Characterization of spent nuclear fuel canister surface roughness using surface replicating molds.

In this study we present a replication method to determine surface roughness and to identify surface features when a sample cannot be directly analyzed by conventional techniques. As a demonstration, this method was applied to an unused spent nuclear fuel dry storage canister to determine variation across different surface features. In this study, an initial material down-selection was performed to determine the best molding agent and determined that non-modified Polytek PlatSil23-75 provided the most accurate representation of the surface while providing good usability. Other materials that were considered include Polygel Brush-On 35 polyurethane rubber (with and without Pol-ease 2300 release agent), Polytek PlatSil73-25 silicone rubber (with and without PlatThix thickening agent and Pol-ease 2300 release agent), and Express STD vinylpolysiloxane impression putty. The ability of PlatSil73-25 to create an accurate surface replica was evaluated by creating surface molds of several locations on surface roughness standards representing ISO grade surfaces N3, N5, N7, and N8. Overall, the molds were able to accurately reproduce the expected roughness average (Ra) values, but systematically over-estimated the peak-valley maximum roughness (Rz) values. Using a 3D printed sample cell, several locations across the stainless steel spent nuclear fuel canister were sampled to determine the surface roughness. These measurements provided information regarding variability in normal surface roughness across the canister as well as a detailed evaluation on specific surface features (e.g., welds, grind marks, etc.). The results of these measurements can support development of dry storage canister ageing management programs, as surface roughness is an important factor for surface dust deposition and accumulation. This method can be applied more broadly to different surfaces beyond stainless steel to provide rapid, accurate surface replications for analytical evaluation by profilometry.

Considerations for realistic atmospheric environments: An application to corrosion testing.

Measured salt compositions in dust collected over roughly the last decade from surfaces of in-service stainless-steel alloys at four locations around the United States are presented, along with the predicted brine compositions that would result from deliquescence of these salts. The salt compositions vary greatly from ASTM seawater and from laboratory salts (i.e., NaCl or MgCl2) commonly used on corrosion testing. The salts contained relatively high amounts of sulfates and nitrates, evolved to basic pH values, and exhibited deliquescence relative humidity values (RH) higher than seawater. Additionally, inert dust in components were quantified and considerations for laboratory testing are presented. The observed dust compositions are discussed in terms of the potential corrosion behavior and are compared to commonly used accelerated testing protocols. Finally, ambient weather conditions and their influence on diurnal fluctuations in temperature (T) and RH on heated metal surfaces are evaluated and a relevant diurnal cycle for laboratory testing a heated surface has been developed. Suggestions for future accelerated tests are proposed that include exploration of the effects of inert dust particles on atmospheric corrosion, chemistry considerations, and realistic diurnal fluctuations in T and RH. Understanding mechanisms in both realistic and accelerated environments will allow development of a corrosion factor (i.e., scaling factor) for the extrapolation of laboratory-scale test results to real world applications.

Physical and chemical properties of sea salt deliquescent brines as a function of temperature and relative humidity.

Thermodynamic modeling has been used to predict chemical compositions of brines formed by the deliquescence of sea salt aerosols. Representative brines have been mixed, and physical and chemical properties have been measured over a range of temperatures. Brine properties are discussed in terms of atmospheric corrosion of austenitic stainless steel, using spent nuclear fuel dry storage canisters as an example. After initial loading with spent fuel, during dry storage, the canisters cool over time, leading to increased surface relative humidities and evolving brine chemistries and properties. These parameters affect corrosion kinetics and damage distributions, and may offer important constraints on the expected timing, rate, and long-term impacts of canister corrosion.

Use of capillary electrophoresis for monitoring citrus juice composition.

New trends in adulteration monitoring, favor the development of methods analyzing simultaneously as many compounds as possible. Capillary electrophoresis has been applied to the examination of a broad spectrum of citrus juice molecules that absorb in the UV and in the visible light. Depending on the conditions up to thirty compounds could be separated. The identified molecules included phenolic amines, amino acids, flavonoids, polyphenols and vitamin C. Samples can be analyzed without specific preparation and the best separations were obtained with diluted solutions due to a stacking effect. This method has been applied to the comparison of pure orange juice and pulpwash, a major adulterant of orange juice. Several significant quantitative differences were seen and it is hoped that this procedure will provide a more precise way of estimating pulpwash in orange juice.

Extraction parameters and capillary electrophoresis analysis of limonin glucoside and phlorin in citrus byproducts.

Limonin glucoside (LG) and phlorin were extracted from citrus fruit tissues and assayed by capillary electrophoresis (CE). LG was determined in dried [1.20 +/- 0.10 mg of dry weight (dw)] and wet peel residues (1.16 +/- 0.04 mg of dw), orange juice finisher pulp (0.58 +/- 0.03 mg of dw), dried grapefruit seeds (2.70 +/- 0.15 mg of dw), and 50 degrees Brix molasses (2225 +/- 68 mg/L). Phlorin was purified from orange peel residue and grapefruit albedo, and concentrations were determined in some citrus products. Phlorin and LG were extracted from residues with water/pectinase or with water solutions of methanol and ethanol. Efficient LG extraction from grapefruit seeds (2.40 +/- 0.15 mg/g) was achieved with 50-65% methanol, solvent polarity P' approximately equal to 7-8. Extracts were purified and concentrated by adsorptive resins and HPLC to obtain 95% pure compounds of LG and phlorin. CE analysis did not require extract purification beyond filtration. LG and phlorin migrated as anions in electropherograms containing peaks representing other citrus flavonoids and limonoid glucosides.

Capillary electrophoresis analysis of orange juice pectinesterases.

Pectinesterase (PE) was extracted from orange juice and pulp with 1 M NaCl, desalted, and separated using capillary electrophoresis (CE) gel procedures (CE-SDS-CGE) and isoelectric focusing (CE-IEF). PE resolved as a single peak using noncoated fused silica columns with CE-SDS-CGE. CE-IEF separation of PE required acryloylaminoethoxyethanol-coated columns, which had limited stability. Thermal stability of PE extracts before and after heating at 75 degrees C for 30 min and at 95 degrees C for 5 min established heat labile and heat stabile fractions with identical PE migration times by CE-SDS-CGE or CE-IEF. Peak magnitude decreased to a constant value as heating time increased at 75 degrees C. Regression analysis of CE-SDS-CGE peak migration times of molecular weight (MW) standards estimated both heat labile and heat stable PE at MW approximately 36 900. Traditional SDS-PAGE gel separation of MW standards and active PE isolated by IEF allowed estimation of MW approximately 36 000. CE-SDS-CGE allowed presumptive, but not quantitative, detection of active PE in fresh juice.

Sonographic examination of the adult brain.

Phased-array real-time transcranial ultrasound with a 2.5-MHz transducer was used to examine 23 normal adult volunteers and patients, and 8 selected patients with abnormalities proven by computed tomography. Normal cerebral landmarks were consistently seen and pulsed Doppler signals were often obtainable from central cerebral arteries. Dilated lateral ventricles, subdural hygromas, or cerebral masses were identified in 6 of the 8 patients. In the 2 others abnormal cases, known suprasellar aneurysms were missed. While current technology will not provide accurate screening for cerebral abnormalities, ultrasound imaging may often be adequate for follow-up examinations and for midline evaluation, and may provide simplified preoperative localization of some brain lesions. Doppler ultrasound examinations may be used for intracranial vessel hemodynamic evaluation.