Is the collateral circulation pattern in the hard palate affected by cleft deformity?

OBJECTIVES: To evaluate the influence of collateral vascularization on surgical cleft palate closure and deformities. MATERIALS AND METHODS: Corrosion casting was performed using red-colored acrylic resin in twelve fresh adult cadavers with a normal hard palate. Additionally, white-colored barium sulfate was injected into a fetus with a unilateral complete cleft palate, and layer-by-layer tissue dissection was performed. Both substances were injected into the external carotid arteries. Corrosion casting involved dissolving the soft and hard tissues of the orofacial area utilizing an enzymatic solution. RESULTS: In normal palates, bilateral intraosseous infraorbital arteries formed a network in the premaxilla with the intraosseous nasopalatine- and greater palatine arteries (GPAs). The perforating GPAs anastomosed with the sphenopalatine artery sub-branches. Bilateral extraosseous GPA anastomoses penetrated the median palatine suture. Complex vascularization in the retrotuberal area was detected. In the cleft zone, anastomoses were omitted, whereas in the non-cleft zone, enlarged GPAs were distributed along the cleft edges and followed the anatomical course anteriorly to initiate the network with facial artery sub-branches. CONCLUSIONS: The anatomical subunits of the palate exhibited distinct anastomosis patterns. Despite omitted anastomoses with collateral circulation in the cleft zone, arteries maintained their anatomical pattern as seen in the normal specimen in the non-cleft zone. CLINICAL RELEVANCE: Based on the findings in normal- and cleft palates, surgeons may expect developed anastomosis patterns in the non-cleft zone. Due to the lack of microcirculation in the cleft zone, the existent anastomoses should be maintained as much as possible by the surgical technique. This applies anteriorly in the incisive canal territory, alveolar ridges, and posteriorly in the retrotuberal area.

Pre-Epiglottic Baton Plate in Newborns With Pierre Robin Sequence: Revisiting the Practical Workflow.

We demonstrate pre-epiglottic baton plate as non-invasive treatment modality for initial airway management in newborns with Pierre Robin Sequence. A case example illustrates management of upper airway obstruction and feeding using digital technology to facilitate customization. Laryngoscope, 2024.

Comparative study on cleft palate morphology after passive presurgical plate therapy in unilateral cleft lip and palate.

BACKGROUND: Presurgical plate therapy has been widely accepted as a treatment prior to palatal cleft closure. The effects of passive presurgical plate therapy on cleft morphology prior to single-stage unilateral cleft lip and palate (UCLP) repair were quantified. PATIENTS AND METHODS: We compared the dimensions of cleft width and cleft area (true cleft and palatal cleft) measured preoperatively at 2 European cleft centers. Center A performed single-stage UCLP repair in 8-month-old infants without any presurgical orthopedic treatment. Center B initiated passive presurgical plate therapy immediately after the birth of the neonates, followed by single-stage UCLP repair at 8 months of age. RESULTS: We included 28 patients with complete UCLP from Center A and 12 patients from Center B. The average anterior width of the true cleft before surgery was significantly smaller in infants at Center B than that in Center A (p = 0.001) with 95% confidence interval of (1.8, 5.7) mm, but the average posterior width was similar in the 2 groups. The mean presurgical true cleft area amounted to 106.8 mm2 (SD = 42.4 mm2) at Center A and 71.9 mm2 (SD = 32.2 mm2) at Center B, with a confidence interval for the difference being (9.8, 60.1) mm2. This corresponded to a 32.7% reduction of the true cleft area when passive presurgical plate therapy was used for the first 8 months of the infants' life. CONCLUSION: Passive presurgical plate therapy in UCLP significantly reduced the cleft area. Implications for the subsequent surgical outcome might depend on the surgical technique used.

Cleft lip and palate surgery simulator: Open source simulation model.

Objective: Cleft lip and palate is the most common craniofacial birth anomaly and requires surgery in the first year of life. However, craniofacial surgery training opportunities are limited. The aim of this study was to present and evaluate an open-source cleft lip and palate hybrid (casting and three-dimensional (3D) printing) simulation model which can be replicated at low cost to facilitate the teaching and training of cleft surgery anatomy and techniques. Design: The soft tissue component of the cleft surgery training model was casted using a 3D printed 5-component mold and silicone. The bony structure was designed to simulate the facial anatomy and to hold the silicone soft tissue. Setting: Two groups, one group of trainees and one group of expert surgeons, at University Hospital Basel in Switzerland and Pontifical Catholic University of Chile in Santiago, Chile, tested the cleft lip and palate simulation model. Participants completed a Likert-based face and content validity questionnaire to assess the realism of the model and its usefulness in surgical training. Results: More than 70 % of the participants agreed that the model accurately simulated human tissues found in patients with unilateral cleft lip and palate. Over 60 % of the participants also agreed that the model realistically replicated surgical procedures. In addition, 80-90 % of the participants found the model to be a useful and appropriate tool for teaching the anatomy and surgical techniques involved in performing unilateral cleft lip and palate repair. Conclusion: This open-source protocol provides a cost-effective solution for surgeons to introduce the cleft morphology and surgical techniques to trainees on a regular basis. It addresses the current financial barrier that limits access to commercially available models during the early stages of surgeon training prior to specialization in the field.