Escape and functional alterations of microbial aerosol particles containing Pseudomonas sp. during wastewater treatment.

Wastewater treatment plants (WWTP) are considered sources of bioaerosols emission that negatively affects the surrounding atmosphere. This study focused on Pseudomonas sp. Emissions in bioaerosols from a WWTP that adopts the A2O treatment process, and their inactivation through ultraviolet (UV) radiation. High-throughput sequencing was used to assay the microbial population, and functional composition profiles were predicted using 16 S rRNA sequencing data with PICRUSt2. Recorded emission levels of airborne bacteria and Pseudomonas sp. In WWTP were 130 ± 83-6113 ± 3015 CFU/m3 and 0-6431 ± 1945 CFU/m3, respectively. Bioaerosol emissions presented site-related and temporal variation. Over 80% of Pseudomonas sp. Were attached to coarse particles with sizes over 2.1 µm. Bioaerosol concentration and particle-size distribution in the air were closely related to ambient temperature, relative humidity, light intensity, and wind speed. Exposure to 45.67 µW/cm3 UV radiation led to a significant decline in bioaerosol concentrations in the air, and reduction rate reached 89.16% and 95.77% for airborne bacteria and Pseudomonas sp., respectively. The results suggested that UV radiation can be an effective method in reducing bioaerosols. Compared with other bacteria, Pseudomonas stutzeri and Bacillus sp. Are more resistant to UV radiation. The abundance of antibiotic resistance genes noticeably receded when exposed to UV irradiation. The relative abundance of cationic antimicrobial peptide resistance, categorized under human diseases in KEGG (level 3), significantly decreased in Pseudomonas sp. After 120 min of UV irradiation. This study provides a novel insight into the control of bioaerosol emissions carrying pathogenic bacteria.

Distribution characteristics and potential risks of bacterial aerosol in waste transfer station.

The waste transfer station (WTS) is an important link in the transfer of municipal solid waste (MSW) between the community and disposal terminals. While WTSs facilitate waste collection in communities, odorous gases and bioaerosols can escape from them, thereby negatively affecting their surroundings. In this study, the concentration, particle size distribution, pathogen population, and health risks of bioaerosols were analyzed at different locations in a transfer station. The results showed that the highest viable bacterial aerosol concentration was 10,353 ± 3701 CFU/m3, which was at 5 m from the disposal site. Fifty-three bacterial species, including pathogens, were detected. Of these, 39 were human pathogenic bacteria directly originating from the WTS. Furthermore, health risk assessments indicated unacceptable levels of non-carcinogenic risk for operational workers caused by bacterial aerosols of the WTS work area. In addition, bacterial aerosols may pose a severe health risk to children within a 15 m area of the WTS. The results of this study provide a scientific basis to control and reduce the risk associated with bioaerosol exposure in solid WTSs.

Emission behavior and impact assessment of gaseous volatile compounds in two typical rural domestic waste landfills.

Landfill sites are sources of gaseous volatile compounds. The dumping area (LDA) and leachate storage pool (LSP) of two typical rural domestic waste landfill sites in north China (NLF) and southwest China (SLF) were investigated. We found that 45, 46, 61 and 68 volatile organic compounds (VOC) were present in the air of NLF-LDA, NLF-LSP, SLF-LDA, and SLF-LSP, respectively. And there were 27, 29, 35 and 37 kinds of odorous compounds being detected. Oxygenated compounds (>48.88%), chlorinated compounds (>6.85%), and aromatics (>5.46%), such as organic acid, 1-chlorobutane, and benzene, were the most abundant compounds in both landfills. The SLF-LDA had the highest olfactory effect, with a corresponding total odor activity value of 29,635.39. The ozone-formation potential analysis showed that VOCs emitted from SLF landfills had significantly higher potential for ozone formation than those from NLF landfills, with ozone generation potentials of 166.02, 225.86, 2511.82, and 1615.99 mg/m3 for the NLF-LDA, NLF-LSP, SLF-LDA, and SLF-LSP, respectively. Higher chronic toxicity and cancer risk of VOCs were found in the SLF according to method of Risk Assessment Information System. Based on the sensitivity analysis by the Monte Carlo method, concentrations of benzene, propylene oxide, propylene, trichloroethylene, and N-nitrosodiethylamine, along with exposure duration, daily exposure time, and annual exposure frequency, significantly impacted the risk levels. We provide a scientific basis, which reflects the need for controlling and reducing gaseous pollutants from landfills, particularly rural residential landfills, which may improve rural sanitation.

Effect and environmental behaviour of microplastics in soil.

Soil microplastic pollution is currently a worldwide concern. Microplastics are organic pollutants that are abundant in the natural environment, are persistent and difficult to degrade and may endanger human health while harming the environment. This article offers a bibliometric analysis of the environmental behaviour of microplastics in soils, as well as a thorough statistical analysis of research goals and trends in this field. We conducted a thorough search of all relevant literature from 2012 to 2022 in the Web of Science core database. The data analysis shows that, starting in 2012, there has been an upward trend in the number of articles about soil microplastic pollution. It can also be seen that China is relatively ahead of the curve in this area of research, followed by the United Kingdom and the United States. This article also systematically describes the research hotspots in this field. The results show that the current research on soil microplastics is mainly focused on their identification, enrichment and toxicity, whereas studies on the migration and transformation of soil microplastics and the mechanism of interaction with other pollutants are still lacking. Our results provide ideas and prospects for future research in this field.

Dispersion, olfactory effect, and health risks of VOCs and odors in a rural domestic waste transfer station.

The impact of odorous gases emitted from refuse transfer stations has always been a concern raised by the surrounding residents. The emitted volatile organic compounds (VOCs) and odors were investigated in a rural solid waste transfer station (RSWTS) located in Southwest China. A total of 70 VOCs were identified and quantified. The total VOCs (TVOCs) concentrations varied from 848.38 to 31193.24 µg/m3. Inorganic odor and greenhouse gases concentrations ranged from 39.11 to 470.14 µg/m3 and 1.03-525.42 µg/m3, respectively. Oxygenated compounds contributed the most (58.25%) to the VOCs. Among the oxygenated compounds, ketones, esters, and ethers were the dominant categories, accounting for 67.5%, 12.70%, and 11.85%, respectively. The key odorants included propionaldehyde, hexanaldehyde, propionic acid, acetaldehyde, and disopropyl ether. N-nitrosodiethylamine, acrylonitrile, and 1,3-Butadiene were the three main carcinogens that pose considerable risk to human health. Allyl chloride was the most non-carcinogenic pathogen among the VOCs detected in RSWTS. With diffusion in the downwind direction, the concentration of VOCs decreased gradually, and their risks weakened accordingly. At the sampling site of RSWTS-10, located 100 m away from RSWTS, acrylonitrile and 1,3-Butadiene still presented an unacceptable carcinogenic risk to human health. This study provides new data for assessing the emission characteristics, olfactory effects, and health risks of trace VOCs, especially those released from RSWTS.

Effects of hydrodynamic shear stress on sludge properties, N2O generation, and microbial community structure during activated sludge process.

Sludge properties are critical to the treatment performance and potentially correlate with nitrous oxide (N2O) generation during activated sludge processes. The hydrodynamic shear stress induced by aeration has a significant influence on sludge properties and is inevitable for wastewater treatment plants (WWTPs). In this study, the effects of aerobic induced hydrodynamic shear stress on sludge properties, N2O generation, and microbial community structure were investigated using three parallel sequencing batch reactors (SBRs) with identical dissolved oxygen (DO) concentrations. Results showed that with a shear stress increase from 1.5 × 10-2 N/m2 to 5.0 × 10-2 N/m2, the COD and NH4+-N removal rates were enhanced from 89.4% to 94.0% and from 93.9% to 98.0%, respectively, while the TN removal rate decreased from 66.0% to 56.5%. Settleability of the activated sludge flocs (ASFs) also increased with the enhancement of shear stress, due to variation in sludge properties including particle size, regularity, compactibility, and EPS (extracellular polymeric substances) composition. The increase in shear stress promoted oxygen diffusion within the ASFs and mitigated NO2--N accumulation, leading to a decrease in the N2O-N conversion rate from (4.8 ± 0.3)% to (2.2 ± 0.6)% (based on TN removal). Microbial analysis results showed that the functional bacteria involved in the biological nitrogen removal was closely related with shear stress. The increase in shear stress favored the enrichment of nitrite oxidizing bacteria (NOB) while suppressed the accumulation of ammonia-oxidizing bacteria (AOB) and denitrifying bacteria (DNB).

Bioaerosols emission and exposure risk of a wastewater treatment plant with A2O treatment process.

The characteristics of bioaerosol emissions from wastewater treatment plants (WWTPs) have attracted extensive attention. The anaerobic-anoxic-oxic (A2O) process, which uses the activated sludge approach to wastewater treatment, is the most widely used process in WWTPs. Concentration, size distribution, population, and exposure risk from bacteria and fungi in bioaerosols of WWTPs using the A2O process were studied in this work. The results showed that the maximum concentration of airborne bacteria (1.00 × 104 Colony Forming Units per cubic meter (CFU m-3)) and fungi (1.44 ×104 CFU m-3) occurred from the facility's aerobic tank, in summer. As one of the main factors affecting bioaerosol exposure risk, particle size distribution was related to season. The study found that particles larger than 3.3 µm in diameter were detected mainly in spring and summer, while particles less than 3.3 µm were detected mainly in autumn and winter, whether bacterial aerosol or fungal aerosol. In addition, pathogenic bacteria were observed in bioaerosols from WWTPs, with 18 of the 65 species of bacteria detected found to be potentially or opportunistically pathogenic, such as Chryseobacterium, Stenotrophomonas, Alcaligenes, Micrococcus, Pantoea, Enterobacter and Escherichia-Shigella. The presence of these pathogens further increased the exposure risk from bioaerosols. The results of an inhalation risk assessment for airborne bacteria and fungi indicated that potential adverse health risks for adults mainly occurred in spring, summer, and autumn. On this basis, it was concluded that WWTP operators should set up effective bioaerosol controls as soon as possible to protect the health of workers, and of residents near the plant.

Characteristics and exposure risks of potential pathogens and toxic metal(loid)s in aerosols from wastewater treatment plants.

Aerosols from wastewater treatment plants (WWTPs) are considered to be potentially hazardous to on-site employees and surrounding residents. However, their harmful components and their effects remain poorly understood. In this study, the characteristics, responsible factors, sources and exposure risks of potential pathogens and toxic metal(loid)s in aerosols from four WWTPs were investigated. There were 21 potential pathogens and 15 toxic metal(loid)s detected in the aerosols. Arcobacter and Fe were the dominant taxa responsible for the dissimilarity of the potential pathogen population and toxic metal(loid) composition between the aerosols and the wastewater/sludge, respectively. Both meteorological factors and sources affected pathogen and toxic metal(loid) composition. The potential pathogens and toxic metal(loid)s in indoor aerosols mainly originated from wastewater/sludge, while those in outdoor aerosols originated from wastewater/sludge and ambient air. The highest respirable fraction (<3.30 µm) concentrations and proportions were detected at the aeration units. Non-carcinogenic and carcinogenic risks of toxic metal(loid)s for both adults and children were found within and/or around WWTPs, and non-carcinogenic risks of bacteria for children were found at downwind, suggesting the need for active safeguard procedures, such as that employees wear masks and work clothes, covering the main emission sites, and collecting and destroying of aerosols.

Effects of tetrakis (hydroxymethyl) phosphonium sulfate pretreatment on characteristics of sewage sludge.

Recently, tetrakis(hydroxymethyl)phosphonium sulfate (THPS) was found to play an important role in the sludge pretreatment process. However, the effects of THPS pretreatment on the characteristics of sewage sludge are still insufficiently understood. The properties of sludge after pretreatment with different concentrations of THPS were investigated in this study. The results showed that pH, dewatering ability, and particle size of sludge decreased with increase in THPS concentration. The volatile suspended solids (VSS) and total suspended solids (TSS) of sludge also decreased slightly with increase in THPS concentration. The specific oxygen uptake rate (SOUR) results suggested that lower THPS concentrations (≤1.87 mg/g VSS) enhanced the activity of sludge, but higher concentrations (≥1.87 mg/g VSS) inhibited it. Gram-negative bacteria with peritrichous flagellation (such as Pseudomonas, Escherichia, and Faecalibacterium) were extremely sensitive to THPS. The decrease in specific most probable numbers (MPNs) of pathogens (total coliforms and Escherichia coli) with the increase in THPS concentration also proved the sterilization ability of THPS in the sludge pretreatment process. Pretreatment of sludge with concentrations of THPS higher than 37.41 mg/g VSS would meet the pathogen requirements for land application of Class A biosolids.

Intestinal bacteria in bioaerosols and factors affecting their survival in two oxidation ditch process municipal wastewater treatment plants located in different regions.

Samples from two oxidation ditch process municipal wastewater treatment plants (MWTPs) (HJK and GXQ) in two regions of China were analysed for bacteria, particles, total organic carbon, and water-soluble ions in bioaerosols. Diversity and potential pathogen populations were evaluated by high-throughput sequencing. Bioaerosol sources, factors affecting intestinal bacterial survival, and the relationship between bioaerosols and water were analysed by Source tracker and partial least squares-discriminant, principal component, and canonical correspondence analyses. Culturable bacteria concentrations were 110-846 and 27-579 CFU/m3 at HJK and GXQ, respectively. Intestinal bacteria constituted 6-33% of bacteria. Biochemical reaction tank, sludge dewatering house (SDH), and fine screen samples showed the greatest contribution to bioaerosol contamination. Enterobacter aerogenes was the main intestinal bacteria (> 99.5%) in HJK and detected at each sampling site. Enterobacter aerogenes (98.67% in SDH), Aeromonas sp. (76.3% in biochemical reaction tank), and Acinetobacter baumannii (99.89% in fine screens) were the main intestinal bacteria in GXQ. Total suspended particulate masses in SDH were 229.46 and 141.6 µg/m3 in HJK and GXQ, respectively. Percentages of insoluble compounds in total suspended particulates decreased as height increased. The main soluble ions in bioaerosols were Ca2+, Na+, Cl-, and SO42-, which ranged from 3.8 to 27.55 µg/m3 in the MWTPs. Water was a main source of intestinal bacteria in bioaerosols from the MWTPs. Bioaerosols in HJK but not in GXQ were closely related. Relative humidity and some ions positively influenced intestinal bacteria in bioaerosols, while wind speed and solar illumination had a negative influence.

Characterization and source analysis of indoor/outdoor culturable airborne bacteria in a municipal wastewater treatment plant.

The potential health risks of airborne bacteria emission from a wastewater treatment process have been concerned. However, few studies have investigated the differences in community structure between indoor and outdoor bacteria. In this work, the characterization of airborne bacteria was studied in a municipal wastewater treatment plant in Beijing, China. Two indoor (i.e., fine screen room and sludge dewatering house) and two outdoor (i.e., aeration tank and control site) sampling sites were selected. An Andersen six-stage impactor was used for collecting culturable airborne bacteria in the air, and Illumina MiSeq sequencing was conducted to track the emission source of the culturable airborne bacteria. The results indicate that, compared with the outdoor aeration tank site, the concentrations of culturable airborne bacteria in the indoor fine screen room with poor ventilation were more than ten times higher and the particle size was about twice as large. The community structures of indoor and outdoor culturable airborne bacteria were obviously different. Enterobacteriaceae and opportunistic pathogens were detected in indoor culturable airborne bacteria, with wastewater and sludge dewatering machine identified as the primary sources. Conversely, Enterobacteriaceae and opportunistic pathogens were not detected in outdoor culturable airborne bacteria. Outdoor high wind speed might have resulted in rapid dilution and mixing of culturable airborne bacteria generated from the aeration tank with the ambient air. The results of the present research suggest that covering pollution sources, increasing ventilation rates, and using protective measures for personnel should be implemented to decrease the exposure risk to indoor culturable airborne bacteria.

Sulfur dioxide and o-xylene co-treatment in biofilter: Performance, bacterial populations and bioaerosols emissions.

Sulfur dioxide (SO2) and benzene homologs are frequently present in the off-gas during the process of sewage sludge drying. A laboratory scale biofilter was set up to co-treat SO2 and o-xylene in the present study. SO2 and o-xylene could be removed simultaneously in a single biofilter. Their concentration ratio in the inlet stream influenced the removal efficiencies. It is worth noting that the removal of SO2 could be enhanced when low concentrations of o-xylene were introduced into the biofilter. Pseudomonas sp., Paenibacillus sp., and Bacillus sp. were the main functional bacteria groups in the biofilter. Sulfur-oxidizing bacteria (SOB) and o-xylene-degrading bacteria (XB) thrived in the biofilter and their counts as well as their growth rate increased with the increase in amount of SO2 and o-xylene supplied. The microbial populations differed in counts and species due to the properties and components of the compounds being treated in the biofilter. The presence of mixed substrates enhanced the diversity of the microbial population. During the treatment process, bioaerosols including potentially pathogenic bacteria, e.g., Acinetobacter lwoffii and Aeromonas sp., were emitted from the biofilter. Further investigation is needed to focus on the potential hazards caused by the bioaerosols emitted from waste gas treatment bioreactors.

The response and factors of microbial aerosol emission from the sludge bio-drying process.

Exposure to high levels of microbial contaminants during waste disposal leads to the development of various diseases, including respiratory symptoms and gastrointestinal infections. In this study, the emissions of airborne bacteria and fungi during the process of sludge bio-drying were investigated. The recorded emission levels of airborne bacteria and fungi were 2398 ± 1307 CFU/m3 and 1963 ± 468 CFU/m3, respectively. Viable bacteria were sized between 1.1 and 3.3 µm, while fungal particles were concentrated between 2.1 and 4.7 µm. High-throughput sequencing was used to conduct a microbial population assay, and correlation analysis was performed to estimate the relationship between key factors and bioaerosol emissions. The main bacteria identified were Bacillus sp., Lysinibacillus sp. YS11, unclassified Enterobacteriaceae, Brevundimonas olei, and Achromobacter sp.; the primary types of fungi were Aspergillus ochraceus, Gibberella intricans, Fusarium concentricum, Aspergillus qinqixianii, and Alternaria sp.; and the dominant opportunistic pathogens were Bacillus anthracis and Aspergillus ochraceus. At lower moisture and temperature levels, airborne bacterial concentrations were higher, especially the release of fine particles. In addition, moisture content had a significant impact on the microbial population in bioaerosols. This study provides insights into strategies for controlling bioaerosols in the exhaust gases of the sludge bio-drying process.

Impact of haze on potential pathogens in surface bioaerosol in urban environments.

Air quality considerably affects bioaerosol dynamics within the atmosphere. Frequent haze events, with their associated alterations in bioaerosol composition, may pose potential health risks. This study investigated the microbial diversity, community structure, and factors of PM2.5 within an urban environment. We further examined the impact of haze on potentially pathogenic bacteria in bioaerosols, and analyzed the sources of haze pollution. Key findings revealed that the highest levels of microbial richness and diversity were associated with lightly polluted air conditions. While the overall bacterial community structure remained relatively consistent across different air quality levels, the relative abundance of specific bacterial taxa exhibited variations. Meteorological and environmental conditions, particularly sulfur dioxide, nitrogen dioxide, and carbon monoxide, exerted a greater influence on bacterial diversity and community structure compared to the physicochemical properties of the PM2.5 particles themselves. Notably, haze events were observed to strengthen interactions among airborne pathogens. Stable carbon isotope analysis suggested that coal combustion and automobile exhaust were likely to represent the primary source of haze during winter months. These findings indicate that adoption of clean energy alternatives such as natural gas and electricity, and the use of public transportation, is crucial to mitigate particle and harmful pollutant emissions, thereby protecting public health.

Potential pathogenic microorganisms in rural wastewater treatment process: Succession characteristics, concentration variation, source exploration, and risk assessment.

Pathogenic microorganisms can cause infection, sepsis, and other diseases in humans. Although municipal wastewater plants are important sources and sinks for potential pathogenic microorganisms, data on rural wastewater treatment processes are limited. The proximity of rural wastewater facilities to human settlements and the trend toward wastewater resourcing could pose risks to humans. Here, a typical village in southern China was selected to analyze potential pathogenic microorganisms in wastewater, sewage sludge, and aerosols during the collection, treatment, and discharge of domestic wastewater. The succession characteristics and concentration variations of potential pathogenic microorganisms throughout the wastewater treatment process were identified using high-throughput sequencing and culture methods. Bacteria-associated health risks in facility aerosols were estimated based on average daily dose rates from inhalation and dermal exposure. Lower amounts of pathogenic bacteria and pathogenic fungi were detected in the effluent of the 1-ton treatment scale and the 10-ton treatment scale facilities, compared to those in the influent. Pathogen effluent concentrations were significantly lower than influent concentrations after treatment in rural wastewater facilities. 16 and 29 potential pathogenic bacteria and fungi were detected in aerosols from wastewater treatment facilities, respectively. Furthermore, the potential pathogen concentrations were higher than those in the background air. Aerobic units are the main source of pathogen emissions from aerosols. There were 42 potential pathogenic bacteria and 34 potential pathogenic fungi in the sewage sludge. Biochemical units were the main source of potential pathogens in sewage sludge, and more potential airborne pathogens originated from wastewater. In rural wastewater resourcing processes with greater pollutant exposure, the effluent of rural wastewater treatment facilities (WWTFs), downstream rivers, and facility aerosols, could be important potential sources of microbial risk. Inhalation is the main pathway of human exposure to airborne bacteria. Therefore, more attention should be focused on microbiological risk in rural wastewater treatment processes.

Global diversity of airborne pathogenic bacteria and fungi from wastewater treatment plants.

Wastewater treatment plants (WWTPs) have been recognized as one of the major potential sources of the spread of airborne pathogenic microorganisms under the global pandemic of COVID-19. The differences in research regions, wastewater treatment processes, environmental conditions, and other aspects in the existing case studies have caused some confusion in the understanding of bioaerosol pollution characteristics. In this study, we integrated and analyzed data from field sampling and performed a systematic literature search to determine the abundance of airborne microorganisms in 13 countries and 37 cities across four continents (Asia, Europe, North America, and Africa). We analyzed the concentrations of bioaerosols, the core composition, global diversity, determinants, and potential risks of airborne pathogen communities in WWTPs. Our findings showed that the culturable bioaerosol concentrations of global WWTPs are 102-105 CFU/m3. Three core bacterial pathogens, namely Bacillus, Acinetobacter, and Pseudomonas, as well as two core fungal pathogens, Cladosporium and Aspergillus, were identified in the air across global WWTPs. WWTPs have unique core pathogenic communities and distinct continental divergence. The sources of airborne microorganisms (wastewater) and environmental variables (relative humidity and air contaminants) have impacts on the distribution of airborne pathogens. Potential health risks are associated with the core airborne pathogens in WWTPs. Our study showed the specificity, multifactorial influences, and potential pathogenicity of airborne pathogenic communities in WWTPs. Our findings can improve the understanding of the global diversity and biogeography of airborne pathogens in WWTPs, guiding risk assessment and control strategies for such pathogens. Furthermore, they provide a theoretical basis for safeguarding the health of WWTP workers and ensuring regional ecological security.

Transport and risk of airborne pathogenic microorganisms in the process of decentralized sewage discharge and treatment.

Sewage treatment processes are a critical anthropogenic source of bioaerosols and may present significant health risks to plant workers. Compared with the specialization and scale of urban sewage treatment, many decentralized treatment models are flexible and extensive. These treatment facilities are usually close to residential areas owing to the pipe network layout and other restrictions. Bioaerosols generated by these facilities may present a serious and widespread occupational and non-occupational exposure risk to nearby residents, particularly the elderly and children. An understanding of the characteristics and exposure risks of bioaerosols produced during decentralized sewage treatment is lacking. We compared bioaerosol emission characteristics and potential exposure risks under four decentralized sewage discharge methods and treatment models: small container collection (SCC), open-channel discharge (OCD), single household/combined treatment (SHCT), and centralized treatment (CT) in northwest China. The OCD mode had the highest bioaerosol production, whereas the CT mode had the lowest. The OCD model contained the most pathogenic bacterial species, up to 43 species, including Sphingomonas, Pseudomonas, Cladosporium, and Alternaria. Risk assessments indicated bioaerosol exposure was lower in the models with sewage treatment (SHCT and CT) than in those without (SCC and OCD). Different populations exhibited large variations in potential risks owing to differences in time spent indoors and outdoors. The highest risk was observed in males exposed to the SCC model. This study provides a theoretical basis and theories for the future joint prevention and control of the bioaerosol exposure risk from decentralized sewage treatment.

Assessing genetic structure, diversity of bacterial aerosol from aeration system in an oxidation ditch wastewater treatment plant by culture methods and bio-molecular tools.

Airborne bacteria emissions from oxidation ditch with rotating aeration brushes were investigated in a municipal wastewater treatment plant in Beijing, China. Microbial samples were collected at different distances from the rotating brushes, different heights above the water surface, and different operation state over a 3-month period (April, May, and June) in order to estimate the seasonal variation and site-related distribution characteristics of the microorganisms present. The concentration of bacterial aerosol was analyzed by culture methods, while their dominant species, genetic structure and diversity were assayed using bio-molecular tools. Results showed that total microbial concentrations were highest in June and lowest in April. The mechanical rotation caused remarkable variation in concentration and diversity of culturable airborne bacteria before and after the rotating brushes. The highest concentration was observed near the rotating brushes (931 ± 129-3,952 ± 730 CFU/m(3)), with concentration decreasing as distance and height increased. Bacterial community polymerase chain reaction and denaturing gradient gel electrophoresis indicated that diversity decreased gradually with increasing height above the water surface but remained relatively constant at the same height. All dominant bacteria identified by DNA sequence analysis belonged to Firmicutes. Pathogenic species such as Moraxella nonliquefaciens and Flavobacterium odoratum were isolated from the bioaerosols. Due to the serious health risks involved, exposure of sewage workers to airborne microorganisms caused by brush aerators should be monitored and controlled.

Characterization of the airborne bacteria community at different distances from the rotating brushes in a wastewater treatment plant by 16S rRNA gene clone libraries.

Biological risks of bioaerosols emitted from wastewater treatment processes have attracted wide attention in the recent years. However, the culture-based analysis method has been mostly adopted for detecting the bacterial community in bioaerosols, which may result in the underestimation of total microorganism concentration as not all microorganisms are cultivable. In this study, oligonucleotide fingerprinting of 16S rRNA genes was applied to reveal the composition and structure of the bacterial community in bioaerosols from an Orbal oxidation ditch in a Beijing wastewater treatment plant (WWTP). Bioaerosols were collected at different distances from the aerosol source, rotating brushes, and the sampling height was 1.5 in which is the common respiratory height of a human being. The bacterial communities of bioaerosols were diverse, and the lowest bacterial diversity was found at the sampling site just after the rotating brush rotating brush. A large proportion of bacteria in bioaerosols were affiliated with Proteobacteria and Bacteroidetes. Numerous bacteria present in the bioaerosols also emerged in water, indicating that the bacterial community in the bioaerosols was related to that of the aerosols' sources. The forced aeration of rotating brushes brought about observably distinct bacterial communities between sampling sites situated before and after the rotating brush. Isolation sources of closest relatives in bioaerosols clone libraries were associated with the aqueous environment in the WWTP. Common potential pathogens in bioaerosols as well as those not reported in previous research were also analyzed in this study. Measures should be adopted to reduce the emission of bioaerosols and prevent their exposure to workers.

Dispersion characteristics of bioaerosols during treatment of rural solid waste in northwest China.

In rural China, the release of bioaerosols containing pathogens from solid waste dumps poses a potential health risk to the local population. Here, we sampled bioaerosols from rural solid waste-treatment in four provinces of northwest China to investigate their emission and dispersion characteristics in order to provide a scientific basis for control and risk reduction of bioaerosols released from rural sanitation facilities. The airborne bioaerosol concentrations and particle size distributions were calculated using an Anderson six-stage airborne microbial sampler and counting with its internal Petri dish culture. High-throughput sequencing was used to characterize the microbial composition at different sampling sites and to explore possible influencing factors, while the health risk associated with exposure was estimated based on average daily dose-rate. The highest concentration point values of bacteria and fungi in bioaerosols near the solid waste were 63,617 ± 15,007 and 8044 ± 893 CFU/m³, respectively. Furthermore, the highest concentration point values of Enterobacteriaceae was 502 ± 35 CFU/m³. Most bioaerosols were coarse particles larger than 3.3 µm. Potentially pathogenic genera of winter-indicator species detected in the air were primarily Delftia, Rhodococcus and Aspergillus. The composition of solid waste and environmental conditions are important factors in determining the characteristics of bioaerosols. Local residents are exposed to bioaerosols mainly through inhalation. Children are at a particularly high risk of exposure through both inhalation and skin contact. The results of this study show that bioaerosols in the vicinity of rural solid waste dumps pose a health risk to the surrounding population. More suitable risk assessment criteria for rural areas should be established, and corresponding control and protection measures should be taken from three aspects: generation source and transmission pathway, as well as the recipient.