ABSTRACT
Heterogeneous element doping in amorphous carbon films can reduce residual stresses and improve plastic deformation. Nevertheless, the effects of dopant content and size on the metastable transition mechanism between sp2-C and sp3-C atoms during the deformation process are unclear and difficult to be in situ observed and researched, experimentally. In this work, the mechanical properties and the structural evolution during the nanoindentation of amorphous CoCrFeNi sphere-doped carbon heterostructured films with different radii were simulated. The results indicate that the hardness H and elastic modulus E of the films decreased with the increase of the dopant addition. H decreases from 50.69 to 28.94 GPa, and E decreases from 664.39 to 448.62 GPa. The decrease in the elastic recovery and the enlargement of the shear transition zones indicate that the presence of the amorphous CoCrFeNi dopant can significantly improve the plastic deformation capacity of the films. During the nanoindentation process, the spherical dopants reduce the stress and shear strain of the regions under the indenter in a-C films. The reduction of compressive and shear stresses in the film can inhibit the C atom metastable transition from sp2-C to sp3-C. This can provide a theoretical basis for the development and design of heavy-load and high-deformation-rate a-C films.
ABSTRACT
Physicochemical and toxicological characterization of leather tanning wastewater has been widely documented. However, few reports have examined the response of denitrification N2 and N2O emissions in riparian sediments of tannery wastewater-receiving rivers. In this study, 15N-nitrate labeling was used to reveal the effects of tanning wastewater on denitrification N2 and N2O emission in a wastewater-receiving river (the old Mang River, OMR). OMR riparian sediments were highly polluted with total organic carbon (93.39 mg/kg), total nitrogen (5.00 g/kg) and heavy metals; specifically, Cr, Zn, Cd, and Pb were found at concentrations 47.3, 5.8, 1.6, 4.3, and 2.8 times that in a nearby parallel river without tanning wastewater input (the new Mang River, NMR), respectively. The denitrification N2 emission rates (0.0015 nmol N · g-1 h-1) of OMR riparian sediments were significantly reduced by 2.5 times compared with those from the NMR (p < 0.05), but the N2O emission rates (0.31 nmol N · g-1 h-1) were significantly increased (4.1 times, p < 0.05). Although the dominant nitrogen-transforming bacteria phylum was Proteobacteria in the riparian sediments of both rivers, 11 nitrogen-transforming bacteria genera in the OMR were found to be significantly enriched; five of these were related to pollutant degradation based on linear discriminant analysis (LDA >3). The average activity of the electron transport system in the OMR was 6.3 times lower than that of the NMR (p < 0.05). Among pollution factors, heavy metal complex pollution was the dominant factor driving variations in N2O emissions, microbial community structure, and electron transport system activity. These results provide a new understanding and reference for the treatment of tanning wastewater-receiving rivers.
ABSTRACT
Microorganisms have developed mechanisms to adapt to environmental stress, but how microbial communities adapt to long-term and combined heavy-metal contamination under natural environmental conditions remains unclear. Specifically, this study analyzed the characteristics of heavy metal composition, microbial community, and heavy metal resistance genes (MRGs) in sediments along Mang River, a tributary of the Yellow River, which has been heavily polluted by industrial production for more than 40 years. The results showed that the concentrations of Cr, Zn, Pb, Cu and As in most sediments were higher than the ambient background values. Bringing the heavy metals speciation and concentration into the risk evaluation method, two-thirds of the sediment samples were at or above the moderate risk level, and the ecological risk of combined heavy metals in the sediments decreased along the river stream. The high ecological risk of heavy metals affected the microbial community structure, metabolic pathways and MRG distribution. The formation of a HM-resistant microbiome possibly occurred through the spread of insertion sequences (ISs) carrying multiple MRGs, the types of ISs carrying MRGs outnumber those of plasmids, and the quantity of MRGs on ISs is also higher than that on plasmids. These findings could improve our understanding of the adaptation mechanism of microbial communities to long-term combined heavy metal contamination.
Subject(s)
Geologic Sediments , Metals, Heavy , Microbiota , Rivers , Water Pollutants, Chemical , Metals, Heavy/toxicity , Metals, Heavy/analysis , Geologic Sediments/microbiology , Geologic Sediments/chemistry , Rivers/microbiology , Rivers/chemistry , Microbiota/drug effects , Water Pollutants, Chemical/analysis , Water Pollutants, Chemical/toxicity , China , Environmental Monitoring , Bacteria/genetics , Bacteria/drug effectsABSTRACT
Dioscorea opposita cultivar Tiegun is an economically important crop with high nutritional and medicinal value. Plants can activate complex and diverse defense mechanisms after infection by pathogenic fungi. Moreover, endophytic fungi can also trigger the plant immune system to resist pathogen invasion. However, the study of the effects of endophytic fungi on plant infection lags far behind that of pathogenic fungi, and the underlying mechanism is not fully understood. Here, the black spot pathogen Alternaria alternata and the endophytic fungus Penicillium halotolerans of Tiegun were identified and used to infect calli. The results showed that A. alternata could cause more severe membrane lipid peroxidation, whereas P. halotolerans could rapidly increase the activity of the plant antioxidant enzymes superoxide dismutase, peroxidase, and catalase; thus, the degree of damage to the callus caused by P. halotolerans was weaker than that caused by A. alternata. RNA sequencing analysis revealed that various plant defense pathways, such as phenylpropanoid biosynthesis, flavonoid biosynthesis, plant hormone signal transduction, and the mitogen-activated protein kinase signaling pathway, play important roles in triggering the plant immune response during fungal infection. Furthermore, the tryptophan metabolism, betalain biosynthesis, fatty acid degradation, flavonoid biosynthesis, tyrosine metabolism, and isoquinoline alkaloid biosynthesis pathways may accelerate the infection of pathogenic fungi, and the ribosome biogenesis pathway in eukaryotes may retard the damage caused by endophytic fungi. This study lays a foundation for exploring the infection mechanism of yam pathogens and endophytic fungi and provides insight for effective fungal disease control in agriculture.
Subject(s)
Alternaria , Dioscorea , Endophytes , Plant Diseases , Dioscorea/microbiology , Dioscorea/genetics , Alternaria/physiology , Alternaria/pathogenicity , Plant Diseases/microbiology , Plant Diseases/immunology , Endophytes/physiology , Endophytes/genetics , Penicillium/genetics , Penicillium/physiology , Penicillium/pathogenicity , Gene Expression Profiling , Gene Expression Regulation, Plant , TranscriptomeABSTRACT
Yam is an important medicinal and edible dual-purpose plant with high economic value. However, nematode damage severely affects its yield and quality. One of the major effects of nematode infestations is the secondary infection of pathogenic bacteria or fungi through entry wounds made by the nematodes. Understanding the response of the symbiotic microbial community of yam plants to nematodes is crucial for controlling such a disease. In this study, we investigated the rhizosphere and how endophytic microbiomes shift after nematode infection during the tuber expansion stage in the Dioscorea opposita Thunb. cultivar Tiegun. Our results revealed that soil depth affected the abundance of nematodes, and the relative number of Meloidogyne incognita was higher in the diseased soil at a depth of 16 to 40 cm than those at a depth of 0 to 15 and 41 to 70 cm. The abundance of and interactions among soil microbiota members were significantly correlated with root-knot nematode (RKN) parasitism at various soil depths. However, the comparison of the microbial α-diversity and composition between healthy and diseased rhizosphere soil showed no difference. Compared with healthy soils, the co-occurrence networks of M. incognita-infested soils included a higher ratio of positive correlations linked to plant health. In addition, we detected a higher abundance of certain taxonomic groups belonging to Chitinophagaceae and Xanthobacteraceae in the rhizosphere of RKN-infested plants. The nematodes, besides causing direct damage to plants, also possess the ability to act synergistically with other pathogens, especially Ramicandelaber and Fusarium, leading to the development of disease complexes. In contrast to soil samples, RKN parasitism specifically had a significant effect on the composition and assembly of the root endophytic microbiota. The RKN colonization impacted a wide variety of endophytic microbiomes, including Pseudomonas, Sphingomonas, Rhizobium, Neocosmospora, and Fusarium. This study revealed the relationship between RKN disease and changes in the rhizosphere and endophytic microbial community, which may provide novel insights that help improve biological management of yam RKNs.
Subject(s)
Dioscorea , Microbiota , Plant Diseases , Plant Roots , Rhizosphere , Soil Microbiology , Symbiosis , Tylenchoidea , Animals , Dioscorea/microbiology , Dioscorea/parasitology , Plant Roots/microbiology , Plant Roots/parasitology , Plant Diseases/parasitology , Plant Diseases/microbiology , Tylenchoidea/physiology , Bacteria/classification , Bacteria/genetics , Bacteria/isolation & purification , Nematoda/physiology , Nematoda/microbiologyABSTRACT
BBX proteins play important roles in all of the major light-regulated developmental processes. However, no systematic analysis of BBX gene family regarding the regulation of photoperiodic microtuber formation has been previously performed in yam. In this study, a systematic analysis on the BBX gene family was conducted in three yam species, with the results, indicating that this gene plays a role in regulating photoperiodic microtuber formation. These analyses included identification the BBX gene family in three yam species, their evolutionary relationships, conserved domains, motifs, gene structure, cis-acting elements, and expressional patterns. Based on these analyses, DoBBX2/DoCOL5 and DoBBX8/DoCOL8 showing the most opposite pattern of expression during microtuber formation were selected as candidate genes for further investigation. Gene expression analysis showed DoBBX2/DoCOL5 and DoBBX8/DoCOL8 were highest expressed in leaves and exhibited photoperiod responsive expression patterns. Besides, the overexpression of DoBBX2/DoCOL5 and DoBBX8/DoCOL8 in potato accelerated tuber formation under short-day (SD) conditions, whereas only the overexpression of DoBBX8/DoCOL8 enhanced the accelerating effect of dark conditions on tuber induction. Tuber number was increased in DoBBX8/DoCOL8 overexpressing plants under dark, as well as in DoBBX2/DoCOL5 overexpressing plants under SD. Overall, the data generated in this study may form the basis of future functional characterizations of BBX genes in yam, especially regarding their regulation of microtuber formation via the photoperiodic response pathway.
Subject(s)
Dioscorea , Dioscorea/genetics , Dioscorea/metabolism , Gene Expression Profiling , Multigene Family , Photoperiod , Circadian Rhythm , Gene Expression Regulation, Plant , Plant Proteins/metabolismABSTRACT
Diamond tools play a vital role in precision machining. However, the adhesive wear restricts their application when Fe-based workpieces are cut by diamond tools. Thus, it is significant to theoretically explain the interface binding mechanism between the diamond and Fe alloy matrix. In this study, the adhesion and friction behaviors of a γ-Fe/diamond (denoted as Fe/C) heterogeneous contact interface were investigated employing density functional theory (DFT). The results show that the transfer of the Fe atom to C atom occurs when the interaction energy for a given configuration is larger than the separation energy of the corresponding Fe surface layers. The energy barriers of the Fe/C(100), (110) and (111) sliding interfaces along the minimum energy path are 1.45, 0.48 and 0.42 J m-2, respectively, indicating that the Fe/C(111) interface is the easiest to slide. Furthermore, the friction potential barrier increases with an increase in the load (1-5 nN) according to the potential energy curves. Moreover, the friction coefficient of the Fe/C interface is larger than 0.2 and provides a theoretical minimum friction coefficient for the Fe/C sliding interface.
ABSTRACT
Dioscorea opposita is an annual twining plant in China that is used for consumption and medicinal purposes. The planting area of D. opposita is near 500,000 hectares in China, mainly in Shangdong, Hebei, Henan, Jiangxi and Yunnan provinces. In August 2021, we observed that some D. opposita plants grew poorly with smaller and chlorotic leaves in Changyuan (35°8'12"N; 114°43'52"E), Henan Province, China. Galls with hook-shaped roots and tuber damage were also observed, typical of root-knot nematode. Thirty tubers were randomly collected and 60% were infested with root-knot nematodes. During a disease survey in Changyuan, the incidences of root-knot nematode damage were 31.5%, 21%, and 18% in three fields (0.33, 0.67, and 4 ha, respectively) at harvest. The average tuber length of infected plants was decreased by 65.8%, and the average weight was decreased by 70.1% compared to the healthy plants. Males, females, second-stage juveniles (J2s), and eggs were extracted from individual diseased tubers from the three fields for morphological identification. Females were white, pear-shaped with a projecting neck. Males showed a trapezoidal labial region with prominent stylet knobs, including a high head cap which had a stepped outline and was centrally concave in lateral view. Morphological measurements are described in the supplementary material. All data and descriptions conformed to the morphological characteristics of Meloidogyne incognita. Genomic DNA was extracted from J2s (n=9) using PCR lysis buffer, and used for PCR amplification of the sequence characterized amplified region (SCAR) markers specific for M. incognita. Two pairs of the SCAR primers, Mi-F/Mi-R, and Inc-K14-F/Inc-K14-R, were used to diagnose whether these nematodes from D. opposita were M. incognita (Meng et al. 2004; Randig et al. 2002). The PCR produced expected amplification products of 955 and 399 bp, confirming the nematode to be M. incognita. Primers specific for M. arenaria (Far/Rar) and M. javanica (Fjav/Rjav) were used but failed to amplify fragments (Randig et al. 2002; Zijlstra et al. 2000). The obtained PCR fragments were sequenced and deposited in GenBank (accession no. OQ420602.1, OQ427638.1). They showed 99.9 and 100% identity to the available GenBank M. incognita sequence (accession no. MK410954.1, ON861825.1), respectively. A pathogenicity test was conducted in greenhouse conditions. Bulbils of D. opposita were sown in the pots filled with 2,000 ml of autoclaved soil mixture (loamy soil/sand, 1:1). One month later, 15 seedlings (five to six leaf stage) were inoculated with 1,000 M. incognita J2s individually. Five plants without nematode inoculation were used as the control. Two months after inoculation, all of the inoculated roots had galling symptoms similar to those observed in the field, and 100% of root system tissues had galls. The root gall index was ~6 according to a 0 to 10 RKN damage rating scale (Poudyal et al. 2005). No symptoms were found on the control plants. The nematodes were reisolated from root tissue and identified. M. incognita has a broad host range in many species of economic importance including Salvia miltiorrhiza (Wen et al. 2023), Ipomoea batatas (Maleita et al. 2022), and Zea mays (López-Robles et al. 2013). So far, M. incognita has been reported in D. alata and D. rotundata in Africa (Onkendi et al. 2014). To our best knowledge, this is the first record of M. incognita on D. opposita in Henan Province, China. With the increased planting area of D. opposita in China, root-knot nematodes are becoming more serious and reducing tuber production, with yield losses more than 60%. This identification is a preliminary step in developing effective disease management schemes. Declaration of interest The authors declare no conflict of interest. Funding This work was financially supported by the Key Scientific Research Projects of Higher Education Institutions of Henan Province (21A180013), China Agriculture Research System (CARS-21), The Zhongyuan high level talents special support plan-Science and Technology Innovation Leading Talents (224200510011) and Science and Technology Research Project of Henan Province (222102310211). References López-Robles, J., et al. 2013. Plant Dis. 97:694. https://doi.org/10.1094/PDIS-07-12-0674-PDN. Maleita, C., et al. 2022. Plant Dis. 106:2536. https://doi.org/10.1094/PDIS-12-21-2680-PDN. Meng, Q. P., et al. 2004. Acta Phytopathol. Sinica 34:204. https://doi.org/10.13926/j.cnki.apps.2004.03.003. Onkendi, E. M., et al. 2014. Plant Pathol. 63:727. https://doi.org/10.1111/ppa.12202. Poudyal, D. S., et al. 2005. Australas. Plant Pathol. 34:181. https://doi.org/10.1071/AP05011. Randig, O., et al. 2002. Genome 45:862. https://doi.org/10.1139/g02-054. Wen, Y., et al. 2023. Plant Dis. Accepted. https://doi.org/10.1094/PDIS-05-22-0997-PDN. Zijlstra, C., et al. 2000. Nematology 2:847. https://doi.org/10.1163/156854100750112798.
ABSTRACT
In this paper, according to the C(111) surface and Ti(112Ì 0) surface relative positions, three stacking interface models were constructed by the first-principles method, and they were defined as 1st-C(111)/Ti(112Ì 0), 2nd-C(111)/Ti(112Ì 0), and 4th-C(111)/Ti(112Ì 0), respectively. After calculation, the work of interfacial adhesion of the 1st-C(111)/Ti(112Ì 0), 2nd-C(111)/Ti(112Ì 0), and 4th-C(111)/Ti(112Ì 0) interface models is found to be 9.689, 10.246, and 9.714 J/m2, respectively, and their interface energies are observed to be 1.064, 0.507, and 1.039 J/m2, respectively. Moreover, the electronic characteristics of C(111)/Ti(112Ì 0) interfaces are dominated by polar covalent bonds, supplemented by certain metallicity. When the strain reaches 13, 15, and 12%, respectively, the maximum tensile stress values of 1st-C(111)/Ti(112Ì 0), 2nd-C(111)/Ti(112Ì 0), and 4th-C(111)/Ti(112Ì 0) interface models are observed to be 16.207, 19.183, and 17.393 GPa, respectively. After all C(111)/Ti(112Ì 0) interfaces fracture under tension, the Ti atoms of the Ti(112Ì 0) surface are transferred to the C(111) surface, indicating that the strength of Ti-C bonds at the interface is higher than the strength of Ti-Ti bonds inside the Ti(112Ì 0) surface. The maximum value of the sliding potential energy surface is 1.709 J/m2; the maximum value of the potential energy curve is 0.445 J/m2; and the ideal shear strength of the C(111)/Ti(112Ì 0) interface is 0.386 GPa. In summary, the interfacial adhesion property of the 2nd-C(111)/Ti(112Ì 0) interface is better than those of 1st-C(111)/Ti(112Ì 0) and 4th-C(111)/Ti(112Ì 0) interfaces.
ABSTRACT
BACKGROUND: Trisporic acids are considered to be key regulators of carotenoid biosynthesis and sexual reproduction in zygomycetes, but the mechanisms underlying this regulation have not been fully elucidated. RESULTS: In this study, the relationships between trisporic acids and lycopene synthesis were investigated in Blakeslea trispora. The lycopene concentration in single fermentation by the (-) strain with the addition of 24 µg/L trisporic acids was slightly higher than that observed in mated fermentation. After transcriptomic analysis, a steroid 5α-reductase-like gene, known as SR5AL in B. trispora, was first reported. 5α-Reductase inhibitors reduced lycopene biosynthesis and downregulated the expression of sex determination and carotenoid biosynthesis genes. Overexpression of the SR5AL gene upregulated these genes, regardless of whether trisporic acids were added. CONCLUSION: These findings indicated that the SR5AL gene is a key gene associated with the response to trisporic acids.
Subject(s)
Mucorales , Genes, Regulator , Lycopene/metabolism , Mucorales/genetics , Mucorales/metabolism , Oxidoreductases/metabolismABSTRACT
A tetragonal C4N (t-C4N) structure was predicted via CALYPSO code, and the effects of pressure on its structural and mechanical properties were studied. The results show that t-C4N is different from various 2D CxNy compounds with a new type 3D crystal structure, which is similar to diamond. Bulk t-C4N is equipped with excellent elastic properties. When the pressure is increased from 0 GPa to 350 GPa, its bulk modulus B, shear modulus G and Young's modulus E are increased from 426.9 GPa to 1123.1 GPa, 371.4 GPa to 582.9 GPa and 863.7 GPa to 1490.9 GPa, respectively. The anisotropic Bmax, Gmax and Emax are increased from 582.38 GPa to 1751.41 GPa, 478.29 GPa to 1033.97 GPa and 1281.26 GPa to 2490.14 GPa, respectively. When the pressure is 0 GPa, the hardness calculated by Chen's and Tian's models are 51.15 GPa and 51.81 GPa, respectively. Its ideal tensile strength in [111] orientation is the smallest (63.46 GPa), which indicates that the (111) planes allow easy cleavage. The smallest ideal shear strength (67.98 GPa) can be obtained in the (111)[11Ì0] orientation, which suggests its theoretical hardness is about 67.98 GPa. Due to its excellent mechanical properties, t-C4N can be used as an industrial superhard material.
ABSTRACT
Composting is an effective and necessary modality in the recycling of agricultural wastes such as livestock manure, furfural, and straw. However, the risks of heavy metals (HMs) and antibiotic resistance genes (ARGs) during industrial-scale composting process have not been adequately assessed, especially with the addition of bacterial agents. In this study, changes in HMs toxicity, ARGs propagation and microbial community structure during industrial-scale aerobic composting of livestock manure were firstly investigated with various substrates addition. Moreover, the effect of the addition of bacterial agents (Bacillus strains) was evaluated. The results showed that industrial aerobic composting process could immobilize various HMs with different extents and significantly reduce the levels of ARGs such as intl1 and oqxB genes. The addition of Bacillus strains could further reduce the levels of most detected ARGs and the bioavailability of Cu and Cr, and the relative abundance of ereA and tetA was undetectable in some materials. After composting, the main bacterial community structures were similar among different substrates irrespective of bacterial agents and indicated that the composting process was the main driver for their change. This study provides a scientific reference for the safe reuse of livestock manure.
Subject(s)
Composting , Metals, Heavy , Animals , Anti-Bacterial Agents , Composting/methods , Genes, Bacterial , Livestock , Manure/microbiology , Metals, Heavy/toxicityABSTRACT
In this paper, C and Ti were used as the deposition atoms in the molecular dynamics model. The effects of Ti doping percentages (2, 8, 14, and 20 atom %) on the structure and internal stress of a-C films were investigated. The results showed that with the increase in the Ti percentage, the density of the intrinsic zone is gradually increased, while the growth rate is slowly decreased. The internal stress is gradually changed from compressive stress to tensile stress. Among them, when the Ti percentage is 14 atom %, the internal stress is closer to 0. The C percentage with sp3 hybridization is decreased, while those with sp2 and sp hybridizations are increased. The positions of the first and second peaks in the RDF were shifted to the left. Moreover, the distribution of bond lengths and bond angles in the intrinsic zone tend to change from diamond to graphite, which proves that Ti doping leads to the graphitization of a-C films. In addition, Ti doping affects the internal stress of a-C films by changing the C percentage with sp3 hybridization in them.
ABSTRACT
With the development of the aerospace industry, the requirement for mechanical parts, which are serviced under extreme conditions such as high temperature, is more and more severe. Amorphous carbon (a-C) films are widely used in the aviation field as a protective coating because of their excellent antiwear and friction-reduction properties. However, a-C films are vulnerable to failure in a high-temperature environment, and a series of complex changes in the friction process make it a challenge to put forward the friction mechanism. Here, the sliding friction behaviors of amorphous carbon (a-C) films at different simulated temperatures (STs) (300-1300 K) were analyzed by molecular dynamics. The density, average coordination number, and local residual stress as well as the hybridization of sp, sp2, and sp3 of a-C films were analyzed to reveal the high-temperature sliding friction mechanism of a-C films. The results show that the friction coefficient (µ) of a-C films increased with increase in ST. Meanwhile, the friction mechanisms of a-C films are different at an ST lower than 800 K and higher than 1100 K. Compared with those before sliding, the local residual stress of all a-C films is relaxed, which causes transformation of sp3 into sp2. Moreover, when ST is lower than 800 K, the µ increased with increase in sp3%. When ST is higher than 1100 K, the stability of a-C films is broken, which results in the rapid increase in µ.
ABSTRACT
Recently, the microbial degradation of tetracycline has been widely reported. However, its potential risks in treating wastewater containing high concentrations of tetracycline have not been fully evaluated. In this study, the evolution of the microbial community and drug resistance was traced during the enrichment of tetracycline-degrading bacteria. The results showed that some minor compositions such as Shewanella, Bacillus, and Pseudomonas in the seed sludge became the predominant genera in the enrichment cultures when continuously using tetracycline as the sole carbon source, especially some possible pathogenic bacteria increased significantly in this process. The abundances of most TRGs/16S rDNA were increased after enrichment, although the relative abundance of tetA and tetL genes decreased to some extent. From the enrichment culture, 7 predominant tetracycline-degrading strains were isolated, of which TD-1 (Bacillus) and TD-5 (Shewanella) presented high degradation efficiencies (6-day degradation rate > 95%, half-life period of tetracycline ≈ 24â¯h). In addition, multiple TRGs, mobile genetic elements (MGEs) and even gene cassettes were found in each tetracycline-degrading isolate. The findings suggested that some risks such as the pathogenicity of isolates and the spread of ARGs should be considered when the biodegradation method is used to treat wastewater polluted with high concentrations of tetracycline.
Subject(s)
Anti-Bacterial Agents/metabolism , Bacteria/metabolism , Microbiota , Tetracycline/metabolism , Bacteria/genetics , Bacteria/isolation & purification , Biodegradation, Environmental , Genes, Bacterial , Tetracycline Resistance/genetics , Wastewater/microbiologyABSTRACT
High-entropy alloy (HEA) offers great flexibility in materials design with 3-5 principal elements and a range of unique advantages such as good microstructure stability, mechanical strength over a broad range of temperatures and corrosion resistance, etc. Welding of high entropy alloy, as a key joining method, is an important emerging area with significant potential impact to future application-oriented research and technological developments in HEAs. The selection of feasible welding processes with optimized parameters is essential to enhance the applications of HEAs. However, the structure of the welded joints varies with material systems, welding methods and parameters. A systemic understanding of the structures and properties of the weldment is directly relevant to the application of HEAs as well as managing the effect of welding on situations such as corrosion that are known to be a service life limiting factor of welded structures in conditions such as marine environments. In this paper, key recent work on welding of HEAs is reviewed in detail focusing on the research of main HEA systems when applying different welding techniques. The experimental details including sample preparation, sample size (thickness) and welding conditions reflecting energy input are summarized and key issues are highlighted. The microstructures and properties of different welding zones, in particular the fusion zone (FZ) and the heat affected zones (HAZ), formed with different welding methods are compared and presented in details and the structure-property relationships are discussed. The work shows that the weldability of HEAs varies with the HEA composition groups and the welding method employed. Arc and laser welding of AlCoCrFeNi HEAs results in lower hardness in the FZ and HAZ and reduced overall strength. Friction stir welding results in higher hardness in the FZ and achieves comparable/higher strength of the welded joints in tensile tests. The welded HEAs are capable of maintaining a reasonable proportion of the ductility. The key structure changes including element distribution, the volume fraction of face centered cubic (FCC) and body centered cubic (BCC) phase as well as reported changes in the lattice constants are summarized and analyzed. Detailed mechanisms governing the mechanical properties including the grain size-property/hardness relationship in the form of Hall-Petch (H-P) effect for both bulk and welded structure of HEAs are compared. Finally, future challenges and main areas to research are highlighted.
ABSTRACT
In this study a laboratory-scale sequencing batch bioreactor was constructed, using phenanthrene/pyrene as the sole carbon-source, to demonstrate the removal efficiencies of polycyclic aromatic hydrocarbons (PAHs) and the evolution process of a functional bacterial community. The removal rates were: COD, 51.4 to 76.3%; phenanthrene, 63.5 to 92.4%; and pyrene, 65.9 to 90.1%. Quantification analysis indicated that in sludge samples from the phenanthrene/pyrene degradation stage, the contents of 16S rRNA and ring-hydroxylating dioxygenase genes of Gram-positive and Gram-negative bacteria were 10-and 72-, 102- and 1152-, 31- and 905-fold higher, respectively, than those in seed sludge samples. Clone sequencing and evolution analysis showed that genera Comamonas, Pseudomonas, and Mycobacterium were distributed across all samples and were significant PAH-degrading populations, but some genera, such as Polaromonas and Nocardioides, were substantially enriched only when phenanthrene/pyrene was fed. Correspondingly, the functional genes nidA3, phnAc, and ndoC2 were distributed across all samples, whereas nagAc, pdoA2, and pdoA were enriched only when phenanthrene/pyrene was fed.
Subject(s)
Bacteria/genetics , Bacteria/metabolism , Bioreactors , Polycyclic Aromatic Hydrocarbons/metabolism , Water Pollutants, Chemical/metabolism , DNA, Bacterial/genetics , Evolution, Molecular , Phylogeny , Polycyclic Aromatic Hydrocarbons/chemistry , RNA, Bacterial/genetics , RNA, Ribosomal/genetics , Time Factors , Water Pollutants, Chemical/chemistryABSTRACT
Five new isomorphic coordination polymers of the Co(II) ion, namely, {[Co2L(bpy)0.5(H2O)2]·2H2O}n (1), {[Co2L(pbyb)0.5(H2O)2]·3H2O}n (2), {[Co2L(dpe)0.5(H2O)2]·2H2O}n (3), {[Co2L(dpa)0.5(H2O)2]·2.5H2O}n (4), and {[Co2L(dip)0.5(H2O)2]·3.5H2O}n (5) (H4L = cis,cis,cis,cis-1,2,3,4-cyclopentaneteracarboxylic acid, bpy = 4,4'-bipyridine, pbyb = 1,4-di(pyridine-4-yl)benzene, dpe = 1,2-di(pyridine-4-yl)ethane, dpa = (E)-1,2-di(pyridin-4-yl)diazene, and dip = 1,4-di(1H-imidazol-1-yl)benzene), have been synthesized under hydrothermal conditions. The L(4-) ligand maintains its original conformation of SSRR in all of these compounds, but {Co5L}n clusters show mirror coordination symmetry in 1, 2, and 4 while the clusters in 3 and 5 do not. The addition of different N-ligands can tune the distance between {Co2L}n layers and change the pore structures of the frameworks. Magnetic susceptibility measurements indicate that 1-5 exhibit antiferromagnetic behavior.
ABSTRACT
Through livestock manure fertilization, antibiotics, antibiotic-resistant bacteria and genes are transferred to agricultural soils, resulting in a high prevalence of antibiotic-resistant bacteria in the soil. It is not clear, however, whether a correlation exists between resistant bacterial populations in manure and manure-amended soil. In this work, we demonstrate that the prevalence of cephalexin-, amoxicillin-, kanamycin- and gentamicin-resistant bacteria as well as bacteria simultaneously resistant to all four antibiotics was much higher in manure-amended soils than in manure-free soil. 454-pyrosequencing indicated that the ARB and multiple antibiotic-resistant bacteria (MARB) in swine or chicken manure and manure-amended soil were mainly distributed among Sphingobacterium, Myroides, Enterococcus, Comamonas and unclassified Flavobacteriaceae. The genus Sphingobacterium was highly prevalent among ARB from swine manure and manure-amended soil, and was also the most dominant genus among MARB from chicken manure and manure-amended soil. Other dominant genera among ARB or MARB populations in manure samples, including Myroides, Enterococcus and Comamonas, could not be detected or were detected at very low relative abundance in manure-amended soil. The present study suggests the possibility of transfer of ARBs from livestock manures to soils and persistence of ARB in these environments.
Subject(s)
Bacteria/isolation & purification , Drug Resistance, Multiple, Bacterial , Manure/microbiology , Soil Microbiology , Animals , Bacteria/genetics , Chickens/microbiology , China , Colony Count, Microbial , Polymerase Chain Reaction , Sus scrofa/microbiologyABSTRACT
Chinese yam (Dioscorea opposita) is an important tuberous crop owing to its dual use as a food as well as a medicine. Tissue culture techniques allow the rapid multiplication of virus-free plant materials. The use of microtubers offers an attractive alternative to in vitro-grown plantlets for the micropropagation and exchange of healthy Chinese yam materials. A protocol for the in vitro production of Chinese yam microtubers was developed in this study. Though we tested both one-step and two-step procedures, only the two-step procedure showed favorable results for tuberization. Media with 60 g L(-1) sucrose yielded the highest microtuber index. We demonstrate that table sugar was an efficient and economical alternative to analytical grade sucrose for microtuber production. Using an orthogonal experimental design, we determined the optimal growth regulator combination for microtuber induction and development. The microtubers obtained from our protocol sprouted readily both in vitro and in soil.