Excellent Photonic and Mechanical Properties of Macromorphic Fibers Formed by Eu3+-Complex-Anchored, Unzipped, Multiwalled Carbon Nanotubes.

The macromorphic properties of carbon nanotubes perform poorly because of their size limitations: nanosize in diameters and microsize in length. In this work, to realize these dual purposes, we first used an electrochemical method to tear the surface of multiwalled carbon nanotubes (MWCNTs) to anchor photonic Eu3+-complexes there. Through the polar reactive groups endowed by the tearing, the Eu3+-complexes coordinate at the defected structures, obtaining the Eu3+-complex-anchored, unzipped, multiwalled carbon nanotubes (E-uMWCNTs). The controllable surface-breaking retains the MWCNTs' original, excellent mechanical properties. Then, to obtain the macromorphic structure with infinitely long fibers, a wet-spinning process was applied via the binding of a small quantity of polyvinyl alcohol (PVA). Thus, the wet-spun fibers with high contents of E-uMWCNTs (E-uMWCNT-Fs) were produced, in which the E-uMWCNTs took 33.3 wt%, a high ratio in E-uMWCNT-Fs. On the other hand, due to the reinforcing effect of E-uMWCNTs, the highest tensile strength can reach 228.2 MPa for E-uMWCNT-Fs. Meanwhile, the E-uMWCNT-Fs show high-efficiency photoluminescence and excellent media resistance performance due to the embedding effect of PVA on the E-uMWCNTs. Therefore, E-uMWCNT-Fs can exhibit excellent luminescence properties in aqueous solutions at pH 4~12 and in some high-concentration metal-ion solutions. Those distinguished performances promise outstanding innovations of this work.

Heterostructures of Cut Carbon Nanotube-Filled Array of TiO2 Nanotubes for New Module of Photovoltaic Devices.

In this work, a new photovoltaic device was prepared. The device uses titanium (Ti) foil/TiO2 nanotubes as the photoanode and multi-walled carbon nanotubes (MWCNTs) as a photosensitizer. Titanium dioxide nanotube arrays (TiO2-NTs) were prepared by one-step anodic oxidation. Cut-MWCNTs with a length of less than 100 nm were obtained by the mixed-acid oxidation of MWCNTs. The two materials were combined to form a TiO2-NTs@cut-MWCNT heterostructure by electrophoresis. TiO2-NTs@cut-MWCNTs were characterized by field-emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD), which showed that the two materials were effectively combined. We fabricated the heterostructure into a photovoltaic device, showing an enhanced photocurrent response and an efficiency of 0.0138%, and explained this phenomenon by performing UV-vis absorption spectroscopy and electrochemical tests. It is hoped that this work can provide a reference value for the application of carbon nanotubes in photovoltaic devices.

Photoelectrochemical Hydrogen Production System Using Li-Conductive Ceramic Membrane.

Based on the LiLaTiO3 compound, a ceramic membrane for a photoelectrochemical cell was created. The microstructure, phase composition, and conductivity of a semiconductor photoelectrode and a ceramic membrane were studied by using various experimental methods of analysis. A ceramic Li conducting membrane that consisted of Li0.56La0.33TiO3 was investigated in solutions with different pH values. The fundamental possibility of creating a photoelectrochemical cell while using this membrane was shown. It was found that the lithium-conductive membrane effectively works in the photoelectrochemical system for hydrogen evolution and showed a good separating ability. When using a ceramic membrane, the pH in the cathode and anode chambers of the cell was stable during 3 months of testing. The complex impedance method was used to study the conductive ceramic membrane in a cell with separated cathode and anode chambers at different pH values of the electrolyte. The ceramic membrane shows promise for use in photoelectrochemical systems, provided that its resistivity is reduced (due to an increase in area and a decrease in thickness).