ABSTRACT
Three-dimensional photoactive self-standing porous materials have been synthesized through the integration of soft chemistry and colloids (emulsions, lyotrope mesophases, and P25 titania nanoparticles). Final multiscale porous ceramics bear 700-1000 m2 g-1 of micromesoporosity depending on the P25 nanoparticle contents. The applied thermal treatment does not affect the P25 anatase/rutile allotropic phase ratio. Photonic investigations correlated with the foams' morphologies suggest that the larger amount of TiO2 that is introduced, the larger the walls' density and the smaller the mean size of the void macroscopic diameters, with both effects inducing a reduction of the photon transport mean free path (lt) with the P25 content increase. A light penetration depth in the range of 6 mm is reached, thus depicting real 3D photonic scavenger behavior. The 3D photocatalytic properties of the MUB-200(x) series, studied in a dynamic "flow-through" configuration, show that the highest photoactivity (concentration of acetone ablated and concentration of CO2 formed) is obtained with the highest monolith height (volume) while providing an average of 75% mineralization. These experimental results validate the fact that these materials, bearing 3D photoactivity, are paving the path for air purification operating with self-standing porous monolith-type materials, which are much easier to handle than powders. As such, the photocatalytic systems can now be advantageously miniaturized, thereby offering indoor air treatment within vehicles/homes while drastically limiting the associated encumbrance. This volumetric counterintuitive acting mode for light-induced reactions may find other relevant advanced applications for photoinduced water splitting, solar fuel, and dye-sensitized solar cells while both optimizing photon scavenging and opening the path for the miniaturization of the processes where encumbrance or a foot-print penalty would be advantageously circumvented.
ABSTRACT
The formation of heterostructures has proven to be a viable way to achieve high photoelectrochemical water splitting efficiencies with BiVO4 based photoanodes. Especially, cobalt and nickel based oxides are suitable low cost contact materials. However, the exact role of these contact materials is not yet completely understood because of the difficulty to individually quantify the effects of surface passivation, charge carrier separation and catalysis on the efficiency of a heterostructure. In this study, we used photoelectron spectroscopy in combination with in situ thin film deposition to obtain direct information on the interface structure between polycrystalline BiVO4 and NiO, CoOx and Sn-doped In2O3 (ITO). Strong upwards band bending was observed for the BiVO4/NiO and BiVO4/CoOx interfaces without observing chemical changes in BiVO4, while limited band bending and reduction of Bi and V was observed while forming the BiVO4/ITO interface. Thus, the tunability of the Fermi level position within BiVO4 seems to be limited to a certain range. The feasibility of high upwards band bending through junctions with high work function (WF) compounds demonstrate that nickel oxide and cobalt oxide are able to enhance the charge carrier separation in BiVO4. Similar studies could help to identify whether new photoelectrode materials and their heterostructures would be suitable for photoelectrochemical water splitting.
ABSTRACT
Photovoltaic generation has stepped up within the last decade from outsider status to one of the important contributors of the ongoing energy transition, with about 1.7% of world electricity provided by solar cells. Progress in materials and production processes has played an important part in this development. Yet, there are many challenges before photovoltaics could provide clean, abundant, and cheap energy. Here, we review this research direction, with a focus on the results obtained within a Japan-French cooperation program, NextPV, working on promising solar cell technologies. The cooperation was focused on efficient photovoltaic devices, such as multijunction, ultrathin, intermediate band, and hot-carrier solar cells, and on printable solar cell materials such as colloidal quantum dots.
ABSTRACT
CeO2 nanocrystals (NCs) have attracted increasing interest over the past few years, in particular for their use in catalytic reactions. Syntheses mediated by near- and supercritical alcohols have proven to be innovative ways to obtain CeO2 NCs with controlled crystallite sizes (from 3 to 8â nm depending on the alcohol) and surface functionalities, with alcohol moieties. When submitted to a thermal treatment at 500 °C, required to desorb/degrade surface organic species, these powders displayed different behaviors depending on the alcohol used during the synthesis. Cerium oxide powders synthesized in sc-MeOH, sc-EtOH and sc-iPrOH undergo sintering during treatment at 500 °C, with a decrease of their specific surface area. Conversely, those synthesized in sc-BuOH, nc-PentOH and nc-HexOH keep their initial crystallite sizes and morphology, but show a great enhancement of their specific surface area (up to 200â m(2) g(-1)), which is unprecedented after such a thermal treatment.
ABSTRACT
New 2-6 wt% RuO2-ZnO heterojunction nanocatalysts were synthesized by a straightforward two-step procedure. They were composed of a porous network of aggregated 25 nm wurtzite ZnO nanocrystallites modified with RuO2 and showed enhanced light absorption in the visible region due to surface plasmon resonance. In order to investigate the energetic structure of the photocatalyst XPS core line and valence band spectra of in situ in UHV prepared heterointerfaces were compared to results obtained from the particles. The shift of Zn 2p3/2 and O 1s core level spectra was determined to be at least 0.80 ± 0.05 eV for the in situ prepared heterojunction whereas it was found to be 0.40 ± 0.05 and 0.45 ± 0.05 eV, respectively, in the photocatalysts. The different values were ascribed to the reduced size of the particles and the different measurability of band bending at the interface of the heterojunction RuO2-ZnO compared to the nanoparticles. The RuO2/ZnO photocatalysts showed higher photocatalytic activity and recyclability than pure ZnO for the degradation of various dyes under UV light irradiation due to vectorial charge separation of photogenerated electrons and holes resulting from internal electric field, the ruthenium oxide acting as a quasi-metallic contact.
ABSTRACT
The design and preparation of an asymmetric ruthenium-diacetylide organometallic complex was successfully achieved to provide an original donor-π-[M]-π-acceptor architecture, in which [M] corresponds to the [Ru(dppe)2] (dppe: bisdiphenylphosphinoethane) metal fragment. The charge-transfer processes occurring upon photoexcitation of the push-pull metal-dialkynyl σ complex were investigated by combining experimental and theoretical data. The novel push-pull complex, appropriately end capped with an anchoring carboxylic acid function, was further adsorbed onto a semiconducting metal oxide porous thin film to serve as a photosensitizer in hybrid solar cells. The resulting photoactive material, when embedded in dye-sensitized solar cell devices, showed a good spectral response with a broad incident photon-to-current conversion efficiency profile and a power conversion efficiency that reached 7.3 %. Thus, this material paves the way to a new generation of organometallic chromophores for photovoltaic applications.
ABSTRACT
New π-conjugated structures are constantly the subject of research in dyes and pigments industry and electronic organic field. In this context, the triphenodioxazine (TPDO) core has often been used as efficient photostable pigments and once integrated in air stable n-type organic field-effect transistor (OFET). However, little attention has been paid to the TPDO core as soluble materials for optoelectronic devices, possibly due to the harsh synthetic conditions and the insolubility of many compounds. To benefit from the photostability of TPDO in dye-sensitized solar cells (DSCs), an original synthetic pathway has been established to provide soluble and dissymmetric molecules applied to a suitable design for the sensitizers of DSC. The study has been pursued by the theoretical modeling of opto-electronic properties, the optical and electronic characterizations of dyes and elaboration of efficient devices. The discovery of new synthetic pathways opens the way to innovative designs of TPDO for materials used in organic electronics.
ABSTRACT
The fast and controlled synthesis of surface-modified cerium oxide nanoparticles was carried out in supercritical {ethanol + alcohol derivative} mixtures. The newly found ability of supercritical alcohols to graft onto cerium oxide nanocrystals (CeO2 NCs) during their synthesis was exploited to control their surface chemistry via the addition of three aminoalcohols: ethanolamine, 3-amino-1-propanol and 6-amino-1-hexanol. Although the ethanol to aminoalcohol ratio was consistent (285:1), the successful grafting of these alcohol derivatives onto CeO2 NCs was identified based on Fourier transform infrared (FTIR) and thermogravimetric analysis-mass spectrometry (TGA-MS) measurements. Smaller crystallite size of CeO2 NCs synthesized in the presence of aminoalcohols, compared to those synthesized in supercritical ethanol alone, were also noticed and attributed to a possible intervention of amine groups helping the grafting of the alcohols, allowing one to stop the growth of the CeO2 NCs faster. The use of supercritical alcohol mixture-ethanol with hexanol, dodecanol, or octadecanol, with a 285:1 ratio-was also investigated. Such mixtures allow accessing a finer control in CeO2 NCs crystallite size compared to pure alcohols, according to calculation made from X-ray diffraction measurements. Finally, fluorescent molecules (fluorescein isothiocyanate) were grafted onto amine-modified CeO2 NCs. The powders displayed a fluorescent behavior under UV light, confirming the suitability and interest of CeO2 NCs surface modification by such technique.
Subject(s)
Cerium/chemistry , Ethanolamine/chemistry , Nanoparticles/chemistry , Propanolamines/chemistryABSTRACT
Supercritical fluids offer fast and facile routes toward well-crystallized tailor-made cerium oxide nanoparticles. However, the use of surfactants to control morphology and surface properties remains essential. Therefore, although water, near-critical (nc) or supercritical (sc), is a solvent of choice, the poor water solubility of some surfactants could require other solvent systems such as alcohols, which could themselves behave as surface modifiers. In here, the influence of seven different alcohols, MeOH, EtOH, PrOH, iPrOH, ButOH, PentOH, and HexOH, in alcothermal conditions (300 °C, 24.5 MPa) over CeO(2) nanocrystals (NCs) size, morphology, and surface properties was investigated. The crystallite size of the CeO(2) nanocrystals can be tuned in the range 3-7 nm depending on the considered alcohol, and their surface has been modified by these solvents without the use of surfactants. Mechanisms are proposed for the interaction of primary and secondary alcohols with CeO(2) surface and its functionalization during the synthesis based on FTIR and TGA-MS studies. This study allows apprehending the role of alcohols during the synthesis and may lead to an informed choice of solvent as a function of the required size and surface properties of CeO(2) NCs. It also opens new route to CeO(2) functionalization using supercritical alcohol derivatives.
ABSTRACT
Nanoporous SnO(2)-ZnO heterojunction nanocatalyst was prepared by a straightforward two-step procedure involving, first, the synthesis of nanosized SnO(2) particles by homogeneous precipitation combined with a hydrothermal treatment and, second, the reaction of the as-prepared SnO(2) particles with zinc acetate followed by calcination at 500 °C. The resulting nanocatalysts were characterized by X-ray diffraction (XRD), FTIR, Raman, X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analyses, transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectroscopy. The SnO(2)-ZnO photocatalyst was made of a mesoporous network of aggregated wurtzite ZnO and cassiterite SnO(2) nanocrystallites, the size of which was estimated to be 27 and 4.5 nm, respectively, after calcination. According to UV-visible diffuse reflectance spectroscopy, the evident energy band gap value of the SnO(2)-ZnO photocatalyst was estimated to be 3.23 eV to be compared with those of pure SnO(2), that is, 3.7 eV, and ZnO, that is, 3.2 eV, analogues. The energy band diagram of the SnO(2)-ZnO heterostructure was directly determined by combining XPS and the energy band gap values. The valence band and conduction band offsets were calculated to be 0.70 ± 0.05 eV and 0.20 ± 0.05 eV, respectively, which revealed a type-II band alignment. Moreover, the heterostructure SnO(2)-ZnO photocatalyst showed much higher photocatalytic activities for the degradation of methylene blue than those of individual SnO(2) and ZnO nanomaterials. This behavior was rationalized in terms of better charge separation and the suppression of charge recombination in the SnO(2)-ZnO photocatalyst because of the energy difference between the conduction band edges of SnO(2) and ZnO as evidenced by the band alignment determination. Finally, this mesoporous SnO(2)-ZnO heterojunction nanocatalyst was stable and could be easily recycled several times opening new avenues for potential industrial applications.
Subject(s)
Methylene Blue/chemistry , Nanostructures/chemistry , Tin Compounds/chemistry , Zinc Oxide/chemistry , Catalysis , Particle Size , Photochemical Processes , Surface Properties , Tin Compounds/chemical synthesis , Zinc Oxide/chemical synthesisABSTRACT
A new straightforward synthetic strategy has been elaborated to achieve star-shaped triazatrinaphthylene and, for the first time, triazatrianthrylene derivatives. Their solution- and solid-state properties were thoroughly characterized by cyclic voltammetry, UV-vis absorption spectroscopy, X-ray diffraction, and density functional theory calculations. Original hexagonal molecular arrangements were found in the crystal phase, which opens a new pathway for designing materials with improved three-dimensional charge-transport properties.
ABSTRACT
Alkylation of aromatic hydrocarbons is among the most industrially important reactions, employing acid catalysts such as AlCl3, H2SO4, HF, or H3PO4. However, these catalysts present severe drawbacks, such as low selectivity and high corrosiveness. Taking advantage of the intrinsic high acid strength and Lewis and Brønsted acidity of niobium oxide, we have designed the first series of Nb2O5-SiO2(HIPE) monolithic catalysts bearing multiscale porosity through the integration of a sol-gel process and the physical chemistry of complex fluids. The MUB-105 series offers efficient solvent-free heterogeneous catalysis toward Friedel-Crafts monoalkylation and -acylation reactions, where 100% conversion has been reached at 140 °C while cycling. Alkylation reactions employing the MUB-105(1) catalyst have a maximum turnover number (TON) of 104 and a turnover frequency (TOF) of 9 h-1, whereas for acylation, MUB-105(1) and MUB-105(2) yield maximum TON and TOF values of 107 and 11 h-1, respectively. Moreover, the catalysts are selective, producing equal amounts of ortho- and para-substituted alkylated products and greater than 90% of the para-substituted acylated product. The highest catalytic efficiencies are obtained for the MUB-105(1) catalyst, bearing the smallest Nb2O5 particle sizes, lowest Nb2O5 content, and the highest amorphous character. The catalysts presented here are in a monolithic self-standing state, offering easy handling, reusability, and separation from the final products.
ABSTRACT
One of the biggest global challenges for our societies is to provide natural resources to the rapidly expanding population while maintaining sustainable and ecologically friendly products. The increasing public concern about toxic insecticides has resulted in the rapid development of alternative techniques based on natural infochemicals (ICs). ICs (e.g., pheromones, allelochemicals, volatile organic compounds) are secondary metabolites produced by plants and animals and used as information vectors governing their interactions. Such chemical language is the primary focus of chemical ecology, where behavior-modifying chemicals are used as tools for green pest management. The success of ecological programs highly depends on several factors, including the amount of ICs that enclose the crop, the range of their diffusion, and the uniformity of their application, which makes precise detection and quantification of ICs essential for efficient and profitable pest control. However, the sensing of such molecules remains challenging, and the number of devices able to detect ICs in air is so far limited. In this review, we will present the advances in sensing of ICs including biochemical sensors mimicking the olfactory system, chemical sensors, and sensor arrays (e-noses). We will also present several mathematical models used in integrated pest management to describe how ICs diffuse in the ambient air and how the structure of the odor plume affects the pest dynamics.
Subject(s)
Pheromones , Volatile Organic Compounds , Animals , Electronic Nose , Odorants , PlantsABSTRACT
Carbon from biomass as an active material for supercapacitor electrodes has attracted much interest due to its environmental soundness, abundance, and porous nature. In this context, activated carbon prepared from coconut shells via a simple activation process (water or steam as activation agents) was used as an active material in electrodes for eco-friendly supercapacitors. X-ray diffraction (XRD), Raman spectroscopy, conductivity, scanning electron microscopy (SEM), N2 sorption and thermogravimetry coupled to mass spectrometry (TGA-MS) studies revealed that activated carbon produced by this approach exhibit a graphitic phase, a high surface area, and large pore volume. The energy storage properties of activated carbon electrodes correlate with the morphological and structural properties of the precursor material. In particular, electrodes made of activated carbon exhibiting the largest Brunauer-Emmett-Teller (BET) surface area, i.e. 1998 m2 g-1, showed specific capacitance of 132.3 F g-1 in aqueous electrolyte (1.5 M H2SO4), using expanded graphite sheets as current collector substrates. Remarkably, this sample in a configuration with ionic liquid (1-methyl-1-propy-pyrrolizinium bis(fluorosulfonyl)mide) (MPPyFSI) as electrolyte and a polyethylene separator displayed an outstanding storage capability and energy-power handling capability of 219.4 F g-1 with a specific energy of 92.1 W h kg-1 and power density of 2046.9 W kg-1 at 1 A g-1 and maintains ultra-high values at 30 A g-1 indicating the ability for a broad potential of energy and power related applications. To the best of our knowledge, these values are the highest ever reported for ionic liquid-based supercapacitors with activated carbon obtained from the biomass of coconut shells.
ABSTRACT
Increased levels of nitrate (NO3-) in the environment can be detrimental to human health. Herein, we report a robust, cost-effective, and scalable, hybrid material-based colorimetric/luminescent sensor technology for rapid, selective, sensitive, and interference-free in situ NO3- detection. These hybrid materials are based on a square-planar platinum(II) salt [Pt(tpy)Cl]PF6 (tpy = 2,2';6',2â³-terpyridine) supported on mesoporous silica. The platinum salt undergoes a vivid change in color and luminescence upon exposure to aqueous NO3- anions at pH ≤ 0 caused by substitution of the PF6- anions by aqueous NO3-. This change in photophysics of the platinum salt is induced by a rearrangement of its crystal lattice that leads to an extended Pt···Pt···Pt interaction, along with a concomitant change in its electronic structure. Furthermore, incorporating the material into mesoporous silica enhances the surface area and increases the detection sensitivity. A NO3- detection limit of 0.05 mM (3.1 ppm) is achieved, which is sufficiently lower than the ambient water quality limit of 0.16 mM (10 ppm) set by the United States Environmental Protection Agency. The colorimetric/luminescence of the hybrid material is highly selective to aqueous NO3- anions in the presence of other interfering anions, suggesting that this material is a promising candidate for the rapid NO3- detection and quantification in practical samples without separation, concentration, or other pretreatment steps.
ABSTRACT
Facet-engineered monoclinic scheelite BiVO4 particles decorated with various cocatalysts were successfully synthesized by selective sunlight photodeposition of metal or metal oxy(hydroxide) nanoparticles onto the facets of truncated bipyramidal BiVO4 monoclinic crystals coexposing {010} and {110} facets. X-ray photoelectron spectroscopy, scanning electron microscopy, and scanning Auger microscopy revealed that metallic silver (Ag) and cobalt (oxy)hydroxide (CoOx(OH)y) particles were selectively deposited onto the {010} and {110} facets, respectively, regardless of the cocatalyst amount. By contrast, the nickel (oxy)hydroxide (NiOx(OH)y) photodeposition depends on the nickel precursor amount with an unprecedented selectivity for 0.1 wt % NiOx(OH)y/BiVO4 with a preferential deposition onto the {010} facets and the edges between the {110} facets. Moreover, these noble metal-free heterostructures led to remarkable photocatalytic properties for rhodamine B photodecomposition and sacrificial water oxidation reactions. For instance, 0.2 wt % CoOx(OH)y/BiVO4 led to one of the highest oxygen evolution rates, i.e., 1538 µmol h-1 g-1, ever described which is ten times higher than that found for bare BiVO4. The selective deposition of cobalt (oxy)hydroxide species onto the more electron-deficient facet of truncated bipyramidal monoclinic BiVO4 particles favors photogenerated charge carrier separation and therefore plays a key role for efficient photochemical oxygen evolution.
ABSTRACT
By using 1,2-propanediol instead of the classic polyol solvent, ethylene glycol, ultra-long silver nanowires are obtained in only 1 h. These nanowires lead to transparent electrodes with a sheet resistance of 5 Ohms per sq at a transparency of 94%, one of the highest figures of merit for nanowire electrodes ever reported.
ABSTRACT
A highly selective chemisensor for 2-nitrophenol detection was fabricated using ZnO/RuO2 nanoparticles (NPs) synthesized by impregnation method. The as-synthesized NPs were characterized through UV-vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), Energy dispersive X-ray spectroscopy (EDS), FTIR and X-ray diffraction (XRD). A glassy carbon electrode was modified with as-synthesized ZnO/RuO2 nanoparticles and utilized as a chemical sensor for the detection of 2-nitrophenol. The fabricated sensor exhibited excellent sensitivity (18.20 µA µM-1 cm-2), good reproducibility, short response time (8.0 s.), the lowest detection limit (52.20 ± 2.60 pM) and long-term stability in aqueous phase without interference effects. Finally, the fabricated sensor was validated as a 2-NP probe in various environmental water samples at room conditions.
ABSTRACT
Tin dioxide (SnO2) nanoparticles were straightforwardly synthesized using an easily scaled-up liquid route that involves the hydrothermal treatment, either under acidic or basic conditions, of a commercial tin dioxide particle suspension including potassium counterions. After further thermal post-treatment, the nanomaterials have been thoroughly characterized by Fourier transform infrared and Raman spectroscopy, powder X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, and nitrogen sorption porosimetry. Varying pH conditions and temperature of the thermal treatment provided cassiterite SnO2 nanoparticles with crystallite sizes ranging from 7.3 to 9.7 nm and Brunauer-Emmett-Teller surface areas ranging from 61 to 106 m2·g-1, acidic conditions favoring potassium cation removal. Upon exposure to a reducing gas (H2, CO, and volatile organic compounds such as ethanol and acetone) or oxidizing gas (NO2), layers of these SnO2 nanoparticles led to highly sensitive, reversible, and reproducible responses. The sensing results were discussed in regard to the crystallite size, specific area, valence band energy, Debye length, and chemical composition. Results highlight the impact of the counterion residuals, which affect the gas-sensing performance to an extent much higher than that of size and surface area effects. Tin dioxide nanoparticles prepared under acidic conditions and calcined in air showed the best sensing performances because of lower amount of potassium cations and higher crystallinity, despite the lower surface area.
ABSTRACT
The hydrolysis of a bridged alpha,omega-bis(trialkynylstannylated) compound leads to a hybrid material ordered by self-assembly where the spacer forms two six-membered [1,2]oxastanninane rings by intramolecular coordination.