Effect of gamma sterilization on the properties of microneedle array transdermal patch system.

Soluble microneedles (MNs) of four different hydrophilic polymers namely sodium carboxymethyl cellulose (CMC), polyvinylpyrrolidone (PVP) K30, PVP K90 and sodium hyaluronate (HU) were fabricated by mold casting technique. When exposed to gamma radiation, a dose of 25 kilogray (kGy) was found to render the microneedle (MN) sterile. However, CMC was found to form MNs with poor mechanical properties, whereas PVP K30 MNs were drastically deformed upon exposure to applied dose as observed in bright field microscopy. Scanning electron microscopy (SEM) revealed that morphology of PVP K90 and HU MNs were not significantly affected at the applied dose. The appearances of characteristic peaks of irradiated MNs of PVP K90 and HU in Fourier-transform infrared spectra suggested structural integrity of the polymers on irradiation. Differential scanning calorimetry (DSC) indicated gamma irradiation failed to alter the glass transition temperature and thus mechanical properties of PVP K90 MNs. However, DSC and Powder X-ray Diffraction (PXRD) conclusively indicated that the degree in crystallinity of HU was substantially reduced on irradiation. In vitro dissolution profiles of sterile PVP K90 and HU MNs were similar to un-irradiated MNs with a similarity factor (f2) of 64 and 54, respectively. In vivo dissolution studies in human subjects indicated that sterile MNs of PVP K90 and HU exhibited dissolution of 78.45 ± 1.09 and 78.57 ± 0.70%, respectively, after 20 min. The studies suggested that PVP K90 and HU could be suitable polymers to fabricate soluble MNs as the structural, morphological, microstructural and dissolution properties remained unaltered post γ sterilization.

Characterization of silver nanoparticle in the carboxymethyl cellulose hydrogel prepared by a gamma ray irradiation.

In this study, carboxymethyl cellulose (CMC) hydrogels were traditionally prepared by gamma-ray with an absorbed dose of 50 kGy from a 60Co source. The CMC hydrogels were absorbed and swelled in silver nitrate aqueous solution (0.01 M) by dipping for 1 hour, and then irradiated by gamma-ray at various doses to form silver nanoparticles (Ag NPs). The UV-Vis analysis indicated that the concentration of Ag NPs was enhanced by increasing of absorbed dose from 1 to 5 kGy in this situ reducing system. The FE-SEM and XPS measurements provided further evidence for the successful formation of Ag NPs. These CMC hydrogels stabilized Ag NPs also have been investigated for inhibiting the growth of Staphylococcus aureus and Escherichia coli strains in liquid as well as on solid growth media. The antibacterial tests indicated that the hydrogels containing Ag NPs have antibacterial activity.

Photocatalytic/biodegradable film based on carboxymethyl cellulose, modified by gelatin and TiO2-Ag nanoparticles.

In this study, the composite of carboxymethyl cellulose (CMC) film modified with gelatin and TiO2-Ag nanoparticles (CMC/Gel/TiO2-Ag) was prepared and some properties of synthesized film including physicochemical and photocatalytic properties were investigated. FT-IR results showed that new interactions between the film components were created. Scanning electron microscopy (SEM) results showed that the TiO2-Ag particles with 50-100 nm distributed in the CMC/Gelatin film. The results of the mechanical test showed that the TiO2-Ag nanoparticles at low concentrations increased tensile strength (TS) and decreased strain to break (STB), but with increasing nanoparticles concentrations, TS decreased and STB increased. Photocatalytic study showed that the prepared CMC/Gel/TiO2-Ag film has good photocatalytic property. Gas chromatography was used to study photocatalytic effects of film. Increasing TiO2-Ag nano particles on the film increases the photocatalytic activity of films against NH3, ethanol and benzene.

Ultrasonic degradation of aqueous carboxymethylcellulose: effect of viscosity, molecular mass, and concentration.

It is well established that prolonged exposure of solutions of macromolecules to high-energy ultrasonic waves produces a permanent reduction in viscosity. It is generally agreed as well and also this study proved the hydrodynamic forces to have the primary importance in degradation. According to this study the sonolytic degradation of aqueous carboxymethylcellulose polymer or polymer mixtures is mainly depended on the initial dynamic viscosity of the polymer solution when the dynamic viscosity values are in the area range enabling intense cavitation. The higher was the initial dynamic viscosity the faster was the degradation. When the initial dynamic viscosities of the polymer solutions were similar the sonolytic degradation was dependent on the molecular mass and on the concentration of the polymer. The polymers with high molecular mass or high polymer concentration degraded faster than the polymers having low molecular mass or low polymer concentration. The initial dynamic viscosities were adjusted using polyethyleneglycol.

Duration of TGF-ß3 Exposure Impacts the Chondrogenic Maturation of Human MSCs in Photocrosslinked Carboxymethylcellulose Hydrogels.

Intervertebral disc (IVD) herniation can be caused by both degeneration and traumatic injury, ultimately resulting in back pain or sciatica due to disc protrusion. Replacement of the nucleus pulposus (NP) tissue during surgical intervention post herniation could improve the long-term stability of the functional spinal unit. Tissue engineering strategies may potentially restore both biological and mechanical function of the NP. Recently, photocrosslinked carboxymethylcellulose (CMC) hydrogels were shown to support chondrogenic, NP-like extracellular matrix (ECM) elaboration by human mesenchymal stromal cells (hMSCs) when supplemented with TGF-ß3. However, long-term preconditioning with soluble growth factors in vitro or the use of sustained growth factor delivery vehicles in vivo can be expensive and difficult to control. Transient supplementation with growth factors has been shown to maintain or improve maturation of tissue-engineered constructs. The objective of this study was to evaluate the influence of TGF-ß3 exposure time on hydrogel bulk properties and NP-like matrix elaboration in hMSC-laden CMC hydrogels. Constructs were exposed to TGF-ß3 for 2 weeks (Transient), 8 weeks (Continuous) or 0 weeks (controls). After 8 weeks of culture, both the Transient and Continuous groups exhibited increased ECM accumulation compared to 2 weeks and controls. The Transient group displayed significantly greater accumulation of collagens I and II, while GAG content was significantly higher in the Continuous group by 8 weeks. Distribution of ECM was more homogeneous in the Continuous group, while the Transient group exhibited more concentrated accumulation in the periphery of the hydrogel by 8 weeks. Mechanical properties improved over time in both groups, however, Continuous constructs demonstrated significantly more robust mechanical properties (equilibrium modulus and peak stress) compared to Transient gels at 8 weeks. Although the functional properties of Transient constructs did not surpass those achieved by Continuous scaffolds, they increased and were maintained upon growth factor removal at 2 weeks, and were greater than controls. Additionally, Transient construct mechanical properties (equilibrium modulus, % relaxation) were similar to those of native NP tissue. The differences seen in ECM distribution and subsequent construct functional maturation are likely due to the time available for diffusion of growth factors through the construct. Overall, these findings support the use of short-term TGF-ß3 treatment to promote sufficient long-term tissue maturation in vitro in this hMSC-laden CMC hydrogel system.

Viscoelastic evaluation of topical creams containing microcrystalline cellulose/sodium carboxymethyl cellulose as stabilizer.

The purpose of this study was to examine the viscoelastic properties of topical creams containing various concentrations of microcrystalline cellulose and sodium carboxymethyl cellulose (Avicel(R) CL-611) as a stabilizer. Avicel CL-611 was used at 4 different levels (1%, 2%, 4%, and 6% dispersion) to prepare topical creams, and hydrocortisone acetate was used as a model drug. The viscoelastic properties such as loss modulus (G"), storage modulus (G'), and loss tangent (tan delta) of these creams were measured using a TA Instruments AR 1000 Rheometer and compared to a commercially available formulation. Continuous flow test to determine the yield stress and thixotropic behavior, and dynamic mechanical tests for determining the linear viscosity time sweep data, were performed. Drug release from the various formulations was studied using an Enhancer TM Cell assembly. Formulations containing 1% and 2% Avicel CL-611 had relative viscosity, yield stress, and thixotropic values that were similar to those of the commercial formulation. The elastic modulus (G') of the 1% and 2% formulation was relatively high and did not cross the loss modulus (G"), indicating that the gels were strong. In the commercial formulation, G' increased after preshearing and broke down after 600 seconds. The strain sweep tests showed that for all formulations containing Avicel CL-611, the G' was above G" with a good distance between them. The gel strength and the predominance of G' can be ranked 6% > 4% > 2%. The strain profiles for the 1% and 2% formulations were similar to those of the commercial formulation. The delta values for the 1% and 2% formulations were similar, and the formulations containing 4% Avicel CL-611 had lower delta values, indicating greater elasticity. Drug release from the commercial preparation was fastest compared to the formulations prepared using Avicel CL-611, a correlation with the viscoelastic properties. It was found that viscoelastic data, especially the strain sweep profiles of products containing Avicel CL-611 1% and 2%, correlated with the commercial formulation. Rheological tests that measure the viscosity, yield stress, thixotropic behavior, other oscillatory parameters such as G' and G" are necessary tools in predicting performance of semisolids.

Hydroxyl radical-induced crosslinking and radiation-initiated hydrogel formation in dilute aqueous solutions of carboxymethylcellulose.

Ionizing radiation causes chain scission of polysaccharides in the absence of crosslinking agents. It has been demonstrated before that degradation of carboxyalkylated polysaccharides may be prevented, despite presence of strong electrostatic repulsing forces between chains, at very high polymer concentration in water (paste-like state) when physical proximity promotes recombination of radiation-generated polymer radicals. In such conditions, crosslinking dominates over chain scission and covalent, macroscopic gels can be formed. In an approach proposed in this work, neutralizing the charges on carboxymethylcellulose (CMC) by lowering the pH results in retracting the electrostatic repulsion between chain segments and thus allows for substantial reduction of polymer concentration required to achieve gelation due to domination of crosslinking reactions. Electron-beam irradiation of aqueous solutions of low pH containing 0.5-2% CMC results in hydrogel formation with 70% yield, while both concentration and dose determine their swelling properties. Time-resolved studies by laser flash photolysis clearly indicate strong pH influence on decay kinetics of CMC radicals.

Transforming growth factor-beta 3 stimulates cartilage matrix elaboration by human marrow-derived stromal cells encapsulated in photocrosslinked carboxymethylcellulose hydrogels: potential for nucleus pulposus replacement.

Degeneration of the nucleus pulposus (NP) has been implicated as a major cause of low back pain. Tissue engineering strategies using marrow-derived stromal cells (MSCs) have been used to develop cartilaginous tissue constructs, which may serve as viable NP replacements. Supplementation with growth factors, such as transforming growth factor-beta 3 (TGF-ß3), has been shown to enhance the differentiation of MSCs and promote functional tissue development of such constructs. A potential candidate material that may be useful as a scaffold for NP tissue engineering is carboxymethylcellulose (CMC), a biocompatible, cost-effective derivative of cellulose. Photocrosslinked CMC hydrogels have been shown to support NP cell viability and promote phenotypic matrix deposition capable of maintaining mechanical properties when cultured in serum-free, chemically defined medium (CDM) supplemented with TGF-ß3. However, MSCs have not been characterized using this hydrogel system. In this study, human MSCs (hMSCs) were encapsulated in photocrosslinked CMC hydrogels and cultured in CDM with and without TGF-ß3 to determine the effect of the growth factor on the differentiation of hMSCs toward an NP-like phenotype. Constructs were evaluated for matrix elaboration and functional properties consistent with native NP tissue. CDM supplemented with TGF-ß3 resulted in significantly higher glycosaminoglycan content (762.69±220.79 ng/mg wet weight) and type II collagen (COL II) content (6.25±1.64 ng/mg wet weight) at day 21 compared with untreated samples. Immunohistochemical analyses revealed uniform, pericellular, and interterritorial staining for chondroitin sulfate proteoglycan and COL II in growth factor-supplemented constructs compared with faint, strictly pericellular staining in untreated constructs at 21 days. Consistent with matrix deposition, mechanical properties of hydrogels treated with TGF-ß3 increased over time and exhibited the highest peak stress in stress-relaxation (σ(pk)=1.489±0.389 kPa) at day 21 among all groups. Taken together, these results demonstrate that hMSCs encapsulated in photocrosslinked CMC hydrogels supplemented with TGF-ß3 are capable of elaborating functional extracellular matrix consistent with the NP phenotype. Such MSC-laden hydrogels may have application in NP replacement therapies.

Investigation on radiation degradation of carboxymethylcellulose by ionizing irradiation.

This study was done to compare the effects of irradiations with gamma-rays and electron beams, on the viscosity of the carboxymethylcellulose (CMC), on the functional groups of CMC, and on the production of radicals. It was observed that the relative viscosities decreased as the irradiation doses increased, but the decrease was more significant when irradiation with gamma rays. FT-IR spectra showed no significant difference between the gamma-ray and the electron beam irradiated samples. ESR spectra showed that the gamma-ray irradiation produced more radicals than electron beam irradiation in CMC.

Radiation preparation of PVA/CMC copolymers and their application in removal of dyes.

Copolymer hydrogels composed of poly(vinyl alcohol) (PVA) and carboxymethyl cellulose (CMC) was prepared by using electron beam irradiation as crosslinking agent. The copolymers were characterized by FTIR and the physical properties such as gelation. The thermal behavior and swelling properties of the prepared hydrogels were investigated as a function of PVA/CMC composition. The factors effecting adsorption capacity of acid, reactive and direct dyes onto PVA/CMC hydrogel, such as CMC content, pH value of the dye solution, initial concentration and adsorption temperature for dyes were investigated. Thermodynamic study indicated that the values the negative values of DeltaH suggested that the adsorption process is exothermic. The value of DeltaH (38.81 kJ/mol) suggested that the electrostatic interaction is the dominant mechanism for the adsorption of dyes on hydrogel.