diffusion in liquids but also serve to develop sound prediction models for Fick diffusivities.

17.
J Phys Chem B ; 111(44): 12817-22, 2007 Nov 08.
Article in English | MEDLINE | ID: mdl-17939709

ABSTRACT

Within this work, viscosity and interfacial tension of selected ionic liquid cosolvent mixtures, [EMIM][EtOSO3] (1-ethyl-3-methyl-immidazolium ethyl sulfate) with water and ethanol, were studied as a function of composition by surface light scattering (SLS) and the pendant drop method in a consistent manner, allowing a close insight into the nature of interactions. Here, we show that the viscosity behavior clearly reflects the bulk structure of the ionic liquid cosolvent mixtures and correlates to the fluid structure at the phase boundary. In contrast to former work, we found the viscosity of ionic liquid [EMIM][EtOSO3] to be decreasing the stronger by small amounts of the cosolvents and the lower their dielectric constant. Furthermore, two distinct trends for the dependence of the viscosity on the cosolvent concentration were resolved. These were assigned to ion-dipole interactions dominating in the salt-rich region and to dipole-dipole interactions in the diluted one. A crossover between both regions is reflected by the interfacial tension data, where it seems that up to a "critical" concentration almost no cosolvent is present at the phase boundary.

18.
J Phys Chem B ; 121(16): 4145-4157, 2017 04 27.
Article in English | MEDLINE | ID: mdl-28388084

ABSTRACT

Thermophysical properties of low-viscosity ionic liquids (ILs) based on the tetracyanoborate ([B(CN)4]-) anion carrying a homologous series of 1-alkyl-3-methylimidazolium ([AMIM]+) cations [EMIM]+ (ethyl), [BMIM]+ (butyl), [HMIM]+ (hexyl), [OMIM]+ (octyl), and [DMIM]+ (decyl) were investigated by experimental methods and molecular dynamics (MD) simulations at atmospheric pressure and various temperatures. Spectroscopic methods based on nuclear magnetic resonance and surface light scattering were applied to measure the ion self-diffusion coefficients and dynamic viscosity, respectively. In terms of MD simulations, a nonpolarizable molecular model for [EMIM][B(CN)4] developed by optimization to experimental data was transferred to the other homologous ILs. For the appropriate description of the inter- and intramolecular interactions, precise and approximate force fields (FFs) were tested regarding their transferability within the homologous IL series, aiming at reducing the computational effort in molecular simulations. It is shown that at comparable simulated and experimental densities, the calculated and measured data for viscosity and self-diffusion coefficients of the ILs agree well mostly within combined uncertainties, but deviate stronger for longer-chained ILs using an overly coarse FF model. For the [B(CN)4]--based ILs studied, a comparison with literature data, the influence of varying alkyl chain length in the cation on their structural and thermophysical properties, and a correlation between self-diffusivity and viscosity are discussed.

19.
J Phys Chem B ; 121(47): 10665-10673, 2017 11 30.
Article in English | MEDLINE | ID: mdl-29091450

ABSTRACT

In this study, we demonstrate the ability of polarization-difference Raman spectroscopy (PDRS) to detect dissolved free water molecules in a n-octacosane (n-C28H58) liquid-rich phase, and thus to determine its solubility, at temperatures and pressures relevant to the Fischer-Tropsch synthesis. Our results for the pure alkane reveal thermal decomposition above a temperature of 500 K as well as an increase of gauche conformers of the alkane chains with an increase in temperature. For binary homogeneous mixtures, raw spectra obtained from two different polarization scattering geometries did not show a relevant signal in the OH stretching frequency range. In contrast, isotropic spectra obtained from the PDRS technique reveal a narrow and tiny peak associated with the dangling OH bonds. Over the complete range of temperatures and pressures, no signature of hydrogen-bonded water molecules was observed in the isotropic Raman scattering intensities. A thorough investigation covering a large range of temperatures and pressures using PDRS signals showed that the higher the fraction of gauche conformers of hydrocarbon, the higher the solubility of water. The proportion of gauche and trans conformers was found to be water-concentration-independent, and the intensity of the OH-dangling peak increased linearly with increasing the vapor partial pressure of water. Therefore, we established a relation between a relevant intensity ratio and the concentration of water obtained from SAFT calculations. Contrary to the results from relevant literature, the calibration factor was found to be temperature-independent between 424 and 572 K. The isotropic Raman scattering intensities are corrected in order to provide a better representation of the vibrational density of states. The influence of correction of the isotropic scattering intensities on the solubility measurements as well as on the analysis of the molecular arrangement is discussed.

20.
J Phys Chem B ; 121(48): 10950-10956, 2017 12 07.
Article in English | MEDLINE | ID: mdl-29125767

ABSTRACT

For the first time, we demonstrate that it is possible to simultaneously analyze microscopic fluctuations at the surface and in the bulk of a binary liquid mixture by dynamic light scattering in macroscopic thermodynamic equilibrium. For a model system containing n-octacosane and ethanol, three individual signals distinguishable in the time-resolved analysis of the scattered light intensity appear on different time scales. One oscillatory signal from surface fluctuations at the vapor-liquid interface in the short-time range and two exponential Rayleigh signals from fluctuations in temperature and concentration in the bulk of fluid in the long-time range could be associated with hydrodynamic modes. This microscopic information allows for a simultaneous determination of the macroscopic properties interfacial tension, kinematic viscosity, thermal diffusivity, and mutual diffusivity within a single experimental run. The presented approach represents a worthwhile strategy, for example, in the context of sensor development for an effective multiproperty determination of fluid systems.

SELECTION OF CITATIONS
SEARCH DETAIL