Analysis of the dislocation activity of Mg-Zn-Y alloy using synchrotron radiation under tensile loading.

An understanding of deformation behavior and texture development is crucial for the formability improvement of Mg alloys. X-ray line profile analysis using the convolutional multiple whole profile (CMWP) fitting method allows the experimental determination of dislocation densities separately for different Burgers vectors up to a high deformation degree. A wider use of this technique still requires exploration and testing of various materials. In this regard, the reliability of the CMWP fitting method for Mg-Zn-Y alloys, in terms of the dislocation activity during tensile deformation, was verified in the present study by the combined analysis of electron backscatter diffraction (EBSD) investigation and visco-plastic self-consistent (VPSC) simulation. The predominant activity of non-basal 〈a〉 dislocation slip was revealed by CMWP analysis, and Schmid factor analysis from the EBSD results supported the higher potential of non-basal dislocation slip in comparison with basal 〈a〉 dislocation slip. Moreover, the relative slip activities obtained by the VPSC simulation also show a similar trend to those obtained from the CMWP evaluation.

On the heterogeneous microstructure and strengthening mechanisms in a laser welding AZ80 magnesium alloy.

This study investigates the microstructural characteristics and mechanical properties of a laser welded AZ80 magnesium alloy. The welding process led to the formation of coarse-grained fusion zone (FZ), where a secondary phase formed continuous network. Mg17Al12 precipitation and coarsening of grain boundaries occurred in the heat affected zone. The welded joint exhibited excellent mechanical properties with a yield strength of 202 MPa and a joint efficiency of 92%. The microstructure analysis via EPMA and EBSD in conjunction with synchrotron X-ray diffraction analysis reveals that precipitates and increased dislocation density in the fusion zone are primary strengthening mechanisms for the laser welded AZ80 Mg alloy.

Deformation Mechanisms of Magnesium Alloys with Rare-Earth and Zinc Additions under Plane Strain Compression.

The introduction of rare-earth (RE) elements into magnesium (Mg) alloys can significantly improve their ductility, thereby extending the applications of Mg products. However, the impacts of their chemical composition, temperature and processing methods on the mechanical properties of Mg products are highly debatable. In this work, we systematically investigate the deformation behaviors of Mg-Nd and Mg-Zn-Nd alloys using electron backscattered diffraction (EBSD) characterization. The samples were deformed to different stress levels to study the microstructure and texture development during channel die compression. The results reveal that the room temperature formability of the Mg-Nd alloy can be enhanced with the addition of Zn. This is attributed to the higher activities of prismatic slip and tensile twinning in the Mg-Zn-Nd alloy as compared to the binary counterpart, facilitating strain accommodation. When the strain increases, the growing and merging of the same twin variant rapidly consumes the parent grain, which is responsible for the texture modification from the transverse to the basal direction. At elevated temperatures, the twinning is suppressed in both alloys due to the decreased critical resolved shear stress of the non-basal slip systems. Additionally, an obvious sigmoidal yielding phenomenon is observed due to the multiple activation of the different deformation modes. These findings offer valuable insights into the evolution of the microstructure and texture during plane strain compression, elucidating the connections between material chemical composition, processing and mechanical properties, which are important for the advancement of Mg alloy application.

Twinning-Detwinning in Pre-Compressed and Thermally Treated ZX10 and ZN10 Alloys.

The deformation behavior of extruded Mg alloys with a Ca or Nd addition (up to 0.5 wt.%) is addressed with respect to a specified thermo-mechanical treatment, realized by pre-compression and subsequent heat treatment at intermediate temperature. The twinning-detwinning process is discussed with respect to the initial texture and applied heat treatment. Isothermal aging leads to precipitation and segregation along twin boundaries and dislocations in the pre-compressed Mg alloys, and, thus, variation in the mobility of twin boundaries (TB) is observed in the investigated alloys. Despite individual scenarios of TB mobility in particular grains, in general, the same TB mobility modes are observed in the alloys independently on Ca or Nd alloying. The microstructure development, particularly the twin volume fraction and the mobility of tensile {10-12} twin boundaries, is tracked using scanning electron microscopy, including backscattered electron (BSE) imaging and electron backscatter diffraction (EBSD) mapping.

Excellent age hardenability with the controllable microstructure of AXW100 magnesium sheet alloy.

Age-hardenability and corresponding improvement of the mechanical properties of Mg-1Al-0.7Ca and Mg-1Al-0.7Ca-0.7Y alloy sheets are addressed with respect to the microstructure and texture evolution during thermomechanical treatments. A fine grain structure and weak texture with the basal pole split into the sheet transverse direction are retained in the Mg-1Al-0.7Ca-0.7Y sheet even after the homogenization at 500 °C, due to the grain boundary pinning by Y-containing precipitates possessing a high thermal stability. Contrarily, the Mg-1Al-0.7Ca sheet shows a coarse microstructure and basal-type texture after the homogenization. The peak-aged condition is attained after the aging at 250 °C for 1800 s of both homogenized sheets, while the Y-containing sheet shows a higher hardness than the Mg-1Al-0.7Ca sheet. TEM analysis and thermodynamic calculation show the formation of metastable precipitates composed of Al, Ca, Y and Mg in the Mg-1Al-0.7Ca-0.7Y sheet at the homogenized and peak-aged conditions. A significant increase in the yield strength is obtained in the peak-aged condition from 162 MPa after the homogenization to 244 MPa, which arises from the increased size and number density of the precipitates. The high age-hardenability of the Mg-1Al-0.7Ca-0.7Y sheet attributes to the superior mechanical properties with an improved ductility promoted by the weak texture.

In vitro evaluation of the ZX11 magnesium alloy as potential bone plate: Degradability and mechanical integrity.

Considering the excellent biocompatibility of magnesium (Mg) alloys and their better mechanical properties compared to polymer materials, a wrought MgZnCa alloy with low contents of Zn (0.7 wt%) and Ca (0.6 wt%) (ZX11) was developed by twin roll casting (TRC) technology as potential biodegradable bone plates. The degradability and cell response of the ZX11 alloy were evaluated in vitro, as well as the mechanical integrity according to tensile tests after immersion. The results revealed a slightly higher degradation rate for the rolled ZX11, in comparison to that of the annealed one. It was mainly caused by the deformation twins and residual strain stored in the rolled alloy, which also seemed to promote localized degradation, thereby leading to a relatively fast deterioration in mechanical properties, especially the fracture strain/elongation. In contrast, after the annealing treatment, the alloy showed relatively lower strength, yet a lower degradation rate and quite stable elongation during the initial weeks of immersion were observed. More importantly, the ZX11 alloy, regardless of the annealing treatment, showed good in vitro cytocomopatibility regarding human primary osteoblasts. The assessment indicates the rolled alloy as a good choice for implantation sites where relatively high mechanical strength is needed during the early implantation, while the annealed alloy is a potential candidate for the sites which demand stable mechanical integrity during service. STATEMENT OF SIGNIFICANCE: The development of magnesium alloys as bone implants demands low degradation rate to gain not only a slow hydrogen evolution, but also a stable mechanical integrity during service. The present study develops a micro-alloyed MgZnCa alloy via twin roll casting (TRC) technology. It exhibited limited cytotoxicity, fairly low degradation rate and comparable strength to the reported Mg-1Zn-5Ca alloy which has been used as bone screws in clinical trials, indicating the great potential application as biodegradable bone implants. Furthermore, it showed good mechanical integrity during immersion to support the defect healing. Our results can aid other researchers to evaluate the mechanical integrity of biodegradable materials and to pay more attention to the effect of degradation behaviour on mechanical integrity of materials.

The small-angle and wide-angle X-ray scattering set-up at beamline BL9 of DELTA.

The multi-purpose experimental endstation of beamline BL9 at the Dortmund Electron Accelerator (DELTA) is dedicated to diffraction experiments in grazing-incidence geometry, reflectivity and powder diffraction measurements. Moreover, fluorescence analysis and inelastic X-ray scattering experiments can be performed. Recently, a new set-up for small-angle and wide-angle X-ray scattering utilizing detection by means of an image-plate scanner was installed and is described in detail here. First small-angle X-ray scattering experiments on aqueous solutions of lysozyme with different cosolvents and of staphylococcal nuclease are discussed. The application of the set-up for texture analysis is emphasized and a study of the crystallographic texture of natural bio-nanocomposites, using lobster and crab cuticles as model materials, is presented.