Reduced interface effect of proton beam irradiation on the electrical properties of WSe2/hBN field effect transistors.

Two-dimensional transition metal dichalcogenide (TMDC) semiconductors are emerging as strong contenders for electronic devices that can be used in highly radioactive environments such as outer space where conventional silicon-based devices exhibit nonideal characteristics for such applications. To address the radiation-induced interface effects of TMDC-based electronic devices, we studied high-energy proton beam irradiation effects on the electrical properties of field-effect transistors (FETs) made with tungsten diselenide (WSe2) channels and hexagonal boron-nitride (hBN)/SiO2gate dielectrics. The electrical characteristics of WSe2FETs were measured before and after the irradiation at various proton beam doses of 1013, 1014, and 1015cm-2. In particular, we demonstrated the dependence of proton irradiation-induced effects on hBN layer thickness in WSe2FETs. We observed that the hBN layer reduces the WSe2/dielectric interface effect which would shift the transfer curve of the FET toward the positive direction of the gate voltage. Also, this interface effect was significantly suppressed when a thicker hBN layer was used. This phenomenon can be explained by the fact that the physical separation of the WSe2channel and SiO2dielectric by the hBN interlayer prevents the interface effects originating from the irradiation-induced positive trapped charges in SiO2reaching the interface. This work will help improve our understanding of the interface effect of high-energy irradiation on TMDC-based nanoelectronic devices.

Proton irradiation effects on mechanochemically synthesized and flash-evaporated hybrid organic-inorganic lead halide perovskites.

A hybrid organic-inorganic halide perovskite is a promising material for developing efficient solar cell devices, with potential applications in space science. In this study, we synthesized methylammonium lead iodide (MAPbI3) perovskites via two methods: mechanochemical synthesis and flash evaporation. We irradiated these perovskites with highly energetic 10 MeV proton-beam doses of 1011, 1012, 1013, and 4 × 1013protons cm-2and examined the proton irradiation effects on the physical properties of MAPbI3perovskites. The physical properties of the mechanochemically synthesized MAPbI3perovskites were not considerably affected after proton irradiation. However, the flash-evaporated MAPbI3perovskites showed a new peak in x-ray diffraction and an increased fluorescence lifetime in time-resolved photoluminescence under high-dose conditions, indicating considerable changes in their physical properties. This difference in behavior between MAPbI3perovskites synthesized via the abovementioned two methods may be attributed to differences in radiation hardness associated with the bonding strength of the constituents, particularly Pb-I bonds. Our study will help to understand the radiation effect of proton beams on organometallic halide perovskite materials.

Majority Voting-Based MAC Protocol for Exploiting Link-Layer Diversity in Wireless Networks.

In wireless local area networks (WLANs), the effect of interference signals between neighboring nodes increases as the number of wireless nodes using limited radio frequency resources in a limited space increases, which can significantly degrade the reliability of data transmission. In high-density WLANs, there can be several neighboring access points (APs) that can receive uplink transmission from a station. In conventional medium access control (MAC) protocols, uplink data frames containing errors or transmitted from a non-associated station are discarded at APs. Alternatively, we propose a MAC protocol using redundant wireless links between neighboring APs and the non-associated stations. In the proposed MAC protocol, we consider a centralized WLAN with a control node that performs error corrections of erroneous uplink data frames via a majority voting algorithm-based link-layer diversity scheme using uplink data received from multiple APs to increase the reliability of data transmission. In addition, we propose an adaptive carrier sensing ranging mechanism to improve the uplink network throughput in the proposed centralized WLAN system. Further, we conduct simulation studies and software-defined radio-based experiments to evaluate the performance of the proposed MAC protocol in various WLAN scenarios.

Design optimization of a 6.4†mm-diameter electromagnetic 2D scanning micromirror.

We present the design optimization, fabrication, and analysis of an electromagnetic biaxial scanning micromirror with 6.4 mm-diameter. The scanner is composed of a micromirror supported by two concentric gimbal structures with unique single turn coil. A cylindrical permanent magnet assembly is placed under the micromirror to provide a radial magnetic field for actuation. Lumped element model parameters and magnetic circuit have been optimized to maximize the driving torque. Fabricated micromirror has been actuated at 300 Hz and 1,010 Hz and maximum optical scan angle of 25.6° and 35.3° have been obtained for the vertical and horizontal scans, respectively. Crosstalk during the actuation has been analyzed, and improved models have been proposed to reduce the crosstalk.

A Low Frequency Vibration Energy Harvester Using ZnO Nanowires on Elastic Interdigitated Electrodes.

This paper presents a low frequency piezoelectric vibration energy harvester using ZnO nanowires on elastic interdigitated electrodes. The interdigitated electrodes are formed using electroplated Ni and have suspended parts at the edges that are elastic and deformable by applying external force. A spherical Ni ball is used as a proof mass, which transforms a low frequency mechanical vibration into the force applied to deform the elastic electrodes. The ZnO nanowires are grown selectively on the electrodes and can generate a piezoelectric potential when the elastic electrodes are deformed by the proof mass activated by the external mechanical vibration. The proposed operation concept is demonstrated using two different types of energy harvesters, which have simple suspended part and cantilever array structures added to the electrodes, respectively. The output voltage of the fabricated harvesters is measured using a vibration exciter at 6 Hz sinusoidal vibration with an acceleration of 0.5 g. Maximum output power of 12.8 pW and 18.8 pW was generated with a load resistance of 1 MΩ for the harvesters using the simple suspended structure and cantilever array, respectively.

Fabrication of Localized Surface Plasmon Resonance Sensor Based on Optical Fiber and Micro Fluidic Channel.

This paper proposes Fiber-Optic Localized Surface Plasmon Resonance (FO LSPR) sensor combined with a micro fluidic channel, which enables continuous supply of fluid for bio-reaction. The proposed method prevents degradation of the sensing performance due to changes in measurement conditions. The feasibility of the FO LSPR sensor with a micro fluidic channel was demonstrated by computational fluid dynamics (CFD) simulation. Also, the proposed method was assessed by measuring the output intensity of the FO LSPR sensor at various refractive index solutions. Finally, a prostate-specific antigen (PSA) immunoassay was performed to evaluate the possibility of the fabricated sensor system as a biosensor.

Novel microbial photobioelectrochemical cell using an invasive ultramicroelectrode array and a microfluidic chamber.

OBJECTIVE: To fabricate a novel microbial photobioelectrochemical cell using silicon microfabrication techniques. RESULTS: High-density photosynthetic cells were immobilized in a microfluidic chamber, and ultra-microelectrodes in a microtip array were inserted into the cytosolic space of the cells to directly harvest photosynthetic electrons. In this way, the microbial photobioelectrochemical cell operated without the aid of electron mediators. Both short circuit current and open circuit voltage of the microbial photobioelectrochemical cell responded to light stimuli, and recorded as high as 250 pA and 45 mV, respectively. CONCLUSION: A microbial photobioelectrochemical cell was fabricated with potential use in next-generation photosynthesis-based solar cells and sensors.

Mixl1 and Flk1 Are Key Players of Wnt/TGF-ß Signaling During DMSO-Induced Mesodermal Specification in P19 cells.

Dimethyl sulfoxide (DMSO) is widely used to induce multilineage differentiation of embryonic and adult progenitor cells. To date, little is known about the mechanisms underlying DMSO-induced mesodermal specification. In this study, we investigated the signaling pathways and lineage-determining genes involved in DMSO-induced mesodermal specification in P19 cells. Wnt/ß-catenin and TGF-ß superfamily signaling pathways such as BMP, TGF-ß and GDF1 signaling were significantly activated during DMSO-induced mesodermal specification. In contrast, Nodal/Cripto signaling pathway molecules, required for endoderm specification, were severely downregulated. DMSO significantly upregulated the expression of cardiac mesoderm markers but inhibited the expression of endodermal and hematopoietic lineage markers. Among the DMSO-activated cell lineage markers, the expression of Mixl1 and Flk1 was dramatically upregulated at both the transcript and protein levels, and the populations of Mixl1+, Flk1+ and Mixl1+/Flk1+ cells also increased significantly. DMSO modulated cell cycle molecules and induced cell apoptosis, resulting in significant cell death during EB formation of P19 cells. An inhibitor of Flk1, SU5416 significantly blocked expressions of TGF-ß superfamily members, mesodermal cell lineage markers and cell cycle molecules but it did not affect Wnt molecules. These results demonstrate that Mixl1 and Flk1 play roles as key downstream or interacting effectors of Wnt/TGF-ß signaling pathway during DMSO-induced mesodermal specification in P19 cells.

Electromagnetic biaxial microscanner with mechanical amplification at resonance.

We present the design, fabrication, and measurement results of an electromagnetic biaxial microscanner with mechanical amplification mechanism. A gimbaled scanner with two distinct single-crystal silicon layer thicknesses and integrated copper coils has been fabricated with combination of surface and bulk micromachining processes. A magnet assembly consisting of an array of permanent magnets and a pole piece has been placed under the substrate to provide high strength lateral magnetic field oriented 45° to two perpendicular scanning axes. Micromirror has been supported by additional gimbal to implement a mechanical amplification. A 1.2mm-diameter mirror with aluminum reflective surface has been actuated at 60Hz for vertical scan and at 21kHz for horizontal scan. Maximum scan angle of 36.12° at 21.19kHz and 17.62° at 60Hz have been obtained for horizontal and vertical scans, respectively.

Acute changes of left ventricular hemodynamics and function during percutaneous coronary intervention in patients with unprotected left main coronary artery disease.

Percutaneous coronary interventions (PCIs) are increasingly being used to treat unprotected left main coronary artery (ULMCA) lesions. However, research is sparse on the acute changes of left ventricular (LV) hemodynamics and function during PCI in patients with ULMCA stenosis. We aimed to assess the acute changes of LV function using speckle-tracking imaging during PCI in these patients. Fifteen consecutive patients who underwent elective PCI for ULMCA stenosis were enrolled. Echocardiographic studies and pressure measurement were performed at baseline, during PCI and after PCI. LMCA occlusion with a first balloon inflation induced a marked reduction in the peak positive derivative of LV pressure (dP/dt max), LV global longitudinal strain (GLS), and systolic and diastolic strain rates, and a marked increase in LV end-diastolic pressure (EDP) (all P < 0.01). During the second inflation, the degrees of LV hemodynamic and functional changes were similar to those of the first inflation, even with a higher inflation pressure. During the third inflation, the values of GLS and dP/dt max were higher than those of the second inflation (P = 0.03 and P = 0.05, respectively). After optimal PCI, dP/dt max, LVEDP, and strain parameters were improved to baseline values. LV hemodynamics and function were considerably impaired with the first ballooning during PCI for ULMCA stenosis. However, the degrees of LV hemodynamic and functional changes decreased with each successive balloon inflation, which can be explained by ischemic preconditioning. After all procedures were safely completed, LV systolic function was improved without LV diastolic stunning.

Quantitative Understanding of Ionic Channel Network Variation in Nafion with Hydration Using Current Sensing Atomic Force Microscopy.

Proton exchange membranes are an essential component of proton-exchange membrane fuel cells (PEMFC). Their performance is directly related to the development of ionic channel networks through hydration. Current sensing atomic force microscopy (CSAFM) can map the local conductance and morphology of a sample surface with sub-nano resolution simultaneously by applying a bias voltage between the conducting tip and sample holder. In this study, the ionic channel network variation of Nafion by hydration has been quantitatively characterized based on the basic principles of electrodynamics and CSAFM. A nano-sized PEMFC has been created using a Pt-coated tip of CSAFM and one side Pt-coated Nafion, and studied under different relative humidity (RH) conditions. The results have been systematically analyzed. First, the morphology of PEMFC under each RH has been studied using line profile and surface roughness. Second, the CSAFM image has been analyzed statistically through the peak value and full-width half-maximum of the histograms. Third, the number of protons moving through the ionic channel network (NPMI) has been derived and used to understand ionic channel network variation by hydration. This study develops a quantitative method to comprehend variations in the ionic channel network by calculating the movement of protons into the ionic channel network based on CSAFM images. To verify the method, a comparison is made between the NPMI and the changes in proton conductivity under different RH conditions and it reveals a good agreement. This developed method can offer a quantitative approach for characterizing the morphological structure of PEM. Also, it can provide a quantitative tool for interpretating CSAFM images.

Vitamin C-induced CO2 capture enables high-rate ethylene production in CO2 electroreduction.

High-rate production of multicarbon chemicals via the electrochemical CO2 reduction can be achieved by efficient CO2 mass transport. A key challenge for C-C coupling in high-current-density CO2 reduction is how to promote *CO formation and dimerization. Here, we report molecularly enhanced CO2-to-*CO conversion and *CO dimerization for high-rate ethylene production. Nanoconfinement of ascorbic acid by graphene quantum dots enables immobilization and redox reversibility of ascorbic acid in heterogeneous electrocatalysts. Cu nanowire with ascorbic acid nanoconfined by graphene quantum dots (cAA-CuNW) demonstrates high-rate ethylene production with a Faradaic efficiency of 60.7% and a partial current density of 539 mA/cm2, a 2.9-fold improvement over that of pristine CuNW. Furthermore, under low CO2 ratio of 33%, cAA-CuNW still exhibits efficient ethylene production with a Faradaic efficiency of 41.8%. We find that cAA-CuNW increases *CO coverage and optimizes the *CO binding mode ensemble between atop and bridge for efficient C-C coupling. A mechanistic study reveals that ascorbic acid can facilitate *CO formation and dimerization by favorable electron and proton transfer with strong hydrogen bonding.

The North Equatorial Current and rapid intensification of super typhoons.

Super Typhoon Mangkhut, which traversed the North Equatorial Current (NEC; 8-17 °N) in the western North Pacific in 2018, was the most intense Category-5 tropical cyclone (TC) with the longest duration in history-3.5 days. Here we show that the combination of two factors-high ocean heat content (OHC) and increased stratification - makes the NEC region the most favored area for a rapid intensification (RI) of super typhoons, instead of the Eddy Rich Zone (17-25 °N), which was considered the most relevant for RI occurrence. The high OHC results from a northward deepening thermocline in geostrophic balance with the westward-flowing NEC. The stratification is derived from precipitation associated with the Inter-Tropical Convergence Zone in the summer peak typhoon season. These factors, which are increasingly significant over the past four decades, impede the TC-induced sea surface cooling, thus enhancing RI of TCs and simultaneously maintaining super typhoons over the NEC region.

Quantitative Study of Charge Distribution Variations on Silica-Nafion Composite Membranes under Hydration Using an Approximation Model.

Understanding the ionic structure and charge transport on proton exchange membranes (PEMs) is crucial for their characterization and development. Electrostatic force microscopy (EFM) is one of the best tools for studying the ionic structure and charge transport on PEMs. In using EFM to study PEMs, an analytical approximation model is required for the interoperation of the EFM signal. In this study, we quantitatively analyzed recast Nafion and silica-Nafion composite membranes using the derived mathematical approximation model. The study was conducted in several steps. In the first step, the mathematical approximation model was derived using the principles of electromagnetism and EFM and the chemical structure of PEM. In the second step, the phase map and charge distribution map on the PEM were simultaneously derived using atomic force microscopy. In the final step, the charge distribution maps of the membranes were characterized using the model. There are several remarkable results in this study. First, the model was accurately derived as two independent terms. Each term shows the electrostatic force due to the induced charge of the dielectric surface and the free charge on the surface. Second, the local dielectric property and surface charge are numerically calculated on the membranes, and the calculation results are approximately valid compared with those in other studies.

Low-Temperature Cross-Linkable Hole Transport Materials for Solution-Processed Quantum Dot and Organic Light-Emitting Diodes with High Efficiency and Color Purity.

Cross-linkable hole transport materials (HTMs) are ideal for improving the performance of solution-processed quantum dot light-emitting diodes (QLEDs) and phosphorescent light-emitting diodes (OLEDs). However, previously developed cross-linkable HTMs possessed poor hole transport properties, high cross-linking temperatures, and long curing times. To achieve efficient cross-linkable HTMs with high mobility, low cross-linking temperature, and short curing time, we designed and synthesized a series of low-temperature cross-linkable HTMs comprising dibenzofuran (DBF) and 4-divinyltriphenylamine (TPA) segments for highly efficient solution-processed QLEDs and OLEDs. The introduction of divinyl-functionalized TPA in various positions of the DBF core remarkably affected their chemical, physical, and electrochemical properties. In particular, cross-linked 4-(dibenzo[b,d]furan-3-yl)-N,N-bis(4-vinylphenyl)aniline (3-CDTPA) exhibited a deep highest occupied molecular orbital energy level (5.50 eV), high hole mobility (2.44 × 10-4 cm2 V-1 s-1), low cross-linking temperature (150 °C), and short curing time (30 min). Furthermore, a green QLED with 3-CDTPA as the hole transport layer (HTL) exhibited a notable maximum external quantum efficiency (EQEmax) of 18.59% with a remarkable maximum current efficiency (CEmax) of 78.48 cd A-1. In addition, solution-processed green OLEDs with 3-CDTPA showed excellent device performance with an EQEmax of 15.61%, a CEmax of 52.51 cd A-1, and outstanding CIE(x, y) color coordinates of (0.29, 0.61). This is one of the highest reported EQEs and CEs with high color purity for green solution-processed QLEDs and OLEDs using a divinyl-functionalized cross-linked HTM as the HTL. We believe that this study provides a new strategy for designing and synthesizing practical cross-linakable HTMs with enhanced performance for highly efficient solution-processed QLEDs and OLEDs.

Analysis of fiber-optic localized surface plasmon resonance sensor by controlling formation of gold nanoparticles and its bio-application.

Localized surface plasmon resonance (LSPR) occurs when nanoparticles are bound to the surface of a sensor which is sensitive to the refractive index of the surrounding medium. The sensitivity of the sensor is highly dependent on the type of nanoparticles and their size, density and shape. Using an optical fiber as a sensor has various advantages, such as guided signal delivery and low energy loss. In this study, a Fiber-optic localized surface plasmon resonance (FO-LSPR) sensor was developed and the sizes of the gold nanoparticles (Au NPs) used therein were controlled by reduction with chloroauric acid. The extinction cross-section was calculated by the Mie theory to examine the dependence of the resonance intensity and sensitivity of the fabricated FO-LSPR sensor on the size and density of the Au NPs situated on its end-face. In order to use it as a biosensor, the fabricated FO-LSPR sensor was used to detect the biotin-streptavidin interaction.

Analysis of Ionic Domain Evolution on a Nafion-Sulfonated Silica Composite Membrane Using a Numerical Approximation Model Based on Electrostatic Force Microscopy.

It is important to characterize the proton transport mechanisms of proton exchange membranes (PEMs). Electrostatic force microscopy (EFM) is used to characterize the ionic structures of membranes. In this study, we attempted to quantitatively analyze the proton conductivity enhancement of Nafion-sulfonated silica (SSA) composite membranes with variations in the ionic channel distribution. This study involved several steps. The morphology and surface charge distribution of both membranes were measured using EFM. The measured data were analyzed using a numerical approximation model (NAM) that was capable of providing the magnitude and classification of the surface charges. There were several findings of ionic channel distribution variations in Nafion-SSA. First, the mean local ionic channel density of Nafion-SSA was twice as large as that of the pristine Nafion. The local ionic channel density was non-uniform and the distribution of the ionic channel density of Nafion-SSA was 23.5 times larger than that of pristine Nafion. Second, local agglomerations due to SSA were presumed by using the NAM, appearing in approximately 10% of the scanned area. These findings are meaningful in characterizing the proton conductivity of PEMs and imply that the NAM is a suitable tool for the quantitative assessment of PEMs.

High-performance biosensor using a sandwich assay via antibody-conjugated gold nanoparticles and fiber-optic localized surface plasmon resonance.

For real-time and high-sensitivity analysis of low-concentration targets, a sandwich immunoassay using second antibody-second gold nanoparticle (2nd Ab-2nd AuNP) conjugates was combined with fiber-optic localized surface plasmon resonance (FO LSPR). An FO LSPR format was constructed by immobilizing AuNPs on a fiber-optic cross-section for compactness, portability, and ease of handling. In addition, it was combined with a microfluidic system to ensure reproducibility and reliability of measurements. A detection limit of 97.6 fg/mL (148 aM) was obtained for thyroglobulin (Tg) without a sandwich assay. The detection limit was enhanced by approximately 15 times (6.6 fg/mL, 10 aM) when a sandwich strategy was performed with a 2nd Ab-2nd AuNP signal amplifier to further improve the responsivity. Additionally, the good selectivity of the proposed method was confirmed against the unpaired antigen. To evaluate its practical applicability in the field, an FO LSPR biosensor boosted with a sandwich assay using antibody-functionalized AuNPs was applied to detect Tg contained in patient serum, and the results were compared and verified with those of a commercial radioimmunoassay kit. Based on the above results, the signal-enhancing immunoassay with FO LSPR will contribute to the development of optical biosensors for early diagnosis and preventive applications.

Fiber Optic Plasmonic Sensors Based on Nanodome Arrays with Nanogaps.

In this study, a high-performance fiber optic surface plasmon resonance (FO-SPR) sensor using a dome array with nanogaps (DANG) is proposed for label-free real-time detection of biomolecules. A novel and simple method using polymer beads enables high sensitivity by allowing hotspots with nanometer spacing between the Au dome and the surrounding film. The nanodome structure, which comprises a polymer core and a Au shell, induces a localized surface plasmon, expands the sensing area, and extensively enhances the electromagnetic field. The refractive index sensitivity of the FO-SPR sensor with nanostructures, i.e., with nanogaps and nanodomes, was found to be 7.8 times higher than that of the FO-SPR sensor without nanostructures. The proposed sensor achieved a low detection limit of 38 fg/mL while quantifying thyroglobulin antibody-antigen interactions and exhibited excellent selectivity. In addition, it helped detect serum samples with a 103% recovery rate.

High-Quality Microprintable and Stretchable Conductors for High-Performance 5G Wireless Communication.

With the advent of 5G wireless and Internet of Things technologies, flexible and stretchable printed circuit boards (PCBs) should be designed to address all the specifications necessary to receive signal transmissions, maintaining the signal integrity, and providing electrical connections. Here, we propose a silver nanoparticle (AgNP)/silver nanowire (AgNW) hybrid conductor and high-quality microprinting technology for fabricating flexible and stretchable PCBs in high-performance 5G wireless communication. A simple and low-cost reverse offset printing technique using a commercial adhesive hand-roller was adapted to ensure high-resolution and excellent pattern quality. The AgNP/AgNW micropatterns were fabricated in various line widths, from 5 µm to 5 mm. They exhibited excellent pattern qualities, such as fine line spacing, clear edge definition and outstanding pattern uniformity. After annealing via intense pulsed light irradiation, they showed outstanding electrical resistivity (15.7 µΩ cm). Moreover, they could withstand stretching up to a strain of 90% with a small change in resistance. As a demonstration of their practical application, the AgNP/AgNW micropatterns were used to fabricate 5G communication antennas that exhibited excellent wireless signal processing at operating frequencies in the C-band (4-8 GHz). Finally, a wearable sensor fabricated with these AgNP/AgNW micropatterns could successfully detected fine finger movements in real time with excellent sensitivity.