Effects of background color and thickness on the optical properties of CAD-CAM resin-matrix ceramics.

STATEMENT OF PROBLEM: Information regarding the masking ability of computer-aided design and computer-aided manufacture (CAD-CAM) resin-matrix ceramic materials with different compositions is scarce. PURPOSE: The purpose of this in vitro study was to evaluate the effects of background color and thickness on the optical properties (color and translucency) of CAD-CAM resin-matrix ceramics. MATERIAL AND METHODS: Twelve rectangular specimens were fabricated at a different thickness (1, 1.5, and 2 mm) (n=12) from each of the resin-matrix ceramic materials: Shofu block (SB), Lava Ultimate (LU), CERASMART (CS), VITA ENAMIC (VE), Crystal Ultra (CU), and the VITABLOCS Mark II feldspathic ceramic (VB). The color of the specimens over amalgam, titanium, enamel, and dentin backgrounds was measured with a spectrophotometer, and the color differences (ΔE∗ab) were calculated by using the Commission Internationale de l'Eclairage (CIE) 76 formula. The difference in color of the specimen over the black and white backgrounds was used to calculate the translucency parameter (TP). ANOVA was used to statistically test whether material, background, and thicknesses influenced ΔE∗ab and TP values. Post hoc comparisons were performed to determine the significant difference among the groups (α=.05). RESULTS: The interaction with 2 between factors demonstrated that the material was a factor that significantly influenced ΔE∗ab (P<.001). The highest mean ±standard deviation of ΔE∗ab was recorded in the combination of VB material and 2-mm thickness (1.84 ±0.37), and the lowest with CS material with 1.5-mm thickness (0.47 ±0.24). The type of material and specimen thickness significantly influenced TP (P<.001). The highest and lowest mean ±standard deviation of TP were recorded for the 1-mm-thick CS (14.20 ±0.90) and 2-mm-thick SB (4.91 ±0.42) specimens, respectively. CONCLUSIONS: CERASMART resin-matrix ceramic and VITABLOCS Mark II feldspathic ceramic exhibited high and low masking abilities over the investigated background substrates, respectively. However, irrespective of the thickness, all study materials exhibited acceptable masking abilities.

Fracture Load of CAD/CAM Fabricated Cantilever Implant-Supported Zirconia Framework: An In Vitro Study.

The fracture resistance of computer-aided designing and computer-aided manufacturing CAD/CAM fabricated implant-supported cantilever zirconia frameworks (ISCZFs) is affected by the size/dimension and the micro cracks produced from diamond burs during the milling process. The present in vitro study investigated the fracture load for different cross-sectional dimensions of connector sites of implant-supported cantilever zirconia frameworks (ISCZFs) with different cantilever lengths (load point). A total of 48 ISCZFs (Cercon, Degudent; Dentsply, Deutschland, Germany) were fabricated by CAD/CAM and divided into four groups based on cantilever length and reinforcement of distal-abutment: Group A: 9 mm cantilever; Group B: 9 mm cantilever with reinforced distal-abutment; Group C: 12 mm cantilever; Group D: 12 mm cantilever with reinforced distal-abutment (n = 12). The ISCZFs were loaded using a universal testing machine for recording the fracture load. Descriptive statistics, ANOVA, and Tukey's test were used for the statistical analysis (p < 0.05). Significant variations were found between the fracture loads of the four ISCZFs (p = 0.000); Group-C and B were found with the weakest and the strongest distal cantilever frameworks with fracture load of 670.39 ± 130.96 N and 1137.86 ± 127.85 N, respectively. The mean difference of the fracture load between groups A (810.49 + 137.579 N) and B (1137.86 ± 127.85 N) and between C (670.39 ± 130.96 N) and D (914.58 + 149.635 N) was statistically significant (p = 0.000). Significant variations in the fracture load between the ISCZFs with different cantilever lengths and thicknesses of the distal abutments were found. Increasing the thickness of the distal abutment only by 0.5 mm reinforces the distal abutments by significantly increasing the fracture load of the ISCZFs. Therefore, an increase in the thickness of the distal abutments is recommended in patients seeking implant-supported distal cantilever fixed prostheses.

In Vitro Evaluation of Translucency and Color Stability of CAD/CAM Polymer-Infiltrated Ceramic Materials after Accelerated Aging.

PURPOSE: To investigate and compare the translucency and color stability of a newly introduced polymer-infiltrated ceramic network (PICN) material (Crystal Ultra) to those of clinically well-established restorative materials. MATERIALS AND METHODS: A total of 80 specimens measuring (12 × 14 × 1 mm ± 0.05 mm) were prepared from five CAD/CAM (IPS e.max (IPS), Lava Ultimate (LU), Cerasmart (CS), Vita Enamic (VE), Crystal Ultra (CU)) high translucency (HT) blocks in A2 or equivalent shades. Specimens were randomly allocated into two groups (A and B) (n = 8), and were subjected to 5,000 thermal-cycles (TC). This was followed by one-week immersion of group A specimens in coffee (staining) solution and group B specimens in distilled water. Following immersion, the specimens from both groups were further subjected to 5,000 TC. A spectrophotometer was used to measure the translucency parameter (TP) and color change (ΔE00 ) of the samples using CIELAB color coordinates at baseline, after 5,000 TC, following immersion, and after further 5,000 TC. Color stability was evaluated using the CIEDE2000 formula. Data were analyzed by non-parametric tests (α = 0.05). RESULTS: The TP values of the CAD/CAM materials ranged from 18.0-22.0. Following the initial TC, the changes in TP values were significant for VE (p = 0.012). Coffee immersion and further TC significantly impacted the TP values of PICN (VE and CU) materials compared to glass- ceramics (IPS), and resin nanoceramic (CS and LU) materials (p = 0.012). The comparison between CAD/CAM materials at different intervals showed a significant difference in the TP values (p < 0.01). The materials showed perceptible color changes following the initial TC except for PICN materials which demonstrated acceptable color changes. The major color difference was noticed for the resin nanoceramic specimens immersed in coffee; LU and CS showed higher color changes (ΔE00 = 2.45 and 2.09, respectively) than VE and CU (ΔE00 < 1.8). CONCLUSIONS: The translucency of the newly introduced Crystal Ultra PICN material was low compared to the resin nanoceramics and lithium disilicate glass-ceramic. The Crystal Ultra material exhibited better color stability compared to resin nanoceramics, but higher color change when compared with Vita Enamic PICN and lithium disilicate glass-ceramic CAD/CAM materials.

The Direct Cytotoxic Effects of Different Hemostatic Agents on Human Gingival Fibroblasts.

PURPOSE: To evaluate the cytotoxic effects of different hemostatic agents (including Expasyl) on human gingival fibroblasts (HGFs) in vitro. MATERIALS AND METHODS: HGFs were cultured and exposed to either no medicament treatment or 1:200 dilution of six different hemostatic agents (Hemox-A, Hemodent, Astringedent, Vicostat, Expasyl, 3M ESPE) for 2, 5, 10 minutes, 1 hour, and 24 hours. Toxicity to HGFs was determined by lactate dehydrogenase activity (LDH) and colorimetric (WST-1) assays. Two-tailed t-test was used for statistical analyses with α level set at 0.05. RESULTS: The group-by-time interactions were significant for the LDH and WST-1 assays (p < 0.001). Evaluation of the cytotoxic effect of different hemostatic agents at different incubation time intervals on the cell membrane damage revealed that Astringedent showed the highest cytotoxic effect on HGFs compared to other agents with regards to untreated negative control cells at all incubation time intervals (p < 0.001). On the other hand, Expasyl showed the least cytotoxic effect with significant differences at 5 minutes and 1 hour (p < 0.001) in comparison to other agents. CONCLUSIONS: LDH and WST-1 assays of hemostatic agents showed significant cytotoxic effect on HGFs at different time intervals. The data suggest that the risk for permanent tissue damage might be less significant when Expasyl is used during final impression procedure compared to when Astringedent is used.

Comparison of Clinical, Radiographic, and Immunologic Inflammatory Parameters around Crestally and Subcrestally Placed Dental Implants: 5-Year Retrospective Results.

PURPOSE: To compare changes in clinical (bleeding on probing [BOP] and probing pocket depth [PPD]), radiographic (crestal bone loss [CBL]), and immunologic inflammatory (interleukin-1beta [IL-1ß] and matrix metalloproteinase-9 [MMP-9]) parameters around crestally and subcrestally placed dental implants 5 years after implant placement. MATERIALS AND METHODS: Fifty-two patients were divided into 2 groups: group 1 (n = 27): patients with single implants placed approximately 2 mm below the alveolar crest; group 2 (n = 25): patients with single implants placed at bone level. In both groups, peri-implant BOP, PPD, and CBL were measured, and levels of IL-1ß and MMP-9 were determined in duplicates using enzyme-linked immunosorbent assay. Full-mouth debridement was performed biannually in both groups. Statistical analysis was performed using the Mann-Whitney U test (significance set at p < 0.05). RESULTS: All measurements in groups 1 and 2 were performed 5.3 ± 0.2 and 5.2 ± 0.1 years after implant placement, respectively. The mean CBL was 1.2 ± 0.2 mm and 1.4 ± 0.2 mm in groups 1 and 2, respectively. There was no significant difference in mean BOP, PPD, CBL and in levels of IL-1ß, and MMP-9 among implants in both groups. CONCLUSION: Clinical, radiographic, and immunologic inflammatory parameters are comparable around crestally and subcrestally placed single dental implants up to 5 years after placement. The depth of implant placement appears to have no effect on clinical status and performance of single dental implants.

The direct cytotoxic effects of medicaments used in endodontic regeneration on human dental pulp cells.

AIM: The purpose of this in vitro study was to evaluate the effects of intracanal medicaments commonly used in endodontic regeneration on the survival of human dental pulp cells (DPCs). METHODS: DPCs were cultured and exposed to either no medicament treatment or low concentrations (0.3-5 mg ml(-1) ) of calcium hydroxide [Ca(OH)2 ], triple antibiotic paste (TAP), or double antibiotic paste (DAP) for 3 days. After that, toxicity to the DPCs was determined by lactate dehydrogenase activity assays (LDH) and cell proliferation was measured by colorimetric assays (WST-1). Two-way anova followed by Fisher's protected least significant differences was used for statistical analyses (α = 0.05). RESULTS: The group-by-concentration interactions were significant for the LDH and WST-1 assays (P < 0.0001). For the LDH assays, only the highest tested concentration (5 mg ml(-1) ) of Ca(OH)2 and TAP caused significant toxicity to the DPCs compared with the untreated control, while four tested concentrations of DAP (0.5, 1, 2.5, and 5 mg ml(-1) ) caused significant toxicity to the DPCs compared with the untreated control. For the WST-1 assays, the highest concentrations that did not negatively affect the proliferation rate of DAP, TAP and Ca(OH)2 were 0.3, 2, and 2.5 mg ml(-1) , respectively. CONCLUSION: The low concentrations of intracanal medicaments tested in this study were not cytotoxic in cultured cells. However, these concentrations are much lower than the concentrations that have been advocated in endodontic regeneration. Furthermore, the negative effects of TAP on DPCs were detected at lower concentrations by using the WST-1 assays than by measuring the LDH release.

Assessing the effect of Artemisia sieberi extracts on surface roughness and candida growth of digitally processed denture acrylic materials.

BACKGROUND: Denture stomatitis, frequently encountered, is generally addressed symptomatically, with limited exploration of preventive approaches involving antifungal medicinal plants. OBJECTIVE: This study assessed the impact of Artemisia sieberi extracts on the candida growth of conventional and digitally processed acrylic materials. METHOD: Thirty acrylic resin discs (3 mm thickness × 10 mm diameter) were prepared by conventional or CAD/CAM technology (milling and 3D printing). The resin discs were exposed to simulated brushing, thermocycling, and immersion in Artemisia sieberi extract for 8 hours. The surface roughness of the discs was assessed at baseline and after immersion in Artemisia sieberi extract. Candida growth was quantified through colony-forming units (CFU/mL). Data was analyzed using SPSS v.22 (α⩽ 0.05). RESULTS: Irrespective of the material type, the post-immersion surface roughness was significantly higher compared to pre-immersion values (p< 0.05). Candida growth was significantly higher in conventional acrylic materials than digitally fabricated acrylics (p< 0.05). At × 3, Ra and CFU were found to be moderately positive and non-significantly correlated (R= 0.664, p= 0.149). At × 4, Ra and CFU were found to be weak positive and non-significantly correlated (R= 0.344, p= 0.503). CONCLUSION: Artemisia sieberi extracts had a notable impact on digitally fabricated denture acrylics, reducing candida albicans growth compared to conventional heat-cured acrylic. This suggests a potential role for these extracts in improving denture hygiene and preventing denture stomatitis, particularly in the context of digitally fabricated dentures.

Effects of interim acrylic resins on the expression of cytokines from epithelial cells and on collagen degradation.

STATEMENT OF PROBLEM: Interim acrylic resins release agents that alter cytokine expression in the surrounding tissues, which could alter extracellular matrix degradation. PURPOSE: The purpose of the study was to evaluate the responses of human epidermal keratinocytes to eluates of interim acrylic resins in regards to cytokine expression and cell-mediated collagen degradation. MATERIAL AND METHODS: Specimens of 4 different interim acrylic resins (HI-I, Jet Acrylic, SNAP acrylic, and Protemp Plus) were placed in Epilife medium for 48 hours and the eluates collected. The cells were incubated for 72 hours in nontoxic concentrations of the eluates. Cytotoxicity was evaluated with lactate dehydrogenase assays and cytokine expression with cytokine antibody arrays. Collagen degradation was determined with a collagen type I assay. The experiments were performed 3 times. Data were analyzed with 1-way and mixed-model ANOVA (α=.05). RESULTS: None of the eluates were cytotoxic. Cytokine expression from the heat-activated polymethyl methacrylate resin group was significantly less for interleukin-3, but significantly greater for interlukin-7. Expression for the chemically activated polymethyl methacrylate resin group was significantly less for growth-regulated oncogene-α, interleukin-1α, and interleukin-3. Expression for the chemically activated polyethyl methacrylate resin group was significantly less for interleukin-1α and interleukin-3, but significantly greater for interleukin-13 and monocytes chemoattractant protein-3. The cytokine expression induced by chemically activated bis-acryl composite resin was significantly greater for granulocyte-macrophage colony stimulating factor, interleukin-7, and monocytes chemoattractant protein-3, but significantly less for growth-regulated oncogene-α. Collagen degradation was not significantly different in any of the groups. CONCLUSIONS: The eluates used were not cytotoxic and did not induce cell-mediated collagen degradation. Some significant changes in cytokine expression were noted.

Release and MMP-9 Inhibition Assessment of Dental Adhesive Modified with EGCG-Encapsulated Halloysite Nanotubes.

Degradation of the collagen fibrils at the dentin-resin interface by the enzymatic activity of matrix metalloproteinases (MMPs) has been known to permit some dental restoration complications, such as microleakage, secondary caries, and, ultimately, restoration failures. This study aimed to evaluate a modified adhesive by adding an MMP inhibitor from green tea extract with and without nanotube encapsulation to sustain the drug release. Epigallocatechin-3-gallate (EGCG) and Halloysite nanotubes (HNTs) were prepared to produce three variant combinations of modified adhesive (EGCG, EGCG-encapsulated HNT, and EGCG-free HNT). The drug loading efficiency and EGCG release over time were evaluated using UV-vis spectrometry. MMP-mediated ß-casein (BCN) cleavage rate assays were used to determine the ability of the EGCG in eluates of the adhesive to inhibit MMP-9 activities. For up to 8 weeks, HNT encapsulation reduced release to a statistically significant level. MMP-mediated ß-casein cleavage rate assays showed a significant decrease for the EGCG groups compared to the non-EGCG adhesive groups. Furthermore, the use of HNT for EGCG encapsulation to modify a dental adhesive helped slow down the rate of EGCG release without impacting its MMP inhibitory capabilities, which may help to maintain the dentin-resin interface's integrity over the long term after dental restoration placement.

Microhardness and Gloss of a New CAD/CAM Hybrid Material Following Accelerated Aging and Coffee Immersion.

PURPOSE: To evaluate and compare the effect of accelerated aging and coffee immersion on the microhardness and gloss of a new computer-aided design and computer-aided manufacturing (CAD/CAM) hybrid material (Crystal Ultra) to those of contemporary restorative materials. MATERIALS AND METHODS: A total of 160 specimens (12 × 14 × 1 mm ± 0.05 mm) were obtained from IPS e.max (IPS), VITA Enamic (VE), Crystal Ultra (CU), Lava Ultimate (LU), and CeraSmart (CS) high-translucency CAD/CAM blocks. The Vickers microhardness and gloss of the specimens were determined after thermocycling and coffee immersion. Data analysis was performed using SPSS (α = .05). RESULTS: IPS and CS specimens exhibited the highest (572.66 ± 11.30) and lowest (61.92 ± 3.91) microhardness, respectively. The highest gloss was observed with IPS specimens (3.31 ± 0.32), and LU specimens showed the lowest gloss (2.33 ± 0.06). A significant difference in gloss was observed between the materials at all measurement intervals (P < .01), except at T0 (P = .43). IPS specimens showed no significant changes in either group at any measurement interval. CONCLUSIONS: The microhardness and gloss of the new CU material were comparable to those of the tested contemporary hybrid restorative materials. Glass-ceramic showed superior hardness and gloss compared to hybrid restorative materials. Accelerated aging with thermocycling and staining significantly affected the microhardness and gloss of all tested CAD/CAM materials.

Effect of Adding Silver-Doped Carbon Nanotube Fillers to Heat-Cured Acrylic Denture Base on Impact Strength, Microhardness, and Antimicrobial Activity: A Preliminary Study.

Poly (methyl methacrylate) (PMMA), is an acrylic polymer substance that is mostly used for denture base applications. The purpose of this laboratory study was to investigate the effect of adding 0.05 wt.% Ag-doped carbon nanotubes (CNT) to PMMA-based (PMMA and MMA) denture base material on the impact strength, microhardness, and antimicrobial activity. A total of 60 heat-cured acrylic resin specimens were prepared. The specimens were randomly divided into two main groups (n = 30/group), according to the powder used: (a) control group, using heat-cured PMMA; (b) treatment group, using a powder prepared by blending 0.05 wt.% silver-doped CNT nanoparticles with heat-cured PMMA. The impact strength, microhardness and anticandidal activity for each group were assessed via the Charpy, Vickers and agar diffusion tests, respectively (n = 10/test for each subgroup). Data were analyzed using independent-sample t-tests (p ≤ 0.05). The results of the impact strength test revealed that the treated heat-cured PMMA-MMA with Ag-doped CNT (2.2 kJ/mm2) was significantly higher than that of the control heat-cured PMMA (1.6 kJ/mm2). Similarly, the Vickers microhardness of the treatment group (52.7 VHN) was significantly higher than that of the control group (19.4 VHN). Regarding the agar diffusion test, after 24 h of incubation, the treated heat-cured PMMA with the Ag-doped CNT exhibited significantly higher anticandidal activity than that of the control group. Therefore, Ag-doped carbon nanotubes could be considered as promising fillers for the dental heat-cured acrylic resin to improve the resistance of the resultant denture against sudden fractures, scratching, and candida invasion.

Efficacy of Denture Cleansers on Microbial Adherence and Surface Topography of Conventional and CAD/CAM-Processed Denture Base Resins.

This study assessed the efficacy of five denture cleansers on the microbial adherence and surface topography of conventional and CAD/CAM denture base resins. Acrylic resin discs were fabricated using conventional, milling, and 3D printing methods (N = 180). The discs were contaminated with dual species of Candida albicans and Streptococcus mutans biofilm for 72 h and then disinfected with either of the denture cleansers (Fittydent cleansing tablets, 2% Chlorhexidine gluconate, 0.2% Chlorhexidine gluconate, 0.5% sodium hypochlorite, and 1% sodium hypochlorite (n = 10). Distilled water served as the control group. The colony-forming units of the microorganisms were calculated, followed by post-treatment surface roughness. Data were statistically analyzed using one-way ANOVA, paired t-test, and post hoc Tukey HSD test (α = 0.05). Among the denture cleansers, 2% Chlorhexidine gluconate, 0.5% sodium hypochlorite, and 1% sodium hypochlorite had the best cleansing effect on the resin discs and demonstrated zero growth of colonies for both the species. Comparing the material groups, the 3D-processed discs showed higher colony-forming units followed by the conventional and CAD/CAM milled group. The highest surface roughness was demonstrated by the 3D-printed discs (0.690 ± 0.08 µm), followed by the conventional (0.493 ± 0.11 µm) and the milled groups (0.301 ± 0.08 µm). The tested chemical denture cleansers affected the Candida albicans and Streptococcus mutans adhesion compared to control discs immersed in distilled water. The clinician may recommend to their patient to use 2% chlorhexidine gluconate for the disinfection of CAD/CAM PMMA denture base materials.

Microhardness and gloss of a new CAD-CAM hybrid material following accelerated aging and coffee immersion.

PURPOSE: To evaluate and compare the effect of accelerated aging and coffee immersion on the microhardness and gloss of a new CAD/CAM hybrid material (Crystal Ultra) to those of contemporary restorative materials. MATERIALS AND METHODS: A total of 160 specimens (12 x 14 x 1 mm ± 0.05 mm) were obtained from (IPS e.max [IPS], VITA Enamic [VE], Crystal Ultra [CU], Lava Ultimate [LU], and CeraSmart [CS]) high-translucency CAD/CAM blocks. The Vickers microhardness and gloss of the specimens were determined following thermocycling and coffee immersion. Data analysis was performed using SPSS (α = .05). RESULTS: IPS and CS specimens exhibited the highest (572.66 ± 11.30) and lowest (61.92 ± 3.91) microhardness, respectively. The highest gloss was observed with IPS specimens (3.31 ± 0.32), and LU specimens showed the lowest gloss (2.33 ± 0.06). A significant difference in gloss was observed between the materials at all measurement intervals (P < .01), except at T0 (P = .43). IPS specimens showed no significant changes in either group at any measurement interval. CONCLUSION: The microhardness and gloss of the new CU material were comparable to those of the tested contemporary hybrid restorative materials. Glass-ceramic showed superior hardness and gloss compared to hybrid restorative materials. Accelerated aging by thermocycling and staining significantly affected the microhardness and gloss of all the tested CAD/CAM materials.

Effect of Different Wax Pattern Manufacturing Techniques on the Marginal Fit of Lithium Disilicate Crowns.

Purpose: The present study evaluated the marginal gap of lithium disilicate crowns fabricated through three different wax pattern techniques; Conventional, Milling and 3D-printing. Materials and Methods: Thirty stone models were replicated from a stainless-steel model representing a prepared tooth; ten were sent to make conventional wax patterns while the remaining were sent to a digital dental scanner. The computer aided design was completed and STL (Standard Tessellation Language) files were sent to either milling or 3D-printing machines. All wax patterns (n = 30) were pressed, and a stabilizing instrument was used to secure the crowns on the master model. The marginal gap was measured at 18 points for each crown using a digital microscope (µm) (n = 540) and compared using One-way ANOVA (p ≤ 0.05). Results: There was a significant difference in the marginal gap value between all three groups (p < 0.01) where the milled group showed the least mean gap (28.87 ± 30.18 µm), followed by 3D printed (47.85 ± 27.44 µm), while the highest mean marginal gap was found in the conventional group (63.49 ± 28.05 µm). Conclusion: Milled and 3D-printed wax patterns produced better fitting crowns compared to conventional techniques.

Effect of aging and mechanical brushing on surface roughness of 3D printed denture resins: A profilometer and scanning electron microscopy analysis.

BACKGROUND: The use of 3D printed material in the dental field is gaining tremendous attention. However, studies related to 3D printed denture resins are scarce and need consideration before their inclusion in routine clinical practice. OBJECTIVE: This study aimed to assess the surface roughness (Ra) of 3D printed denture resins following aging and mechanical brushing. METHODS: Forty round samples (diameter, 10 mm and thickness, 3 mm) were fabricated from two 3D printed (DentaBASE and Denture 3D+) and one conventional polymethylmethacrylate (PMMA) denture materials. The samples were thermo-cycled, subjected to mechanical brushing, and later immersed in either artificial saliva (AS), coffee, cola, or lemon juice (n= 10) to simulate one and two years of oral use. Surface roughness (Ra) was determined using a non-contact profilometer and scanning electron microscope was used for qualitative analysis. The data was analyzed using SPSS v.20 (α= 0.05). RESULTS: Denture 3D+ demonstrated highest mean Ra (1.15 ± 0.28 µm), followed by PMMA (0.99 ± 0.50 µm) and DentaBASE (0.81 ± 24). The difference in mean Ra between the materials was statistically non-significant (P= 0.08). Amongst the different beverages used, the highest Ra was observed for samples immersed in lemon juice (1.06 ± 0.40 µm) followed by cola (1.04 ± 0.46 µm) and coffee (0.98 ± 0.40 µm), respectively. The lowest Ra was observed for samples immersed in AS (0.85 ± 0.24 µm). CONCLUSION: The surface roughness of 3D printed denture resins was comparable with that of conventional PMMA resins. Denture 3D+ demonstrated the highest mean roughness, followed by PMMA and DentaBASE.

Influence of Acidic Environment on the Hardness, Surface Roughness and Wear Ability of CAD/CAM Resin-Matrix Ceramics.

This study aimed to measure the effect of storage environment on the hardness, surface roughness and wear ability of CAD/CAM resin-matrix ceramics. A total of 200 rectangular-shaped specimens were obtained by sectioning 5 CAD/CAM blocks; Crystal Ultra (CU), Vita Enamic (VE), Lava Ultimate (LU), Cerasmart (CS) and Vita blocks Mark II (MII). Microhardness and surface roughness were measured at baseline and after 7 days of immersion either in saliva or cola (n = 10). The wear ability of the CAD/CAM materials against steatite-ceramics antagonist was determined using a chewing simulator. The data were statistically analyzed using factorial ANOVA followed by post hoc Bonferroni multiple comparison tests (p < 0.05). The independent factors significantly influenced the microhardness and surface roughness (p < 0.05). The highest VHN was observed in MII at baseline (586.97 ± 13.95), while CU showed the lowest VHN after 7 days of immersion in cola (68.3 ± 1.89). On the contrary, the highest Ra was observed after 120,000 chewing cycles for the VE specimens (1.09 ± 0.43 µm) immersed in cola, while LU showed the lowest Ra at baseline (0.07 ± 0.01 µm). The highest % mass loss of the antagonist was observed with MII immersed in cola (1.801%), while CS demonstrated the lowest % mass loss of 0.004% and 0.007% in AS and cola, respectively. This study confirms that the surface properties of tested CAD/CAM materials are susceptible to degradation in an acidic environment except for hardness and wear of CS material.

A simple technique to reduce the risk of irreversible gingival recession after the final impression.

The chemicomechanical method is the most common tissue displacement technique used to facilitate the final impression for fixed dental prostheses. The article describes a simple technique to minimize the risk of developing gingival irreversible recession because of tissue displacement cords.

Use of temporary abutment to assess implant osseointegration before final impression: A case report.

In implant dentistry, a temporary abutment, either plastic or metal, also called an implant cylinder, is used to construct a provisional restoration. This provisional restoration can be cemented on or integrated with a temporary abutment for a screw-retained prosthesis. It can be further used as a diagnostic tool to evaluate esthetics and promote tissue healing around implants. After achieving osseointegration of the implant with the adjacent bone and a proper soft tissue profile, both the temporary abutment and the prosthesis can be replaced with permanent ones. In the present case report, a simple technique using a temporary abutment was utilized for the assessment of implant osseointegration before making the final impression. In this study, we discuss the advantages of this method over other methods. It is impossible to verify the stability of the implant at all stages of implant placement; however, the clinical procedure explained in the case report is easy to apply and provides good results.

Role of antimicrobial photodynamic therapy in reducing whole salivary oral yeasts colonization in type-2 diabetic and non-diabetic patients with and without dental implants.

OBJECTIVE: The aim was to assess the impact of antimicrobial photodynamic therapy (aPDT) in reducing whole salivary oral yeasts colonization in type-2 diabetic and non-diabetic patients with dental implants. METHODS: Type-2 diabetic and self-reported non-diabetic patients were included. Participants were divided into the following groups: Group-1: Type-2 diabetic patients with dental implants; Group-2: Non-diabetic patients with dental implants; Group-3: Type-2 diabetic patients without dental prostheses; Group-4: Non-diabetic patients without dental prostheses. In each group, participants were subdivided into 2-sub-groups. In the test-subgroup, participants received routine oral hygiene maintenance instructions (OHMI) and underwent full mouth disinfection using aPDT; and in the control-group, participants received OHMI alone. Unstimulated whole saliva samples were collected, hemoglobin A1c levels were measured and yeast colonization was assessed at baseline and at 3-months' follow-up in all groups. Sample-size estimation was done and group-comparisons were done. P-values <0.01 were considered statistically significant. RESULTS: At baseline, the mean oral yeasts colonization was significantly higher among patients in Group-1 (P < 0.001) and 3 (P < 0.001) compared with individuals in groups 2 (P < 0.001) and 4 (P < 0.001). At baseline and at 3-months of follow-up, the mean HbA1c levels and oral yeasts colonization were significantly higher among patients in Group-1 (P < 0.001) and 3 (P < 0.001) compared with individuals in groups 2 (P < 0.001) and 4 (P < 0.001). CONCLUSION: In the short-term, routine OHMI with adjunct aPDT is more effective in reducing whole salivary oral yeasts counts than OHMI alone in patients with and without dental implants.

Soft Denture Liner Adhesion to Conventional and CAD/CAM Processed Poly(Methyl Methacrylate) Acrylic Denture Resins-An In-Vitro Study.

This study aimed to evaluate the airborne-particle abrasion surface treatment effects on the tensile bond strength (TBS) between resilient denture liner and CAD/CAM or conventional heat polymerized poly (methyl methacrylate) (PMMA) acrylic denture resins. A total of 48 dumbbell-shaped specimens (70 mm in total length, and 12 mm and 7 mm in diameter at the thickest and thinnest section, respectively) were prepared from CAD/CAM and conventional acrylic resins. Before relining with denture liner, 12 specimens from each material were surface-treated by 110 µm Al2O3 airborne-particle abrasion, and the remaining specimens served as control (no treatment). Following relining, all the specimens were aged by thermal cycling (1000 cycles, 5-55 °C). The TBS of denture liner to acrylic denture resins was tested in a universal testing apparatus at a 5 mm/min crosshead speed. The debonded surfaces were visually examined for the failure modes. ANOVA and multiple comparisons posthoc analysis tests were applied to determine the significant difference in TBS between the study groups (α = 0.05). A significant difference in TBS was observed between the control and surface treated groups (p < 0.001) for both acrylic resins materials. However, there was no statistically significant difference in bond strength between the acrylic resins materials (p = 0.739). Surface treatment with airborne-particle abrasion demonstrated increased TBS of the soft denture liners to acrylic resins. The TBS of conventional and CAD/CAM acrylic resins to soft denture liners were not considerably different.