Performance improvement of plasmonic sensors using a combination of AC electrokinetic effects for (bio)target capture.

Analytes concentration techniques are being developed with the appealing expectation to boost the performance of biosensors. One promising method lies in the use of electrokinetic forces. We present hereafter a new design for a microstructured plasmonic sensor which is obtained by conventional microfabrication techniques, and which can easily be adapted on a classical surface plasmon resonance imaging (SPRI) system without further significant modification. Dielectrophoretic trapping and electro-osmotic displacement of the targets in the scanned fluid are performed through interdigitated 200 µm wide gold electrodes that also act as the SPR-sensing substrate. We demonstrate the efficiency of our device's collection capabilities for objects of different sizes (200 nm and 1 µm PS beads, as well as 5-10 µm yeast cells). SPRI is relevant for the spatial analysis of the mass accumulation at the electrode surface. We demonstrate that our device overcomes the diffusion limit encountered in classical SPR sensors thanks to rapid collection capabilities (<1 min) and we show a consequent improvement of the detection limit, by a factor >300. This study of an original device combining SPRI and electrokinetic forces paves the way to the development of fully integrated active plasmonic sensors with direct applications in life sciences, electrochemistry, environmental monitoring and agri-food industry.

pH driven addressing of silicon nanowires onto Si3N4/SiO2 micro-patterned surfaces.

pH was used as the main driving parameter for specifically immobilizing silicon nanowires onto Si3N4 microsquares at the surface of a SiO2 substrate. Different pH values of the coating aqueous solution enabled to experimentally distribute nanowires between silicon nitride and silicon dioxide: at pH 3 nanowires were mainly anchored on Si3N4; they were evenly distributed between SiO2 and Si3N4 at pH 2.8; and they were mainly anchored on SiO2 at pH 2. A theoretical model based on DLVO theory and surface protonation/deprotonation equilibria was used to study how, in adequate pH conditions, Si nanowires could be anchored onto specific regions of a patterned Si3N4/SiO2 surface. Instead of using capillary forces, or hydrophilic/hydrophobic contrast between the two types of materials, the specificity of immobilization could rely on surface electric charge contrasts between Si3N4 and SiO2. This simple and generic method could be used for addressing a large diversity of nano-objects onto patterned substrates.

O-Band Emitting InAs Quantum Dots Grown By MOCVD On A 300 mm Ge-Buffered Si (001) Substrate.

The epitaxy of III-V semiconductors on silicon substrates remains challenging because of lattice parameter and material polarity differences. In this work, we report on the Metal Organic Chemical Vapor Deposition (MOCVD) and characterization of InAs/GaAs Quantum Dots (QDs) epitaxially grown on quasi-nominal 300 mm Ge/Si(001) and GaAs(001) substrates. QD properties were studied by Atomic Force Microscopy (AFM) and Photoluminescence (PL) spectroscopy. A wafer level µPL mapping of the entire 300 mm Ge/Si substrate shows the homogeneity of the three-stacked InAs QDs emitting at 1.30 ± 0.04 µm at room temperature. The correlation between PL spectroscopy and numerical modeling revealed, in accordance with transmission electron microscopy images, that buried QDs had a truncated pyramidal shape with base sides and heights around 29 and 4 nm, respectively. InAs QDs on Ge/Si substrate had the same shape as QDs on GaAs substrates, with a slightly increased size and reduced luminescence intensity. Our results suggest that 1.3 µm emitting InAs QDs quantum dots can be successfully grown on CMOS compatible Ge/Si substrates.

Novel Concept of Gas Sensitivity Characterization of Materials Suited for Implementation in FET-Based Gas Sensors.

We propose a novel technique to investigate the gas sensitivity of materials for implementation in field-effect transistor-based gas sensors. Our technique is based on the measurement of the surface charge induced by gas species adsorption, using an electrometer. Platinum sensitivity to hydrogen diluted in synthetic air has been evaluated with the proposed charge measurement technique in the operation temperature range from 80 to 190 °C at constant H2 concentration of 4 % and for different concentrations ranging from 0.5 to 4 % at 130 °C.