Ultrafast and Parts-per-Billion-Level MEMS Gas Sensors by Hetero-Interface Engineering of 2D/2D Cu-TCPP@ZnIn2S4 with Enriched Surface Sulfur Vacancies.

The primary challenge for resonant-gravimetric gas sensors is the synchronous improvement of the sensitivity and response time, which is restricted by low adsorption capacity and slow mass transfer in the sensing process and remains a great challenge. In this study, a novel 2D/2D Cu-TCPP@ZnIn2S4 composite is successfully constructed, in which Cu-TCPP MOF is used as a core substrate for the growth of 2D ultrathin ZnIn2S4 nanosheets with well-defined {0001} crystalline facets. The Cu-TCPP@ZnIn2S4 sensor exhibited high sensitivity (1.5 Hz@50 and 2.3 Hz@100 ppb), limit of detection (LOD: 50 ppb), and ultrafast (9 s @500 ppb) detection of triethylamine (TEA), which is the lowest LOD and the fastest sensor among the reported TEA sensors at room temperature, tackling the bottleneck for the ultrafast detection of the resonant-gravimetric sensor. These above results provide an innovative and easily achievable pathway for the synthesis of heterogeneous structure sensing materials.

Loureirin A is a narrow-spectrum antimicrobial agent against Helicobacter pylori.

Currently, Helicobacter pylori eradication by antibiotic therapy faces various challenges, including antibiotic resistance, side effects on intestinal commensal bacteria, and patient compliance. In this study, loureirin A (LrA), a traditional Chinese medicine monomer extracted from Sanguis Draconis flavones, was found to possess specific antibacterial activity against H. pylori without the bacteria displaying a tendency to develop resistance in vitro. LrA demonstrated a synergistic or additive effect when combined with omeprazole (a proton pump inhibitor) against H. pylori. The combination of LrA and omeprazole showed promising anti-H. pylori potential, exhibiting notable in vivo efficacy comparable to standard triple therapy in mouse models infected with both drug-sensitive and drug-resistant H. pylori strains. Moreover, the narrow-spectrum antibacterial profile of LrA is reflected in its minimal effect on the diversity and composition of the mouse gut microbiota. The underlying mechanism of action of LrA against H. pylori involves the generation of bactericidal levels of reactive oxygen species, resulting in apoptosis-like cell death. These findings indicate that LrA is a promising lead compound targeting H. pylori without harming the commensal bacteria.

Transition Metal Functionalized C30N12S6 as High-Performance Trifunctional Catalysts with Integrated Descriptors toward Hydrogen Evolution, Oxygen Evolution, and Oxygen Reduction Reactions: A Case of High-Throughput First-Principles Screening within the Framework of TM-N2@C30N10S6.

In energy conversion and storage technologies, the design of highly efficient trifunctional electrocatalysts integrating with the high hydrogen evolution reaction (HER) and oxygen evolution/reduction reaction (OER/ORR) activities is highly desirable. Herein, utilizing first-principles computations, a novel periodically ordered macropore C30N12S6 monolayer was proposed, and the stability analysis attests to its good stability. Single transition metal (TM) atom anchored onto this newly proposed C30N12S6 monolayer to form single-atom catalysts, as achieved by TM-N2@C30N10S6, among which the Co-N2@C30N10S6 is the most promising multifunctional catalyst toward HER/OER/ORR with low overpotential of 0.01/0.59/0.3 V; meanwhile, the Rh-N2@C30N10S6 can be used as a bifunctional OER/ORR catalyst with low overpotential of 0.37/0.44 V, overmatching the landmark Pt (111) and IrO2/RuO2 catalysts. Particularly, the TM-d orbital in TM@CNS is remarkably hybridized with the O-p orbital of oxygenated intermediates, so that the lone electrons initially located at the antibonding orbital pair up and fill the downward bonding orbital, allowing OH* to be suitably adsorbed on TM@CNS, enhancing the catalytic performance. The relevant attributes, such as good stabilities and metallic features, ensured their applications in ambient conditions. Moreover, multilevel descriptors were constructed to clarify the origin of activity on TM@CNS, such as ΔGOH* (Gibbs free energy of OH*), εd (d-band center), COHP (crystal orbital Hamilton population), Nd/Nd + s (number of d/d + s electrons) and φ (descriptor), among which the filling of outer d-electrons of TM atom significantly affects the value of ΔGOH* that can determine the overpotential and, thus, become a key descriptor.

Changes in clinical outcomes and alignment of the ipsilateral knee and ankle after supramalleolar osteotomy in patients with varus osteoarthritis of the ankle: a short-term follow-up study.

PURPOSE: The purpose of this study was to investigate the changes in clinical outcomes and alignment of the ipsilateral knee and ankle in patients with varus ankle osteoarthritis after supramalleolar osteotomy (SMO). METHODS: We retrospectively reviewed 23 patients (24 ankles) with Takakura II, IIIa and IIIb ankle osteoarthritis treated with SMO between May 2017 and March 2022. The radiologic parameters of ankles contained medial distal tibial angle (TAS), tibiotalar angle (TT), tibial lateral surface (TLS), tibial plafond inclination (TPI) and talar inclination (TI). The radiologic parameters of knees contained medial proximal tibial angle (MPTA), joint line convergence angle (JLCA), the knee joint line orientation relative to ground (G-KJLO) and WBL. Hip-knee-ankle angle (HKA) was also collected. The Takakura system was used for evaluating the ankle osteoarthritis and the Kellgren-Lawrence (KL) system was used for evaluating the knee osteoarthritis. Clinical evaluation of the ankle joints contained American Orthopedic Foot and Ankle Society (AOFAS), range of motion (ROM) and visual analogue scale (VAS). Clinical evaluation of the knee joints contained Japanese Orthopaedic Association Scores (JOA), ROM, VAS. RESULTS: The mean follow-up times were 20.3 ± 7.3 months (range 12-38). According to the radiologic evaluation, the TAS increased from preoperative 84.7° ± 2.0° to 91.2° ± 1.8° at the last follow-up (P < 0.001). The TPI and TI decreased from 4.4° ± 4.2° and 11.0° ± 5.2° to 0.1° ± 4.7° and 4.1° ± 4.8° (P < 0.001 for both). The TT angel improved from 9.5° ± 4.1° to 4.9° ± 3.3° (P < 0.001). No significant differences were found regarding MPTA, JLCA, G-KJLO, knee WBL and HKA (P > 0.05 for all). The Takakura stage improved after SMO (P < 0.001) whilst the KL stage maintains the similar lever (P > 0.05). According to the clinical evaluation, the AOFAS significantly increased from 67.5 ± 10.6 to 88.5 ± 9.3 and the VAS of the ankle decreased from 4.7 ± 1.6 to 1.2 ± 1.1, whilst there were no changes on VAS and even the JOA and knee ROM after SMO (P > 0.05 for all). CONCLUSIONS: SMO can alleviate the symptoms of varus ankle osteoarthritis and delay the time for ankle replacement or arthrodesis by redistributing the abnormal stress of the ankle and restoring the congruence of the tibiotalar joint. In addition, it did not induce the clinical symptoms of knee without compromising lower limb alignment or knee joint line orientation in the short term. LEVEL OF EVIDENCE: Level IV case series.

Kagome-like BiP3 Monolayer: An Emerging Quasi-Direct Auxetic Semiconductor Coupled with High Anisotropic Mobility toward Visible-Light-Driven Photoelectrocatalytic pH-Robust Overall Water-Splitting.

Two-dimensional (2D) Janus materials exhibit an outstanding potential that can meet the rigorous requirements of photocatalytic water splitting resulting from their unique atomic arrangement. However, these materials are quite scarce. Through ab initio density functional theory calculations, we introduce a kagome topology into the honeycomb lattice of blue phosphorene using phosphorus and bismuth atoms to build a hybrid honeycomb-like kagome lattice, realized by a hitherto unknown kagome-like Janus-like BiP3 monolayer with robust stability. Excitingly, the out-of-plane asymmetry benefiting from kagome and honeycomb topologies gives rise to a significantly negative out-of-plane Poisson's ratio and an obvious built-in electric field pointing from the sublayer of the P atom to the sublayer of the Bi atom. In conjunction with the investigations that encompass semiconducting properties, such as a quasi-direct gap, suitable band-edge positions, effective visible-light absorption, and high carrier mobility, the BiP3 monolayer achieves overall water splitting at pH 0-14 regardless of strain. Moreover, this intrinsic electric field provides a sufficient photogenerated carrier driving force for water splitting. The bare BiP3 comprises P and Bi atoms that function as catalysts for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) active sites, respectively. Upon exposure to light, the reaction of water into H2 and O2 can be observed across a pH range of 0-14. Meanwhile, by designing a transition-metal single-atom catalyst (TM@BiP3), our investigations have shown that embedding a single TM on BiP3 is a feasible route to improving the HER/OER activity by reducing the overpotentials to -0.039 and 0.58 eV for Mo and Os atoms, respectively. In this case, the positive value of the external potential acts as a sufficient OER driving force, i.e., in the light environment, the Os@BiP3 system can promote water molecules spontaneously oxidized into O2 at pH 0-14.

UWB Localization Based on Improved Robust Adaptive Cubature Kalman Filter.

Aiming at the problems of Non-Line-of-Sight (NLOS) observation errors and inaccurate kinematic model in ultra-wideband (UWB) systems, this paper proposed an improved robust adaptive cubature Kalman filter (IRACKF). Robust and adaptive filtering can weaken the influence of observed outliers and kinematic model errors on filtering, respectively. However, their application conditions are different, and improper use may reduce positioning accuracy. Therefore, this paper designed a sliding window recognition scheme based on polynomial fitting, which can process the observation data in real-time to identify error types. Simulation and experimental results indicate that compared to the robust CKF, adaptive CKF, and robust adaptive CKF, the IRACKF algorithm reduces the position error by 38.0%, 45.1%, and 25.3%, respectively. The proposed IRACKF algorithm significantly improves the positioning accuracy and stability of the UWB system.

Two-Dimensional MoS2 for Resonant-Gravimetric Detection of Ppb-Level Formaldehyde.

The development of formaldehyde (HCHO) gas sensors with high sensitivity, good selectivity, and fast response at room temperature is an important research topic. The resonant microcantilever, with high sensitivity, easy batch manufacturing, and integration, generates sensing signals based on the relationship between the frequency and the mass addition of the adsorbed molecules and shows good application potential in HCHO detection. Herein, we report two species of MoS2 nanosheets (NSs) with 1T and 2H phases as sensitive materials to construct high-performance HCHO resonant cantilever sensors. The 2H-MoS2 gas sensors show better sensitivity toward HCHO compared to the 1T-MoS2 gas sensor. Specifically, the 2H-MoS2 sensor displayed a high sensitivity (Hz) of 13.6-1 ppm HCHO at room temperature, with high selectivity, low limit of detection (10 ppb), and good humidity resistance. The effect of phase structures on the sensing performance was studied by in situ characterizations, thermodynamic analysis, and density functional theory calculations. The good sensing ability could be attributed to the abundant active sites induced by the surface defects, suitable adsorption strength, and the outstanding thermodynamic performance of the 2H-MoS2. The combination of two-dimensional (2D) nanosheet and microcantilever sensors provides a new direction for developing a high-performance room-temperature gas sensor in the future.

Identifiability of local and global features of phylogenetic networks from average distances.

Phylogenetic networks extend phylogenetic trees to model non-vertical inheritance, by which a lineage inherits material from multiple parents. The computational complexity of estimating phylogenetic networks from genome-wide data with likelihood-based methods limits the size of networks that can be handled. Methods based on pairwise distances could offer faster alternatives. We study here the information that average pairwise distances contain on the underlying phylogenetic network, by characterizing local and global features that can or cannot be identified. For general networks, we clarify that the root and edge lengths adjacent to reticulations are not identifiable, and then focus on the class of zipped-up semidirected networks. We provide a criterion to swap subgraphs locally, such as 3-cycles, resulting in indistinguishable networks. We propose the "distance split tree", which can be constructed from pairwise distances, and prove that it is a refinement of the network's tree of blobs, capturing the tree-like features of the network. For level-1 networks, this distance split tree is equal to the tree of blobs refined to separate polytomies from blobs, and we prove that the mixed representation of the network is identifiable. The information loss is localized around 4-cycles, for which the placement of the reticulation is unidentifiable. The mixed representation combines split edges for 4-cycles, regular tree and hybrid edges from the semidirected network, and edge parameters that encode all information identifiable from average pairwise distances.

Revealing the Influences of Solvent Boiling Point and Alkyl Chains on the Adlayer Crystallinity of Furan-Diketopyrrolopyrrole-Thienylene Copolymer at Molecular Level.

Crystallinity of the polymer poly(3,6-difuran-2-yl-2,5-di(2-octyldodecyl)-pyrrolo[3,4-c]pyrrole-1,4-dione-altthieylenevinylene) (PDVF) adlayers casted from low-boiling-point (L-bp), medium-bp (M-bp), and high-bp (H-bp) solvents was investigated through scanning tunneling microscopy (STM) and analyzed by the assistance of Hansen solubility parameter (HSP) theory and molecular dynamics (MD) simulations. Crystallinity of the PDVF adlayers increases evidently from the L- to H-bp solvents. Also, the solvent with an alkyl chain such as ethylbenzene (EB) facilitates in improving the crystallinity than the one without an alkyl chain such as chlorobenzene (CB) if the solvent bp is present in the same group. The HSP space discloses that EB is a marginal solvent for PDVF in contrast to CB. Quasi-isolate PDVF in the EB solution revealed by MD simulations facilitates the formation of crystallized domains through surface assembling mechanism. However, in CB, interconnected PDVF molecules through intermolecular overlapping tend to generate amorphous structures through direct deposition of the preformed structures in solution.

Facile Synthesis of Highly Efficient Amorphous Mn-MIL-100 Catalysts: Formation Mechanism and Structure Changes during Application in CO Oxidation.

A comprehensive study was carried out on amorphous metal-organic frameworks Mn-MIL-100 as efficient catalysts for CO oxidation. This study focused on explaining the crystalline-amorphous-crystalline transformations during thermolysis of Mn-MIL-100 and studying the structure changes during the CO oxidation reaction. A possible formation mechanism of amorphous Mn-MIL-100 was proposed. Amorphous Mn-MIL-100 obtained by calcination at 250 °C (a-Mn-250) showed a smaller specific surface area (4 m2 g-1 ) but high catalytic activity. Furthermore, the structure of amorphous Mn-MIL-100 was labile during the reaction. When a-Mn-250 was treated with reaction atmosphere at high temperature (giving used-a-Mn-250-S), the amorphous catalysts transformed into Mn2 O3 . Meanwhile, the BET surface area (164 m2 g-1 ) and catalytic performance both sharply increased. In addition, used-a-Mn-250-S catalyst transformed from Mn2 O3 into Mn3 O4 , and this resulted in a slight decrease of catalytic activity in the presence of 1 vol % water vapor in the feed stream. A schematic mechanism of the structure changes during the reaction process was proposed. The success of the synthesis relies on the increase in BET surface area by using CO as retreatment atmosphere, and the enhanced catalytic activity was attributed to the unique structure, a large quantity of surface active oxygen species, oxygen vacancies, and good low-temperature reduction behavior.

Utilization of lime-dried sludge for eco-cement clinker production: effects of different feeding points.

Co-processing lime-dried sludge (LDS) in cement kilns is an appropriate technique to solve the problem of LDS disposal and promote the sustainable development for cement industry. However, there were limited studies that investigated the effects of feeding points on product quality and cement kiln emissions. In this study, simulated experiments were conducted by dividing the feeding points into high-temperature zones (HTZs) and raw mill (RM). Cement quality and major cement kiln emission characteristics were comprehensively investigated. The results showed that in terms of burnability, compressive strength and microstructure, the optimum co-processing amount of LDS were 9 wt% when feeding at RM, while 6% when feeding at HTZs. Meanwhile, the organic emissions of RM samples were mainly low environmental risk compounds of amides and nitrogenous heterocyclic compounds. Inorganic gaseous pollutions of NOX and SO2, respectively, were 8.11 mg/g DS and 12.89 mg/g DS, compared with 7.61 mg/g DS and 4.44 mg/g DS for HTZs. However, all the cement kiln emissions concentration were still much lower than standard requirements. Overall, RM had a bigger LDS co-processing capacity and higher, but acceptable, cement kiln emissions. Feeding LDS via RM could dispose larger amounts of sludge and provide more alternative materials for cement manufacturing.

Use of horizontal subsurface flow constructed wetlands to treat reverse osmosis concentrate of rolling wastewater.

According to the characteristics of the reverse osmosis concentrate (ROC) generated from iron and steel company, we used three sets of parallel horizontal subsurface flow (HSF) constructed wetlands (CWs) with different plants and substrate layouts to treat the high-salinity wastewater. The plant growth and removal efficiencies under saline condition were evaluated. The evaluation was based entirely on routinely collected water quality data and the physical and chemical characteristics of the plants (Phragmites australis, Typha latifolia, Iris wilsonii, and Scirpus planiculmis). The principal parameters of concern in the effluent were chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP). The results showed that the CWs were able to remove COD, TN, and TP from ROC. S. planiculmis was not suitable for the treatment of high-saline wastewater. The sequence of metals accumulated in CW plants was K>Ca>Na>Mg>Zn>Cu. More than 70% of metals were accumulated in the aboveground of P. australis. The CW filled with gravel and manganese ore and planted with P. australis and T. latifolia had the best performance of pollutant removal, with average removal of 49.96%, 39.45%, and 72.01% for COD, TN, and TP, respectively. The effluent water quality met the regulation in China. These results suggested that HSF CW planted with P. australis and T. latifolia can be applied for ROC pollutants removal.

The effect of lime-dried sewage sludge on the heat-resistance of eco-cement.

The treatment and disposal of sewage sludge is a growing problem for sewage treatment plants. One method of disposal is to use sewage sludge as partial replacement for raw material in cement manufacture. Although this process has been well researched, little attention has been given to the thermal properties of cement that has had sewage sludge incorporated in the manufacturing process. This study investigated the fire endurance of eco-cement to which lime-dried sludge (LDS) had been added. LDS was added in proportions of 0%, 3%, 6%, 9%, and 12% (by weight) to the raw material. The eco-cement was exposed to 200, 400, or 600 °C for 3 h. The residual strength and the microstructural properties of eco-cement were then studied. Results showed that the eco-cement samples suffered less damage than conventional cement at 600 °C. The microstructural studies showed that LDS incorporation could reduce Ca(OH)(2) content. It was concluded that LDS has the potential to improve the heat resistance of eco-cement products.

Characteristics of ammonia emission during thermal drying of lime sludge for co-combustion in cement kilns.

Thermal drying was used to reduce sludge moisture content before co-combustion in cement kilns. The characteristics of ammonia (NH3) emission during thermal drying of lime sludge (LS) were investigated in a laboratory-scale tubular dry furnace under different temperature and time conditions. As the temperature increased, the NH3 concentration increased in the temperature range 100-130°C, decreased in the temperature range 130-220°C and increased rapidly at >220°C. Emission of NH3 also increased as the lime dosage increased and stabilized at lime dosages>5%. In the first 60 min of drying experiments, 55% of the NH3 was released. NH3 accounted for about 67-72% of the change in total nitrogen caused by the release of nitrogen-containing volatile compounds (VCs) from the sludge. X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy revealed that the main forms of nitrogen in sludge were amides and amines. The addition of lime (CaO) could cause conversion of N-H, N-O or C-N containing compounds to NH3 during the drying process.

Algae separation from urban landscape water using a high density microbubble layer enhanced by micro-flocculation.

Eutrophication of raw water results in outbreaks of algae, which hinders conventional water treatment. In this study, high density microbubble layers combined with micro-flocculation was adopted to remove algae from urban landscape water, and the effects of pressure, hydraulic loading, microbubble layer height and flocculation dosage on the removal efficiency for algae were studied. The greatest removal efficiency for algae, chemical oxygen demand, nitrogen and phosphorus was obtained at 0.42 MPa with hydraulic loading at 5 m/h and a flocculation dosage of 4 mg/L using a microbubble layer with a height of 130 cm. Moreover, the size, clearance distance and concentration of microbubbles were found to be affected by pressure and the height of the microbubble layer. Based on the study, this method was an alternative for algae separation from urban landscape water and water purification.

Pollution Characteristics of Heavy Metals in PM1 and Source-Specific Health Risks in the Tianjin Airport Community, China.

The airport and its surrounding areas are home to a variety of pollution sources, and air pollution is a recognized health concern for local populated regions. Submicron particulate matter (PM1 with an aerodynamic diameter of <1 mm) is a typical pollutant at airports, and the enrichment of heavy metals (HMs) in PM1 poses a great threat to human health. To comprehensively assess the source-specific health effects of PM1-bound HMs in an airport community, PM1 filter samples were collected around the Tianjin Binhai International Airport for 12 h during the daytime and nighttime, both in the spring and summer, and 10 selected HMs (V, Cr, Mn, Co, Ni, Cu, Zn, As, Cd, and Pb) were analyzed. The indicatory elements of aircraft emissions were certified as Zn and Pb, which accounted for more than 60% of the sum concentration of detected HMs. The health risks assessment showed that the total non-cancer risks (TNCRs) of PM1-bound HMs were 0.28 in the spring and 0.23 in the summer, which are lower than the safety level determined by the USEPA, and the total cancer risk (TCR) was 2.37 × 10-5 in the spring and 2.42 × 10-5 in the summer, implying that there were non-negligible cancer risks in the Tianjin Airport Community. After source apportionment with EF values and PMF model, four factors have been determined in both seasons. Consequently, the source-specific health risks were also evaluated by combining the PMF model with the health risk assessment model. For non-cancer risk, industrial sources containing high concentrations of Mn were the top contributors in both spring (50.4%) and summer (44.2%), while coal combustion with high loads of As and Cd posed the highest cancer risk in both seasons. From the perspective of health risk management, targeted management and control strategies should be adopted for industrial emissions and coal combustion in the Tianjin Airport Community.

[Comparison of talonavicular-cuneiform joint fusion with bone grafting and without bone grafting in treatment of Müller-Weiss disease].

Objective: To compare the effectiveness of talonavicular-cuneiform joint fusion with iliac bone grafting and without bone grafting in the treatment of Müller-Weiss diseases (MWD). Methods: The clinical data of 44 patients (44 feet) with MWD who received talonavicular-cuneiform joint fusion between January 2017 and November 2022 and met the selection criteria was retrospectively analyzed. Among them, 25 patients were treated with structural iliac bone grafting (bone grafting group) and 19 patients without bone grafting (non-bone grafting group). There was no significant difference ( P>0.05) in age, gender composition, body mass index, disease duration, affected side, Maceira stage, and preoperative American Orthopaedic Foot and Ankle Society (AOFAS) score, visual analogue scale (VAS) score, anteroposterior/lateral Meary angle, and Pitch angle between the two groups. Operation time, operation cost, and postoperative complications were recorded in the two groups. AOFAS and VAS scores were used to evaluate the function and pain degree of the affected foot. Meary angle and Pitch angle were measured on the X-ray film, and the joint fusion was observed after operation. The difference (change value) of the above indexes before and after operation was calculated for comparison between groups to evaluate the difference in effectiveness. Results: The operation was successfully completed in both groups, and the incisions in the two groups healed by first intention. The operation time and cost in the bone grafting group were significantly more than those in the non-bone grafting group ( P<0.05). All patients were followed up. The median follow-up time was 41.0 months (range, 16-77 months) in the non-bone grafting group and 40.0 months (range, 16-80 months) in the bone grafting group. There was skin numbness of the medial dorsalis of the foot in 1 case, internal fixation stimulation in 2 cases, and pain at the iliac bone harvesting area in 1 case of the bone grafting group. There was skin numbness of the medial dorsalis of the foot in 1 case and muscle atrophy of the lower limb in 1 case of the non-bone grafting group. There was no significant difference in the incidence of complications between the two groups ( P>0.05). At last follow-up, the AOFAS scores of the two groups significantly improved when compared with those before operation, while the VAS scores significantly decreased, the anteroposterior/lateral Meary angle and Pitch angle significantly improved, and the differences were significant ( P<0.05). There was no significant difference in the change values of outcome indicators between the two groups ( P>0.05). There was no delayed bone union or bone nonunion in both groups, and joint fusion was achieved at last follow-up. Conclusion: In the treatment of MWD, there is no significant difference in effectiveness and imaging improvement of talonavicular-cuneiform joint fusion combined with or without bone grafting. However, non-bone grafting can shorten the operation time, reduce the cost, and may avoid the complications of bone donor site.

The Effects of Different Durations of Night-Time Supplementary Lighting on the Growth, Yield, Quality and Economic Returns of Tomato.

To achieve higher economic returns, we employ inexpensive valley electricity for night-time supplementary lighting (NSL) of tomato plants, investigating the effects of various durations of NSL on the growth, yield, and quality of tomato. Tomato plants were treated with supplementary light for a period of 0 h, 3 h, 4 h, and 5 h during the autumn-winter season. The findings revealed superior growth and yield of tomato plants exposed to 3 h, 4 h, and 5 h of NSL compared to their untreated counterparts. Notably, providing lighting for 3 h demonstrated greater yields per plant and per trough than 5 h exposure. To investigate if a reduced duration of NSL would display similar effects on the growth and yield of tomato plants, tomato plants received supplementary light for 0 h, 1 h, 2 h, and 3 h at night during the early spring season. Compared to the control group, the stem diameter, chlorophyll content, photosynthesis rate, and yield of tomatoes significantly increased upon supplementation with lighting. Furthermore, the input-output ratios of 1 h, 2 h, and 3 h NSL were calculated as 1:10.11, 1:4.38, and 1:3.92, respectively. Nonetheless, there was no detectable difference in yield between the 1 h, 2 h, and 3 h NSL groups. These findings imply that supplemental LED lighting at night affects tomato growth in the form of light signals. Night-time supplemental lighting duration of 1 h is beneficial to plant growth and yield, and its input-output ratio is the lowest, which is an appropriate NSL mode for tomato cultivation.

[Influence and risk factors of lateral hinge fracture on early effectiveness of supramalleolar osteotomy].

Objective: To evaluate the influence of lateral hinge fracture (LHF) on the early effectiveness of supramalleolar osteotomy (SMO) and to explore the related risk factors for LHF. Methods: A total of 39 patients (39 feet) with varus-type ankle osteoarthritis treated with SMO between January 2016 and December 2022 were analyzed retrospectively. There were 10 males and 29 females, aged from 41 to 71 years (mean, 57.7 years). According to Takakura stage, there were 6 feet in stage Ⅱ, 19 feet in stage Ⅲa, and 14 feet in stage Ⅲb. The LHF was recognized by the immediate postoperative X-ray film. The osteotomy healing time and the changes of pain visual analogue scale (VAS) score, American Orthopaedic Foot and Ankle Society (AOFAS) score, tibial anterior surface angle (TAS), tibial lateral surface angle (TLS), and tibiotalar angle (TT) before and after operation were compared between patients with and without LHF. The age, gender, affected side, body mass index, Takakura stage, preoperative VAS score, preoperative AOFAS score, preoperative TAS, preoperative TLS, preoperative TT, SMO correction angle, osteotomy distraction, distance from medial osteotomy to ankle joint line (MD), and distance from lateral osteotomy to ankle joint line (LD) were compared between with and without LHF patients, and further logistic regression analysis was used to screen the risk factors of LHF during SMO. Results: All patients were followed up 12-54 months (mean, 27.1 months). During operation, 13 feet developed LHF (group A) and 26 feet did not develop LHF (group B). X-ray film reexamination showed that 1 patient in group A complicated with tibial articular surface cleft fracture had delayed osteotomy and healed successfully after plaster fixation; the osteotomy of other patients healed, and there was no significant difference in healing time between the two groups ( P>0.05). At last follow-up, there were significant differences in VAS score, AOFAS score, TAS, TLS, and TT of the two groups when compared with preoperative ones ( P<0.05), but there was no significant difference in the changes of above indicators before and after operation between the two groups ( P>0.05). The differences in SMO correction angle, osteotomy distraction, and LD between with and without LHF patients were significant ( P<0.05), and further logistic regression analysis showed that excessive LD was the risk factor of LHF during SMO ( P<0.05). Conclusion: Too high or too low lateral hinge position during SMO may lead to LHF, but as long as appropriate treatment and rehabilitation measurements are taken, the early effectiveness is similar to that of patients without LHF.

Photonic Pigments of Polystyrene-block-Polyvinylpyrrolidone Bottlebrush Block Copolymers via Sustainable Organized Spontaneous Emulsification.

Prior studies on photonic pigments of amphiphilic bottlebrush block copolymers (BBCPs) through an organized spontaneous emulsification (OSE) mechanism have been limited to using polyethylene glycol (PEG) as the hydrophilic side chains and toluene as the organic phase. Herein, a family of polystyrene-block-polyvinylpyrrolidone (PS-b-PVP) BBCPs are synthesized with PVP as the hydrophilic block. Biocompatible and sustainable anisole is employed for dissolving the obtained BBCPs followed by emulsification of the solutions in water. Subsequent evaporation of oil-in-water emulsion droplets triggers the OSE mechanism, producing thermodynamically stable water-in-oil-in-water (w/o/w) multiple emulsions with uniform and closely packed internal droplet arrays through the assembly of the BBCPs at the w/o interface. Upon solidification, the homogeneous porous structures are formed within the photonic microparticles that exhibit visible structural colors. The pore diameter is widely tunable (150∼314 nm) by changing the degree of polymerization of BBCP (69∼110), resulting in tunable colors across the whole visible spectrum. This work demonstrates useful knowledge that OSE can be generally used in the fabrication of ordered porous materials with tunable internal functional groups, not only for photonic applications, but also offers a potential platform for catalysis, sensing, separation, encapsulation, etc.