Valorization of Peanut Skin as Agricultural Waste Using Various Extraction Methods: A Review.

Peanuts (Arachis hypogea) can be made into various products, from oil to butter to roasted snack peanuts and candies, all from the kernels. However, the skin is usually thrown away, used as cheap animal feed, or as one of the ingredients in plant fertilizer due to its little value on the market. For the past ten years, studies have been conducted to determine the full extent of the skin's bioactive substance repertoire and its powerful antioxidant potential. Alternatively, researchers reported that peanut skin could be used and be profitable in a less-intensive extraction technique. Therefore, this review explores the conventional and green extraction of peanut oil, peanut production, peanut physicochemical characteristics, antioxidant activity, and the prospects of valorization of peanut skin. The significance of the valorization of peanut skin is that it contains high antioxidant capacity, catechin, epicatechin resveratrol, and procyanidins, which are also advantageous. It could be exploited in sustainable extraction, notably in the pharmaceutical industries.

Effect of heat treatment on mechanical properties and dimensional accuracy of 3D-Printed black carbon fiber HTPLA.

This present study investigated how heat treatment affects the mechanical properties of 3D-printed black carbon fiber HTPLA by manipulating two parameters: heating temperature and holding time. The mechanical properties of 3D-printed black carbon fiber HTPLA components are crucial for assessing their structural integrity and performance. The shrinkage and dimensional accuracy of the 3D-printed parts were also explored using a vernier caliper. The microstructure of both heat-treated and non-heat-treated HTPLA black carbon fiber 3D-printed parts was examined using scanning electron microscopy. Samples were prepared, printed, heat-treated, and mechanically tested, and their microstructure was observed and recorded. The results showed that heat treatment improved the material's strength, hardness, and crystallinity, leading to better mechanical properties. However, statistical analysis indicates no clear evidence that the two factors, optimum heating temperature and holding time, affect the mechanical properties of heat-treated printed parts. Nonetheless, further study suggests that these factors might be important in optimizing the heat treatment process.

Evaluation of the surface roughness and dimensional accuracy of low-cost 3D-printed parts made of PLA-aluminum.

Fused deposition modeling (FDM) is currently used in several fields, such as architecture, manufacturing, and medical applications. FDM was initially developed to produce and create prototypes, but the expense appears excessive for producing final products. Nevertheless, in this day and age, engineers have developed a low-cost 3D printer. One of the major issues with low-cost 3D printers is the low dimensional accuracy and high tolerances of the printed products. Herein, different printing parameters, i.e., layer thickness, printing speed, and raster angle, need to be investigated to enhance the surface roughness of the parts produced using FDM. Thus, the present study focuses on investigating the performance of the surface finish produced by FDM by manipulating different parameters such as layer thickness, printing speed, and raster angle. Taguchi's method, based on the L9 array for experimental design, was employed to elucidate the response variables. The sample model was developed following ISO standards, utilizing polylactic acid (PLA)-aluminum as the filament material. The analysis of variance results indicated that the layer thickness and raster angle significantly affect the surface roughness of the printed parts, with statistical P-values of 0.016 and 0.039, respectively. This enables an easy selection of the optimal printing parameters to achieve the desired surface roughness. The dimensional accuracy of the fabricated part was also evaluated. Thirteen dimensions of the part features were analyzed, and the results showed that the FDM machine exhibited good accuracy for most of the shapes, with a deviation below 5%.

Stabilizing high-humidity perovskite solar cells with MoS2 hybrid HTL.

The obstacle to the industrialization of perovskite solar cells (PSC) technology lies in their stability. This work rationalizes the PSC design with the employment of 2D-MoS2 as the hybrid hole transport layer (HTL). MoS2 was selected due to its unique optoelectronic and mechanical properties that could enhance hole extraction and thus boost the performance and stability of PSC devices. Five concentrations indicated MoS2 nanosheets were directly deposited onto the perovskite layer via the facile spin coating method. The electrochemical exfoliation and liquid exchange methods were demonstrated to obtain the lateral size of MoS2 nanosheets and further discussed their microscopic and spectroscopic characterizations. Remarkably, the optimum thickness and the excellent device increased the stability of the PSC, allowing it to maintain 45% of its degradation percentage ([Formula: see text]) for 120 h with high relative humidity (RH = 40-50%) in its vicinity. We observed that lithium-ion can intercalate into the layered MoS2 structure and reduce the interfacial resistance of perovskite and the HTL. Most importantly, the 2D-MoS2 mechanism's effect on enabling stable and efficient devices by reducing lithium-ion migration in the HTL is demonstrated in this work to validate the great potential of this hybrid structure in PSC applications.