High-frequency and intrinsically stretchable polymer diodes.

Skin-like intrinsically stretchable soft electronic devices are essential to realize next-generation remote and preventative medicine for advanced personal healthcare1-4. The recent development of intrinsically stretchable conductors and semiconductors has enabled highly mechanically robust and skin-conformable electronic circuits or optoelectronic devices2,5-10. However, their operating frequencies have been limited to less than 100 hertz, which is much lower than that required for many applications. Here we report intrinsically stretchable diodes-based on stretchable organic and nanomaterials-capable of operating at a frequency as high as 13.56 megahertz. This operating frequency is high enough for the wireless operation of soft sensors and electrochromic display pixels using radiofrequency identification in which the base-carrier frequency is 6.78 megahertz or 13.56 megahertz. This was achieved through a combination of rational material design and device engineering. Specifically, we developed a stretchable anode, cathode, semiconductor and current collector that can satisfy the strict requirements for high-frequency operation. Finally, we show the operational feasibility of our diode by integrating it with a stretchable sensor, electrochromic display pixel and antenna to realize a stretchable wireless tag. This work is an important step towards enabling enhanced functionalities and capabilities for skin-like wearable electronics.

Functionalized NIR-II Semiconducting Polymer Nanoparticles for Single-cell to Whole-Organ Imaging of PSMA-Positive Prostate Cancer.

Development of molecular probes holds great promise for early diagnosis of aggressive prostate cancer. Here, 2-[3-(1,3-dicarboxypropyl) ureido] pentanedioic acid (DUPA)-conjugated ligand and bis-isoindigo-based polymer (BTII) are synthesized to formulate semiconducting polymer nanoparticles (BTII-DUPA SPN) as a prostate-specific membrane antigen (PSMA)-targeted probe for prostate cancer imaging in the NIR-II window. Insights into the interaction of the imaging probes with the biological targets from single cell to whole organ are obtained by transient absorption (TA) microscopy and photoacoustic (PA) tomography. At single-cell level, TA microscopy reveals the targeting efficiency, kinetics, and specificity of BTII-DUPA SPN to PSMA-positive prostate cancer. At organ level, PA tomographic imaging of BTII-DUPA SPN in the NIR-II window demonstrates superior imaging depth and contrast. By intravenous administration, BTII-DUPA SPN demonstrates selective accumulation and retention in the PSMA-positive tumor, allowing noninvasive PA detection of PSMA overexpressing prostate tumors in vivo. The distribution of nanoparticles inside the tumor tissue is further analyzed through TA microscopy. These results collectively demonstrate BTII-DUPA SPN as a promising probe for prostate cancer diagnosis by PA tomography.

Polyelectrolyte Composite Membranes Containing Electrospun Ion-Exchange Nanofibers: Effect of Nanofiber Surface Charges on Ionic Transport.

Poly(vinyl alcohol) (PVA)-based ion-exchange nanofibers (IEX-NFs) and their composite polyelectrolyte membranes were prepared and characterized. The PVA-based NFs are well dispersed and form a three-dimensional network structure in the polymer matrix, Nafion. All of the prepared membranes show a similar ion-exchange capacity of ∼1.0 mmol g-1. The ionic conductivities through the PVA- b-PSS-NF/Nafion composite membranes are superior to that of the Nafion membranes, but the conductivity through the PVA-NF/Nafion composite membrane is half that of the Nafion membrane. Our electrokinetic measurements clearly indicate that a high density of ion-exchange groups on the NF surface results in a continuous ionic transport path in the polymer matrix. In addition, the mechanical strength of all of the NF-composite membranes is improved compared with that of the membranes without NF.

Efficient Synthesis and Photosensitizer Performance of Nonplanar Organic Donor-Acceptor Molecules.

Nonplanar organic donor-acceptor molecules bearing a carboxylic acid group were synthesized by the formal [2+2] cycloaddition-retroelectrocyclization reaction between aniline-substituted alkynes and tetracyanoethylene (TCNE) or 7,7,8,8-tetracyanoquinodimethane (TCNQ). This reaction offers an atom-economic one-step approach to donor-acceptor chromophores in satisfactory high yields. The resulting donor-acceptor molecules were characterized by conventional analytical techniques. In addition, the nonplanarity and intermolecular interactions were investigated by X-ray crystallography. The energy levels and intramolecular charge-transfer (CT), evaluated by UV-Vis-near IR spectroscopy and electrochemistry, suggested that there is a linear correlation between the optical and electrochemical band gaps. Based on these structural and electronic analyses, the photosensitizer performances of the donor-acceptor molecules in dye-sensitized solar cells (DSSCs) were initially investigated using TiO2 or SnO2 electrodes. Although the power conversion efficiencies were limited, the incident-photon-to-current-conversion efficiency (IPCE) spectra indicated a better photocurrent generation for the devices on SnO2 as compared to those on TiO2.

All-Perfluorosulfonated-Ionomer Composite Membranes Containing Blow-Spun Fibers: Effect of a Thin Fiber Framework on Proton Conductivity and Mechanical Properties.

In this study, thin fiber composite polymer electrolyte membranes (PEMs) were prepared using short side-chain perfluorosulfonic acid (PFSA) ionomers, Aquivion, to create composite PEMs with improved proton conductivity and improved mechanical properties. PFSA thin fiber webs prepared by blow spinning and successive hot pressing were used as the porous substrate. Herein, PFSA ionomers were used for both the substrate and the matrix of the composite PEMs, and their structures, properties, and fuel cell performance were characterized. By adding the PFSA thin fiber webs to the matrix, the proton conductivity was enhanced and the mechanical properties were slightly improved. The prepared PFSA thin fiber composite PEM showed better FC performance than that of the pristine PFSA one for the high-temperature low-humidity condition in addition to the low-temperature high-humidity one. To the best of our knowledge, this is the first report on the all PFSA composite membranes containing a PFSA thin fiber framework.

A highly conducting organic metal derived from an organic-transistor material: benzothienobenzothiophene.

BTBT ([1]benzothieno[3,2-b][1]benzothiophene) is an organic semiconductor that realizes high mobility in organic transistors. Here we report that the charge-transfer (CT) salt, (BTBT)2PF6, shows a high room-temperature conductivity of 1500 S cm(-1). This compound exhibits a resistivity jump around 150 K, but when it is covered with Apiezon N grease the resistivity jump is suppressed, and the metallic conductivity is maintained down to 60 K. Owing to the very high conductivity, the ESR signal shows a significantly asymmetric Dysonian lineshape (A/B ≅ 3) even at room temperature. Since most organic conductors are based on strong electron donors, it is remarkable that such a weak electron donor as BTBT realizes a stable and highly conducting organic metal.

A novel polymeric chemosensor: dual colorimetric detection of metal ions through click synthesis.

A highly colored polystyrene derivative bearing side chain chromophores composed of dialkylanilino donor and cyano-based acceptor groups, prepared by atom-economic click postfunctionalization, displays the dual colorimetric detection behavior of several metal ions based on the specific interactions with different nitrogen atoms. Hard to borderline metal ions, such as Fe(3+) , Fe(2+) , and Sn(2+) , are always recognized by the dialkylanilino nitrogen atom, resulting in a decrease in the charge-transfer (CT) band intensity of the donor-acceptor chromophores. On the other hand, the recognition site of a soft metal ion of Ag(+) is the cyano nitrogen atom due to the readily formed multivalent coordination, which produces a bathochromic shift of the CT band.

Stabilization of organic field-effect transistors by tert-butyl groups in dibenzotetrathiafulvalene derivatives.

For a material for organic thin-film transistors, not only high mobility but also low threshold voltage and long-term stability are important requirements. In order to realize these properties, materials with relatively large oxidation potentials, namely weak donors, have been designed as p-channel organic semiconductors. Here we propose a different strategy; transistor properties of dibenzotetrathiafulvalene (DBTTF) are significantly improved by the introduction of tert-butyl groups. Although this chemical modification does not much change the ionization potential, small threshold voltage and stability over several months are attained together with the improved mobility, probably due to some kind of passivation effect of the bulky tert-butyl groups. In contrast, the systematic fluorine substitution rapidly diminishes the transistor performance. There are two kinds of herringbone structures with much different dihedral angles of about 50° and 130°, and the tert-butyl compound falls into the former category.

Preparation of Perfluorosulfonated Ionomer Nanofibers by Solution Blow Spinning.

In this work, we report the preparation of high-purity perfluorosulfonated ionomer (Nafion) nanofibers (NFs) via solution blow spinning (SBS). Fiber formation in solution jet spinning is strongly dependent on the structure of the spinning solution. Upon adding a small amount of poly(ethyleneoxide) (PEO) as a spinning aid to Nafion dispersion, most of the highly ordered Nafion aggregate disappeared, allowing the stable production of bead-free and smooth high-purity NFs (Nafion/PEO = 99/1) by SBS. The microstructure of the blowspun Nafion NFs differed from that of electrospun NFs. In the blowspun NFs, incomplete microphase separation between hydrophilic (ionic) and hydrophobic domains was observed, but the crystallization of CF2-CF2 chains was enhanced owing to the high extensional strain rate and rapid solidification during SBS. These findings provide fundamental information for the preparation and characterization of blowspun Nafion NFs.

Fluorination and chlorination effects on quinoxalineimides as an electron-deficient building block for n-channel organic semiconductors.

The quinoxalineimide (QI) unit, containing the electron-withdrawing quinoxaline and imide groups, is an electron-deficient building block for organic semiconductor materials. In this study, three fluorinated or chlorinated QIs (QI-1F, QI-2F, and QI-2Cl), have been designed and developed. We report the impact of the fluorination or chlorination of the QI unit on the electronic structures and charge carrier transport properties as compared to unsubstituted QI (QI-2H) bearing the same n-hexyl side chains. The frontier molecular orbital energy levels downshifted with the incorporation of fluorine or chlorine atoms onto the π-framework of QI. Single-crystal structure analyses revealed that all QI-based molecules have an entirely planar backbone and are packed into two-dimensional slipped stacks with diagonal electronic coupling that enables two-dimensional charge carrier transport. Notably, the doubly fluorinated or chlorinated QIs formed compact molecular packing in the single-crystal structures through an infinite intermolecular network relative to unsubstituted QI (QI-2H). The field-effect transistor-based QI molecules exhibited typical n-channel transport properties. As compared to unsubstituted QI (QI-2H), the chlorinated QI exhibited improved electron mobilities up to 7.1 × 10-3 cm2 V-1 s-1. The threshold voltages of the fluorinated or chlorinated QI devices were clearly smaller than that of QI-2H, which reflects the lowest unoccupied molecular orbital levels of the molecules. This study demonstrates that the fluorinated or chlorinated QIs are versatile building blocks in creating n-channel organic semiconductor materials.

Thiadiazole-fused Quinoxalineimide as an Electron-deficient Building Block for N-type Organic Semiconductors.

A strong electron-accepting planar π-conjugated framework, thiadiazole-fused quinoxalineimide (TQI), was designed and synthesized. Three TQI-based small molecules exhibit deep lowest-unoccupied molecular orbital (LUMO) levels, which require air stable n-channel conduction (∼-4.0 eV). Among these molecules, Hex-TQI-Br exhibits air-stable n-channel charge transport with a moderate mobility of 0.044 cm2 V-1 s-1.

Ionic Liquid-Based Electrolytes Containing Surface-Functionalized Inorganic Nanofibers for Quasisolid Lithium Batteries.

In the present study, surface amino-functionalized silica nanofibers (f-SiO2NFs, average diameter = 400 and 1000 nm) are used as one-dimensional (1-D) fillers of ionic liquid (IL)-based quasisolid electrolytes. On adding f-SiO2NFs to an IL (1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide, EMITFSA) containing lithium bis(trifluoromethanesulfonyl)-amide (LiTFSA), the well-dispersed 1-D nanofillers easily form a three-dimensional network structure in the IL, function as physical cross-linkers, and increase the viscosity of the composites, consequently providing a quasisolid state at a 3.5 wt % fraction of the NFs. Rheological measurements demonstrate that the prepared composites exhibit "gel-like" characteristics at 40-150 °C. All prepared composites show high ionic conductivities, on the order of 10-3 S cm-1, around room temperature. To investigate the additive effect of f-SiO2NFs in the composites, the lithium transference numbers are also evaluated. It is found that thinner NFs enhance the transference numbers of the composites. In addition, quasisolid lithium-ion cells containing the prepared composites demonstrate relatively high rate characteristics and good cycling performance at high temperature (125 °C).

Electrospun composite nanofiber yarns containing oriented graphene nanoribbons.

The graphene nanoribbon (GNR)/carbon composite nanofiber yarns were prepared by electrospinning from poly(acrylonitrile) (PAN) containing graphene oxide nanoribbons (GONRs), and successive twisting and carbonization. The electrospinning process can exert directional shear force coupling with the external electric field to the flow of the spinning solution. During electrospinning, the well-dispersed GONRs were highly oriented along the fiber axis in an electrified thin liquid jet. The addition of GONRs at a low weight fraction significantly improved the mechanical properties of the composite nanofiber yarns. In addition, the carbonization of the matrix polymer enhanced not only the mechanical but also the electrical properties of the composites. The electrical conductivity of the carbonized composite yarns containing 0.5 wt % GONR showed the maximum value of 165 S cm(-1). It is larger than the maximum value of the reported electrospun carbon composite yarns. Interestingly, it is higher than the conductivities of both the PAN-based pristine CNF yarns (77 S cm(-1)) and the monolayer GNRs (54 S cm(-1)). These results and Raman spectroscopy supported the hypothesis that the oriented GONRs contained in the PAN nanofibers effectively functioned as not only the 1-D nanofiller but also the nanoplatelet promoter of stabilization and template agent for the carbonization.

Ferromagnetic anomaly associated with the antiferromagnetic transitions in (donor)[Ni(mnt)2]-type charge-transfer salts.

Three newly prepared [Ni(mnt)2] complexes, (HMTTF)[Ni(mnt)2], (ChSTF)[Ni(mnt)2], and (DBTTF)2[Ni(mnt)2], are reported (DBTTF = dibenzotetrathiafulvalene, ChSTF = 2,3-cyclohexylenedithio-1,4-dithia-5,8-diselanafulvalene, HMTTF = bis(trimethylene)-tetrathiafulvalene, and mnt = maleonitrile dithiolate). The former two compounds have usual DA-type (D = donor, A = acceptor) mixed stacks, whereas the DBTTF complex has DDDDAA-type 6-fold columns. These compounds are electrical insulators, but the HMTTF and ChSTF complexes exhibit chiT minima at 16 and 55 K, respectively, followed by chiT peaks at 8 and 16 K. Below these temperatures the ESR signal disappears, indicating antiferromagnetic transitions. The origin of the ferromagnetic interaction is explained either from the difference of the g values between the donor and the anion or from the intrinsic ferromagnetic interaction of the [Ni(mnt)2] anions.