RESUMO
Compared to pressfit cups, little information exists about the results of screwed cups in hip arthroplasty. 51 cementless or hybrid (cemented stem) primary total hip replacements with a cementless corundium blasted titaniumn alloy threaded Aesculap Munich II type cup were examined with a mean follow up of 7.9 years. 23 of the patients were male and 28 patients were female. From these cups 22 were implanted on the right side and 29 on the left. The results were compared to 53 patients (28 male, 25 female, 29 right side, 24 left side) with the threaded Aesculap Munich I type cup, that has a smooth surface and a direct contact of bone with the polyethylene inlay. The mean follow up ws 10.2 years. The early and medium to long-term clinical and radiographic results show an encouraging improvement of the Merle d'Aubigné Score of the type II cup compared to the type I cup. Two of the Aesculap type Munich II cups had to be revised; four showed radiologic signs of loosening. In conclusion, the threaded Aesculap cup type Munich II seems to be a decisive advance in the development of threaded acetabular hip cups. The intermediate results exceed those from smooth-surface screwed rings and compare favourably with those from cemented cups and with those from cementless press-fit metal-backed cups.
Assuntos
Artroplastia de Quadril/instrumentação , Prótese de Quadril , Acetábulo , Adulto , Idoso , Idoso de 80 Anos ou mais , Artroplastia de Quadril/métodos , Cimentos Ósseos , Feminino , Seguimentos , Humanos , Masculino , Pessoa de Meia-Idade , Desenho de Prótese , Falha de Prótese , Resultado do TratamentoRESUMO
One complication of rheumatoid arthritis (RA) is the involvement of the cervical spine (CS). Although prophylactic stabilisation is recommended, the timing at which this should occur is poorly defined. The aim of our study was to evaluate the course of neurological symptoms in terms of the timing of surgery. A total of 34 patients with RA and CS involvement were surgically stabilised. These patients were classified using the Ranawat (RW) score both preoperatively and at an average of 54 months post-operatively. For each patient, the presence of atlantoaxial and subaxial subluxation as well as vertical migration of the odontoid was recorded. The anterior atlantodental interval was also assessed pre- and post-operatively. Improvement was obtained in 20 patients, the clinical situation remained unchanged in three patients and three patients manifested disease progression. In terms of the RW score, the 16 patients with pre-operative RW grades I-II showed no deterioration at the post-operative follow-up, with 13 of these patients showing an improvement; the 12 patients with pre-operative RW grades IIIA-IIIB did not show any improvement of neurological symptoms at follow-up, although seven of these patients subjectively assessed the symptoms to be less severe after surgery; three other patients showed a worsening of symptoms. Our results suggest that preventive stabilisation of CS in RA leads to acceptable results, although the complications of the surgery are obvious. However, early operative treatment may delay the detrimental course of cervical myelopathy in RA.
Assuntos
Artrite Reumatoide/cirurgia , Vértebras Cervicais/cirurgia , Fusão Vertebral/métodos , Adulto , Idoso , Artrite Reumatoide/diagnóstico por imagem , Articulação Atlantoaxial/diagnóstico por imagem , Articulação Atlantoaxial/cirurgia , Vértebras Cervicais/diagnóstico por imagem , Feminino , Humanos , Luxações Articulares/diagnóstico por imagem , Luxações Articulares/cirurgia , Masculino , Pessoa de Meia-Idade , Processo Odontoide/diagnóstico por imagem , Processo Odontoide/cirurgia , Radiografia , Fatores de Tempo , Resultado do TratamentoRESUMO
INTRODUCTION: The two available computer-assisted surgery robotic systems consist of a preoperative planning computer workstation and an industrial robot with a high speed milling device. During the computed tomography (CT) scan of the hip and the ipsilateral knee for planning the hip arthroplasty, the patient's movements are registered by a bar that is fixed at the patient's leg along its axis. Despite the companies' claim that a high accuracy of implant position can be achieved by this method, misplacements of implants are reported in the literature. MATERIALS AND METHODS: In an experimental study, a cadaver femoral bone was rotated during the CT scan strictly around this bar to simulate a rotational movement of the patient. Using the CT data, the planning of the hip stem and the following preparation of the femur by the robot was possible without detection of the patient's movements by the system. According to the system manual, the computer should stop the planning or give a warning in case of patient movement during the CT scan. RESULTS: The postoperative CT scan of the cadaver femoral bone revealed a rotary deviation and a shift of the stem compared with the original planning, caused by the rotation during the CT scan. CONCLUSION: We propose using a second bar during the CT scan to detect these movements and thus avoiding misplacement of the implant.