RESUMO
Oxides formed by electrochemical treatment of metals frequently have properties and structures very different from the respective bulk oxides. Here, electronic structure and chemical composition were investigated for the oxide formed on polycrystalline zinc after electrochemical oxidation, and after subsequent reduction, in a Na2CO3 electrolyte. Photoluminescence and spectroscopic ellipsometry show the presence of states deep in the ZnO band gap in the oxidized sample, which consists of a highly disordered oxide. These states determine the absorption of light in the visible spectral range. After reduction, the characteristics of the ZnO electronic structure have disappeared, leaving a defect-dominated material with a band gap of ~1.8 eV. Complementary detailed analysis of the morphology of the resulting surfaces shows hexagon-shaped metallic Zn-"nanoplates" to be formed in the reduction step. The optical appearance of the surfaces is dark, because of their efficient extinction of light over a large part of the visible spectrum. The optical appearance is a result of changed surface morphology and electronic structure of the oxide film. Such materials may possess interesting applications in photocatalysis or photoelectrochemistry.
RESUMO
Dealloying is widely utilized but is a dangerous corrosion process as well. Here we report an atomistic picture of the initial stages of electrochemical dealloying of the model system Cu(3)Au (111). We illuminate the structural and chemical changes during the early stages of dissolution up to the critical potential, using a unique combination of advanced surface-analytical tools. Scanning tunneling microscopy images indicate an interlayer exchange of topmost surface atoms during initial dealloying, while scanning Auger-electron microscopy data clearly reveal that the surface is fully covered by a continuous Au-rich layer at an early stage. Initiating below this first layer a transformation from stacking-reversed toward substrate-oriented Au surface structures is observed close to the critical potential. We further use the observed structural transitions as a reference process to evaluate the mechanistic changes induced by a thiol-based model-inhibition layer applied to suppress surface diffusion. The initial ultrathin Au layer is stabilized with the intermediate island morphology completely suppressed, along an anodic shift of the breakdown potential. Thiol-modification induces a peculiar surface microstructure in the form of microcracks exhibiting a nanoporous core. On the basis of the presented atomic-scale observations, an interlayer exchange mechanism next to pure surface diffusion becomes obvious which may be controlling the layer thickness and its later change in orientation.
RESUMO
A combined approach of pH-dependent in-situ AFM topography and ex-situ LEED studies of the stability and dissolution of single-crystalline ZnO(0001)-Zn surfaces in aqueous media is presented. Hydroxide-stabilized and single-crystalline ZnO(0001)-Zn surfaces turned out to be stable within a wide pH range between 11 and 4 around the point of zero charge of pH PZC = 8.7 +/- 0.2. Hydroxide stabilization turned out to be a very effective stabilization mechanism for polar oxide surfaces in electrolyte solutions. The dissolution of the oxide surface started at an acidic pH level of 5.5 and occurred selectively at the pre-existing step edges, which consist of nonpolar surfaces. In comparison, the oxide dissolution along the ZnO(0001) direction proved to be effectively inhibited above a pH value of 3.8. On the basis of these microscopic observations, the mechanistic understanding of the acidic dissolution process of ZnO could be supported. Moreover, both the in-situ AFM and the ex-situ LEED studies showed that the stabilization mechanism of the ZnO(0001) surfaces changes in acidic electrolytes. At pH values below 3.8, the hydroxide-stabilized surface is destabilized by dissolution of the well-ordered radical3. radical3. R30 hydroxide ad-layer as proven by LEED. Restabilization occurs and leads to the formation of triangular nanoterraces with a specific edge termination. However, below pH 4 the surface structure of the crystal itself is ill-defined on the macroscopic scale because preferable etching along crystal defects as dislocations into the bulk oxide results in very deep hexagonal etching pits.
RESUMO
Two different approaches under ambient conditions were developed for the preparation of clean, non-reconstructed, single crystalline ZnO(0001)-Zn surfaces. The surface preparation by a wet chemical etching procedure was compared with the same treatment in combination with a subsequent heat treatment in humidified oxygen atmosphere. Depending on the preparation technique, atomically flat terraces with a width of 100 nm to several micrometers were observed using an atomic force microscope (AFM). The obtained surface structures were further characterized by means of angle resolved X-ray photoelectron spectroscopy (AR-XPS), time-of-flight secondary ion mass spectroscopy (ToF-SIMS), Auger electron spectroscopy (AES) and low energy electron diffraction (LEED) measurements. Based on these results it is shown that the obtained surfaces are, in contrast to surfaces prepared under UHV conditions, stabilised by the adsorption of a monolayer of hydroxides. The important role of H(2)O during the heat treatment is pointed out by comparing the results of the same heat treatment in the absence of water. H(2)O turned out to play an important role in the reorganization process of the surface at elevated temperatures, thereby yielding extremely large atomically flat terraces. The terminating edges of these terraces were found to include 120 degrees and 60 degrees angles, thus perfectly reflecting the hexagonal surface structure.