RESUMO
In this work, the production of thick ceramic LiCoO2 (LCO) electrodes using a conventional desktop 3D-printing was developed as an alternative to conventional electrode manufacturing for Li-ion batteries. Firstly, the filament formulation, based on LCO powders and a sacrificial polymers blend, is optimized to achieve suitable features (viscosity, flexibility and mechanical consistency) to be used in the 3-D printing. Printing parameters were optimized to produce defect-free bodies with coin geometry (12 mm diameter and 230-850 µm thickness). Thermal debinding and sintering were studied in order to obtain all ceramic LCO electrodes with adequate porosity. The additive-free sintered electrodes (850 µm thickness) have enhanced areal and volumetric capacities (up to 28 mA·h·cm-2 and 354 mA·h·cm-3) due to their extremely high mass loading (up to 285 mg·cm-2). Thus, the Li//LCO half-cell delivered an energy density of 1310 W·h·L-1. The ceramic nature of the electrode permits the use of a thin film of paint gold as current collector, reducing considerably the polarization of thick electrodes. Thus, the whole manufacturing process developed in this work is a complete solvent-free method to produce tuneable shape electrodes with enhanced energy density, opening the door for the manufacturing of high-density batteries with complex geometries and good recyclable.
RESUMO
Influence of the vacancy concentration on the Li conductivity of the (Li(1-x)Na(x))(0.2)La(0.6)TiO(3) and (Li(1-x)Na(x)(0.5)La(0.5)TiO(3) perovskite series, with 0 < or = x < 1, has been investigated by neutron diffraction (ND), impedance spectroscopy (IS), nuclear magnetic resonance (NMR), and Monte Carlo simulations. In both series, Li(+) ions occupy unit cell faces, but Na(+) ions are located at A sites of the perovskite. From this fact, the amount of vacant A sites that participate in Li conductivity is given by the expression n(v) = [Li] + square, where square is the nominal vacancy concentration. Substitution of Li by Na decreases the amount of vacancies, reducing drastically the Li conductivity when n(v) approaches the percolation threshold of the perovskite conduction network. In disordered (Li(1-x)Na(x))(0.5)La(0.5)TiO(3) perovskites, the percolation threshold is 0.31; however, in ordered (Li(1-x)Na(x))(0.2)La(0.6)TiO(3) perovskites, this parameter changes to 0.26. Near the percolation threshold, the amount of mobile Li species deduced by (7)Li NMR spectroscopy is lower than that derived from structural formulas but higher than deduced from dc conductivity measurements. Conductivity values have been explained by Monte Carlo simulations, which assume a random walk for Li ions in the conduction network of the perovskite. In these simulations, distribution of vacancies conforms to structural models deduced from ND experiments.
RESUMO
Lithium cations sit in the center of the oxygen "windows" defined by the vertex-sharing TiO(6) octahedra of the title compound (see picture), as shown from neutron diffraction data. The octahedra are tilted to optimize the bond distances between the atoms. The unusual coordination and the partially unoccupied sublattice (occupancy factors 1/6 and (1/2) for Li and La, respectively) account for the high mobility of the Li(+) cations.
RESUMO
We have analyzed the constant loss contribution to the ac conductivity in the frequency range 10 Hz-1 MHz and temperatures down to 8 K, for two Li ionic conductors, one crystalline (Li(0.18)La(0.61)TiO(3)) and the other glassy (61SiO(2);35Li(2)O.3Al(2)O3.P(2)O(5)). As temperature is increased a crossover is observed from a nearly constant loss to a fractional power law frequency dependence of the ac conductivity. At any fixed frequency omega, this crossover occurs at a temperature T such that omega approximately nu(0)exp(-E(m)/k(B)T), where nu(0) is the attempt frequency and E(m) is identified with the barrier for Li+ ions to leave their wells.