MicroRNA-30c as a novel diagnostic biomarker for primary and secondary B-cell lymphoma of the CNS.

Primary lymphomas of the central nervous system (PCNSL) are highly aggressive tumors affecting exclusively the CNS, meninges, and eyes. PCNSL must be separated from secondary spread of systemic lymphoma to the CNS (SCNSL), which may occur at diagnosis or relapse of systemic lymphomas. At present, there are no valid methods to distinguish PCNSL from SCNSL based on tumor biopsy because of similar histological presentation. However, SCNSL and PCNSL are different in terms of prognosis and adequate therapy protocols. MicroRNA expression profiles of CSF samples collected from SCNSL and PCNSL patients were compared using microRNA arrays. MiR-30c revealed the largest differential expression and was selected for validation by RT-PCR on 61 CSF samples from patients with PCNSL and 14 samples from SCNSL. MiR-30c was significantly increased in patients with SCNSL compared to PCNSL (p < 0.001). MiR-30c levels in CSF enabled the differentiation of patients with PCNSL from SCNSL with an area under the curve (AUC) of 0.86, with a sensitivity of 90.9% and a specificity of 85.5%. Our data suggest that miR-30c detected in the CSF can serve as biomarker for distinction between PCNSL and SCNSL. The validation in a larger cohort is needed. With respect to its function, miR-30c may facilitate lymphoma cells to engraft into CNS by interaction with CELSR3 gene that controls the function of ependymal cilia and, thus, affects the circulation of CSF.

Durability and Corrosion Resistance Test of Adhesive Joints Using Two Adherence Promoters for the Connection of Aerospace Aluminum Alloys.

This article presents the technology of making an adhesive joint using two primers: Corrosion Inhibiting Primer BR127 (previously used, containing chromium compounds) and, as a potential substitute, Structural Adhesives Primer EW 5000 AS (which does not contain any compounds harmful to the environment). An adhesive film and a sol-gel primer were used to make the joint of two aluminum sheets, and various technologies were used for applying adhesion promoters. The mechanical properties of the prepared samples were tested using two test methods: wedge tests and shear strength tests. In both cases, the samples were aged in laboratory conditions in tap water, and in a climatic chamber (with increased temperature and humidity). The obtained results indicate that the best technology for preparing the joint using each primer is the technology that assumes heating the primer and hardening the adhesive film in one operation. The results of the strength tests indicate that the samples made using the EW 5000 AS primer have higher strength properties under all tested seasoning conditions compared to samples made using the BR 127 primer. It was also confirmed that the presence of moisture and/or water reduces the mechanical strength of the adhesive joints independently of the primer used. The results of the polymer coatings tests to protect the aluminum substrate against corrosion showed that the coatings are only effective for a certain period of time, and, as a result of the NSS test, after 480 h, all the samples were subject to corrosion.

Prediction of Strength Properties of Filling Packets in Selected Cooling Towers.

The operating conditions of thermoplastic polymer materials determine the changes in their functional properties. Accelerated aging tests do not give a full picture of the changes taking place in the polymer material, hence the conclusions drawn on the basis of exposure of these materials to damaging effects in real operating conditions are particularly important. The aim of the study was to determine the degree of degradation of polypropylene films used in the drainage blocks of cooling towers in a selected power plant in the Silesian voivodship, which allowed forecasting the operating time over a period of 10 years. A number of 600 mm high drip blocks were tested, on which 300 mm high blocks were mounted. The tests were carried out on films subjected to the aging process in the conditions of continuous operation of a cooling tower (almost 100% humidity). The water flow is accompanied by heat exchange, the side effect of which is deposits formation on the surface of the drip blocks, negatively affecting the operation of the cooling tower. The degree of degradation resulting from operational aging was assessed on the basis of the strength properties determined in the static tensile test, thermogravimetric analysis and FTIR spectra. Changes in properties during operation were determined on the basis of the obtained results of the strength tests, which were compared with the tensile strength and elongation at break of reference samples (not subjected to aging in the operating conditions of cooling tower drip blocks). The obtained results were related to the properties of the reference samples not subjected to the degradation process. Based on the collected data, the tensile strength and deformation at fracture after a 10-year service life were predicted.