RESUMO
Two processes for crosslinking polyvinyl alcohol (PVA) with sulfosuccinic acid (SSA) and thermal crosslinking were used to fabricate a proton exchange membrane (PEM). Such PEMs are used in different fields involving fuel cell applications. The crosslinking reaction between PVA and SSA was confirmed using Fourier-transform infrared (FTIR) spectroscopy. The characterization of the prepared membranes, namely, ion exchange capacity (IEC), thermal analyses, water uptake, and ionic conductivity, was carried out. The IEC of the prepared membranes was found to be between 0.084 and 2.086 mmol g-1, resulting in an essential increase in the ionic conductivity. It was observed that the ionic conductivity was in the range of 0.003-0.023 S cm-1, depending on both temperature and SSA content. From the thermogravimetric analysis (TGA) results, it was revealed that the thermal stability of the crosslinked membranes improved. Moreover, water uptake decreased with increasing SSA content. Positron annihilation lifetime spectroscopy (PALS) was used to study the microstructure of the PVA/SSA membranes and their distribution at different ambient temperatures and relative humidity (RH) values. At room temperature, no significant change was observed in the free-volume holes up to 15 wt% SSA; thereafter, the size of the free-volume holes increased with the SSA content. The PALS results show that at different humidity values, the size of the free-volume holes for crosslinked PVA/SSA membranes is lower than those for Nafion membranes, i.e., the gas permeability for the prepared PVA/SSA membranes is less than that for the Nafion membrane. In addition, a strong correlation between the water uptake, ionic conductivity, tensile strength, and free-volume holes was observed.
RESUMO
A casting technique was used to prepare poly(vinyl alcohol) (PVA) blend polymers with different concentrations of Nylon-6,6 to increase the free-volume size and control the ionic conductivity of the blended polymers. The thermal activation energy for some blends is lower than that of pure polymers, indicating that their thermal stability is somewhere in between that of pure Nylon-6,6 and pure PVA. The degree of crystallinity of the blend sample (25.7%) was lower than that of the pure components (41.0 and 31.6% for pure Nylon-6,6 and PVA, respectively). The dielectric properties of the blended samples were investigated for different frequencies (50 Hz-5 MHz). The σac versus frequency was found to obey Jonscher's universal power law. The calculated values of the s parameter were increased from 0.53 to 0.783 for 0 and 100 wt.% Nylon-6,6, respectively, and values less than 1 indicate the hopping conduction mechanism. The barrier height (Wm) was found to increase from 0.33 to 0.72 for 0 and 100 wt.% Nylon-6,6, respectively. The ionic conductivity decreases as the concentration of Nylon-6,6 is blended into PVA because increasing the Nylon-6,6 concentration reduces the number of mobile charge carriers. Positron annihilation lifetime (PAL) spectroscopy was used to investigate the free volume's nanostructure. The hole volume size grows exponentially with the concentration of Nylon-6,6 mixed with PVA. The Nylon-6,6/PVA blends' free-volume distribution indicates that there is no phase separation in the blended samples. Mixing PVA and Nylon-6,6 resulted in a negative deviation (miscible blends), as evidenced by the interaction parameter's negative value. The strong correlation between the free-volume size and other macroscopic properties like ionic conductivity suggests that the free-volume size influences these macroscopic properties.
RESUMO
In this work, three nanoparticle samples, Ni4Co2Pt/CNFs, Ni5CoPt/CNFs and Ni6Pt/CNFs, were designed according to the molar ratio during loading on carbon nanofibers (CNFs) using electrospinning and carbonization at 900 °C for 7 h in an argon atmosphere. The metal loading and carbon ratio were fixed at 20 and 80 wt%, respectively. Various analysis tools were used to investigate the chemical composition, structural, morphological, and electrochemical (EC) properties. For samples with varying Co%, the carbonization process reduces the fiber diameter of the obtained electrospun nanofibers from 200-580 nm to 150-200 nm. The EDX mapping revealed that nickel, platinum, and cobalt were evenly and uniformly incorporated into the carbonized PVANFs. The prepared Ni-Co-Pt/CNFs have a face-centered cubic (FCC) structure with slightly increased crystallite size as the Co% decreased. The electrocatalytic properties of the samples were investigated for ethanol, methanol and urea electrooxidation. Using cyclic voltammetry (CV), chronoamperometry, and electrochemical impedance measurements, the catalytic performance and electrode stability were investigated as a function of electrolyte concentration, scan rate, and reaction time. When Co is added to Ni, the activation energy required for the electrooxidation reaction decreases and the electrode stability increases. In 1.5 M methanol, the Ni5CoPt/CNFs electrode showed the lowest onset potential and the highest current density (30.6 A/g). This current density is reduced to 28.2 and 21.2 A/g for 1.5 M ethanol and 0.33 M urea, respectively. The electrooxidation of ethanol, methanol, and urea using our electrocatalysts is a combination of kinetic/diffusion control limiting reactions. This research provided a unique approach to developing an efficient Ni-Co-Pt-based electrooxidation catalyst for ethanol, methanol and urea.
RESUMO
Polymer electrolyte membrane (PEM) fuel cells have the potential to reduce our energy consumption, pollutant emissions, and dependence on fossil fuels. To achieve a wide range of commercial PEMs, many efforts have been made to create novel polymer-based materials that can transport protons under anhydrous conditions. In this study, cross-linked poly(vinyl) alcohol (PVA)/poly(ethylene) glycol (PEG) membranes with varying alumina (Al2O3) content were synthesized using the solvent solution method. Wide-angle X-ray diffraction (XRD), water uptake, ion exchange capacity (IEC), and proton conductivity were then used to characterize the membranes. XRD results showed that the concentration of Al2O3 affected the degree of crystallinity of the membranes, with 0.7 wt.% Al2O3 providing the lowest crystallinity. Water uptake was discovered to be dependent not only on the Al2O3 group concentration (SSA content) but also on SSA, which influenced the hole volume size in the membranes. The ionic conductivity measurements provided that the samples were increased by SSA to a high value (0.13 S/m) at 0.7 wt.% Al2O3. Furthermore, the ionic conductivity of polymers devoid of SSA tended to increase as the Al2O3 concentration increased. The positron annihilation lifetimes revealed that as the Al2O3 concentration increased, the hole volume content of the polymer without SSA also increased. However, it was densified with SSA for the membrane. According to the findings of the study, PVA/PEG/SSA/0.7 wt.% Al2O3 might be employed as a PEM with high proton conductivity for fuel cell applications.