Combining Coagulation and Electrocoagulation with UVA-LED Photo-Fenton to Improve the Efficiency and Reduce the Cost of Mature Landfill Leachate Treatment.

This study focused on the reduction of the treatment cost of mature landfill leachate (LL) by enhancing the coagulation pre-treatment before a UVA-LED photo-Fenton process. A more efficient advanced coagulation pretreatment was designed by combining conventional coagulation (CC) and electro-coagulation (EC). Regardless of the order in which the two coagulations were applied, the combination achieved more than 73% color removal, 80% COD removal, and 27% SUVA removal. However, the coagulation order had a great influence on both final pH and total dissolved iron, which were key parameters for the UVA-LED photo-Fenton post-treatment. CC (pH = 5; 2 g L-1 of FeCl36H2O) followed by EC (pH = 5; 10 mA cm-2) resulted in a pH of 6.4 and 100 mg L-1 of dissolved iron, whereas EC (pH = 4; 10 mA cm-2) followed by CC (pH = 6; 1 g L-1 FeCl36H2O) led to a final pH of 3.4 and 210 mg L-1 dissolved iron. This last combination was therefore considered better for the posterior photo-Fenton treatment. Results at the best cost-efficient [H2O2]:COD ratio of 1.063 showed a high treatment efficiency, namely the removal of 99% of the color, 89% of the COD, and 60% of the SUVA. Conductivity was reduced by 17%, and biodegradability increased to BOD5:COD = 0.40. With this proposed treatment, a final COD of only 453 mg O2 L-1 was obtained at a treatment cost of EUR 3.42 kg COD-1.

Industrial Application of Nanocelluloses in Papermaking: A Review of Challenges, Technical Solutions, and Market Perspectives.

Nanocelluloses (NC) increase mechanical and barrier paper properties allowing the use of paper in applications actually covered by other materials. Despite the exponential increase of information, NC have not been fully implemented in papermaking yet, due to the challenges of using NC. This paper provides a review of the main new findings and emerging possibilities in this field by focusing mainly on: (i) Decoupling the effects of NC on wet-end and paper properties by using synergies with retention aids, chemical modification, or filler preflocculation; (ii) challenges and solutions related to the incorporation of NC in the pulp suspension and its effects on barrier properties; and (iii) characterization needs of NC at an industrial scale. The paper also includes the market perspectives. It is concluded that to solve these challenges specific solutions are required for each paper product and process, being the wet-end optimization the key to decouple NC effects on drainage and paper properties. Furthermore, the effect of NC on recyclability must also be taken into account to reach a compromise solution. This review helps readers find upscale options for using NC in papermaking and identify further research needs within this field.

In Situ Production and Application of Cellulose Nanofibers to Improve Recycled Paper Production.

The recycled paper and board industry needs to improve the quality of their products to meet customer demands. The refining process and strength additives are commonly used to increase mechanical properties. Interfiber bonding can also be improved using cellulose nanofibers (CNF). A circular economy approach in the industrial implementation of CNF can be addressed through the in situ production of CNF using side cellulose streams of the process as raw material, avoiding transportation costs and reducing industrial wastes. Furthermore, CNF fit for use can be produced for specific industrial applications.This study evaluates the feasibility of using two types of recycled fibers, simulating the broke streams of two paper machines producing newsprint and liner for cartonboard, to produce in situ CNF for direct application on the original pulps, old newsprint (ONP), and old corrugated container (OCC), and to reinforce the final products. The CNF were obtained by 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO)-mediated oxidation and homogenization at 600 bar. Handsheets were prepared with disintegrated recycled pulp and different amounts of CNF using a conventional three-component retention system. Results show that 3 wt.% of CNF produced with 10 mmol of NaClO per gram of dry pulp improve tensile index of ONP ~30%. For OCC, the same treatment and CNF dose increase tensile index above 60%. In both cases, CNF cause a deterioration of drainage, but this effect is effectively counteracted by optimising the retention system.

Model-based performance and energy analyses of reverse osmosis to reuse wastewater in a PVC production site.

A pilot-scale reverse osmosis (RO) followed behind a membrane bioreactor (MBR) was developed for the desalination to reuse wastewater in a PVC production site. The solution-diffusion-film model (SDFM) based on the solution-diffusion model (SDM) and the film theory was proposed to describe rejections of electrolyte mixtures in the MBR effluent which consists of dominant ions (Na+ and Cl-) and several trace ions (Ca2+, Mg2+, K+ and SO42-). The universal global optimisation method was used to estimate the ion permeability coefficients (B) and mass transfer coefficients (K) in SDFM. Then, the membrane performance was evaluated based on the estimated parameters which demonstrated that the theoretical simulations were in line with the experimental results for the dominant ions. Moreover, an energy analysis model with the consideration of limitation imposed by the thermodynamic restriction was proposed to analyse the specific energy consumption of the pilot-scale RO system in various scenarios.

Pesticide effects on crabs: how environmental concentrations of endosulfan and chlorpyrifos affect embryos.

The objectives of this work were to evaluate the effects of environmentally relevant chlorpyrifos and endosulfan, concentrations in the incubation period, effective hatching and survival of embryos and neonates of the freshwater burrowing crab, Zilchiopsis collastinensis (Decapoda, Trichodactylidae). Both pesticides were prepared from commercial and technical grade products. The exposure to about 100, 200, and 400 ng endosulfan L(-1), and 48, 240, and 1,200 ng chlorpyrifos L(-1) did not cause differences in the incubation period or in effective hatching but decreased survival of neonates, especially in the concentrations prepared from the technical grade product. Even if these concentrations are below the median lethal concentration (LC50) values for embryos, these caused a significant decrease in the survival of neonates, i.e. when crabs are outside the egg and not protected by chorion. The decrease in the neonate population caused by these concentrations, which could be found in the environment, might impact aquatic communities.

Predator-prey imbalances due to a pesticide: density and applicability timing as determining factors for experimental assessments.

Predator-prey relationships are determining factors in sustaining community structure but xenobiotics, including pesticides, have the potential to alter them, causing imbalances at the ecosystem level. Although invertebrate predation on zooplankton is of high importance in shallow lakes, there is still little information regarding disturbances on this trophic interaction. This work assessed the potential effects of a chlorpyrifos-based pesticide (CLP) on the interaction between prawns Macrobrachium borellii and cladocerans Ceriodaphnia dubia, taking into account prey densities, specific time of exposure and contamination level. The analysis was focused on the specific sensitivity of both species and, especially, on the predation rate of M. borellii on C. dubia. The latter was evaluated through different treatments that combined predator and/or prey exposure to the insecticide, before (lapse of 12 h) or during the interaction. Under low prey density, when prawns were previously exposed to the insecticide, their consumption rate was lower than that of controls. Conversely, when cladocerans or both species were previously exposed, the prawns' feeding rate was higher. Under high prey density, there were no substantial differences among treatments. Comparatively, cladocerans were significantly more consumed when the exposure of both species was performed before rather than during the interaction. From the results obtained, it can be assumed that the trophic interaction under study is sensitive to CLP and that individual density and specific time of exposure are important variables to be considered in similar studies in order to obtain realistic results.

Enhancement of the production of TEMPO-mediated oxidation cellulose nanofibrils by kneading.

The industrial use of TEMPO-mediated oxidation (TMO) reaction to produce highly fibrillated cellulose nanofibrils has been hindered by high catalyst costs, long reaction times and high reaction volumes. The hypothesis that cellulose concentration during TMO process is key to increase the process of efficiency has been confirmed. The novelty of this research is the proof-of-concept for a significant enhancement of the TMO reaction by kneading the cellulose to work in concentrations above 120 g/L. Results show that the increase of the cellulose concentration in the TMO reaction, from the traditional 10 g/L to 120 g/L, increase not only the production for the same reaction volume (1200 %) but also the pulp recovery (up to 94 %). Moreover, the oxidation time can be reduced from 42 min to only 4 min while properties of both the oxidized pulps and the final nanocellulose are similar. On the other hand, the use of buffers in the TMO reaction allows us to keep the pH constant without using NaOH, and to improve the selectivity of the carboxyl groups production. The proposed process also minimizes the final environmental impact.

Global trends of pyrolysis research: a bibliometric analysis.

Pyrolysis has become an interesting waste valorization method leading to an increasing number of research studies in this field in the last decade. The present study aims to provide a comprehensive knowledge map of scientific production in pyrolysis, discuss the current state of research, and identify the main research hotspots and trends in recent years. The systematic review, supported by analysis of countries and institutions, keyword co-occurrence analysis, analysis of keyword trends, journal analysis, and article impact, was carried out on 6234 journal articles from the Science Citation Index Expanded database of the Web of Science Core Collection. As a result, four main research hotspots were identified: 1) characterization techniques and pyrolysis kinetic models, 2) biochar production and its main applications, 3) bio-oil production and catalytic pyrolysis, and 4) co-pyrolysis, which has become a consolidated research hotspot since 2018. Additionally, the main challenges and opportunities for future research have been identified, such as 1) the development of multi-step kinetic models for studying complex wastes, 2) the integration of biochar into other valorization processes, such as anaerobic digestion, and 3) the development of catalytic hydropyrolysis for the valorization of organic waste. This bibliometric analysis provides a visualization of the current context and future trends in pyrolysis, facilitating future collaborative research and knowledge exchange.

Preparation, Characterization and Industrial Application of Nanocellulose.

The international research community has made significant efforts in the production, characterization, and application of cellulose nanofibers (CNFs) in many sectors [...].

Recycling of TEMPO-mediated oxidation medium and its effect on nanocellulose properties.

The potential of TEMPO (2,2,6,6-tetramethyl-1-piperidinyloxy)-mediated oxidation (TMO) to produce cellulose nanofibrils (CNFs) is hindered using costly and environmentally harmful catalysts, limiting its large-scale implementation. To promote sustainability, the TMO medium should be reused but there is a lack of knowledge on this process. The novelty of this research is the identification of the key parameters that affect the recirculation of the TMO medium, and their impact on the quality of the oxidized pulps and CNF products. Contrary to previous hypothesis, results show that the accumulation of salts is not a key parameter; instead, the pulp consistency during oxidation plays a vital role since concentrations higher than 10 g/L led to better CNF quality. Thus, reusing 75 % of the reaction medium, when high pulp consistency is used, does not alter the CNF properties. By reusing the reaction medium up to six times, the catalyst dose is dramatically reduced by >90 % for TEMPO and 80 % for NaBr, compared to the conventional process (0.1 mmol of TEMPO/g and 1 mmol of NaBr/g without medium reuse). Additionally, the high consistency oxidation enables a reduction of >80 % in the reaction time and effluent, and thus a threefold increase in CNF production.

Ni(II) and Pb(II) Removal Using Bacterial Cellulose Membranes.

Bacterial cellulose (BC) is a highly crystalline nanosized material with a high number of active groups. This study focuses on the synthesis of BC membranes through fermentation, their characterization and application to remove Ni(II) and Pb(II) from wastewater by adsorption under different conditions. Four-day-grown BC membranes form three-dimensional nanofibril networks with a pH of 6.3 and a high cationic demand (52.5 µeq·g-1). The pseudo-second-order kinetic model and the Sips isotherm model best describe the adsorption of both metals. The intraparticle diffusion model of Ni(II) revealed a three-step mechanism of adsorption-plateau-adsorption, while Pb(II) adsorption followed a typical reducing-slope trend up to saturation. The highest removal of Ni(II) and Pb(II) was obtained at pH 4 with a BC dosage of 400 mg·L-1. The maximum adsorption capacities were 28.18 mg·g-1 and 8.49 mg·g-1 for Ni(II) and Pb(II), respectively, involving the total coverage of the material active sites. Thermodynamically, Ni(II) adsorption was exothermic, and Pb(II) was endothermic. The obtained values of sorption heat, activation and Gibbs' energy depicted a physisorption process. Ni(II) removal mechanism was ruled by crystallization on the metals adsorbed on the BC active groups, while Pb(II) was driven by the adsorption process, as shown by TEM images of the spent material.

Synergies between Fibrillated Nanocellulose and Hot-Pressing of Papers Obtained from High-Yield Pulp.

To extend the application of cost-effective high-yield pulps in packaging, strength and barrier properties are improved by advanced-strength additives or by hot-pressing. The aim of this study is to assess the synergic effects between the two approaches by using nanocellulose as a bulk additive, and by hot-pressing technology. Due to the synergic effect, dry strength increases by 118% while individual improvements are 31% by nanocellulose and 92% by hot-pressing. This effect is higher for mechanical fibrillated cellulose. After hot-pressing, all papers retain more than 22% of their dry strength. Hot-pressing greatly increases the paper's ability to withstand compressive forces applied in short periods of time by 84%, with a further 30% increase due to the synergic effect of the fibrillated nanocellulose. Hot-pressing and the fibrillated cellulose greatly decrease air permeability (80% and 68%, respectively) for refining pretreated samples, due to the increased fiber flexibility, which increase up to 90% using the combined effect. The tear index increases with the addition of nanocellulose, but this effect is lost after hot-pressing. In general, fibrillation degree has a small effect which means that low- cost nanocellulose could be used in hot-pressed papers, providing products with a good strength and barrier capacity.

Fit-for-Use Nanofibrillated Cellulose from Recovered Paper.

The cost-effective implementation of nanofibrillated cellulose (CNF) at industrial scale requires optimizing the quality of the nanofibers according to their final application. Therefore, a portfolio of CNFs with different qualities is necessary, as well as further knowledge about how to obtain each of the main qualities. This paper presents the influence of various production techniques on the morphological characteristics and properties of CNFs produced from a mixture of recycled fibers. Five different pretreatments have been investigated: a mechanical pretreatment (PFI refining), two enzymatic hydrolysis strategies, and TEMPO-mediated oxidation under two different NaClO concentrations. For each pretreatment, five high-pressure homogenization (HPH) conditions have been considered. Our results show that the pretreatment determines the yield and the potential of HPH to enhance fibrillation and, therefore, the final CNF properties. These results enable one to select the most effective production method with the highest yield of produced CNFs from recovered paper for the desired CNF quality in diverse applications.

Influence of dispersion of fibrillated cellulose on the reinforcement of coated papers.

The use of cellulose micro/nanofibrils (CMNFs) as reinforcement paper additive at industrial scale is delayed due to inconsistent results, suggesting a lack of proper consideration of some key parameters. The high influence of fibrillated nanocellulose dispersion has been recently identified as a key parameter for paper bulk reinforcement but it has not been studied for surface coating applications yet. This paper studies the effect of CMNF dispersion degree prior to their addition and during mixing with starch on the reinforcement of paper by coating. Results show that this effect depends on the type of CMNFs since it is related to the surface interactions. For a given formulation, a correlation is observed between the CMNF dispersion and the CMNF/starch mixing agitation with the rheology of the coating formulation which highly affects the paper properties. The optimal dispersion degree is different for each nanocellulose, but the best mechanical properties were always achieved at the lowest viscosity of the coating formulation. In general, the initial state of the nanocellulose 3D network, influences the mixing and smooth application of the coating and affects the reinforcement effect. Therefore, the CMNF industrial implementation in coating formulations will be facilitated by the on-line control of formulations prior to their surface application.

Bioaccumulation in freshwater crabs. Endosulfan accumulation in different tissues of Zilchiopsis collastinensis P. (Decapoda: Trichodactylidae).

We examined the bioaccumulation of α- and ß-endosulfan and endosulfan sulfate in tissues from the crab Zilchiopsis collastinensis. There was more endosulfan accumulated in the hepatopancreas (from <2 to 467.8 ng g(-1)) than in the gonads (from <2 to 52.1 ng g(-1)) or muscles (<2 ng g(-1)). The endosulfan concentrations in the hepatopancreas decreased over time and with the endosulfan dilution (p < 0.05). In the gonads there was little bioaccumulation, which did not vary over time (p > 0.05). The hepatopancreas is a dynamic organ that is able to depurate itself, whereas the gonads act as a sink for pesticides.

Gel Point as Measurement of Dispersion Degree of Nano-Cellulose Suspensions and Its Application in Papermaking.

The dispersion degree of cellulose micro and nanofibrils (CMFs/CNFs) in water suspensions is key to understand and optimize their effectiveness in several applications. In this study, we proposed a method, based on gel point (Øg), to calculate both aspect ratio and dispersion degree. This methodology was validated through the morphological characterization of CMFs/CNFs by Transmission Electronic Microscopy. The influence of dispersion degree on the reinforcement of recycled cardboard has also been evaluated by stirring CMF/CNF suspensions at different speeds. Results show that as stirring speed increases, Øg decreased to a minimum value, in which the aspect ratio is maximum. Then, Øg increased again. Suspensions with lower Øg, in the intermediate region of agitation present very good dispersion behavior with an open and spongy network structure, in which nanofibril clusters are totally dispersed. Higher stirring speeds shorten the nanofibrils and the networks collapse. Results show that the dispersion of the nanocellulose at the minimum Øg before their addition to the pulp, produces higher mechanical properties, even higher than when CNFs and pulp are agitated together. This method allows for the determination of the CMF/CNF dispersion, to maximize their behavior as strength agents. This knowledge would be crucial to understand why some industrial trials did not give satisfactory results.

Hexavalent Chromium Removal from Industrial Wastewater by Adsorption and Reduction onto Cationic Cellulose Nanocrystals.

Cationic cellulose nanocrystals (CCNC) are lignocellulosic bio-nanomaterials that present large, specific areas rich with active surface cationic groups. This study shows the adsorption removal of hexavalent chromium (Cr(VI)) from industrial wastewaters by the CCNC. The CCNC were synthetized through periodate oxidation and Girard's reagent-T cationization. The high value of CCNCs cationic groups and anionic demand reveal probable nanocrystal-Cr(VI) attraction. Adsorption was performed with synthetic Cr(VI) water at different pH, dosage, Cr(VI) concentration and temperature. Fast removal of Cr(VI) was found while operating at pH 3 and 100 mg·L-1 of dosage. Nevertheless, a first slower complete removal of chromium was achieved by a lower CCNC dosage (40 mg·L-1). Cr(VI) was fully converted by CCNC into less-toxic trivalent species, kept mainly attached to the material surface. The maximum adsorption capacity was 44 mg·g-1. Two mechanisms were found for low chromium concentrations (Pseudo-first and pseudo-second kinetic models and continuous growth multi-step intraparticle) and for high concentrations (Elovich model and sequential fast growth-plateau-slow growth intraparticle steps). The Sips model was the best-fitting isotherm. Isotherm thermodynamic analysis indicated a dominant physical sorption. The Arrhenius equation revealed an activation energy between physical and chemical adsorption. CCNC application at selected conditions in industrial wastewater achieved a legal discharge limit of 40 min.

Micro- and Nanofibrillated Cellulose from Annual Plant-Sourced Fibers: Comparison between Enzymatic Hydrolysis and Mechanical Refining.

The current trends in micro-/nanofibers offer a new and unmissable chance for the recovery of cellulose from non-woody crops. This work assesses a technically feasible approach for the production of micro- and nanofibrillated cellulose (MNFC) from jute, sisal and hemp, involving refining and enzymatic hydrolysis as pretreatments. Regarding the latter, only slight enhancements of nanofibrillation, transparency and specific surface area were recorded when increasing the dose of endoglucanases from 80 to 240 mg/kg. This supports the idea that highly ordered cellulose structures near the fiber wall are resistant to hydrolysis and hinder the diffusion of glucanases. Mechanical MNFC displayed the highest aspect ratio, up to 228 for hemp. Increasing the number of homogenization cycles increased the apparent viscosity in most cases, up to 0.14 Pa·s at 100 s-1 (1 wt.% consistency). A shear-thinning behavior, more marked for MNFC from jute and sisal, was evidenced in all cases. We conclude that, since both the raw material and the pretreatment play a major role, the unique characteristics of non-woody MNFC, either mechanical or enzymatically pretreated (low dose), make it worth considering for large-scale processes.

Critical comparison of the properties of cellulose nanofibers produced from softwood and hardwood through enzymatic, chemical and mechanical processes.

Current knowledge on the properties of different types of cellulose nanofibers (CNFs) is fragmented. Properties variation is very extensive, depending on raw materials, effectiveness of the treatments to extract the cellulose fraction from the lignocellulosic biomass, pretreatments to facilitate cellulose fibrillation and final mechanical process to separate the microfibrils. Literature offers multiple parameters to characterize the CNFs prepared by different routes. However, there is a lack of an extensive guide to compare the CNFs. In this study, we perform a critical comparison of rheological, compositional, and morphological features of CNFs, produced from the most representative types of woody plants, hardwood and softwood, using different types and intensities of pretreatments, including enzymatic, chemical and mechanical ones, and varying the severity of mechanical treatment focusing on the relationship between macroscopic and microscopic parameters. This structured information will be exceedingly useful to select the most appropriate CNF for a certain application based on the most relevant parameters in each case.

Modeling of Hexavalent Chromium Removal with Hydrophobically Modified Cellulose Nanofibers.

Cellulose nanofibers (CNF) are sustainable nanomaterials, obtained by the mechanical disintegration of cellulose, whose properties make them an interesting adsorbent material due to their high specific area and active groups. CNF are easily functionalized to optimize the performance for different uses. The hypothesis of this work is that hydrophobization can be used to improve their ability as adsorbents. Therefore, hydrophobic CNF was applied to adsorb hexavalent chromium from wastewater. CNF was synthetized by TEMPO-mediated oxidation, followed by mechanical disintegration. Hydrophobization was performed using methyl trimetoxysilane (MTMS) as a hydrophobic coating agent. The adsorption treatment of hexavalent chromium with hydrophobic CNF was optimized by studying the influence of contact time, MTMS dosage (0-3 mmol·g-1 CNF), initial pH of the wastewater (3-9), initial chromium concentration (0.10-50 mg·L-1), and adsorbent dosage (250-1000 mg CNF·L-1). Furthermore, the corresponding adsorption mechanism was identified. Complete adsorption of hexavalent chromium was achieved with CNF hydrophobized with 1.5 mmol MTMS·g-1 CNF with the faster adsorption kinetic, which proved the initial hypothesis that hydrophobic CNF improves the adsorption capacity of hydrophilic CNF. The optimal adsorption conditions were pH 3 and the adsorbent dosage was over 500 mg·L-1. The maximum removal was found for the initial concentrations of hexavalent chromium below 1 mg·L-1 and a maximum adsorption capacity of 70.38 mg·g-1 was achieved. The kinetic study revealed that pseudo-second order kinetics was the best fitting model at a low concentration while the intraparticle diffusion model fit better for higher concentrations, describing a multi-step mechanism of hexavalent chromium onto the adsorbent surface. The Freundlich isotherm was the best adjustment model.