RESUMO
Displays in which arrays of microscopic 'particles', or chiplets, of inorganic light-emitting diodes (LEDs) constitute the pixels, termed MicroLED displays, have received considerable attention1,2 because they can potentially outperform commercially available displays based on organic LEDs3,4 in terms of power consumption, colour saturation, brightness and stability and without image burn-in issues1,2,5-7. To manufacture these displays, LED chiplets must be epitaxially grown on separate wafers for maximum device performance and then transferred onto the display substrate. Given that the number of LEDs needed for transfer is tremendous-for example, more than 24 million chiplets smaller than 100 µm are required for a 50-inch, ultra-high-definition display-a technique capable of assembling tens of millions of individual LEDs at low cost and high throughput is needed to commercialize MicroLED displays. Here we demonstrate a MicroLED lighting panel consisting of more than 19,000 disk-shaped GaN chiplets, 45 µm in diameter and 5 µm in thickness, assembled in 60 s by a simple agitation-based, surface-tension-driven fluidic self-assembly (FSA) technique with a yield of 99.88%. The creation of this level of large-scale, high-yield FSA of sub-100-µm chiplets was considered a significant challenge because of the low inertia of the chiplets. Our key finding in overcoming this difficulty is that the addition of a small amount of poloxamer to the assembly solution increases its viscosity which, in turn, increases liquid-to-chiplet momentum transfer. Our results represent significant progress towards the ultimate goal of low-cost, high-throughput manufacture of full-colour MicroLED displays by FSA.
RESUMO
PURPOSE: This study aimed to derive considerations for the enactment of nursing law by analyzing the trends and social perceptions of nursing law mentioned in major daily newspapers, cafes, and blogs. METHODS: Main texts and comments that included nursing law as a keyword were collected from major daily news and online postings from January 2021 to August 2022. The data collected through web crawling were analyzed using a TousFlux program used for big data analysis. RESULTS: During the period of study, the awareness level around nursing law enactment increased. In particular, public concern over nursing law enactment intensified due to the two political parties' policy pledges related to nursing law in January 2022 and the failure to introduce the nursing law to the national assembly judiciary committee in May 2022. Except in December 2021, public perception of nursing law enactment was generally favorable, with public opinion tilting more in favor of than against enactment. CONCLUSION: Public opinion should be considered when drafting and implementing the nursing law to make it easier for the people to understand what the law constitutes. In addition, it is necessary to pay attention to and continuously promote the relationship between medical care and nursing in the nursing law system of developed nations. Lastly, nursing law enactment can enhance nurses' retention intention and provide a sense of efficacy to medical services.
Assuntos
Análise de Dados , Percepção Social , Humanos , Intenção , PolíticasRESUMO
This study determines the importance of nurses' self-care by identifying its effects as a moderating variable on the relationships between perceived stress, job burnout, and retention intention in clinical nurses. Hence, 174 clinical nurses who worked at two university hospitals and one general hospital located in Seoul, South Korea, participated in this study. As the hospitals required the use of recruitment notices, convenience sampling methods were adopted to recruit volunteers. The data were collected using the perceived stress scale, the burnout assessment tool, the nurse retention index, and the self-care assessment worksheet. Descriptive statistics were used to analyze the general characteristics of participants, and t-test and analysis of variance were conducted for comparisons. Moderated multiple regression was conducted to verify the moderating effects of self-care on the relationships between perceived stress and retention intention and between job burnout and retention intention. The results revealed that the effect of perceived stress on retention intention and the moderating effect of self-care on the relationship between perceived stress and retention intention were not significant, whereas job burnout had a direct effect on retention intention, and self-care had a positive moderating effect on job burnout. Therefore, it is necessary to consider an instructional program on the importance of self-care and conduct campaign activities at the organizational level. Moreover, various support structures should be provided at the organizational level such that nurses can reduce their levels of job burnout.
RESUMO
To investigate the effects of their surface recovery and optical properties, extremely small sized (12 µm × 12 µm mesa area) red AlGaInP micro light emitting diodes ([Formula: see text] LED) were fabricated using a diluted hydrofluoric acid (HF) surface etch treatment. After the chemical treatment, the external quantum efficiencies (EQEs) of [Formula: see text]-LED at low and high injection current regions have been improved by 35.48% and 12.86%, respectively. The different phenomena of EQEs have a complex relationship between the suppression of non-radiative recombination originating from the etching damage of the surface and the improvement of light extraction of the sidewalls. The constant enhancement of EQE at a high injection current it is attributed to the expansion of the active region's sidewall surface area by the selective etching of AlInP layers. The improved EQE at a low injection current is related to the minimization of the surface recombination caused by plasma damage from the surface. High-resolution transmission electron microscopy (HR-TEM) revealed physical defects on the sidewall surface, such as plasma-induced lattice disorder and impurity contamination damage, were eliminated using chemical treatment. This study suggests that chemical surface treatment using diluted HF acid can be an effective method for enhancing the [Formula: see text]-LED performance.
RESUMO
Although conventional homoepitaxy forms high-quality epitaxial layers1-5, the limited set of material systems for commercially available wafers restricts the range of materials that can be grown homoepitaxially. At the same time, conventional heteroepitaxy of lattice-mismatched systems produces dislocations above a critical strain energy to release the accumulated strain energy as the film thickness increases. The formation of dislocations, which severely degrade electronic/photonic device performances6-8, is fundamentally unavoidable in highly lattice-mismatched epitaxy9-11. Here, we introduce a unique mechanism of relaxing misfit strain in heteroepitaxial films that can enable effective lattice engineering. We have observed that heteroepitaxy on graphene-coated substrates allows for spontaneous relaxation of misfit strain owing to the slippery graphene surface while achieving single-crystalline films by reading the atomic potential from the substrate. This spontaneous relaxation technique could transform the monolithic integration of largely lattice-mismatched systems by covering a wide range of the misfit spectrum to enhance and broaden the functionality of semiconductor devices for advanced electronics and photonics.
RESUMO
Graphene nanoribbons (GNRs) have recently emerged as alternative 2D semiconductors owing to their fascinating electronic properties that include tunable band gaps and high charge-carrier mobilities. Identifying the atomic-scale edge structures of GNRs through structural investigations is very important to fully understand the electronic properties of these materials. Herein, we report an atomic-scale analysis of GNRs using simulated X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Tetracene with zigzag edges and chrysene with armchair edges were selected as initial model structures, and their XPS and Raman spectra were analyzed. Structurally expanded nanoribbons based on tetracene and chrysene, in which zigzag and armchair edges were combined in various ratios, were then simulated. The edge structures of chain-shaped nanoribbons composed only of either zigzag edges or armchair edges were distinguishable by XPS and Raman spectroscopy, depending on the edge type. It was also possible to distinguish planar nanoribbons consisting of both zigzag and armchair edges with zigzag/armchair ratios of 4:1 or 1:4, indicating that it is possible to analyze normally synthesized GNRs because their zigzag to armchair edge ratios are usually greater than 4 or less than 0.25. Our study on the precise identification of GNR edge structures by XPS and Raman spectroscopy provides the groundwork for the analysis of GNRs.
RESUMO
In this study, we employ a combination of various in-situ surface analysis techniques to investigate the thermally induced degradation processes in MAPbI3 perovskite solar cells (PeSCs) as a function of temperature under air-free conditions (no moisture and oxygen). Through a comprehensive approach that combines in-situ grazing-incidence wide-angle X-ray diffraction (GIWAXD) and high-resolution X-ray photoelectron spectroscopy (HR-XPS) measurements, we confirm that the surface structure of MAPbI3 perovskite film changes to an intermediate phase and decomposes to CH3I, NH3, and PbI2 after both a short (20 min) exposure to heat stress at 100 °C and a long exposure (>1 hour) at 80 °C. Moreover, we observe clearly the changes in the orientation of CH3NH3+ organic cations with respect to the substrate in the intermediate phase, which might be linked directly to the thermal degradation processes in MAPbI3 perovskites. These results provide important progress towards improved understanding of the thermal degradation mechanisms in perovskite materials and will facilitate improvements in the design and fabrication of perovskite solar cells with better thermal stability.
RESUMO
In situ near-edge X-ray absorption fine structure (NEXAFS) spectroscopy and density functional theory calculations were conducted to demonstrate the decomposition mechanism of propylene glycol methyl ether acetate (PGMEA) on a MnO2-CuO catalyst. The catalytic activity of MnO2-CuO was higher than that of MnO2 at low temperatures, although the pore properties of MnO2 were similar to those of MnO2-CuO. In addition, whereas the chemical state of MnO2 remained constant following PGMEA dosing at 150 °C, MnO2-CuO was reduced under identical conditions, as confirmed by in situ NEXAFS spectroscopy. These results indicate that the presence of Cu in the MnO2-CuO catalyst enables the release of oxygen at lower temperatures. More specifically, the released oxygen originated from the Mn-O-Cu moiety on the top layer of the MnO2-CuO structure, as confirmed by calculation of the oxygen release energies in various oxygen positions of MnO2-CuO. Furthermore, the spectral changes in the in situ NEXAFS spectrum of MnO2-CuO following the catalytic reaction at 150 °C corresponded well with those of the simulated NEXAFS spectrum following oxygen release from Mn-O-Cu. Finally, after the completion of the catalytic reaction, the quantities of lactone and ether functionalities in PGMEA decreased, whereas the formation of C=C bonds was observed.