Combined Antimicrobial Effect of Bio-Waste Olive Leaf Extract and Remote Cold Atmospheric Plasma Effluent.

A novel strategy involving Olive Leaf Extract (OLE) and Cold Atmospheric Plasma (CAP) was developed as a green antimicrobial treatment. Specifically, we reported a preliminary investigation on the combined use of OLE + CAP against three pathogens, chosen to represent medical and food industries (i.e., E. coli, S. aureus and L. innocua). The results indicated that a concentration of 100 mg/mL (total polyphenols) in OLE can exert an antimicrobial activity, but still insufficient for a total bacterial inactivation. By using plain OLE, we significantly reduced the growth of Gram positive S. aureus and L. innocua, but not Gram-negative E. coli. Instead, we demonstrated a remarkable decontamination effect of OLE + CAP in E. coli, S. aureus and L. innocua samples after 6 h. This effect was optimally maintained up to 24 h in S. aureus strain. E. coli and L. innocua grew again in 24 h. In the latter strain, OLE alone was most effective to significantly reduce bacterial growth. By further adjusting the parameters of OLE + CAP technology, e.g., OLE amount and CAP exposure, it could be possible to prolong the initial powerful decontamination over a longer time. Since OLE derives from a bio-waste and CAP is a non-thermal technology based on ionized air, we propose OLE + CAP as a potential green platform for bacterial decontamination. As a combination, OLE and CAP can lead to better antimicrobial activity than individually and may replace or complement conventional thermal procedures in food and biomedical industries.

Evaluation of Mussel Shells Powder as Reinforcement for PLA-Based Biocomposites.

The use of biopolyesters, as polymeric matrices, and natural fillers derived from wastes or by-products of food production to achieve biocomposites is nowadays a reality. The present paper aims to valorize mussel shells, 95% made of calcium carbonate (CaCO3), converting them into high-value added products. The objective of this work was to verify if CaCO3, obtained from Mediterranean Sea mussel shells, can be used as filler for a compostable matrix made of Polylactic acid (PLA) and Poly(butylene adipate-co-terephthalate) (PBAT). Thermal, mechanical, morphological and physical properties of these biocomposites were evaluated, and the micromechanical mechanism controlling stiffness and strength was investigated by analytical predictive models. The performances of these biocomposites were comparable with those of biocomposites produced with standard calcium carbonate. Thus, the present study has proved that the utilization of a waste, such as mussel shell, can become a resource for biocomposites production, and can be an effective option for further industrial scale-up.

Processability and Degradability of PHA-Based Composites in Terrestrial Environments.

In this work, composites based on poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHB-HV) and waste wood sawdust (SD) fibers, a byproduct of the wood industry, were produced by melt extrusion and characterized in terms of processability, thermal stability, morphology, and mechanical properties in order to discriminate the formulations suitable for injection molding. Given their application in agriculture and/or plant nursery, the biodegradability of the optimized composites was investigated under controlled composting conditions in accordance with standard methods (ASTM D5338-98 and ISO 20200-2004). The optimized PHB-HV/SD composites were used for the production of pots by injection molding and their performance was qualitatively monitored in a plant nursery and underground for 14 months. This study presents a sustainable option of valuation of wood factory residues and lowering the production cost of PHB-HV-based compounds without affecting their mechanical properties, improving their impact resistance and biodegradability rates in terrestrial environments.

Use of bio-containers from seagrass wrack with nursery planting to improve the eco-sustainability of coastal habitat restoration.

Traditional revegetation techniques employed to restore seagrass meadows and coastal dunes have recently been criticized for their impact on donor populations as well as for the installation of plant anchoring structures made of non-biodegradable or not natural materials in recipient habitats. To improve the ecological sustainability of restoration practices, a novel plantable biodegradable container made of beach-cast seagrass wrack and a bio-based polymer was produced. The long-term performance of two seagrasses, Cymodocea nodosa and Zostera noltei, and two dune plants, Euphorbia paralias and Thinopyrum junceum, grown in nurseries from seeds using the bio-container or a non-biodegradable container of equal size/form made of a conventional plastic (control) was also examined. In addition, the development of bio-container-raised C. nodosa plants in the field was compared to that of plants removed from control containers at the installation and anchored with a traditional system. The bio-container degraded slowly in seawater and in sand and lost its functionality after about three years. In nurseries, all the tested species grown in bio-containers performed as well as, or better than, those raised in non-biodegradable ones. Six months after transplanting into the field, 80% of the C. nodosa nursery-raised plants installed with their bio-container have colonized the surrounding substrate while most of those planted with the traditional system was lost. These results indicate that the new bio-container may support plant growth, and it may also provide protection and anchorage to plants in the field. The use of this bio-container in combination with nursery techniques could improve the environmental sustainability of coastal restoration interventions by providing large plant stocks from seed, thus reducing the impact of collection on donor populations. This approach would also limit the introduction of extraneous materials in recipient habitats and offer an opportunity for valorizing seagrass beach-cast material.

3D Printed Piezoelectric BaTiO3/Polyhydroxybutyrate Nanocomposite Scaffolds for Bone Tissue Engineering.

Bone defects are a significant health problem worldwide. Novel treatment approaches in the tissue engineering field rely on the use of biomaterial scaffolds to stimulate and guide the regeneration of damaged tissue that cannot repair or regrow spontaneously. This work aimed at developing and characterizing new piezoelectric scaffolds to provide electric bio-signals naturally present in bone and vascular tissues. Mixing and extrusion were used to obtain nanocomposites made of polyhydroxybutyrate (PHB) as a matrix and barium titanate (BaTiO3) nanoparticles as a filler, at BaTiO3/PHB compositions of 5/95, 10/90, 15/85 and 20/80 (w/w%). The morphological, thermal, mechanical and piezoelectric properties of the nanocomposites were studied. Scanning electron microscopy analysis showed good nanoparticle dispersion within the polymer matrix. Considerable increases in the Young's modulus, compressive strength and the piezoelectric coefficient d31 were observed with increasing BaTiO3 content, with d31 = 37 pm/V in 20/80 (w/w%) BaTiO3/PHB. 3D printing was used to produce porous cubic-shaped scaffolds using a 90° lay-down pattern, with pore size ranging in 0.60-0.77 mm and good mechanical stability. Biodegradation tests conducted for 8 weeks in saline solution at 37 °C showed low mass loss (∼4%) for 3D printed scaffolds. The results obtained in terms of piezoelectric, mechanical and chemical properties of the nanocomposite provide a new promising strategy for vascularized bone tissue engineering.

Marine copepod culture as a potential source of bioplastic-degrading microbiome: The case of poly(butylene succinate-co-adipate).

The poly(butylene succinate-co-adipate) (PBSA) is emerging as environmentally sustainable polyester for applications in marine environment. In this work the capacity of microbiome associated with marine plankton culture to degrade PBSA, was tested. A taxonomic and functional characterization of the microbiome associated with the copepod Acartia tonsa, reared in controlled conditions, was analysed by 16S rDNA metabarcoding, in newly-formed adult stages and after 7 d of incubation. A predictive functional metagenomic profile was inferred for hydrolytic activities involved in bioplastic degradation with a particular focus on PBSA. The copepod-microbiome was also characterized in newly-formed carcasses of A. tonsa, and after 7 and 33 d of incubation in the plankton culture medium. Copepod-microbiome showed hydrolytic activities at all developmental stages of the alive copepods and their carcasses, however, the evenness of the hydrolytic bacterial community significantly increased with the time of incubation in carcasses. Microbial genera, never described in association with copepods: Devosia, Kordia, Lentibacter, Methylotenera, Rheinheimera, Marinagarivorans, Paraglaciecola, Pseudophaeobacter, Gaiella, Streptomyces and Kribbella sps., were retrieved. Kribbella sp. showed carboxylesterase activity and Streptomyces sp. showed carboxylesterase, triacylglycerol lipase and cutinase activities, that might be involved in PBSA degradation. A culturomic approach, adopted to isolate bacterial specimen from carcasses, led to the isolation of the bacterial strain, Vibrio sp. 01 tested for the capacity to promote the hydrolysis of the ester bonds. Granules of PBSA, incubated 82 d at 20 °C with Vibrio sp. 01, were characterized by scanning electron microscopy, infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry, showing fractures compared to the control sample, and hydrolysis of ester bonds. These preliminary results are encouraging for further investigation on the ability of the microbiome associated with plankton to biodegrade polyesters, such as PBSA, and increasing knowledge on microorganisms involved in bioplastic degradation in marine environment.

Seawater Biodegradable Poly(butylene succinate-co-adipate)-Wheat Bran Biocomposites.

The present work focused on the development and characterization of biocomposites based on a fully bio-based polyester, poly(butylene succinate-co-butylene adipate) (PBSA), and wheat bran derived by flour milling. PBSA-bran composites containing 5, 10, 15, and 20 wt.% of wheat bran were produced via melt extrusion and processed by injection molding. Their thermal, rheological, morphological, and tensile properties were investigated. In addition, a biodegradation test in a natural marine environment was conducted on composite dog-bones to assess the capacity of the used filler to increase the PBSA biodegradation rate. The composites maintained similar melt processability and mechanical properties to virgin PBSA with up to 15 wt.% bran content. This result was also supported by morphological investigation, which showed good filler dispersion within the polymer matrix at low-mid bran content, whereas poor polymer-filler dispersion occurred at higher concentrations. Furthermore, the biodegradation tests showed bran's capacity to improve the PBSA biodegradation rate, probably due to the hygroscopic bran swelling, which induced the fragmentation of the dog-bone with a consequent increase in the polymeric matrix-seawater interfacial area, accelerating the degradation mechanisms. These results encourage the use of wheat bran, an abundant and low-cost agri-food by-product, as a filler in PBSA-based composites to develop products with good processability, mechanical properties, and controlled biodegradability in marine environments.

Direct Recycling of WC-Co Grinding Chip.

Grinding is a finishing process for high precision, high surface quality parts, and hard materials, including tool fabrication and sharpening. The recycling of grinding scraps, which often contain rare and costly materials such as tungsten carbide (WC-Co), has been established for decades. However, there is a growing need for more energy-efficient and environmentally friendly recycling processes. Currently, grinding sludges, which are a mixture of abrasives, lubricants, and hard metal chips, are only treated through chemical recycling. Direct recycling ("reuse" of chips as raw material) is the most effective but not yet viable process due to the presence of contaminants. This paper presents an oil-free dry grinding process that produces high-quality chips (i.e., oil-free and with few contaminants, smaller than 60 mesh particle size) that can be directly recycled, as opposed to the oil-based wet grinding that generates sludges, which require indirect recycling. The proposed alternative recycling method is validated experimentally using WC-Co chips from a leading hard metals' processing specialized company. The contaminant level (oxygen 0.8 wt.%, others < 0.4 wt.%), granulometry (chip D50 = 10.4 µm with grain size < 3 µm) and morphology of the recycled chips' powder is comparable to commercial powders proving the research and industrial potential of direct recycling. The comparison of sintered products using recycled and commercial powder provided equivalent characteristics for hardness (HRA of 90.7, HV30 of 1430), porosity grade (A02-04) and grain size (<3 µm).

Wood Residue-Derived Biochar as a Low-Cost, Lubricating Filler in Poly(butylene succinate-co-adipate) Biocomposites.

This study focused on the development of a novel biocomposite material formed by a thermoplastic biodegradable polyester, poly(butylene succinate-co-adipate) (PBSA), and a carbonaceous filler as biochar (BC) derived by the pyrolysis of woody biomass waste. Composites with various BC contents (5, 10, 15, and 20 wt.%) were obtained by melt extrusion and investigated in terms of their processability, thermal, rheological, and mechanical properties. In all the composites, BC lowered melt viscosity, behaving as a lubricant, and enhancing composite extrudability and injection moulding at high temperatures up to 20 wt.% of biochar. While the use of biochar did not significantly change composite thermal stability, it increased its stiffness (Young modulus). Differential scanning calorimeter (DSC) revealed the presence of a second crystal phase induced by the filler addition. Furthermore, results suggest that biochar may form a particle network that hinders polymer chain disentanglement, reducing polymer flexibility. A biochar content of 10 wt.% was selected as the best trade-off concentration to improve the composite processability and cost competitiveness without compromising excessively the tensile properties. The findings support the use of biochar as a sustainable renewable filler and pigment for PBSA. Biochar is a suitable candidate to replace more traditional carbon black pigments for the production of biodegradable and inexpensive innovative PBSA composites with potential fertilizing properties to be used in agricultural applications.

From Waste Vegetable Oil to a Green Compatibilizer for HDPE/PA6 Blends.

When properly compatibilized, the blending of polyethylene (PE) and polyamide (PA) leads to materials that combine low prices, suitable processability, impact resistance, and attractive mechanical properties. Moreover, the possibility of using these polymers without prior separation may be a suitable opportunity for their recycling. In this work, the use of an epoxidized waste vegetable oil (EWVO) was investigated as a green compatibilizer precursor (CP) for the reactive blending of a high-density PE (HDPE) with a polyamide-6 (PA6). EWVO was synthesized from waste vegetable cooking oil (WVO) using ion-exchange resin (Amberlite) as a heterogeneous catalyst. HDPE/PA6 blends were produced with different weight ratios (25/75, 75/25, 85/15) and amounts of EWVO (1, 2, 5 phr). Samples with WVO or a commercial fossil-based CP were also prepared for comparison. All the blends were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), rheology, and mechanical tests. In the case of HDPE/PA6 75/25 and 85/15 blends, the addition of EWVO at 2 phr showed a satisfactory compatibilizing effect, thus yielding a material with improved mechanical properties with respect to the blend without compatibilizer. On the contrary, the HDPE/PA6 25/75 ratio yielded a material with a high degree of crosslinking that could not be further processed or characterized. In conclusion, the results showed that EWVO had a suitable compatibilizing effect in HDPE/PA6 blends with high HDPE content, while it resulted in unsuitable for blends with high content of PA6.

Bioethanol-gasoline fuel blends: exhaust emissions and morphological characterization of particulate from a moped engine.

This study was aimed at evaluating the effects of gasoline-ethanol blends on the exhaust emissions in a catalyst-equipped four-stroke moped engine. The ethanol was blended with unleaded gasoline in at percentages (10, 15, and 20% v/v). The regulated pollutants and the particulate matter emissions were evaluated over the European ECE R47 driving cycle on the chassis dynamometer bench. Particulate matter was characterized in terms of total mass collected on filters and total number ofparticles in the range 7 nm-10 microm measured by electrical low-pressure impactor (ELPI). In addition, particle-phase polycyclic aromatic hydrocarbons (PAHs) emissions were evaluated to assess the health impact of the emitted particulate. Finally, an accurate morphological analysis was performed on the particulate by high-resolution transmission electron microscope (TEM) equipped with a digital image-processing/data-acquisition system. In general, CO emission reductions of 60-70% were obtained with 15 and 20% v/v ethanol blends, while the ethanol use did not reduce hydrocarbon (HC) and NOx emissions. No evident effect of ethanol on the particulate mass emissions and associated PAHs emissions was observed. Twenty-one PAHs were quantified in the particulate phase with emissions ranging from 26 to 35 microg/km and benzo[a]pyrene equivalent (BaPeq) emission factors from 2.2 to 4.1 microg/km. Both particulate matter and associated PAHs with higher carcinogenic risk were mainly emitted in the submicrometer size range (<0.1 microm). On the basis of the TEM observations, no relevant effect of the ethanol use on the particulate morphology was evidenced, showing aggregates composed ofprimary particles with mean diameters in the range 17.5-32.5 nm.

A Brief Review of Poly (Butylene Succinate) (PBS) and Its Main Copolymers: Synthesis, Blends, Composites, Biodegradability, and Applications.

PBS, an acronym for poly (butylene succinate), is an aliphatic polyester that is attracting increasing attention due to the possibility of bio-based production, as well as its balanced properties, enhanced processability, and excellent biodegradability. This brief review has the aim to provide the status concerning the synthesis, production, thermal, morphological and mechanical properties underlying biodegradation ability, and major applications of PBS and its principal copolymers.

Purple non-sulfur bacteria as cell factories to produce a copolymer as PHBV under light/dark cycle in a 4-L photobioreactor.

The present study reports a strategy to produce polyhydroxyalkanoates (PHAs) by culturing the marine bacterium Rhodovulum sulfidophilum DSM-1374. The study was carried out by growing the bacterium anaerobically for 720 h under 16/8 light/dark cycle. Two analytical techniques such as proton magnetic nuclear magnetic resonance (1H NMR) and Fourier transform infrared spectroscopy (FT-IR) were used to determine that the polyester produced was poly-3-hydroxybutirate-co-3-hydroxyvalerate (PHBV). This study showed that the excess of lactate and the limitation of N-P nutrients under a light-dark cycle enhanced PHBV synthesis and achieved a PHBV concentration of 330 mg/L in the R. sulfidophilum culture. During the 30 days of bacterial cultivation, the percentage of polymer in the six harvested dry biomasses gradually increased from 13.7% to 23.4%. In addition, the study showed that PHBV synthesis stopped during the 8-h dark phase and restarted in the light. The light-dark cycle study also showed that R. sulfidophilum DSM-1374 can be grown outdoors because the cells are exposed to the natural light-dark cycle.

Recovery of sulfur from sulfur-rich filter cakes in a rotary kiln: Process optimization.

In this work, sulfur recovery from sulfur-rich wastes deriving from sulfur filtration was investigated through laboratory experiments and full-scale tests in an industrial combustion rotary kiln, where elemental sulfur is converted to SO2 in a sulfuric acid production plant. Phase equilibria experiments carried out in the temperature range 1100-1400 °C and industrial scale tests demonstrated that temperature is the most important operating parameter in determining the recovery efficiency and the plant operability. The full-scale tests performed on the rotary kiln showed that, at operating temperatures around 1200 °C, a continuous sulfur recovery from the filter cakes was obtained with an average efficiency of 87% and a consequent reduction of about 70% of the solid waste material to be disposed as inert in landfills or used in cement/glass industries. The efficiency of sulfur recovery increases with the increasing operating temperature but, above 1300 °C, the melting of the residual Ca-Fe-Al-silicate phase and the eventual recrystallization at the kiln refractory walls occurred, causing a forced plant shutdown. The chemical-physical interaction between the sulfur-rich filter cake and different refractory materials was further investigated in the temperature range 1100-1300 °C. At the recommended operation temperatures of 1100-1200 °C, the interaction between the refractory material and the combustion ashes is negligible for all tested materials. Nonetheless, the use of Fe- and Cr-free refractory materials for the internal lining of the kiln must be preferred to minimize the deposition/adhesion of Ca-Fe-Al-silicates derived from combustion over long-term operation.

Extraction of Polyhydroxyalkanoates from Purple Non-Sulfur Bacteria by Non-Chlorinated Solvents.

In this study, non-chlorinated solvents such as cyclohexanone (CYC) and three ionic liquids, (ILs) (1-ethyl-3-methylimidazolium dimethylphosphate, [EMIM][DMP], 1-ethyl-3-methylimidazolium diethylphosphate, [EMIM][DEP] and 1-ethyl-3-methylimidazolium methylphosphite, [EMIM][MP]) were tested to extract polyhydroxyalkanoates (PHAs) from the purple non-sulfur photosynthetic bacterium (PNSB) Rhodovulumsulfidophilum DSM-1374. The photosynthetic bacterium was cultured in a new generation photobioreactor with 4 L of working volume using a lactate-rich medium. The extracted PHAs were characterized using a thermogravimetric analysis, differential scanning calorimetry, infrared spectroscopy, proton nuclear magnetic resonance and gel permeation chromatography. The most promising results were obtained with CYC at 125 °C with an extraction time of above 10 min, obtaining extraction yields higher than 95% and a highly pure poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB-HV) with around 2.7 mol% of hydroxylvalerate (HV). A similar yield and purity were obtained with chloroform (CHL) at 10 °C for 24 h, which was used as the referent solvent Although the three investigated ILs at 60 °C for 4 and 24 h with biomass/IL up to 1/30 (w/w) obtained PHAs strongly contaminated by cellular membrane residues, they were not completely solubilized by the investigated ILs.

On the Use of Paper Sludge as Filler in Biocomposites for Injection Moulding.

The potential use of paper sludge (PS) as filler in the production of bio-composites based on poly lactic acid (PLA) and polybutylene adipate terephthalate (PBAT) was investigated. PS/PLA/PBAT composites, with addition of acetyl tributyl citrate (ATBC) as biobased plasticizer, were produced with PS loadings up to 30 wt.% by twin-screw extrusion followed by injection moulding. The composites were characterized by rheological measurements, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and mechanical tests (tensile and impact resistance) to study the effect of PS on the processability, thermal stability, crystallinity and mechanical performance of polymeric matrix. The optimized composites at higher PS content were successfully processed to produce pots for horticulture and, in view of this application, preliminary phytotoxicity tests were conducted using the germination test on Lepidium sativum L. seeds. Results revealed that developed composites up to 30 wt.% PS had good processability by extrusion and injection moulding showing that PS is a potential substitute of calcium carbonate as filler in the production of bio-composites, and the absence of phytotoxic effects showed the possibility of their use in the production of pots/items for applications in floriculture and/or horticulture.

Microbial communities of polyhydroxyalkanoate (PHA)-based biodegradable composites plastisphere and of surrounding environmental matrix: a comparison between marine (seabed) and coastal sediments (dune sand) over a long-time scale.

Most researches on the plastisphere in coastal environments deal with plastics floating in seawater. Comparatively smaller attention has been devoted to the plastisphere of plastics buried in marine sediments, and very little is known on that of plastics on coastal sand dunes. Yet, limited information is available on the impact of plastics, especially biodegradable plastics, on microbial organisms in their surroundings. Nevertheless, a large amount of plastics sink on the seabed or is deposited on beach-dune systems. We investigated the succession of plastisphere microbial community on two biodegradable composites based on poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) and seagrass fibres (PHBV/PO), buried in seabed and dune sediments over a 27 months period in mesocosm. PHBV is regarded as a valuable alternative to conventional plastics and PHBV/PO has recently been designed for applications in coastal habitat restoration. We also examined the degradation rate and impact of these plastics on the microbial communities of surrounding sediments. Microbial communities of the surface of PHBV and PHBV/PO in seabed and dune sand differ from those of surrounding sediments, displaying a lower richness. Plastics colonization occurs largely from bacteria present in surrounding sediments, although the contribution from the water column bacterial pool could be not negligible for plastics in the seabed. No significant differences were detected between the communities of the two plastics and no significant impact of plastics on microbial community of the surrounding sediments was detected. The exceptional long duration of this study allowed to gain information on the succession of a plastisphere community over a previously unexplored time scale. Succession appears highly dynamic in dune sand even after two years, while the community structure in seabed seems to reach stability after one year. These findings highlight the importance of performing long-term studies when trying to characterize composition and dynamics of plastisphere bacterial communities.

On the Use of Biobased Waxes to Tune Thermal and Mechanical Properties of Polyhydroxyalkanoates-Bran Biocomposites.

In this work, processability and mechanical performances of bio-composites based on poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) containing 5, 10, and 15 wt % of bran fibers, untreated and treated with natural carnauba and bee waxes were evaluated. Wheat bran, the main byproduct of flour milling, was used as filler to reduce the final cost of the PHBV-based composites and, in the same time, to find a potential valorization to this agro-food by-product, widely available at low cost. The results showed that the wheat bran powder did not act as reinforcement, but as filler for PHBV, due to an unfavorable aspect ratio of the particles and poor adhesion with the polymeric matrix, with consequent moderate loss in mechanical properties (tensile strength and elongation at break). The surface treatment of the wheat bran particles with waxes, and in particular with beeswax, was found to improve the mechanical performance in terms of tensile properties and impact resistance of the composites, enhancing the adhesion between the PHBV-based polymeric matrix and the bran fibers, as confirmed by predictive analytic models and dynamic mechanical analysis results.

Hydroxytyrosol rich-mixture from olive mill wastewater and production of green products by feeding Rhodopseudomonas sp. S16-FVPT5 with the residual effluent.

This study disserts on the exploitation of olive mill wastewater (OMW) for the production of both bio-based poly-ß-hydroxybutyrate (PHB) and hydrogen (H2) by using the residual effluent as feedstock for growing purple bacteria after the recovery of hydroxytyrosol-rich mixtures. In particular, Rhodopseudomonas sp. S16-FVPT5 was fed with either the virgin OMW or dephenolized-OMW (d-OMW). For polyphenols removal, the OMW was treated with activated carbon; subsequently, acidified ethanol (pH = 3.1) at 50 °C was used as extractor solvent for obtaining hydroxytyrosol-rich mixtures. The maximum hydroxytyrosol content in the resultant polyphenolic mixture was 2.02 g/L. The highest co-production of PHB (315 mg PHB/L) and H2 (2236 mL H2/L) were achieved feeding Rhodopseudomonas sp. S16-FVPT5 with pure d-OMW. The highest hydrogen yield (4.55 L(H2)/Ld-OMW) was obtained feeding the bacterium with d-OMW, diluted at 25%; by increasing the content of d-OMW into the culture broth the hydrogen yield progressively decreased. Lower results were obtained by feeding the bacterium with a synthetic medium, the cumulative hydrogen was 1855 mL H2/L); the PHB was 101 mg PHB/L. The highest theoretical light conversion efficiency was 2.36% with the synthetic medium and 1.99% when feeding Rhodopseudomonas sp. S16-FVPT5 with d-OMW diluted with water 50%, v/v.

Whey and molasses as inexpensive raw materials for parallel production of biohydrogen and polyesters via a two-stage bioprocess: New routes towards a circular bioeconomy.

Consecutive dark-fermentation and photo-fermentation stages were investigated for a profitable circular bio-economy. H2 photo-production versus poly(3-hydroxybutyrate) (P3HB) accumulation is a modern biotechnological approach to use agro-food industrial byproducts as no-cost rich-nutrient medium in eco-sustainable biological processes. Whey and molasses are very important byproducts rich in nutrients that lactic acid bacteria can convert, by dark-fermentation, in dark fermented effluents of whey (DFEW) and molasses (DFEM). These effluents are proper media for culturing purple non-sulfur bacteria, which are profitable producers of P3HB and H2. The results of the present study show that Lactobacillus sp. and Rhodopseudomonas sp. S16-VOGS3 are two representative genera for mitigation of environmental impact. The highest productivity of P3HB (4.445 mg/(L·h)) was achieved culturing Rhodopseudomonas sp. S16-VOGS3, when feeding the bacterium with 20% of DFEM; the highest H2 production rate of 4.46 mL/(L·h) was achieved when feeding the bacterium with 30% of DFEM.