Refractive index sensor based on a ring with a disk-shaped cavity for temperature detection applications.

In this study, we proposed a novel refractive index sensor structure, comprising a metal-insulator-metal (MIM) waveguide and a circular ring containing a disk-shaped cavity (CRDC). The finite element method was used to theoretically analyze the sensor characteristics. The simulation results showed that the disk-shaped cavity is the key to the asymmetric Fano resonance, and the radius of the CRDC has a significant influence on the performance of the sensor. A maximum sensitivity and figure of merit (FOM) of 2240 nm/RIU and 62.5, respectively, were realized. Additionally, the refractive index sensor exhibits the potential of aiding in temperature detection owing to its simple structure and high sensitivity of 1.186 nm/ºC.

Refractive Index and Alcohol-Concentration Sensor Based on Fano Phenomenon.

A novel nano-refractive index sensor based on the Fano resonance phenomenon is proposed in this paper. The sensor consists of the metal-insulator-metal (MIM) waveguide and a V-ring cavity with a groove (VRCG). We analyzed the performance of the nanoscale sensor using the finite element method. The simulation results show that the asymmetry of the geometric structure itself is the main factor leading to Fano resonance splitting. In Fano splitting mode, the Fano bandwidth of the system can be significantly reduced when the sensor sensitivity is slightly reduced, so that the figure of merit (FOM) of the sensor can be substantially improved. Based on the above advantages, the sensor's sensitivity in this paper is as high as 2765 nm/RIU, FOM = 50.28. In addition, we further applied the sensor to alcohol concentration detection. The effect is good, and the sensitivity achieves about 150. This type of sensor has a bright future in the precision measurement of solution concentrations.

Pulsed vapor cell atomic clock with a differential Faraday rotation angle detection.

Laser intensity noise is one of the main limiting factors in pulsed vapor cell clocks. To reduce the contribution of the laser intensity noise to detection signal in the pulsed optically pumped atomic clock, a scheme based on the differential Faraday rotation angle is proposed. Theoretically, the Ramsey fringes, the sensitivity of clock frequency to laser intensity fluctuation and the signal to noise ratio for absorption, differential, and Faraday rotation angle methods are calculated and compared. Using a Wollaston prism rotated 45°relative to the incident polarization, and two photodetectors, Ramsey fringes of three detection methods are obtained simultaneously. In the proposed scheme, the long-term Faraday rotation angle fluctuation is 0.66% at 30000s, which is much smaller than fluctuation of traditional absorption signal 3.9% at 30000s. And the contribution of laser intensity noise to clock instability is also reduced. Using optimized photodetector with high common mode rejection ratio, a better performance should be expected. This proposed scheme is attractive for the development of high performance vapor clock based on pulsed optically pumped.

Flexible ferroelasticity in monolayer PdS2: a DFT study.

As an unusual mechanical response, the ferroelastic phenomenon in two-dimensional materials has been reported both experimentally and theoretically in recent years. Here, we present the theoretical findings of ferroelastic switching in monolayer PdS2. We demonstrate four types of PdS2 allotropes, showing excellent ferroelasticity with low ferroelastic barriers and strong switching signals. The ferroelastic transitions in monolayer PdS2 include the lattice rotation in penta-α PdS2, the transformation between penta-α PdS2 and penta-ß PdS2, the transformation between penta-α PdS2 and penta-γ PdS2, the transformation between penta-ß PdS2 and penta-γ PdS2, the transformation between penta-α PdS2 and δ PdS2, and the lattice rotation in δ PdS2. The ferroelastic transitions between these four allotropes have revealed the flexible ferroelasticity in monolayer PdS2. Specifically, the flexible switching in PdS2 allotropes may efficiently control the anisotropic transport of electrons. Thus, the presence of these outstanding mechanical properties endows PdS2 with great potential for applications in next-generation shape memory devices.

Double ring nanostructure with an internal cavity and a multiple Fano resonances system for refractive index sensing.

A novel nanosensor based on a metal-insulator-metal waveguide coupled to a double ring resonator is proposed. The spectral characteristics are studied by finite element method, and a Fano resonance (FR) formed by the interference of the narrowband mode and the broadband mode is discovered. After analyzing the effects of structural parameters on the transmission characteristics, the structure is further optimized by adding a rectangular cavity inside the ring cavity. The maximum sensitivity reaches 1885 nm/RIU with the figure of merit (FOM) of 77. Additionally, a tunable multiple FR system is realized through the derivative structure, which leads to the splitting of the resonance mode and produces two new narrowband modes. Their formation mechanism and performance are studied through a normalized magnetic field distribution and transmission spectrum. The designed structure with excellent performance can discover significant applications in the future nanosensing domain.

A Nanostructure with Defect Based on Fano Resonance for Application on Refractive-Index and Temperature Sensing.

Herein, a nanosensor structure is proposed, which comprises metal-insulator-metal (MIM) waveguide with stub and circular ring cavity with a stub (CRCS). The phenomenon of Fano resonance appears in the transmission spectrum, which is formed by interaction between the narrowband mode of CRCS and broadband mode of stub on bus waveguide. The influence of geometric asymmetry on mode splitting of Fano resonance was discussed. The mode splitting of Fano resonance can vastly improve figure of merit (FOM) with a sight decrease of sensitivity. The best performance of the refractive-index nanosensor is attained, which is 1420 nm/RIU with a high FOM of 76.76. Additionally, the application of designed structure on temperature sensing was investigated, which has sensitivity of 0.8 nm/°C. The proposed structure also possesses potential applications on other on-chip nanosensors.

Fano Resonance in an Asymmetric MIM Waveguide Structure and Its Application in a Refractive Index Nanosensor.

Herein, the design for a tunable plasmonic refractive index nanosensor is presented. The sensor is composed of a metal⁻insulator⁻metal waveguide with a baffle and a circular split-ring resonator cavity. Analysis of transmission characteristics of the sensor structures was performed using the finite element method, and the influence of the structure parameters on the sensing characteristics of the sensor is studied in detail. The calculation results show that the structure can realize dual Fano resonance, and the structural parameters of the sensor have different effects on Fano resonance. The peak position and the line shape of the resonance can be adjusted by altering the sensitive parameters. The maximum value of structural sensitivity was found to be 1114.3 nm/RIU, with a figure of merit of 55.71. The results indicate that the proposed structure can be applied to optical integrated circuits, particularly in high sensitivity nanosensors.

Fano Resonance in a MIM Waveguide with Two Triangle Stubs Coupled with a Split-Ring Nanocavity for Sensing Application.

Herein, a compact refractive index nanosensor comprising a metal- insulator- metal (MIM) waveguide with symmetric two triangle stubs coupled with a circular split-ring resonance cavity (CSRRC) is theoretically presented. An analysis of the propagation characteristics of the designed structure is discussed employing the finite element method (FEM). The calculation results revealed that a Fano resonance outline emerged, which results from an interaction between the continuous broadband state of the waveguide with two symmetric triangle stubs and the discrete narrowband state of the CSRRC. The influence of geometric parameters on sensing properties was studied in detail. The maximum sensitivity reached 1500 nm/RIU with a high figure of merit of 65.2. The presented structure has great applications for on-chip plasmonic nanosensors.

Tunable Fano Resonance in Asymmetric MIM Waveguide Structure.

A plasmonic waveguide coupled system that uses a metal-insulator-metal (MIM) waveguide with two silver baffles and a coupled ring cavity is proposed in this study. The transmission properties of the plasmonic system were investigated using the finite element method. The simulation results show a Fano profile in the transmission spectrum, which was caused by the interaction of the broadband resonance of the Fabry-Perot (F-P) cavity and the narrow band resonance of the ring cavity. The Fabry-Perot (F-P) cavity in this case was formed by two silver baffles dividing the MIM waveguide. The maximum sensitivity of 718 nm/RIU and the maximum figure of merit of 4354 were achieved. Furthermore, the effects of the structural parameters of the F-P cavity and the ring cavity on the transmission properties of the plasmonic system were analyzed. The results can provide a guide for designing highly sensitive on-chip sensors based on surface plasmon polaritons.

Refractive Index Sensor Based on Fano Resonances in Metal-Insulator-Metal Waveguides Coupled with Resonators.

A surface plasmon polariton refractive index sensor based on Fano resonances in metal-insulator-metal (MIM) waveguides coupled with rectangular and ring resonators is proposed and numerically investigated using a finite element method. Fano resonances are observed in the transmission spectra, which result from the coupling between the narrow-band spectral response in the ring resonator and the broadband spectral response in the rectangular resonator. Results are analyzed using coupled-mode theory based on transmission line theory. The coupled mode theory is employed to explain the Fano resonance effect, and the analytical result is in good agreement with the simulation result. The results show that with an increase in the refractive index of the fill dielectric material in the slot of the system, the Fano resonance peak exhibits a remarkable red shift, and the highest value of sensitivity (S) is 1125 nm/RIU, RIU means refractive index unit. Furthermore, the coupled MIM waveguide structure can be integrated with other photonic devices at the chip scale. The results can provide a guide for future applications of this structure.

Refractive Index Sensor Based on a Metal-Insulator-Metal Waveguide Coupled with a Symmetric Structure.

In this study, a new refractive index sensor based on a metal-insulator-metal waveguide coupled with a notched ring resonator and stub is designed. The finite element method is used to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the broadband spectrum and narrowband spectrum. In the design, the broadband spectrum signal is generated by the stub, while the narrowband spectrum signal is generated by the notched ring resonator. In addition, the structural parameters of the resonators and the structure filled with media of different refractive indices are varied to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

Fano Resonance Based on Metal-Insulator-Metal Waveguide-Coupled Double Rectangular Cavities for Plasmonic Nanosensors.

A refractive index sensor based on metal-insulator-metal (MIM) waveguides coupled double rectangular cavities is proposed and investigated numerically using the finite element method (FEM). The transmission properties and refractive index sensitivity of various configurations of the sensor are systematically investigated. An asymmetric Fano resonance lineshape is observed in the transmission spectra of the sensor, which is induced by the interference between a broad resonance mode in one rectangular and a narrow one in the other. The effect of various structural parameters on the Fano resonance and the refractive index sensitivity of the system based on Fano resonance is investigated. The proposed plasmonic refractive index sensor shows a maximum sensitivity of 596 nm/RIU.

A Refractive Index Sensor Based on a Metal-Insulator-Metal Waveguide-Coupled Ring Resonator.

A refractive index sensor composed of two straight metal-insulator-metal waveguides and a ring resonator is presented. One end of each straight waveguide is sealed and the other end acts as port. The transmission spectrum and magnetic field distribution of this sensor structure are simulated using finite-difference time-domain method (FDTD). The results show that an asymmetric line shape is observed in the transmission spectrum, and that the transmission spectrum shows a filter-like behavior. The quality factor and sensitivity are taken to characterize its sensing performance and filter properties. How structural parameters affect the sensing performance and filter properties is also studied.

Improved Energy Storage Performance of Composite Films Based on Linear/Ferroelectric Polarization Characteristics.

The development and integration of high-performance electronic devices are critical in advancing energy storage with dielectric capacitors. Poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (PVTC), as an energy storage polymer, exhibits high-intensity polarization in low electric strength fields. However, a hysteresis effect can result in significant residual polarization, leading to a severe energy loss, which impacts the resultant energy storage density and charge/discharge efficiency. In order to modify the polarization properties of the polymer, a biaxially oriented polypropylene (BOPP) film with linear characteristics has been selected as an insulating layer and combined with the PVTC ferroelectric polarization layer to construct PVTC/BOPP bilayer films. The hetero-structure and polarization characteristics of the bilayer film have been systematically studied. Adjusting the BOPP volume content to 67% resulted in a discharge energy density of 10.1 J/cm3 and an energy storage efficiency of 80.9%. The results of this study have established the mechanism for a composite structure regulation of macroscopic energy storage performance. These findings can provide a basis for the effective application of ferroelectric polymer-based composites in dielectric energy storage.

Study on the Effect of Electron/Hole Injection on the Energy-Storage Properties of Polymer Dielectrics.

As a critical component of electrostatic capacitors, the polymer dielectric directly affects the performance of the capacitor. In this work, Polycarbonate (PC)/Polyvinylidene fluoride (PVDF) asymmetric bilayer polymer dielectrics were prepared, and the influence of different polymer materials' barrier characteristics on various electrical properties of composite dielectrics was studied by changing the direction of applied electric fields. Research has found that the dielectric constant of a composite dielectric is between PVDF and PC (approximately 4.8 at 10 Hz) and is independent of the relative position of PVDF and PC in the dielectric. However, the relative position of PC and PVDF has a significant impact on the energy-storage characteristics of composite dielectrics. When PVDF comes into contact with the negative electrode, even though PC has a higher hole barrier, the composite dielectric can only withstand a maximum electric-field strength of 400 MV/m, which is much lower than the maximum electric-field strength that pure PC can withstand (520 MV/m), and it only achieves an energy-storage density of 3.7 J/cm3. When the PC comes into contact with the negative electrode, the high electron barrier of the PC effectively suppresses the injection of electrons at the electrode. It can withstand the same electric-field strength as PC (520 MV/m), achieving an energy-storage density of 5.48 J/cm3, which is 1.46 times that of pure PC and 1.64 times that of PVDF. This experiment effectively combined the advantages of PC and PVDF by utilizing the electron/hole barrier of polymer materials to obtain a fully organic dielectric with excellent energy-storage performance.

Highly Sensitive Plasmon Refractive Index Sensor Based on MIM Waveguide.

This paper introduces a novel plasmon refractive index nanosensor structure based on Fano resonance. The structure comprises a metal-insulator-metal (MIM) waveguide with an inverted rectangular cavity and a circle minus a small internal circle plus a rectangular cavity (CMSICPRC). This study employs the finite element method (FEM) to analyze the sensing characteristics of the structure. The results demonstrate that the geometrical parameters of specific structures exert a considerable influence on the sensing characteristics. Simulated experimental data show that the maximum sensitivity of this structure is 3240 nm/RIU, with a figure of merit (FOM) of 52.25. Additionally, the sensor can be used in biology, for example, to detect the concentration of hemoglobin in blood. The sensitivity of the sensor in this application, according to our calculations, can be 0.82 nm∙g/L.

Identification of near-infrared characteristic bands of small bowel necrosis based on cellwise detection algorithm.

The near-infrared spectroscopy is often used to distinguish small bowel necrosis due to necrotizing enterocolitis (NEC). The characteristic bands of small bowel necrosis, as an important basis for evaluating the confidence of the differentiation results, are challenging to identify quickly. In this study, we proposed to identify characteristic bands of lesion samples based on hyperspectral imaging (HSI) and cellwise outlier detection. Rabbits were used as an animal model to simulate the clinical symptoms of NEC. The rabbits were detected at intervals of 10, 30, 60, and 90 min. The characteristic bands were identified within the same rabbit, between different rabbits and at different times. The result showed the bands near 763 nm, corresponding to the absorption peak of deoxyhemoglobin, were the characteristic bands separating samples with NEC. The identification result was plausible because hypoxia was the main cause of NEC. The method was easy to perform.

Nanorefractive index transducer using a ring cavity with an internal h-shaped cavity grounded on Fano resonance.

Building on the Fano resonance observation, a new refractive index transducer structure at the nanoscale is proposed in this article, which is a refractive index transducer consisting of a metal-insulator-metal (MIM) waveguide structure coupled with a ring cavity internally connected to an h-shaped structure (RCIhS). Using an analytical method based on COMSOL software and finite element method (FEM), the effect of different geometric parameters of the structure on the trans-mission characteristics of the system is simulated and analyzed, which in turn illustrates the effect of the structural parameters on the output Fano curves. As simulation results show, the internally connected h-shaped structure is an influential component in the Fano resonance. By optimizing the geometrical parameters of the structure, the system finally accomplishes a sensitivity (S) of 2400 nm/RIU and a figure of merit (FOM) of 68.57. The sensor has also been demonstrated in the realm of temperature detection, having tremendous potential for utilization in future nano-sensing and optically integrated systems.

Refractive Index Sensor Based on a Metal-Insulator-Metal Bus Waveguide Coupled with a U-Shaped Ring Resonator.

In this study, a novel refractive index sensor structure was designed consisting of a metal-insulator-metal (MIM) waveguide with two rectangular baffles and a U-Shaped Ring Resonator (USRR). The finite element method was used to theoretically investigate the sensor's transmission characteristics. The simulation results show that Fano resonance is a sharp asymmetric resonance generated by the interaction between the discrete narrow-band mode and the successive wide-band mode. Next, the formation of broadband and narrowband is further studied, and finally the key factors affecting the performance of the sensor are obtained. The best sensitivity of this refractive-index sensor is 2020 nm/RIU and the figure of merit (FOM) is 53.16. The presented sensor has the potential to be useful in nanophotonic sensing applications.

High-Property Refractive Index and Bio-Sensing Dual-Purpose Sensor Based on SPPs.

A high-property plasma resonance-sensor structure consisting of two metal-insulator-metal (MIM) waveguides coupled with a transverse ladder-shaped nano-cavity (TLSNC) is designed based on surface plasmon polaritons. Its transmission characteristics are analyzed using multimode interference coupling mode theory (MICMT), and are simulated using finite element analysis (FEA). Meanwhile, the influence of different structural arguments on the performance of the structure is investigated. This study shows that the system presents four high-quality formants in the transmission spectrum. The highest sensitivity is 3000 nm/RIU with a high FOM* of 9.7 × 105. In addition, the proposed structure could act as a biosensor to detect the concentrations of sodium ions (Na+), potassium ions (K+), and the glucose solution with maximum sensitivities of 0.45, 0.625 and 5.5 nm/mgdL-1, respectively. Compared with other structures, the designed system has the advantages of a simple construction, a wide working band range, high reliability and easy nano-scale integration, providing a high-performance cavity choice for refractive index sensing and biosensing devices based on surface plasmons.