Evaluation of the Safe Water Optimization Tool to Provide Evidence-Based Chlorination Targets in Surface Waters: Lessons from a Refugee Setting in Uganda.

The Safe Water Optimization Tool (SWOT) generates evidence-based point-of-distribution free residual chlorine (FRC) targets to adjust chlorine dosing by operators and ensure water quality at point-of-consumption. To investigate SWOT effectiveness in surface waters, we conducted two before-and-after mixed-method evaluations in a Uganda refugee settlement served by piped and trucked surface water systems. We surveyed 888 users on water knowledge, attitudes, and practices; collected 2768 water samples to evaluate FRC,Escherichia coli, and disinfection by-products (DBPs) concentrations; and conducted nine key-informant interviews with system operators about SWOT implementation. After baseline data collection, SWOT chlorination targets were generated, increasing point-of-distribution FRC targets from 0.2 to 0.7-0.8 mg/L and from 0.3 to 0.9 mg/L for piped and trucked systems, respectively. At endline, household point-of-consumption FRC ≥ 0.2 mg/L increased from 23 to 35% and from 8 to 42% in the two systems. With these increases, we did not observe increased chlorinated water rejection or DBPs concentrations exceeding international guidelines. Informants reported that SWOT implementation increased knowledge and capacity and improved operations. Overall, SWOT-generated chlorination targets increased chlorine dosage, which improved household water quality in surface waters although less than previously documented with groundwater sources. Additional operator support on prechlorination water treatment processes is needed to ensure maximally effective SWOT implementation for surface water sources.

Impact of permanganate with polyaluminium chloride on algae-laden karst water: Behaviors and disinfection by-products control.

The removal of algal organic matter (AOM) through water treatment processes is a major approach of reducing the formation of disinfection by-products (DBP). Here, the formation of DBP from AOM in karst water under different combination of potassium permanganate (KMnO4) and polyaluminium chloride (PACl) was investigated. The effect of divalent ions (Ca2+ and Mg2+) on DBP formation was traced by AOM chemistry variations. For DBP formation after KMnO4 preoxidation, total carbonaceous DBPs (C-DBPs) decreased by 12.9% but nitrogen-containing DBPs (N-DBPs) increased by 18.8%. Conversely, the C-DBPs further increased by 3.3% but N-DBPs reduced by 10.7% after the addition of PACl besides KMnO4 preoxidation. The variations of aromatic protein-like, soluble microbial products-like compounds and ultraviolet absorbance at 254 nm (UV254) were highly correlated with the formation of DBPs, which suggest aromatic substances strongly affect DBP behaviors at different treatment conditions. In the presence of divalent ions (Ca2+ = 135.86 mg/L, Mg2+ = 18.51 mg/L), the combination of KMnO4 and PACl was more effective in controlling DBP formation compared to the situation without Ca2+ and Mg2+. Specifically, trichloromethane formation was largely inhibited compared to the other tested DBPs, which may refer to complexation of electron-donating groups via divalent ions. While Ca2+ and Mg2+ may not affect the nature of α-carbon and amine groups, so the variation of haloacetonitriles (HANs) was not obvious. The study enhances the understanding of the DBP formation patterns, transformation of carbon and nitrogen by preoxidation-coagulation (KMnO4-PACl) treatment in algae-laden karst water.

Chronic exposure to drinking water nitrate and trihalomethanes in the French CONSTANCES cohort.

Trihalomethanes (THMs) and nitrate are widespread chemicals in drinking water. Chronic exposure has been associated with increased cancer risk despite inconclusive evidence, partly due to the challenges in long-term exposure assessment and potential exposure misclassification. We estimated concentrations of nitrate and THMs in drinking water using a public regulatory monitoring database (SISE-Eaux) for CONSTANCES, a French population-based prospective cohort. We obtained 26,322,366 measurements of drinking water parameters from 2000 to 2020. We excluded missing, implausible and duplicated measurements; we corrected or imputed missing geocodes of sampling locations; we calculated the annual median concentration of nitrate and THMs by surveillance area. To predict missing annual median concentrations, linear mixed models with random intercept using surveillance area as a clustering variable were developed for each region for nitrate and the four THM components (chloroform, chlorodibromomethane, bromodichloromethane and bromoform) separately. Concentrations in the nearest surveillance area from the household were merged per year among 75,462 participants with residential history geocoded for 2000-2020. Estimated concentrations resulting from this approach were compared with measured concentrations in 100 samples collected in Paris, Rennes and Saint-Brieuc in 2021. Median annual concentrations of total THMs and nitrate at study participants' homes for 2000-2020 were, respectively, 15.7 µg/l (IQR: 15.2) and 15.2 mg/l (IQR: 20.8). Among these, 35% were based on measurements for nitrate (16% for THMs), 44% (46%) were predicted using on linear mixed models, and 21% (38%) were based on distribution unit median values. Conditional R2 predictive models ranged from 0.71 to 0.91 (median: 0.85) for nitrate, and from 0.48 to 0.80 for THMs (median: 0.68). These concentrations will allow future association analyses with risk of breast and colorectal cancer. Our cleaning process introduced here could be adapted to other large drinking water monitoring data.

Degradation products and transformation pathways of sulfamethoxazole chlorination disinfection by-products in constructed wetlands.

Antibiotics and available chlorine coexist in multiple aquatic environments, and thus antibiotics and their chlorinated disinfection by-products (Cl-DBPs) have been a great concern for the nature and human health. Herein, the degradation intermediates and transformation pathways of sulfamethoxazole (SMX) Cl-DBPs in constructed wetlands (CWs) were investigated. A total of five SMX Cl-DBPs and their twenty degradation products in CWs was identified in this study. SMX and its Cl-DBPs influenced the biodegradation rather than the adsorption process in CWs. S1 atom on sulfonyl group of SMX had the strongest nucleophilicity, and was most vulnerable for nucleophilic attack. N5 and N7 on amino groups, and C17 on the methyl group had great electronegativity, and were susceptible to electrophilic reactions. S1-N5 and S1-C8 bonds of SMX are the most prone to cleavage, followed by C11-N5, C16-C17, and C12-N7. The chlorination of SMX mainly occurred at S1, N5, and N7 sites, and went through S-C cleavage, S-N hydrolysis, and desulfonation. The biodegradation of SMX Cl-DBPs in CWs mainly occurred at S1, N5, N7, C8, and C17 sites, and went through processes including oxidation of methyl, hydroxyl and amino groups, desulfonation, decarboxylation, azo bond cleavage, benzene ring cleavage, ß-oxidation of fatty acids under the action of coenzymes. Over half of the SMX Cl-DBPs had greater bioaccumulation potential than their parent SMX, but the environmental risk of SMX Cl-DBPs was effectively reduced through the degradation by CWs.

Effect of exposure to disinfection by-products during swimming exercise on asthma-related immune responses.

Swimming is a widely practiced exercise in modern society, where there is a heightened interest in health. The exceptional benefits of swimming are well-known, yet the issue of water quality management inevitably arises due to its nature as an aquatic exercise. Several studies reported that chlorine disinfectants commonly used in swimming pool water disinfection could degrade into toxic disinfection by-products (DBPs) and suggested that the DBPs might induce respiratory disorders, including asthma. Conversely, there were also reports that the DBPs had no significant effects on respiratory conditions. In this study, we investigated the influence of swimming exercise and DBPs on asthma. The decomposition products had little effect on the number of T cells in various immune organs. However, swimming exercise was found to increase the cell count in proportion to the exercise duration. Nevertheless, there were no significant changes in other immune cells and the secretion of asthma-related cytokines. These findings indicate that the effects of swimming pool DBPs on respiratory conditions during swimming exercise are either negligible or absent, and instead, the immunological benefits gained through consistent swimming exercise outweigh any potential drawbacks.

Associations of exposure to disinfection by-products with blood coagulation parameters among women: Results from the Tongji reproductive and environmental (TREE) study.

BACKGROUND: Experimental studies have shown that disinfection byproducts (DBPs) induce coagulotoxicity, but human evidence is scarce. OBJECTIVE: This study aimed to explore the relationships of DBP exposures with blood coagulation parameters. METHODS: Among 858 women from the Tongji Reproductive and Environmental (TREE) study, urinary dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA) were detected as internal biomarkers of DBP exposures. We measured activated partial thromboplastin time (APTT), fibrinogen (Fbg), international normalized ratio (INR), prothrombin time (PT), and thrombin time (TT) as blood coagulation parameters. Multivariable linear regression models were utilized to estimate the relationships between urinary DCAA and TCAA and blood coagulation parameters. The effect modifications by demographic and lifestyle characteristics were further explored. RESULTS: Elevated tertiles of urinary DCAA concentrations were associated with increased PT and INR (11.29%, 95% CI: 1.66%, 20.92% and 0.99%, 95% CI: 0.08%, 1.90% for the third vs. first tertile, respectively; both P for trends < 0.05). Stratification analysis showed that the positive associations were only observed among younger (< 30 years), leaner (body mass index < 24.0 kg/m2), and non-passive smoking women. Moreover, elevated tertiles of urinary TCAA concentrations in positive associations with PT and INR were observed among younger women (17.89%, 95% CI: 2.50%, 33.29% and 1.82%, 95% CI: 0.34%, 3.30% for the third vs. first tertile, respectively; both P for trends < 0.05) but not among older women (both P for interactions < 0.05). CONCLUSION: Higher levels of urinary DCAA and TCAA are associated with prolonged clotting time among women.

Tailoring the topology of ZIF-67 metal-organic frameworks (MOFs) adsorbents to capture humic acids.

Chlorination is a versatile technique to combat water-borne pathogens. Over the last years, there has been continued research interest to abate the formation of chlorinated disinfection by-products (DBPs). To prevent hazardous DBPs in drinking water, it is decided to diminish organic precursors, among which humic acids (HA) resulting from the decomposition and transformation of biomass. Metal-organic frameworks (MOFs) such as zeolitic imidazolate frameworks (ZIFs) have recently received tremendous attention in water purification. Herein, customized ZIF-67 MOFs possessing various physicochemical properties were prepared by changing the cobalt source. The HA removal by ZIF-67-Cl, ZIF-67-OAc, ZIF-67-NO3, and ZIF-67-SO4 were 85.6%, 68.9%, 86.1%, and 87.4%, respectively, evidently affected by the specific surface area. HA uptake by ZIF-67-SO4 indicated a removal efficiency beyond 90% in 4  90% after 60 min mixing the solution with 0.3 g L-1 ZIF-67-SO4. Notably, an acceptable removal performance (∼72.3%) was obtained even at HA concentrations up to 100 mg L-1. The equilibrium data fitted well with the isotherm models in the order of Langmuir> Hill > BET> Khan > Redlich-Peterson> Jovanovic> Freundlich > and Temkin. The maximum adsorption capacity qm for HA uptake by ZIF-67-SO4 was 175.89 mg g-1, well above the majority of adsorbents. The pseudo-first-order model described the rate of HA adsorption by time. In conclusion, ZIF-67-SO4 presented promising adsorptive properties against HA. Further studies would be needed to minimize cobalt leaching from the ZIF-67-SO4 structure and improve its reusability safely, to ensure its effectiveness and the economy of adsorption system.

Exposure to disinfection by-products and risk of cancer: A systematic review and dose-response meta-analysis.

Disinfection by-products (DBPs), including trihalomethanes (THMs) and haloacetic acids (HAAs), have attracted attention due to their carcinogenic properties, leading to varying conclusions. This meta-analysis aimed to evaluate the dose-response relationship and the dose-dependent effect of DBPs on cancer risk. We performed a selective search in PubMed, Web of Science, and Embase databases for articles published up to September 15th, 2023. Our meta-analysis eventually included 25 articles, encompassing 8 cohort studies with 6038,525 participants and 10,668 cases, and 17 case-control studies with 10,847 cases and 20,702 controls. We observed a positive correlation between increased cancer risk and higher concentrations of total trihalomethanes (TTHM) in water, longer exposure durations, and higher cumulative TTHM intake. These associations showed a linear trend, with relative risks (RRs) and 95 % confidence intervals (CIs) being 1.02 (1.01-1.03), 1.04 (1.02-1.06), and 1.02 (1.00-1.03), respectively. Gender-specific analyses revealed slightly U-shaped relationships in both males and females, with males exhibiting higher risks. The threshold dose for TTHM in relation to cancer risk was determined to be 55 µg/L for females and 40 µg/L for males. A linear association was also identified between bladder cancer risk and TTHM exposure, with an RR and 95 % CI of 1.08 (1.05-1.11). Positive linear associations were observed between cancer risk and exposure to chloroform, bromodichloromethane (BDCM), and HAA5, with RRs and 95 % CIs of 1.02 (1.01-1.03), 1.33 (1.18-1.50), and 1.07 (1.03-1.12), respectively. Positive dose-dependent effects were noted for brominated THMs above 35 µg/L and chloroform above 75 µg/L. While heterogeneity was observed in the studies for quantitative synthesis, no publication bias was detected. Exposure to TTHM, chloroform, BDCM, or HAA5 may contribute to carcinogenesis, and the risk of cancer appears to be dose-dependent on DBP exposure levels. A cumulative effect is suggested by the positive correlation between TTHM exposure and cancer risk. Bladder cancer and endocrine-related cancers show dose-dependent and positive associations with TTHM exposure. Males may be more susceptible to TTHM compared to females.

Chemical-free vacuum ultraviolet irradiation as ultrafiltration membrane pretreatment technique: Performance, mechanisms and DBPs formation.

Membrane fouling induced by natural organic matter (NOM) has seriously affected the further extensive application of ultrafiltration (UF). Herein, a simple, green and robust vacuum ultraviolet (VUV) technology was adopted as pretreatment before UF and ultraviolet (UV) technology was used for comparison. The results showed that control effect of VUV pretreatment on membrane fouling was better than that of UV pretreatment, as evidenced by the increase of normalized flux from 0.27 to 0.38 and 0.73 after 30 min UV or VUV pretreatment, respectively. This is related to the fact that VUV pretreatment exhibited stronger NOM degradation ability than UV pretreatment owing to the formation of HO•. The steady-state concentration of HO• was calculated as 3.04 × 10-13 M and the cumulative exposure of HO• reached 5.52 × 10-10 M s after 30 min of VUV irradiation. And the second-order rate constant between NOM and HO• was determined as 1.36 × 104 L mg-1 s-1. Furthermore, fluorescence EEM could be applied to predict membrane fouling induced by humic-enriched water. Standard blocking and cake filtration were major fouling mechanisms. Moreover, extension of UV pretreatment time increased the disinfection by-products (DBPs) formation, the DBPs concentration was enhanced from 322.36 to 1187.80 µg/L after 210 min pretreatment. However, VUV pretreatment for 150 min reduced DBPs content to 282.57 µg/L, and DBPs content continued to decrease with the extension of pretreatment time, revealing that VUV pretreatment achieved effective control of DBPs. The variation trend of cytotoxicity and health risk of DBPs was similar to that of DBPs concentration. In summary, VUV pretreatment exhibited excellent effect on membrane fouling alleviation, NOM degradation and DBPs control under a certain pretreatment time.

Perspectives and understanding on the occurrence, toxicity and abatement technologies of disinfection by-products in drinking water.

Disinfection by-products (DBPs) are one of the significant emerging contaminants that have caught the attention of researchers worldwide due to their pervasiveness. Their presence in drinking water, even in shallow concentrations (in levels of parts per billion), poses considerable health risks. Therefore, it is crucial to understand their kinetics to understand better their formation and persistence in the water supply systems. This manuscript demonstrates different aspects of research carried out on DBPs in the past. A systematic approach was adopted for the bibliographical research that started with choosing appropriate keywords and identifying the most relevant manuscripts through the screening process. This follows a quantitative assessment of the extracted literature sample, which included the most productive and influential journal sources, the most widely used keywords, the most influential authors active in the research domain, the most cited articles, and the countries most actively engaged in the research field. Critical observations on the literature sample led to the qualitative assessment, wherein the past and current research trends were observed and reported. Finally, we identified the essential gaps in the available literature, which further led to recommending the course ahead in the research domain. This study will prove fruitful for young and established researchers who are or wish to work in this emerging field of research.

Estimating airborne trichloramine levels in indoor swimming pools using the well-mixed box model.

Exposure to airborne disinfection by-products, especially trichloramine (TCA), could cause various occupational health effects in indoor swimming pools. However, TCA concentration measurements involve specialized analysis conducted in specific laboratories, which can result in significant costs and time constraints. As an alternative, modeling techniques for estimating exposures are promising in addressing these challenges. This study aims to predict airborne TCA concentrations in indoor swimming pools using a mathematical model, the well-mixed box model, found in the IHMOD tool, freely available on the American Industrial Hygiene Association website. The model's predictions are compared with TCA concentrations measured during various bather load scenarios. The research involved conducting 2-hr successive workplace measurements over 16- to 18-hr periods in four indoor swimming pools in Quebec, Canada. TCA concentrations were estimated using the well-mixed box model, assuming a homogeneous mixing of air within the swimming pool environment. A novel approach was developed to estimate the TCA generation rate from swimming pool water, incorporating the number of swimmers in the model. Average measured concentrations of TCA were 0.24, 0.26, 0.14, and 0.34 mg/m3 for swimming pools 1, 2, 3, and 4, respectively. The ratio of these measured average concentrations to their corresponding predicted values ranged from 0.51 to 1.30, 0.67 to 1.04, 0.57 to 1.14, and 0.68 to 1.49 for the respective swimming pools. In a worst-case scenario simulating the swimming pool at full capacity (maximum bathers allowed), TCA concentrations were estimated as 0.23, 0.36, 0.14, and 0.37 mg/m3 for swimming pools 1, 2, 3, and 4. Recalculated concentrations by adjusting the number of swimmers so as not to exceed the recommended occupational limit concentration of 0.35 mg/m3 gives a maximum number of swimmers of 63 and 335 instead of currently 80 and 424 for swimming pools 2 and 4, respectively. Similarly, for swimming pools 1 and 3, the maximum number of swimmers could be 173 and 398 (instead of the current 160 and 225, respectively). These results demonstrated that the model could be used to estimate and anticipate airborne TCA levels in indoor swimming pools across various scenarios.

Trihalomethane prediction model for water supply system based on machine learning and Log-linear regression.

Laboratory determination of trihalomethanes (THMs) is a very time-consuming task. Therefore, establishing a THMs model using easily obtainable water quality parameters would be very helpful. This study explored the modeling methods of the random forest regression (RFR) model, support vector regression (SVR) model, and Log-linear regression model to predict the concentration of total-trihalomethanes (T-THMs), bromodichloromethane (BDCM), and dibromochloromethane (DBCM), using nine water quality parameters as input variables. The models were developed and tested using a dataset of 175 samples collected from a water treatment plant. The results showed that the RFR model, with the optimal parameter combination, outperformed the Log-linear regression model in predicting the concentration of T-THMs (N25 = 82-88%, rp = 0.70-0.80), while the SVR model performed slightly better than the RFR model in predicting the concentration of BDCM (N25 = 85-98%, rp = 0.70-0.97). The RFR model exhibited superior performance compared to the other two models in predicting the concentration of T-THMs and DBCM. The study concludes that the RFR model is superior overall to the SVR model and Log-linear regression models and could be used to monitor THMs concentration in water supply systems.

Adsorption kinetics, isotherms, and selectivity of trihalomethanes and haloacetonitriles by granular activated carbon.

The performance capability of granular activated carbon (GAC) adsorption in terms of disinfection by-product (DBPs) removal was investigated with synthetic water containing 1) trihalomethanes (THMs), 2) haloacetronitriles (HANs), and 3) Mix-THMs & HANs. The initial 20 min of adsorption resulted in the maximum adsorption rate, with the total THMs, total HANs, and total Mix-THMs & HANs being 4.972, 2.071, and 6.460 µg/gGAC-min, respectively. GAC dosage affects the adsorption selectivity of THMs and HANs. Under a low GAC dosage, the selectivity of GAC adsorbs more bromo-THMs than chloro-THMs. The adsorption selectivity of THMs on GAC following bromoform > dibromochloromethane > bromodichloromethane > chloroform was investigated. As the GAC concentration increased, the selectivity of THM adsorption by GAC became comparable. Chloro-HAN, in contrast to THMs, has a higher adsorption selectivity than bromo-HAN. Trichloroacetonitrile was removed by GAC more rapidly than the other HAN species when the GAC dose was increased. The toxin of bromoform was primarily eliminated through GAC adsorption, caused by a greater removal rate than that of the other THMs. As an implemented measure, GAC is introduced to reduce THMs and HANs and the toxic contents associated with THMs and HANs.

Impact of ozonation on disinfection byproducts formation from phenylalanine during chlorination.

As a strong oxidizing agent, ozone is used in some water treatment facilities for disinfection, taste and odor control, and removal of organic micropollutants. Phenylalanine (Phe) was used as the target amino acid to comprehensively investigate variability of disinfection byproducts (DBPs) formation during chlorine disinfection and residual chlorine conditions subsequent to ozonation. The results showed that subsequent to ozonation, the typical regulated and unregulated DBPs formation potential (DBPsFP), including trichloromethane (TCM), dichloroacetonitrile (DCAN), chloral hydrate (CH), dichloroacetic acid (DCAA), trichloroacetic acid (TCAA), and trichloroacetamide (TCAcAm) increased substantially, by 2.4, 3.3, 5.6, 1.2, 2.5, and 6.0 times, respectively, compared with only chlorination. Ozonation also significantly increased the DBPs yield under a 2 day simulated residual chlorine condition that mimicked the water distribution system. DBPs formations followed pseudo first order kinetics. The formation rates of DBPs in the first 6 hr were higher for TCM (0.214 hr-1), DCAN (0.244 hr-1), CH (0.105 hr-1), TCAcAm (0.234 hr-1), DCAA (0.375 hr-1) and TCAA (0.190 hr-1) than thereafter. The peak DBPsFP of TCM, DCAN, CH, TCAcAm, DCAA, and TCAA were obtained when that ozonation time was set at 5-15 min. Ozonation times > 30 min increased the mineralization of Phe and decreased the formation of DBPs upon chlorination. Increasing bromine ion (Br-) concentration increased production of bromine- DBPs and decreased chlorine-DBPs formation by 59.3%-92.2% . Higher ozone dosages and slight alkaline favored to reduce DBP formation and cytotoxicity. The ozonation conditions should be optimized for all application purposes including DBPs reduction.

[Hematological toxicity of disinfection by-product iodoacetic acid].

OBJECTIVE: To clarify the effect of iodoacetic acid(IAA) on the blood system and electrolyte balance, hence further study the intrinsic relation of blood routine parameters and electrolyte levels, major hematological toxicity effects and their pattern after IAA treatment. METHODS: Forty-eight 21-day-old male SPF grade Sprague-Dawley(SD) rats were gavaged with 0, 6.25, 12.5 and 25 mg/kg IAA for 31 days. After detections of blood routine and plasma inorganic ion levels, Spearman correlation coefficients were performed to evaluate their relationship. Changes in ferritin, transferrin, hepcidin, C-reactive protein and glyceraldehyde-3-phosphate dehydrogenase(GAPDH) were assessed by enzyme-linked immunosorbent assays. The EDock bioinformatics tool was applied to docking model of IAA and GAPDH. RESULTS: Compared to the control, high-dose IAA exposure had obvious inhibition effect on rat leukocytes with the total number declined by 51.12%, and neutrophils were particularly sensitive to IAA with the number reduced by 73.66%(P<0.01), and rat erythrocytes exhibited a small cell low pigment effect with hemoglobin and hematocrit decreased by 8.60% and 8.70%, respectively(P<0.05). But IAA had little effects on the platelet. Plasma iron, phosphorus, zinc and potassium levels were repressed significantly, while chlorine, sodium and magnesium levels were elevated obviously through IAA exposure. However, plasma calcium levels were hardly affected by IAA. In comparison with the control, iron levels declined by 67.09%, whereas magnesium levels increased by 131.82% in the high-dose group(P<0.01). Overall, correlation analyses uncovered that plasma iron metabolism was most strongly and positively correlated with levels of leukocyte, erythrocyte and platelet system parameters after IAA exposure, and the correlation coefficients of leukocyte number, mean hemoglobin content and mean erythrocyte volume were 0.637, 0.410 and 0.365, respectively(P<0.05). Compared to the control, in the high-dose IAA group, the plasma content of C-reactive protein was significantly upregulated by 13.30%(P<0.05), and plasma levels of transferrin and ferromodulin were also respectively elevated by 12.73% and 11.02%(P<0.05). But plasma levels of ferritin and GAPDH did not differ between groups. The docking model exhibited that IAA could bind to the 150 Cys active site of rat GAPDH did. CONCLUSION: IAA not only had toxic effects on rat leukocytes and the plasma electrolyte balance, but also generated inflammation and iron deficiency, leading to smaller erythrocytes and lower pigment.

Experimental and theoretical insight into carbamazepine degradation by chlorine-based advanced oxidation processes: Efficiency, energy consumption, mechanism and DBPs formation.

Chlorine has been widely used in different advanced oxidation processes (AOPs) for micropollutants removal. In this study, different chlorine-based AOPs, namely medium pressure (MP) UV/chlorine, low pressure (LP) UV/chlorine, and in-situ chlorination, were compared for carbamazepine (CBZ) removal efficiency, energy consumption, and disinfection by-products (DBPs) formation. All three processes could achieve nearly 100% CBZ removal, while the reaction time needed by in-situ chlorination was double the time required by UV/chlorine processes. The energy consumed per magnitude of CBZ removed (EE/O) of MP UV/chlorine was 13 times higher than that of LP UV/chlorine, and relative to that of in-situ chlorination process. Accordingly, MP and LP UV/chlorine processes generated one to two orders of magnitude more hydroxyl radicals (•OH) and reactive chlorine species (RCS) than in-situ chlorination. Besides, RCS were the dominant reactive species, contributing to 78.3%, 75.6%, and 71.6% of CBZ removal in MP, LP UV/chlorine, and in-situ chlorination, respectively. According to the Gibbs free energy barriers between CBZ and RCS/•OH calculated based on density functional theory (DFT), RCS had more reaction routes with CBZ and showed lower energy barrier in the main CBZ degradation pathways like epoxidation and formation of iminostilbene. When applied to secondary wastewater effluent, UV/chlorine and in-situ chlorination produced overall DBPs ranging from 104.77 to 135.41 µg/L. However, the production of chlorate during UV/chlorine processes was 15 times higher than that during in-situ chlorination.

Traditional methods and biosensors for detecting disinfection by-products in water: A review.

In recent years, pollution caused by disinfection by-products (DBPs) has become a global concern. Initially, there were fewer contaminants, and the mechanism of their generation was unclear; however, the number of contaminants has increased exponentially as a result of rapid industrialization and numerous economic activities (e.q., during the outbreak of COVID-19 a surge in the use of chlorinated disinfectants was observed). DBP toxicity results in various adverse health effects and organ failure in humans. In addition, it profoundly affects other forms of life, including animals, plants, and microorganisms. This review comprehensively discusses the pre-treatment methods of traditional and emerging DBPs and the technologies applied for their detection. Additionally, this paper provides a detailed discussion of the principles, applicability, and characteristics of traditional large-scale instrumentation methods (such as gas/liquid/ion chromatography coupled with mass spectrometry) for detecting DBPs based on their respective detection techniques. At the same time, the design, functionality, classification, and characteristics of rapid detection technologies (such as biosensors) are also detailed and analyzed.

Blood trihalomethane concentrations in relation to sperm mitochondrial DNA copy number and telomere length among 958 healthy men.

BACKGROUND: In animal and human studies, exposure to trihalomethanes (THMs) has been associated with reduced semen quality. However, the underlying mechanisms remain poorly understood. OBJECTIVE: To investigate the associations of blood THM concentrations with sperm mitochondrial DNA copy number (mtDNAcn) and telomere length (TL) among healthy men. METHODS: We recruited 958 men who volunteered as potential sperm donors. A single blood sample was collected from each participant at recruitment and measured for chloroform (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform (TBM) concentrations. Within a 90-day follow-up, the last semen sample provided by each participant was quantified for sperm mtDNAcn and TL. We used multivariable linear regression models to assess the associations between blood THM concentrations and sperm mtDNAcn and TL. We also performed stratified analyses according to the time intervals between baseline blood THM determinations and semen collection (i.e., 0-9, 10-14, 15-69, or >69 days) to explore potential windows of susceptibility. RESULTS: After adjusting for potential confounders, we found inverse associations between quartiles (or categories) of blood TBM, brominated THM (Br-THM, the sum of BDCM, DBCM, and TBM), and total THM (TTHM, the sum of all four THMs) concentrations and sperm mtDNAcn (all P for trend≤0.03). Besides, we found inverse associations between quartiles of blood TCM, Br-THM, chlorinated THM (Cl-THM, the sum of TCM, BDCM, and DBCM), and TTHM concentrations and sperm TL (all P for trend<0.10). Stratified analyses showed stronger associations between Br-THM concentrations and sperm mtDNAcn determined 15-69 days since baseline exposure determinations, and between blood TCM and TTHM concentrations and sperm TL determined >69 days since baseline exposure determinations. CONCLUSION: Exposure to THMs may be associated with sperm mitochondrial and telomeric dysfunction.

Sub-lethal toxicity of five disinfection by-products on microalgae determined by flow cytometry - Lines of evidence for adverse outcome pathways.

Standardised tests are often used to determine the ecotoxicity of chemicals and focus mainly on one or a few generic endpoints (e.g. mortality, growth), but information on the sub-cellular processes leading to these effects remain usually partial or missing. Flow cytometry (FCM) can be a practical tool to study the physiological responses of individual cells (such as microalgae) exposed to a stress via the use of fluorochromes and their morphology and natural autofluorescence. This work aimed to assess the effects of five chlorine-based disinfection by-products (DBPs) taken individually on growth and sub-cellular endpoints of the green microalgae Raphidocelis subcapitata. These five DBPs, characteristic of a chlorinated effluent, are the following monochloroacetic acid (MCAA), dichloroacetic acid (DCAA), trichloroacetic acid (TCAA), bromochloroacetic acid (BCAA) and 1,1-dichloropropan-2-one (1,1-DCP). Results showed that 1,1-DCP had the strongest effect on growth inhibition (EC50 = 1.8 mg.L-1), followed by MCAA, TCAA, BCAA and DCAA (EC50 of 10.1, 15.7, 27.3 and 64.5 mg.L-1 respectively). Neutral lipid content, reactive oxygen species (ROS) formation, red autofluorescence, green autofluorescence, size and intracellular complexity were significantly affected by the exposure to the five DBPs. Only mitochondrial membrane potential did not show any variation. Important cellular damages (>10%) were observed for only two of the chemicals (BCAA and 1,1-DCP) and were probably due to ROS formation. The most sensitive and informative sub-lethal parameter studied was metabolic activity (esterase activity), for which three types of response were observed. Combining all this information, an adverse outcome pathways framework was proposed to explain the effect of the targeted chemicals on R. subcapitata. Based on these results, both FCM sub-cellular analysis and conventional endpoint of algal toxicity were found to be complementary approaches.

Exploration of optimal disinfection model based on groundwater risk assessment in disinfection process.

Under the influence of different types of disinfectants and disinfection environments, the removal level of pathogens and the formation potential of disinfection by-products (DBPs) will have a dual impact on the groundwater environment. The key points for sustainable groundwater safety management are how to balance the positive and negative relationship and formulate a scientific disinfection model in combination with risk assessment. In this study, the effects of sodium hypochlorite (NaClO) and peracetic acid (PAA) concentrations on pathogenic E. coli and DBPs were investigated using static-batch and dynamic-column experiments, as well as the optimal disinfection model for groundwater risk assessment was explored using quantitative microbial risk assessment and disability-adjusted life years (DALYs) models. Compared to static disinfection, deposition and adsorption were the dominant factors causing E. coli migration at lower NaClO levels of 0-0.25 mg/L under dynamic state, while disinfection was its migration factor at higher NaClO levels of 0.5-6.5 mg/L. In contrast, E. coli removed by PAA was the result of the combined action of deposition, adsorption, and disinfection. The disinfection effects of NaClO and PAA on E. coli differed under dynamic and static conditions. At the same NaClO level, the health risk associated with E. coli in groundwater was higher, whereas, under the same PAA conditions, the health risk was lower. Under dynamic conditions, the optimal disinfectant dosage required for NaClO and PAA to reach the same acceptable risk level was 2 and 0.85 times (irrigation) or 0.92 times (drinking) of static disinfection, respectively. The results may help prevent the misuse of disinfectants and provide theoretical support for managing twin health risks posed by pathogens and DBPs in water treatment.