Large-scale surface water-groundwater origins and connectivity in the Ordos Basin, China: Insight from hydrogen and oxygen isotopes.

The sustainability of water resources is a major challenge for the Ordos Basin and Loess Plateau of China. The basis of effective water management is an understanding of the water cycle process. This study investigated the surface water-groundwater origins and connectivity using stable isotopes (δD and δ18O) of surface water and groundwater in 11 river basins in the Ordos Basin. It was found that the surface water-groundwater origins and hydraulic connection were characterized by regional differences, mainly induced by climatic characteristics, hydrogeological conditions and human activities. Specifically, the impact of thick loess deposits caused surface water and groundwater to take long time to produce a hydraulic connection. In contrast, areas with thin loess deposits and frequent human activities showed a good connectivity between surface water and groundwater. As for water origins, summer precipitation was a common source of surface water and groundwater in the study area, and groundwater discharge was another source of surface water. However, surface water and groundwater were subjected to different degrees of evaporation during receiving precipitation recharge. Notably, thick loess deposits had an impact on groundwater evaporation because both the recharge of precipitation to groundwater and the discharge of groundwater to surface water took a long time. In addition, it was found that frequent human activities (mining, irrigation and urban construction) could weaken the impact of evaporation. This large-scale analysis provided new insights into the origins and connectivity of surface water and groundwater in areas with thick unsaturated zones for water resources management.

A novel electrochemical sensor based on autotropic and heterotrophic nitrifying biofilm for trichloroacetic acid toxicity monitoring.

Trichloroacetic acid (TCA), a toxic substance produced in the disinfection process of wastewater treatment plants, will accumulate in the receiving water. The detection of TCA in the water can achieve the purpose of early warning. However, currently there are few reports on microbial sensors used for TCA detection, and the characteristics of their microbial communities are still unclear. In this work, a toxicity monitoring microbial system (TMMS) with nitrifying biofilm as a sensing element and cathode oxygen reduction as a current signal was successfully constructed for TCA detection. The current and nitrification rate showed a linear relationship with low TCA concentration from 0 to 50 µg/L (R2current = 0.9892, R2nitrification = 0.9860), and high concentration range from 50 to 5000 µg/L (R2current = 0.9883, R2nitrification = 0.9721). High-throughput sequencing revealed that the TMMS was composed of autotrophic/heterotrophic nitrifying and denitrifying microorganisms. Further analysis via symbiotic relationship network demonstrated that Arenimonas and Hyphomicrobium were the core nodes for maintaining interaction between autotropic and heterotrophic nitrifying bacteria. Kyoto Encyclopedia of Genes and Genomes analysis showed that after adding TCA to TMMS, the carbon metabolism and the abundance of the tricarboxylic acid cycle pathway were reduced, and the activity of microorganisms was inhibited. TCA stress caused a low abundance of nitrifying and denitrifying functional enzymes, resulting in low oxygen consumption in the nitrification process, but more oxygen supply for cathode oxygen reduction. This work explored a novel sensor combined with electrochemistry and autotrophic/heterotrophic nitrification, which provided a new insight into the development of microbial monitoring of toxic substances.

Risk assessment for and microbial community changes in Farmland soil contaminated with heavy metals and metalloids.

Food security and human health can be seriously affected by heavy metal and metalloid (HM) pollution of soil. In this study, the risks posed by HMs and microbial community responses to HM pollution of agricultural soil in southwestern China were investigated. The C, N, P, and S (nutrients) concentrations were 12040.7-15912.7, 1298.06-1832.01, 750.91-2050.35, and 269.17-2115.52 mg/kg, respectively. The As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn concentrations were 3.11-8.20, 1.85-6.56, 22.83-43.96, 11.21-23.30, 0.08-0.81, 11.02-22.97, 24.07-42.96, and 193.63-698.39 mg/kg, respectively. Interpolation analysis indicated that the nutrient and HM concentrations varied spatially rather strongly. The concentrations of all of the elements were higher in soil from the northern sampling sites than in soil from the other sites. HMs in soil were found to pose high levels of risk (RI 898.85, i.e., >600). Cd contributed more than the other HMs to the risk assessment values (ErCd 293.72-1031.94), so was the most serious contaminant. Microbial diversity decreased over time in soil with high HM concentrations (plot S2) and was lower than in soil with low HM concentrations (plot S8). The nutrient and HM concentrations correlated with the microbial community characteristics. Proteobacteria, Acidobacteria, and Chloroflexi were (in decreasing order) the dominant bacterial phyla. We speculate that these phyla may be strongly resistant to HMs. The fourth most common phylum was Actinobacteria. Bacteria in this phylum could be used as biological indicators of the HM pollution status. Soil micro-ecosystems can self-regulate. HM stress will affect the evolution of soil microorganisms and relevant functional genes. The spatiotemporal variability in the microbial community responses to HMs and the spatial analysis and ecological risk assessment results will be useful reference data for the remediation of HM-polluted soil.

Effect of air-exposed biocathode on the performance of a Thauera-dominated membraneless single-chamber microbial fuel cell (SCMFC).

To investigate the effect of air-exposed biocathode (AEB) on the performance of single-chamber microbial fuel cell (SCMFC), wastewater quality, bioelectrochemical characteristics and the electrode biofilms were researched. It was demonstrated that exposing the biocathode to air was beneficial to nitrogen removal and current generation. In Test 1 of 95% AEB, removal rates of ammonia, total nitrogen (TN) and chemical oxygen demand (COD) reached 99.34%±0.11%, 99.34%±0.10% and 90.79%±0.12%, respectively. The nitrogen removal loading rates were 36.38gN/m3/day. Meanwhile, current density and power density obtained at 0.7A/m3 and 104mW/m3 respectively. Further experiments on open-circuit (Test 2) and carbon source (Test 3) indicated that this high performance could be attributed to simultaneous biological nitrification/denitrification and aerobic denitrification, as well as bioelectrochemical denitrification. Results of community analysis demonstrated that both microbial community structures on the surface of the cathode and in the liquid of the chamber were different. The percentage of Thauera, identified as denitrifying bacteria, maintained at a high level of over 50% in water, but decreased gradually in the AEB. Moreover, the genus Nitrosomonas, Alishewanella, Arcobacter and Rheinheimera were significantly enriched in the AEB, which might contribute to both enhancement of nitrogen removal and electricity generation.

The saci_2123 gene of the hyperthermoacidophile Sulfolobus acidocaldarius encodes an ATP-binding cassette multidrug transporter.

Multidrug resistance (MDR) transporters are capable of secreting structurally and functionally unrelated toxic compounds from the cell. Among this group are ATP-binding cassette (ABC) transporters. These membrane proteins are typically arranged as either hetero- or homo-dimers of ABC half-transporters with each subunit consisting of a membrane domain fused at the C-terminus to an ATP-binding domain, or as full transporters in which the two subunits are fused into a single polypeptide. The saci_2123 gene of the thermoacidophilic archaeon Sulfolobus acidocaldarius is the only gene in the genome that encodes an ATP-binding cassette half-transporter, while a homologous gene is present in the genomes of S. solfataricus, S. tokodaii and S islandicus. Saci_2123 shares homology with well-characterized bacterial and mammalian MDR transporters. The saci_2132 gene is up-regulated when cells are exposed to drugs. A deletion mutant of saci_2132 was found to be more vulnerable to a set of toxic compounds, including detergents, antibiotics and uncouplers as compared to the wild-type strain, while the drug resistance could be restored through the plasmid-based expression of saci_2132. These data demonstrate that Saci_2132 is an archaeal ABC-MDR transporter and therefore it was termed Smr1 (Sulfolobus multidrug resistance transporter 1).

Deletion of cdvB paralogous genes of Sulfolobus acidocaldarius impairs cell division.

The majority of Crenarchaeota utilize the cell division system (Cdv) to divide. This system consists of three highly conserved genes, cdvA, cdvB and cdvC that are organized in an operon. CdvC is homologous to the AAA-type ATPase Vps4, involved in multivesicular body biogenesis in eukaryotes. CdvA is a unique archaeal protein that interacts with the membrane, while CdvB is homologous to the eukaryal Vps24 and forms helical filaments. Most Crenarcheota contain additional CdvB paralogs. In Sulfolobus acidocaldarius these are termed CdvB1-3. We have used a gene inactivation approach to determine the impact of these additional cdvB genes on cell division. Independent deletion mutants of these genes were analyzed for growth and protein localization. One of the deletion strains (ΔcdvB3) showed a severe growth defect on plates and delayed growth on liquid medium. It showed the formation of enlarged cells and a defect in DNA segregation. Since these defects are accompanied with an aberrant localization of CdvA and CdvB, we conclude that CdvB3 fulfills an important accessory role in cell division.

Accuracy of Endorectal Endoscopic Ultrasound (EUS) for Locally Advanced Rectal Cancer (LARC) Restaging After Neoadjuvant Chemoradiotherapy (NAT): A Meta-Analysis.

BACKGROUND/AIMS: Endorectal endoscopic ultrasound (EUS) can provide accurate and reliable information for initial staging of locally advanced rectal cancer (LARC) in both the depth of rectal cancer penetration (T-stage) and regional lymph node involvement (N-stage). However, there is still no consensus about its accuracy in retagging LARC after neoadjuvant chemoradiotherapy (NAT). METHODOLOGY: In this study, we retrieved previous studies and performed a meta-analysis for assessing the accuracy of EUS for retagging of LARC after NAT. RESULTS: It was found the accuracy of EUS for T restaging of LARC was relatively low and over-staging was common, although the accuracy for assessing T3/4 was significantly higher than T0-T2 stage. The specificity of EUS for assessing N stage was relatively high, but the sensitivity was relatively low. CONCLUSIONS: Data obtained in this study confirmed the overall accuracy of EUS is not sufficient to serve as a basis for decisions on restaging Exploring the possible application of new techniques is necessary for better restaging.

Triple isotopes (δD, δ18O, δ17O) characteristic of river water and groundwater in an arid watershed from Qaidam Basin, Northwestern China: implications for hydrological cycle.

Combining traditional stable isotopes (δD and δ18O) and triple oxygen isotope (δ17O) is conducive to tracing hydrological cycle processes. The application of triple oxygen isotopes primarily focuses on precipitation, which is lacking in river water and groundwater. In this study, the spatial variations of δD, δ18O, δ17O, d-excess and 17O-excess of river water and groundwater in the Golmud River basin as well as the correlation between them were investigated to elucidate water origin and assess the evaporation influence on water bodies during flood season. Spatial changes in δD, δ18O and δ17O of river water exhibit a decrease-increase-stability pattern contrary to that observed for d-excess, 17O-excess has no distinct trend but is higher at both the source and downstream regions. The results show that river water and groundwater originate from precipitation in the mountainous area, and the meltwater in the source region also contribute to the river water with high d-excess and 17O-excess during flood season. The combination of d-excess and 17O-excess reveal that river water is also affected by evaporation and mixing of river water in tributaries. It was found that the river water is recharged in the mountains, undergoes evaporation in the upstream region and leaks into groundwater in the midstream region, which is recharged by the groundwater and evaporated again in the downstream region. This study could provide a more comprehensive understanding of the potential and value of triple oxygen isotopes in the hydrological cycle.

Regulation of archaella expression by the FHA and von Willebrand domain-containing proteins ArnA and ArnB in Sulfolobus acidocaldarius.

The ability of microorganisms to sense and respond to sudden changes in their environment is often based on regulatory systems comprising reversible protein phosphorylation. The archaellum (former: archaeal flagellum) is used for motility in Archaea and therefore functionally analogous to the bacterial flagellum. In contrast with archaellum-mediated movement in certain members of the Euryarchaeota, this process, including its regulation, remains poorly studied in crenarchaeal organisms like Sulfolobus species. Recently, it was shown in Sulfolobus acidocaldarius that tryptone limiting conditions led to the induction of archaella expression and assembly. Here we have identified two proteins, the FHA domain-containing protein ArnA and the vWA domain-containing protein ArnB that are involved in regulating archaella expression in S. acidocaldarius. Both proteins are phosphorylated by protein kinases in vitro and interact strongly in vivo. Phenotypic analyses revealed that these two proteins are repressors of archaella expression. These results represent the first step in understanding the networks that underlie regulation of cellular motility in Crenarchaeota and emphasize the importance of protein phosphorylation in the regulation of cellular processes in the Archaea.

Sustainable energy recovery in wastewater treatment by microbial fuel cells: stable power generation with nitrogen-doped graphene cathode.

Microbial fuel cells (MFCs) recover energy sustainably in wastewater treatment. Performance of non-noble cathode catalysts with low cost in neutral medium is vital for stable power generation. Nitrogen-doped graphene (NG) as cathode catalyst was observed to exhibit high and durable activity at buffered pH 7.0 during electrochemical measurements and in MFCs with respect to Pt/C counterpart. Electrochemical measurements showed that the oxygen reduction reaction (ORR) on NG possessed sustained activity close to the state-of-art Pt/C in terms of onset potential and electron transfer number. NG-MFCs displayed maximum voltage output of 650 mV and maximum power density of 776 ± 12 mW m(-2), larger than 610 mV and 750 ± 19 mW m(-2) of Pt/C-MFCs, respectively. Furthermore, long-time test lasted over 90 days, during which the maximum power density of NG-MFCs declined by 7.6%, with stability comparable to Pt/C-MFCs. Structure characterization of NG implied that the relatively concentrated acidic oxygen-containing groups improved such long-time stability by repelling the protons due to the same electrostatic force, and thus the C-N active centers for ORR were left undestroyed. These findings demonstrated the competitive advantage of NG to advance the application of MFCs for recovering biomass energy in treatment of wastewater with neutral pH.

Insights into moisture sources and evolution from groundwater isotopes (2H, 18O, and 14C) in Northeastern Qaidam Basin, Northeast Tibetan Plateau, China.

Knowledge of moisture sources is of great significance for the understanding of groundwater recharge and hydrological cycle. However, it is often difficult to identify the moisture sources and evolution especially in the areas with complex climate system. Isotopes in groundwater that acts as a climate archive provide a unique perspective on the moisture sources and evolution. In this study, the stable isotopes (2H, 18O) of precipitation and groundwater, radioactive isotope (14C) of groundwater, water vapor trajectory modeling (HYSPLIT models) and d-excess based on mass balance model were employed to reveal the groundwater origin, moisture source and evolution in the northeastern Qaidam Basin, northeast Tibetan Plateau, China. The stable isotopic compositions indicate that the precipitation in the mountainous areas is the main origin of groundwater. The spatiotemporal variation of groundwater d-excess together with HYSPLIT modeling suggest that the moisture sources in the northeastern Qaidam Basin have been controlled by the Westerlies and did not alter obviously with time, whereas Delingha with relatively low elevation is influenced by both the Westerlies and local recycled moisture. More than 80 % water vapor derives from the northwest of study area for the plain and mountainous area, except for the mountainous area of Delingha, where approximately 23 % water vapor originates from the surface water evaporation in the plain area. The water vapor with high d-excess formed in the plain area is transported to the mountainous area and mixed with advected water vapor, resulting in the large d-excess of groundwater in Delingha. The moisture recycling fraction in precipitation for the mountainous area of Delingha is estimated to be about 2.0 % by using d-excess-based mass balance model. The results of the study could be helpful to the understanding of hydrological cycle of the area and elsewhere.

Coupling mixotrophic denitrification and electroactive anodic nitrification by nitrate addition for promoting current generation and nitrogen removal.

Nitrate promotes anodic denitrification and fasts organic matter removal in microbial fuel cells (MFCs). However, it suffers from poor total nitrogen (TN) removal and current recovery. In this study, some novel electroactive nitrifying/denitrifying bacteria (ENDB) were introduced in a single chambered air-cathode MFC to investigate the performance of this device and the microbial community shift by adding nitrate. Results showed a similar disturbance in current output by adding nitrate during a short-term operation. However, a stable and reproducible current increase was achieved in the continuous experiment. A maximum current of 0.76 A m-3 and a maximum TN removal of >99 % were accomplished. The corresponding corrected coulombic efficiency was approximately 18 %. Under repeatable batches, a sharp decrease in chemical oxygen demand (COD) with feeding nitrate confirmed the temporary competition on electron donors through heterotrophic denitrification. The later current increase and nitrite detection occurring without metabolized COD could be considered evidence of electroactive anodic nitrification. The ENDB biofilm successfully coupled mixotrophic denitrification and electroactive anodic nitrification. It eventually promoted TN removal. In the process, genera Pseudoxanthomonas, Thauera, and Pseudomonas were enriched in the anodic ENDB biofilms. Cyclic voltammetry data confirmed the promotion of the electron transfer process by biofilms. The bacterial function predication revealed that the genes related to nitrogen removal and electron transfer were upregulated. Therefore, mixotrophic denitrification and electroactive anodic nitrification processes facilitated power recovery with the high efficiency of pollutant removal, finally ensuring water body security.

Deciphering three-dimensional bioanode configuration for augmenting power generation and nitrogen removal in air-cathode microbial fuel cells.

In this study, the engineering-oriented three-dimensional (3D) bioanode concept was applied, demonstrating that spiral-stairs-like/rolled carbon felt (SCF/RCF) configurations achieved good performances in air-cathode microbial fuel cells (ACMFCs). With the 3D anodes, ACMFCs generated significantly higher power densities of 1535 mW/m3 (SCF) and 1800 mW/m3 (RCF), compared with that of a traditional flat carbon felt anode (FCF, 315 mW/m3). The coulombic efficiency of 15.39 % at SCF anode and 14.34 % at RCF anode also is higher than the 7.93 % at FCF anode. The 3D anode ACMFCs exhibited favorable removal of chemical oxygen demand (96 % of SCF and RCF) and total nitrogen (97 % of SCF, 99 % of RCF). Further results show that three-dimensional anode structures could enrich more electrode surface biomass and diversify the biofilm microbial communities for promoting bioelectroactivity, denitrification, and nitrification. These results demonstrate that three-dimensional anodes with active biofilm is a promising strategy for creating scalable MFCs-based wastewater treatment system.

Membrane penetration of nitrogen and its effects on nitrogen removal in dual-chambered microbial fuel cells.

Owing to membrane penetration, a novel route of nitrogen removal was proposed in a dual-chamber microbial fuel cell with a proton exchange membrane (PEM). The results showed that NH4+-N rapidly migrated across PEM with a mass transfer coefficient (KA) of 1.79 ± 0.51 × 10-4 cm s-1, 50% of which was oxidized to NO3--N in the cathode chamber, then the remainder being eliminated by short-cut nitrification/denitrification. Meanwhile, NO3--N went across the PEM again with a low KA of 5.50 ± 0.24 × 10-6 cm s-1, and was subsequently reduced via anodic denitrification. In the anode, the functional microorganisms were divided into exoelectrogenic bacteria (46.2%) and denitrifying bacteria (37.3%), while the dominated bacteria were mainly affiliated with nitrifying bacteria (19.6%) and aerobic denitrifying bacteria (52.9%) in the cathode. These findings provide a new insight into nitrogen removal during bioelectrochemical treatment of actual wastewater.

Aerobic biocathodes with potential regulation for ammonia oxidation with concomitant cathodic oxygen reduction and their microbial communities.

Aerobic biocathodes are effective construct for the simultaneous nitrification and denitrification, but the disturbance of cathodic oxygen reduction on ammonia oxidation and denitrification remains unclear. In this study, we revealed the oxygen reduction peak at -0.4 V (versus silver/silver chloride) by cyclic voltammetry analysis at a cathode without a biofilm. The reduction peak, however, showed a right shift from -0.4 to -0.3 V for the biocathode, indicating that the aerobic biocathode could simultaneously perform traditional nitrification and cathode oxygen reduction. Therefore, different electrode potentials ranging from -0.5 to -0.1 V were designed for regulating the ammonia oxidation rate, and the results showed that the highest oxidation rate reached 3.08 mg/h/L at a potential of -0.2 V under a low-aeration rate of 5 mL/min. High-throughput sequencing showed that Nitrosomonas and Rhodococcus were the dominant nitrogen removal genera in the biocathode, and the abundance of Devosia was related to the interactions between the aeration rate and the electrode potential. Furthermore, the amoC and hao genes responded to aeration and electrode potential regulation, and -0.2 V was more suitable for promoting the denitrification process under low-aeration conditions. Therefore, these findings provided new insights on cathodic potential control for ammonia oxidation and nitrogen removal as well as for the regulation of microbial communities.

Microbial electrochemical driven anaerobic ammonium oxidation coupling to denitrification in a single-chamber stainless steel reactor for simultaneous nitrogen and carbon removal.

Anodic ammonium oxidation mainly focuses on autotrophic process, and the removal combined with organic matter oxidation is still unclear in microbial electrolysis cell (MEC). Here, a stainless-steel tank is constructed as an MEC for anaerobic ammonium oxidation and organic matter removal. Results show that MEC increases ammonium oxidation from 3.83 ± 2.51% to 32.90 ± 3.39%, and the organic matter removal rises from 75.69 ± 0.59% to 92.12 ± 0.57%, and the energy consumption is only 0.80 ± 0.09 kWh kg-1N, indicating an energy-efficient approach for simultaneous ammonium and carbon removal. Cyclic voltammetry reveals two pairs of oxidative peaks (-0.4 V and + 0.6 V) which demonstrate the electrochemical activity of biofilms for organic matter and ammonium oxidation, respectively. 16S rRNA gene analysis clarifies the anodic biofilm mainly enriched by the genus of Azoarcus, Hydrogenophaga and Paracoccus. Further analysis indicates that anodic potential controls the community succession of heterotrophic and hydrogenotrophic denitrifying bacteria, and then regulates the nitrogen and carbon removal processes, which extend the insights of anodic anaerobic ammonium oxidation coupling to denitrification under organic conditions.

Integrated simultaneous nitrification/denitrification and comammox consortia as efficient biocatalysts enhance treatment of domestic wastewater in different up-flow bioelectrochemical reactors.

Simultaneous nitrification/denitrification (SND) can efficiently deplete NH4+ by using air-exposed biocathode (AEB) in bioelectrochemical reactors. However, the fluctuation of wastewater adversely affects the functional biofilms and therefore the performance. In this work, four up-flow bioelectrochemical reactors (UBERs) with some novel inocula were investigated to improve domestic wastewater treatment. The UBERs exhibited favorable removal of chemical oxygen demand (COD, 95%), NH4+-N (99%), and total nitrogen (TN, 99%). The maximum of current (2.7 A/m3), power density (136 mW/m3) and coulombic efficiency (20.5%) were obtained. Cyclic voltammetry analysis showed all the electrodes were of diversified catalytic reactions. Illumina pyrosequencing showed the predominant Ignavibacterium, Thauera, Nitrosomonas, Geminicoccus and Nitrospira were in all electrodes, contributing functional biofilms performing SND, comammox, and bioelectrochemical reactions. FAPROTAX analysis confirmed twenty-one functional groups with obvious changes related to chemoheterotrophy, respiration/oxidation/denitrification of nitrite and nitrate. Comfortingly, such novel diversified consortia in UBERs enhance the microbial metabolisms to treat domestic wastewater.

Electrode-dependent ammonium oxidation with different low C/N ratios in single-chambered microbial electrolysis cells.

Alternative method should be found to solve the ammonia accumulation in anaerobic digestion. Herein, electrode-dependent ammonium oxidation was successfully achieved in anaerobic single-chambered microbial electrolysis cells (MECs)under different low C/N ratios (0, 1, and 1.5), with an applied voltage of 0.6 V as well as an initial NH4+-N and NO3--N concentration of 500 and 300 mg/L. The nitrogen removal performance of MECs and the controls indicated that applying a voltage stimulated nitrogen removal under low C/N ratios of 0, 1, and 1.5. However, the remaining organic carbon in MEC with a relatively higher C/N ratio of 3 inhibited the ammonium oxidation. Current changes and cyclic voltammetry demonstrated that the bioanode with several bioelectrochemical activities could promote ammonium oxidation. The dominant genera Truepera, Aquamicrobium, Nitrosomonas, Arenimonas, Comamonas, and Cryobacterium enriched on both electrodes could be the key functional taxa in MECs with C/N ratios of 0, 1, and 1.5. The remaining sodium acetate in MEC with C/N ratio of 3 inhibits microbial community structure and relative abundance, which may adversely affected nitrogen removal. Further caculation showed that nitrogen balance was essentially achieved, while electron balance was disrupted since electrons may be consumed through NO3--N recycle and cell synthesis, and finally caused low coulombic efficiency.

Comparative evaluation of simultaneous nitritation/denitritation and energy recovery in air-cathode microbial fuel cells (ACMFCs) treating low C/N ratio wastewater.

Air-cathode microbial fuel cells (ACMFCs) can extract available electrons from the low C/N ratio wastewater (LCNW) for pollutant degradation and power generation. However, the multiple effects of operating parameters and their relationship between the performances and parameters are still lacking. In this study, several ACMFCs for simultaneous nitritation/denitritation (SND) and energy recovery were constructed and evaluated in terms of chemical oxygen demand (COD), NH4+-N, C/N ratio, phosphate buffer solution (PBS), and external resistance (Rext), and several derived parameters (e.g., organic loading rate (OLR), nitrogen loading rate (NLR)). Results indicated that ACMFCs could be used to treat LCNW successfully with high pollutant removal rates and sustainable current generation. Maximum removal efficiencies of 94% COD, 92% NH4+-N, and 92% total nitrogen (TN) were achieved. A maximum power density of 1400 mW m-2 and columbic efficiency of 69.2% were also obtained at a low C/N ratio of 1.7-2.6. Low C/N ratios promoted SND by balancing nitritation and denitritation. The microbial community and their predicated function results showed considerable nitrifiers and denitrificans were enriched in the ACMFCs, contributing to SND and power recovery. Further analyses showed that the NH4+-N could inhibit SND, but PBS and Rext had no obvious effects on this outcome. Co-occurrence network analysis demonstrated that power is positively correlated with COD and Rext; strong correlations between organic removal and COD, and between nitrogen removal and ammonia, conductivity, and C/N ratio were also noted. Overall, the appropriate control of such parameters is necessary to achieve efficient SND in ACMFCs for LCNW treatment.

Impact of low temperature on ex situ nitritation/in situ denitritation in field pilot-scale landfill for postclosure care of leachate treatment and gas content.

Leachates and landfill gas (LFG) are the major problems for closed landfills (CL) and cause significant threats to receiving waterbody and ambient air quality. In this study, a field pilot-scale CL with ex situ nitritation/in situ denitritation process was constructed and operated continuously under wide temperature variations. The effect of low temperature on leachate treatment, and LFG content was studied. Results showed that the combined process can efficiently remove nitrogen and organic matters from leachate, and change LFG content under low-temperature condition. In the ex situ nitritaion, maximum removal efficiencies of ammonia and chemical oxygen demand (COD) were over 99% and 85%, respectively. The loading rate of nitrogen and COD reached 0.5 kg N m-3 d-1 and 0.7 kg COD m-3 d-1, respectively. The inhibitions of free ammonia (FA) and free nitrous acid (FNA), and low temperature were the key factors affecting nitritation. With recirculating nitrified leachate, total oxidized nitrogen (TON) was completely reduced, and the refuse decomposition was accelerated. Denitritation was the main reaction responsible in the CL. Additionally, methane content was observed lowly at non-inhibitory TON loading rate of 5.8 ± 3.7 g N ton-1 TS d-1. This decrease was not caused by the increased of TON loading, but a carbon source competition by denitrificans. The estimated COD consumption and methane reduction were 55.0 kg d-1 by TON reduction, and 20 m3 d-1, respectively. Hence, this study served a potential strategy for postclosure care of landfills under low temperature variation.