AlInAsSb Geiger-mode SWIR and eSWIR SPADs with high avalanche probability.

Single-photon avalanche diodes (SPADs) that are sensitive to photons in the Short-wave infrared and extended short-wave infrared (SWIR and eSWIR) spectra are important components for communication, ranging, and low-light level imaging. The high gain, low excess noise factor, and widely tunable bandgap of AlxIn1-xAsySb1-y avalanche photodiodes (APDs) make them a suitable candidate for these applications. In this work, we report single-photon-counting results for a separate absorption, charge, and multiplication (SACM) Geiger-mode SPAD within a gated-quenching circuit. The single-photon avalanche probabilities surpass 80% at 80 K, corresponding with single-photon detection efficiencies of 33% and 12% at 1.55 µm and 2 µm, respectively.

Considerations for excess noise measurements of low-k-factor Sb-based avalanche photodiodes.

In applications where high sensitivity is required, the internal gain mechanism of avalanche photodiodes can provide a performance advantage relative to p-i-n photodiodes. However, this internal gain mechanism leads to an excess noise that scales with gain. This excess noise term can be minimized by using materials systems in which impact ionization is initiated primarily by one carrier type. Recently, two Sb-based materials systems, AlInAsSb and AlGaAsSb, have exhibited exceptionally low excess noise, particularly for III-V compound materials. There are four important considerations that can impact the excess noise measurements in such low-noise materials. These considerations deal with the excess noise factor calculation method, measurement RF frequency, measurement wavelength, and the gain calculation method. In this paper, each of these factors is discussed, and their implications on excess noise are considered.

Narrow bandgap Al0.15In0.85As0.77Sb0.23 for mid-infrared photodetectors.

Mid-IR is a useful wavelength range for both science and military applications due to its low atmospheric attenuation and ability to be used for passive detection. However, many solutions for detecting light in this spectral region need to be operated at cryogenic temperatures as their required narrow bandgaps suffer from carrier recombination and band-to-band tunneling at room temperature leading to high dark currents. These problems can be alleviated by using a separate absorption, charge, and multiplication avalanche photodiode. We have recently demonstrated such a device with a 3-µm cutoff using Al0.15In0.85As0.77Sb0.23, as the absorber, grown on GaSb. Here we investigate Al0.15In0.85As0.77Sb0.23 as a simple PIN homojunction and provide metrics to aid in future designs using this material. PL spectrum measurements indicate a bandgap of 2.94 µm at 300 K. External quantum efficiencies of 39% and 33% are achieved at 1.55 µm and 2 µm respectively. Between 180 K and 280 K the activation energy is ∼0.22 eV, roughly half the bandgap of Al0.15In0.85As0.77Sb0.23, indicating thermal generation is dominant.

Frequency behavior of AlInAsSb nBn photodetectors and the development of an equivalent circuit model.

We report the frequency response of Al0.3InAsSb/Al0.7InAsSb nBn photodetectors. The 3-dB bandwidth of the devices varies from ∼ 150 MHz to ∼ 700 MHz with different device diameters and saturates with bias voltage immediately after the device turn on. A new equivalent circuit model is developed to explain the frequency behavior of nBn photodetectors. The simulated bandwidth based on the new equivalent circuit model agrees well with the bandwidth and the microwave scattering parameter measurements. The analysis reveals that the limiting factor of the bandwidth of the nBn photodetector is the large diffusion capacitance caused by the minority carrier lifetime and the device area. Additionally, the bandwidth of the nBn photodetector is barely affected by the photocurrent, which is found to be caused by the barrier structure in the nBn photodetector.

Room-temperature bandwidth of 2-µm AlInAsSb avalanche photodiodes.

We investigate the room-temperature bandwidth performance of AlInAsSb avalanche photodiodes under 2-µm illumination. Parameter characterization denotes RC-limited performance. While measurements indicate a maximum gain-bandwidth product of 44 GHz for a 60-µm-diameter device, we scale this performance to smaller device sizes based on the RC response. For a 15-µm-diameter device, we predict a maximum gain-bandwidth product of approximately 144 GHz based on the reported measurements.

Anisotropic thermoelectric effect and field-effect devices in epitaxial bismuthene on Si (111).

This experimental study reveals intriguing thermoelectric effects and devices in epitaxial bismuthene, two-dimensional (2D) bismuth with thickness ⩽30 nm, on Si (111). Bismuthene exhibits interesting anisotropic Seebeck coefficients varying 2-5 times along different crystal orientations, implying the existence of a puckered atomic structure like black phosphorus. An absolute value of Seebeck coefficient up to 237 µV K-1 sets a record for elemental Bi ever measured to the best of our knowledge. Electrical conductivity of bismuthene can reach up to 4.6 × 104 S m-1, which is sensitive to thickness and magnetic field. Along with a desired low thermal conductivity ∼1.97 W m-1 K that is 20% of its bulk form, the first experimental zT value at room temperature for bismuthene was measured ∼10-2, which is much higher than many other VA Xenes and comparable to its bulk compounds. Above results suggest a mixed buckled and puckered Bi atomic structure for epitaxial 2D bismuth on Si (111). Our work paves the way to explore potential applications, such as heat flux sensor, energy converting devices and so on for bismuthene.

Enhancing THz generation in photomixers using a metamaterial approach.

Photomixers at THz frequencies offer an attractive solution to fill the THz gap; however, conventional photomixer designs result in low output powers, on the order of microwatts, before thermal failure. We propose an alternative photomixer design capable of orders of magnitude enhancement of continuous-wave THz generation using a metamaterial approach. By forming a metal-semiconductor-metal (MSM) cavity through layering an ultrafast semiconductor material between subwavelength metal-dielectric gratings, tailored resonance can achieve ultrathin absorbing regions and efficient heat sinking. When mounted to a tunable E-patch antenna, gratings also act as vertically biased electrodes, further enhancing photoconductive gain by reducing the carrier path length to nanoscales. Thus, through these multiplicative enhancements, the metamaterial-enhanced photomixer is projected to generate THz powers in the milliwatt range and exceed the Manley-Rowe limit for frequencies less than 2 THz.

Photo-induced terahertz near-field dynamics of graphene/InAs heterostructures.

In this letter, we report optical pump terahertz (THz) near-field probe (n-OPTP) and optical pump THz near-field emission (n-OPTE) experiments of graphene/InAs heterostructures. Near-field imaging contrasts between graphene and InAs using these newly developed techniques as well as spectrally integrated THz nano-imaging (THz s-SNOM) are systematically studied. We demonstrate that in the near-field regime (λ/6000), a single layer of graphene is transparent to near-IR (800 nm) optical excitation and completely "screens" the photo-induced far-infrared (THz) dynamics in its substrate (InAs). Our work reveals unique frequency-selective ultrafast dynamics probed at the near field. It also provides strong evidence that n-OPTE nanoscopy yields contrast that distinguishes single-layer graphene from its substrate.

Giant electron-phonon coupling detected under surface plasmon resonance in Au film.

Surface plasmon resonance (SPR) is a powerful tool to amplify coherent phonon signals in metal films. In a 40 nm Au film excited with a 400 nm pump, we observed an abnormally large electron-phonon coupling constant of about 8×1017 W/(m3K), almost 40× larger than those reported in noble metals, and even comparable to transition metals. We attribute this phenomenon to quantum confinement and interband excitation. With SPR, we also observed two coherent phonon modes in a GaAs/AlAs quantum well thin film. Our finding provides a new approach to generate high-frequency acoustic phonons in noble metals and to study their nonlinear nature of propagation.

AlxIn1-xAsySb1-y photodiodes with low avalanche breakdown temperature dependence.

We report AlxIn1-xAsySb1-y PIN and Separate Absorption, Charge and Multiplication (SACM) avalanche photodiodes (APDs) with high temperature stability. This work is based on measurements of avalanche breakdown voltage of these devices for temperatures between 223 K and 363 K. Breakdown voltage temperature coefficients are shown to be lower than those of APDs fabricated with other materials with comparable multiplication layer thicknesses.

Black Phosphorus Flexible Thin Film Transistors at Gighertz Frequencies.

Black phosphorus (BP) has attracted rapidly growing attention for high speed and low power nanoelectronics owing to its compelling combination of tunable bandgap (0.3 to 2 eV) and high carrier mobility (up to ∼1000 cm(2)/V·s) at room temperature. In this work, we report the first radio frequency (RF) flexible top-gated (TG) BP thin-film transistors on highly bendable polyimide substrate for GHz nanoelectronic applications. Enhanced p-type charge transport with low-field mobility ∼233 cm(2)/V·s and current density of ∼100 µA/µm at VDS = -2 V were obtained from flexible BP transistor at a channel length L = 0.5 µm. Importantly, with optimized dielectric coating for air-stability during microfabrication, flexible BP RF transistors afforded intrinsic maximum oscillation frequency fMAX ∼ 14.5 GHz and unity current gain cutoff frequency fT ∼ 17.5 GHz at a channel length of 0.5 µm. Notably, the experimental fT achieved here is at least 45% higher than prior results on rigid substrate, which is attributed to the improved air-stability of fabricated BP devices. In addition, the high-frequency performance was investigated through mechanical bending test up to ∼1.5% tensile strain, which is ultimately limited by the inorganic dielectric film rather than the 2D material. Comparison of BP RF devices to other 2D semiconductors clearly indicates that BP offers the highest saturation velocity, an important metric for high-speed and RF flexible nanosystems.

Large-Area Dry Transfer of Single-Crystalline Epitaxial Bismuth Thin Films.

We report the first direct dry transfer of a single-crystalline thin film grown by molecular beam epitaxy. A double cantilever beam fracture technique was used to transfer epitaxial bismuth thin films grown on silicon (111) to silicon strips coated with epoxy. The transferred bismuth films retained electrical, optical, and structural properties comparable to the as-grown epitaxial films. Additionally, we isolated the bismuth thin films on freestanding flexible cured-epoxy post-transfer. The adhesion energy at the bismuth/silicon interface was measured to be ∼1 J/m2, comparable to that of exfoliated and wet transferred graphene. This low adhesion energy and ease of transfer is unexpected for an epitaxially grown film and may enable the study of bismuth's unique electronic and spintronic properties on arbitrary substrates. Moreover, this method suggests a route to integrate other group-V epitaxial films (i.e., phosphorus) with arbitrary substrates, as well as potentially to isolate bismuthene, the atomic thin-film limit of bismuth.

Impact of substrate characteristics on performance of large area plasmonic photoconductive emitters.

We present a comprehensive analysis of terahertz radiation from large area plasmonic photoconductive emitters in relation with characteristics of device substrate. Specifically, we investigate the radiation properties of large area plasmonic photoconductive emitters fabricated on GaAs substrates that exhibit short carrier lifetimes through low-temperature substrate growth and through epitaxially embedded rare-earth arsenide (ErAs and LuAs) nanoparticles in superlattice structures. Our analysis indicates that the utilized substrate composition and growth process for achieving short carrier lifetimes are crucial in determining substrate resistivity, carrier drift velocity, and carrier lifetime, which directly impact optical-to-terahertz conversion efficiency, radiation power, radiation bandwidth, and reliability of large area plasmonic photoconductive emitters.

Ultrafast dynamics of surface plasmons in InAs by time-resolved infrared nanospectroscopy.

We report on time-resolved mid-infrared (mid-IR) near-field spectroscopy of the narrow bandgap semiconductor InAs. The dominant effect we observed pertains to the dynamics of photoexcited carriers and associated surface plasmons. A novel combination of pump-probe techniques and near-field nanospectroscopy accesses high momentum plasmons and demonstrates efficient, subpicosecond photomodulation of the surface plasmon dispersion with subsequent tens of picoseconds decay under ambient conditions. The photoinduced change of the probe intensity due to plasmons in InAs is found to exceed that of other mid-IR or near-IR media by 1-2 orders of magnitude. Remarkably, the required control pulse fluence is as low as 60 µJ/cm(2), much smaller than fluences of ∼ 1-10 mJ/cm(2) previously utilized in ultrafast control of near-IR plasmonics. These low excitation densities are easily attained with a standard 1.56 µm fiber laser. Thus, InAs--a common semiconductor with favorable plasmonic properties such as a low effective mass--has the potential to become an important building block of optically controlled plasmonic devices operating at infrared frequencies.

Impact of fiber core diameter on dispersion and multiplexing in multimode-fiber links.

Large-core silica multimode fibers, whose core diameters are generally 50 µm or 62.5 µm, form the bulk of short and medium haul optical fiber links in existence today, owing to their low cost and ease of deployment. However, modal dispersion significantly limits the maximum data rates that they support. Recently, the ability to multiplex several streams of data through optical fibers has spawned the development of few-mode multimode fibers. These fibers possess the low-dispersion characteristics of single-mode fibers and the ability to multiplex several data streams using multiple-input multiple-output (MIMO) techniques and mode-specific filtering to increase data rates. While fibers with larger core diameters possess a larger number of spatial modes, they do not support data rates as high as few-mode fibers. In this paper, we describe a simulation based approach to characterize the tradeoffs between fiber diameter, achievable data rates and alignment tolerances of coherent links that employ graded-index multimode fibers (MMFs) of various dimensions, using the information theoretic outage capacity as the metric. The simulations used fibers' intermodal coupling characteristics to measure its multiplexing abilities and dispersion limitations with mode-specific filters and launch and detection spatial filter arrays. The simulations indicate that the bandwidth-length product achievable over few-mode fibers with MIMO techniques can exceed 250 Gb/s-km, while heavy mode spreading and limited mode selectivity limits the bandwidth-length product to under 25 Gb/s-km in fibers core diameters larger than 50 µm.

Tuning Multipolar Mie Scattering of Particles on a Dielectric-Covered Mirror.

Optically resonant particles are key building blocks of many nanophotonic devices such as optical antennas and metasurfaces. Because the functionalities of such devices are largely determined by the optical properties of individual resonators, extending the attainable responses from a given particle is highly desirable. Practically, this is usually achieved by introducing an asymmetric dielectric environment. However, commonly used simple substrates have limited influences on the optical properties of the particles atop. Here, we show that the multipolar scattering of silicon microspheres can be effectively modified by placing the particles on a dielectric-covered mirror, which tunes the coupling between the Mie resonances of microspheres and the standing waves and waveguide modes in the dielectric spacer. This tunability allows selective excitation, enhancement, suppression, and even elimination of the multipolar resonances and enables scattering at extended wavelengths, providing transformative opportunities in controlling light-matter interactions for various applications. We further demonstrate with experiments the detection of molecular fingerprints by single-particle mid-infrared spectroscopy and with simulations strong optical repulsive forces that could elevate the particles from a substrate.

Dynamic thermal emission control with InAs-based plasmonic metasurfaces.

Thermal emission from objects tends to be spectrally broadband, unpolarized, and temporally invariant. These common notions are now challenged with the emergence of new nanophotonic structures and concepts that afford on-demand, active manipulation of the thermal emission process. This opens a myriad of new applications in chemistry, health care, thermal management, imaging, sensing, and spectroscopy. Here, we theoretically propose and experimentally demonstrate a new approach to actively tailor thermal emission with a reflective, plasmonic metasurface in which the active material and reflector element are epitaxially grown, high-carrier-mobility InAs layers. Electrical gating induces changes in the charge carrier density of the active InAs layer that are translated into large changes in the optical absorption and thermal emission from metasurface. We demonstrate polarization-dependent and electrically controlled emissivity changes of 3.6%P (6.5% in relative scale) in the mid-infrared spectral range.

Versatile Large-Area Custom-Feature van der Waals Epitaxy of Topological Insulators.

As the focus of applied research in topological insulators (TI) evolves, the need to synthesize large-area TI films for practical device applications takes center stage. However, constructing scalable and adaptable processes for high-quality TI compounds remains a challenge. To this end, a versatile van der Waals epitaxy (vdWE) process for custom-feature bismuth telluro-sulfide TI growth and fabrication is presented, achieved through selective-area fluorination and modification of surface free-energy on mica. The TI features grow epitaxially in large single-crystal trigonal domains, exhibiting armchair or zigzag crystalline edges highly oriented with the underlying mica lattice and only two preferred domain orientations mirrored at 180°. As-grown feature thickness dependence on lateral dimensions and denuded zones at boundaries are observed, as explained by a semiempirical two-species surface migration model with robust estimates of growth parameters and elucidating the role of selective-area surface modification. Topological surface states contribute up to 60% of device conductance at room temperature, indicating excellent electronic quality. High-yield microfabrication and the adaptable vdWE growth mechanism with readily alterable precursor and substrate combinations lend the process versatility to realize crystalline TI synthesis in arbitrary shapes and arrays suitable for facile integration with processes ranging from rapid prototyping to scalable manufacturing.

Highly tensile-strained Ge/InAlAs nanocomposites.

Self-assembled nanocomposites have been extensively investigated due to the novel properties that can emerge when multiple material phases are combined. Growth of epitaxial nanocomposites using lattice-mismatched constituents also enables strain-engineering, which can be used to further enhance material properties. Here, we report self-assembled growth of highly tensile-strained Ge/In0.52Al0.48As (InAlAs) nanocomposites by using spontaneous phase separation. Transmission electron microscopy shows a high density of single-crystalline germanium nanostructures coherently embedded in InAlAs without extended defects, and Raman spectroscopy reveals a 3.8% biaxial tensile strain in the germanium nanostructures. We also show that the strain in the germanium nanostructures can be tuned to 5.3% by altering the lattice constant of the matrix material, illustrating the versatility of epitaxial nanocomposites for strain engineering. Photoluminescence and electroluminescence results are then discussed to illustrate the potential for realizing devices based on this nanocomposite material.

Nonlinear terahertz devices utilizing semiconducting plasmonic metamaterials.

The development of responsive metamaterials has enabled the realization of compact tunable photonic devices capable of manipulating the amplitude, polarization, wave vector and frequency of light. Integration of semiconductors into the active regions of metallic resonators is a proven approach for creating nonlinear metamaterials through optoelectronic control of the semiconductor carrier density. Metal-free subwavelength resonant semiconductor structures offer an alternative approach to create dynamic metamaterials. We present InAs plasmonic disk arrays as a viable resonant metamaterial at terahertz frequencies. Importantly, InAs plasmonic disks exhibit a strong nonlinear response arising from electric field-induced intervalley scattering, resulting in a reduced carrier mobility thereby damping the plasmonic response. We demonstrate nonlinear perfect absorbers configured as either optical limiters or saturable absorbers, including flexible nonlinear absorbers achieved by transferring the disks to polyimide films. Nonlinear plasmonic metamaterials show potential for use in ultrafast terahertz (THz) optics and for passive protection of sensitive electromagnetic devices.