A 3D-simulation study of the deformation, tension, and stress of 3D-printed and conventional denture base materials after immersion in artificial saliva.

INTRODUCTION: The worldwide application of digital technology has presented dentistry with transformative opportunities. The concept of digital dentures, incorporating computer-aided design (CAD) and computer-aided manufacturing (CAM) techniques, holds the promise of improved precision, customization, and overall patient satisfaction. However, the shift from traditional dentures to their digital counterparts should not be taken lightly, as the intricate interplay between oral physiology, patient comfort, and long-term durability requires thorough examination.

Assessment of wear characteristics, longevity and stiffness of Essix-type retainers.

OBJECTIVE: To compare four commercially available Essix-type retainers in terms of longevity, wear characteristics, stiffness and their range of rigidity. MATERIALS AND METHODS: An in vitro study was conducted at Queen Mary University of London. Four groups of thermoplastic materials were included: Duran (PETG), Essix C + (Polypropylene), Vivera and Zendura (Polyurethane). A working typodont was fabricated to evaluate surface wear characteristics using a wear machine with a customized jig. Retainers were measured for tensile test, and water absorption was measured at five different time points up to 6 months after initial immersion in two different physical states and two different solutions. Hydrolytic degradation was also evaluated using FTIR spectroscopy. RESULTS: Essix C + was the most flexible retainer with Vivera the stiffest material. Zendura and Essix C + had the most surface wear (413 µm ± 80 and 652 µm ± 12, respectively) with absorption rates of up to 15 wt% in artificial saliva occurring with Zendura. Only Essix C + displayed signs of degradation following water absorption. CONCLUSIONS: All materials had characteristic levels of flexibility and were susceptible to water absorption. Duran 1.5 mm performed similarly to Vivera in relation to stiffness and wear properties. While Zendura and Vivera have similar chemical structures, they exhibited differences concerning wear resistance and water absorption. Further clinical research evaluating the clinical relevance of these laboratory findings is required. CLINICAL RELEVANCE: Characteristic patterns of wear and rigidity of four commercially available Essix-type retainers were observed. This information should help in the tailoring of retainer material on a case-by-case basis considering treatment-related factors and patient characteristics including parafunctional habits.

Validation of a human saliva model for the determination of leachable monomers and other chemicals from dental materials.

This study aimed to prove the validity of a mixture of chemicals, including salts, small organic molecules, mucin, and α-amylase, as saliva surrogate ("artificial saliva") for assessing leakage of methacrylate monomers and other constituents from dental materials. To achieve this, we developed and validated a liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for the quantification of 2-hydroxyethyl methacrylate (HEMA), triethylene glycol dimethacrylate (TEGDMA), diurethane dimethacrylate (UDMA), bisphenol A glycerolate dimethacrylate (BisGMA), diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide (TPO), bisphenol A (BPA), and five homologues of ethoxylated bisphenol A dimethacrylate (BisEMA EO2-6) in unstimulated and artificial saliva, and compared their concentrations in the two saliva media following either spiking with a mixture of the compounds or incubation of test specimens of printed biomaterials. Test specimens were immersed in unstimulated/artificial saliva, incubated at 37 °C for 24 h, and saliva aliquots were extracted with methanol and subsequently analyzed by LC-MS/MS. The method was validated with regard to matrix effects, linearity, selectivity, lower limits of quantification (LLOQ), precision, bias and combined measurement uncertainty (u'). The performance characteristics of the method were comparable for unstimulated and artificial saliva samples. The combined u' for individual chemicals at a concentration of 10 × LLOQ were within the range of 5.3-14 % for unstimulated saliva and 6.9-16 % for artificial saliva, except for the BisEMA homologues. Combined u' for the latter were 27-74 % in unstimulated saliva, and 27-79 % in artificial saliva. There was no detectable release of BPA from the test specimens, and the TPO concentrations were mainly below the LLOQ. TEGDMA and UDMA were detected in the highest quantities, and at comparable concentrations in the unstimulated and artificial saliva. For all BisEMA homologues, the release was higher in unstimulated saliva than in artificial saliva. The study showed that the artificial saliva model can be a suitable replacement for native saliva, but might underestimate leakage of more lipophilic methacrylates.

Artificial saliva induced structural breakdown of surimi gels with starch under continuous compressive motions.

Food texture perception is dynamic, influenced by food properties and oral processing. Using the Repeatable Dual Extrusion Cell (RDEC), the oral processing dynamics of surimi gel with different corn starch concentrations (0-15%) in the presence of 1 ml artificial saliva or water were studied. The force-time curve showed increased peak forces with higher corn starch concentrations, peaking significantly at 10%, then decreasing at 15%. Salivary amylase played a crucial role in gel sample degradation, especially in samples with 5% starch, with a work value depletion ratio of 0.535 for sample with 1 ml water (SGW-5) and 0.406 for sample with 1 ml saliva (SGS-5). SEM analysis confirmed the formation of a continuous starch network with reduced intermolecular spaces in SGS-5. The starch-iodine complex showed decreasing order with increasing starch concentration, and SGS-5 exhibited the highest degradation rate (61.61 ± 0.92%). Mathematical modeling revealed that initial decay rates (k1) in gel sample decreased with increasing starch concentration, and samples with starch and artificial saliva had higher initial degradation rates. These findings highlight the intricate interplay between saliva and starch in the surimi gel matrix under continuous compressive motions by RDEC apparatus, providing insights for formulating food products with tailored textures properties.

Bonding performance and interfacial adaptation of modern bulk-fill restorative composites after aging in artificial saliva: an in vitro study.

OBJECTIVES: This study aimed at comparing the microtensile bond strength (MTBS) and interfacial adaptation of a modern self-curing and a light-curing restorative bulk-fill composite to a conventional composite applied with the layering technique. METHODS: Forty-eight occlusal cavities were divided in three main groups (16/group) based on tested materials: (i) STELA, bulk-fill self-curing restorative (STELA, SDI Ltd.); (ii) 3 M-BULK, bulk-fill composite (Filtek One Bulk-Fill, 3 M Oral Care); and (iii) 3 M-CTR, a conventional composite (Filtek Supreme XTE, 3 M Oral Care). These were used in combination with their adhesives in self-etch (SE) or etch-and-rinse (ER) mode. Specimens stored in artificial saliva (24 h or 12 months) were evaluated for MTBS and fractography. The interfacial analysis was performed through confocal microscopy. ANOVA and Fisher's LSD post hoc tests were performed with a level of significance of 5%. RESULTS: All the tested materials applied in ER mode presented (24 h) greater bond strength than in SE mode. Although all materials showed a significant drop in the bond strength after prolonged storage, STELA showed the highest bonding performance and interfaces with few gaps. 3 M-BULK had the lowest bond strength and an interface with several voids and gaps. CONCLUSIONS: All materials were affected by interface degradation and bonding reduction over prolonged aging. However, their use in combination with adhesives applied in ER mode may offer greater immediate bonding performance. CLINICAL RELEVANCE: The use of restorative light-curing bulk-fill composites may generate gaps at the bonding interface and voids. STELA may represent a suitable alternative to avoid such issues.

Biocompatibility of dental implants coated with hydroxyapatite using pulsed Er:YAG laser deposition.

We aimed to improve the biocompatibility and osteoinductive potential of Ti implants using a simulated intraoral hydroxyapatite (HAp) coating. We devised a novel surface treatment for aggressive induction of osteoblast adhesion and bone regeneration on the implant surface. A thin α-tricalcium phosphate (α-TCP) film was deposited on the implant surface using a pulsed Er:YAG laser. The coating was converted to HAp through artificial saliva immersion, which was confirmed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). SEM showed needle-like HAp crystals on the Ti disks and sandblasted implant surfaces after immersion in artificial saliva for 96 h. Microcomputed tomography and histological evaluation 4 and 8 weeks after implantation into beagle dog mandibles showed that the HAp-coated implant was biocompatible and exhibited superior osteoinduction compared to that of sandblasted implants. Coating the implant surface with HAp using an Er:YAG laser has potential as a new method of the implant-surface debridement.

Dental composite biodeterioration in the presence of oral Streptococci and extracellular metabolic products.

OBJECTIVE: Secondary caries is a primary cause of early restoration failure. While primary dental caries has been extensively researched, our knowledge about the impact of secondary caries on dental restorations is relatively limited. In this study, we examined how different clinically relevant microbially-influenced environments impact the degradation of nano-filled (FIL) and micro-hybrid (AEL) dental composites. METHODS: Material strength of two commercial dental composites was measured following incubation in aqueous media containing: i) cariogenic (Streptococcus mutans) and non-cariogenic bacteria (Streptococcus sanguinis) grown on sucrose or glucose, ii) abiotic mixtures of artificial saliva and sucrose and glucose fermentation products (volatile fatty acids and ethanol) in proportions known to be produced by these microorganisms, and iii) abiotic mixtures of artificial saliva and esterase, a common oral extracellular enzyme. RESULTS: Nano-filled FIL composite strength decreased in all three types of incubations, while micro-hybrid AEL composite strength only decreased significantly in biotic incubations. The strength of both composites was statistically significantly decreased in all biotic incubations containing both cariogenic and non-cariogenic bacteria beyond that induced by either abiotic mixtures of fermentation products or esterase alone. Finally, there were no statistically significant differences in composite strength decrease among the tested biotic conditions. CONCLUSIONS: The results show that conditions created during the growth of both cariogenic and non-cariogenic oral Streptococci substantially reduce commercial composite strength, and this effect warrants further study to identify the mechanism(s). CLINICAL SIGNIFICANCE: Dental biofilms of oral Streptococci bacteria significantly affect the mechanical strength of dental restorations.

POSS hybrid bioactive glass dental composite resin materials: Synthesis and analysis.

INTRODUCTION: This study create a dental composite by hybirding polyhedral oligo-sesquioxide nano monomers and bioactive glass BG 45S5. METHODS: Make an experimental composite resin material with a 60 % filler content overall by substituting 20 % of the filler with BG 45S5. The experimental resins are grouped and named P0, P2, P4, P6 and P8 based on the reactive nanomonomer methacrylic acid-based multifaceted oligomeric sesquisiloxane (POSS) added by 2 %-8 % in the resin matrix portion of each group. Utilize a universal testing machine to analyze and compare the mechanical properties of these, then perform Fourier infrared spectrum analysis, double bond conversion analysis, and scanning electron microscope analysis. Based on this, after soaking the experimental materials artificial saliva solution or lactic acid solution for a while, the pH changes of the solution, the release of Ca2+ and PO43- ions, and the precipitation of apatite on the resin material's surface were tested and analyzed. Cell viability tests were used to assess sample cell viability and quantify the cytotoxicity of biological cells. The independent sample t-test was used to examine the group comparisons, and a difference was considered statistically significant at P<0.05. RESULTS: Outstanding mechanical and the double bond conversion are demonstrated by the nanocomposites when the POSS concentration hits 4 wt%. Agglomeration will cause the performance to deteriorate if the concentration beyond this threshold. In the P4 group, the double bond conversion, CS, and FS rose by a large margin, respectively, in comparison to the blank control group P0. Thankfully, the data demonstrate that adding POSS increases adhesive ability when compared to the blank group P0, however, there is no discernible difference between the other experimental groups. The acid neutralization capacity of the P4 group is essentially the same as that of the control group (P0). Ca2+ and PO43- ions are released in significant amounts following treatment with lactic acid solution, although this tendency is clearly less pronounced in artificial saliva. SEM and EDX data indicate that when the experimental resin is soaked in lactic acid solution and artificial saliva, apatite precipitation will happen on its surface. The results of the cell viability test indicated that there was no statistically significant difference between the experimental groups, and the viability of the cells increased after 24hours and 48 hours. CONCLUSIONS: POSS was included into the composite resin along with 20% bioactive glass as a filler. When the proportion of POSS is less than 4%, the indices of composite resin materials rise in a dose-dependent way. When this value is surpassed, performance begins to deteriorate. The inclusion of POSS has no influence on the biological activity of the composites, which means that the hybrid composite resin is capable of acid neutralization, ion release, and apatite precipitation. CLINICAL SIGNIFICANCE: The experimental composite resin can be used as an intelligent material in clinical treatment. It has the clinical application potential of preventing demineralization of tooth hard tissue, promoting remineralization, and improving edge sealing through apatite precipitation.

In vitro assessment of dental erosion caused by clear aligners.

The primary objective of this in vitro study was to investigate the erosive potential of enamel under the use of clear aligners (CA), by simulating in vivo conditions experienced by patients who do not remove their CA during the consumption of acidic beverages. In addition, the difference in erosion protection conferred by artificial and human saliva was also evaluated. Sound-extracted human premolars (n = 20) had half of their surfaces protected with acid-resistant nail polish and were randomly distributed into two experimental groups (n = 10): teeth immersed in human saliva or artificial saliva. All teeth had half of their lingual surfaces enclosed by a CA device. The erosive challenges consisted of individual immersion of each sample in citrus acid three times a day, intermediated by immersion in human saliva or artificial saliva for 2 h, during ten days of the erosive protocol. The enamel mineral content was analyzed by high-resolution microtomography. The differential mineral concentration profiles were obtained by subtracting the profile of the mineral concentration of the exposed area and enamel under the CA area from the respective sound area (control). In addition, enamel wear and enamel volume loss were measured. Scanning electron microscopy (SEM) was also performed to analyze the enamel surface. Data were analyzed by two-way ANOVA, followed by the Student-Newman-Keuls test. The enamel wear was higher in teeth immersed in artificial saliva, when compared to human saliva (p < 0.001). The volume loss of the exposed enamel area was lower for tooth immersed in human saliva than in artificial saliva (p < 0.001), during the acid challenge protocol. The use of CA during acid challenges promoted wear and mineral loss of dental enamel, being these changes more pronounced on the enamel surface under the CA. These results open a new path for the development of further studies adopting clinical protocols that promote more accurate responses in the clinical practice during orthodontic treatment.

Morphology, surface characteristics and tribological properties of whey protein/chitosan composite particles and their fat replacing effect in O/W emulsion.

Whey protein isolate (WPI) and chitosan were used to fabricate WPI/chitosan composite particles at temperatures of 75 °C (WPI/chitosan-75) and 95 °C (WPI/chitosan-95). The morphologic structure, surface properties, and the resulting tribological characteristics of the particles were investigated. The composite particles showed larger particle size than pure WPI particles (WPI-75) (~ 509 nm), with WPI/chitosan-95 the largest (932 nm). WPI/chitosan-75 showed complete core-shell structure from microstructure results. The dispersion of WPI/chitosan-75 exhibited higher surface hydrophobicity but lower viscosity compared to WPI/chitosan-95. Tribological analysis revealed that WPI/chitosan composite particles showed dramatically lower friction coefficient (µ) than pure WPI particles at sliding speed <10 mm/s and WPI/chitosan-75 demonstrated superior lubrication effects. With the presence of artificial saliva, the µ of WPI-75 was greatly lowered at sliding speed <16 mm/s, while the values of WPI/chitosan-75 only showed a slight decrease at sliding speed <1 mm/s. Chitosan might have played the similar role as artificial saliva in lubricating on the hydrophobic surface. Moreover, the incorporation of 0.5 % WPI/chitosan-75 in the low-fat (5 %) oil-in-water emulsion led to even lower µ than full-fat (20 %) emulsion at sliding speed <10 mm/s. Hence, WPI/chitosan-75 exhibited promising potential as a fat replacement and biolubricant.

Do Saliva-Saturated Spit Hoods Interfere With Ventilation?

ABSTRACT: Spit hoods are used by law enforcement, officers in correctional facilities, and medical personnel during the restraint of agitated subjects that are actively spitting to prevent the transmission of droplet-transmitted pathogens. We could find no studies reporting on the time course of normal breathing to clear saliva from such a saturated spit hood. We purchased samples of 3 popular spit hood models and applied a section over the output of a pneumatic test system. We used a digital anemometer, digital manometer, and an inline controllable fan for back pressure and flow. The pressure was 3 mm Hg to match quiet breathing. The tested area was saturated with artificial saliva, and air pressure was applied while we recorded the pressure and airflow. Within 5 seconds, the spit hoods all cleared sufficient artificial saliva to allow 1 m/s of airflow, which exceeds that of an N95 mask with similar pressure. Commonly used spit hoods offer very low resistance to breathing even after being initially saturated with artificial saliva. Our results do not support the hypothesis that a saliva-filled spit hood might contribute to death.

In vitro measurement of the retention force of two stud attachment systems during cyclic load.

PURPOSE: To investigate the retentive behavior of the Locator legacy and Novaloc attachment systems with different retention inserts both within and across systems under cyclic load. MATERIALS AND METHODS: Three retention inserts of each system (green, yellow, and white for Novaloc; green, orange, and red inserts for extended range for legacy Locator) were tested on abutments of both systems with a sample number of 10 per force and 10,000 cycles of insertion and removal. The loading was applied in the axial direction of the abutments, which were placed in artificial saliva. The retention force was measured in each cycle. The results were compared with the manufacturer's specifications and evaluated for a simulated period of use of 10 years. Characteristic time constants were determined, and subsequently, the two systems were compared regarding their wear behavior. RESULTS: The manufacturer's specifications could only be confirmed for the green Novaloc retention insert on a Novaloc abutment (t-test: p = 0.50); for all other inserts, the baseline exceeded the manufacturer's specifications by 30%-75% (Novaloc; t-test: p < 0.001) and 75%-550% (Locator; t-test: p < 0.001). After 10,000 cycles performed, the manufacturer's specifications were confirmed on a Novaloc abutment for the white Novaloc retention insert (t-test: p = 0.86) and on a Locator abutment for the green Novaloc retention insert (t-test: p = 0.32). Both systems lost retention force during the experiment. Overall, Novaloc inserts on both abutments showed less wear (decrease to 56%-85% of initial force) and a slower decrease in retention force compared to Locator inserts (decrease to 6%-31% of initial force). CONCLUSIONS: In both systems, wear leads to a varying loss of retention; therefore, regular checks with possible replacement of the inserts are necessary in clinical use. Novaloc attachments seem to be more resistant to the loss of retention than Locator attachments. A cross-combination may be clinically useful in some cases.

Change in surface properties of two different dental resin composites after using various beverages and brushing.

BACKGROUND: The study aimed to evaluate the influence of various beverages; with and without brushing; on the surface mechanical properties of two resin composites. METHODS: A total of 160 disc-shaped specimens were prepared for each of the following dental composites; nanohybrid ormocer (Admira fusion, VOCO GmbH, Cuxhaven, Germany) and nanohybrid resin composite (Grandio, VOCO GmbH, Cuxhaven, Germany). The baseline surface hardness and roughness measurements were carried out after 24 h. The composite samples were randomly distributed into one of the two groups; brushing and non-brushing, which were further divided into one of the four subgroups (n = 10); artificial saliva as control, coffee, red wine, and soft drink. In the non-brushing group, the specimens were immersed in the different beverages for five minutes three times daily for 30 days. The same procedure was done for the brushing group, in addition to brushing the specimens for five seconds. The surface hardness and roughness measurements were repeated after 30 days. One-way ANOVA and independent t-tests were used for statistical analysis. RESULTS: The soft drink had the most deteriorating effect and artificial saliva had the least. The change in surface properties was higher in the brushing subgroups. Grandio exhibited a higher change in surface microhardness while Admira fusion exhibited a higher change in surface roughness. CONCLUSIONS: The surface properties of both dental resin composites were negatively affected by using beverages and brushing.

Berberine-fluconazole microparticle-based combination therapy to treat candidiasis infections.

AIM: This study aims to incorporate alginate microparticles containing berberine and fluconazole into two different types of pharmaceutical formulations, to subsequently evaluate the antifungal activity against Candida albicans. METHODS AND RESULTS: Alginate microparticles containing BBR (berberine) and FLU (fluconazole) were produced by the spray-drying technique, characterized and incorporated in two pharmaceutical formulations, a vaginal cream and artificial saliva. Broth microdilution, checkerboard, time-kill curve, and scanning electron microscopy were carried out to determine the antifungal effects of BBR and FLU against C. albicans. The minimum inhibitory concentration (MIC) and minimum fungicidal concentration (MFC) values of free BBR were 125 µg ml-1. Synergism between BBR and FLU was demonstrated by a fractional inhibitory concentration index (FICI) = 0.0762. The time-kill curve for the combination BBR + FLU showed a more pronounced decrease in fungal growth in comparison to free drugs, and an antibiofilm effect of BBR occurred in the formation and preformed biofilm. CONCLUSION: Alginate microparticles containing BBR and FLU were obtained and incorporated in a vaginal cream and artificial saliva. Both formulations showed good stability, antifungal effects, and organoleptic characteristics, which suggest that BBR-FLU microparticles in formulations have potential as antifungal therapy.

Effect of lactoferrin on enamel characteristics of primary and permanent teeth: an in-vitro study.

BACKGROUND: Lactoferrin, a glycoprotein naturally found in breast milk, is known for its bactericidal and antiviral properties, as well as its capacity to modulate the immune system; therefore, pediatricians routinely recommend it as dietary support. The objective of this study was to determine how lactoferrin oral suspension could affect the enamel surface characteristics of primary and permanent teeth. METHODS: This research was conducted on 40 unidentified extracted teeth, including primary and permanent teeth. Experimental teeth were free of cracks or enamel defects, as confirmed by careful examination using a dental operating microscope. The crowns were bisected into 80 specimens and assorted into two groups based on the type of dentition. Group DM included 40 specimens of second deciduous molars, while Group PM contained 40 samples of first premolars. Each of the DM and PM specimens was subsequently split based on the type of dispersion medium into two subgroups: a control subgroup (artificial saliva) and a test subgroup (lactoferrin suspension). The specimens were immersed in lactoferrin suspension for two minutes, then kept in artificial saliva for the rest of the 24 h for 30 successive days. This is a pioneering study about the effect of orally supplemented lactoferrin on teeth; therefore, we examined enamel hardness, ultra-morphology, and mineral contents. RESULTS: Our findings indicated a highly significant decrease (p < 0.01) in the microhardness of the lactoferrin subgroup in Group DM (second deciduous molars) and a significant reduction (p < 0.05) in the microhardness of the lactoferrin subgroup in Group PM (premolars). Calcium weight% was not statistically different (p > 0.05) compared with a significant decline (p < 0.05) in phosphorus weight% in lactoferrin subgroups in both DM and PM groups. The enamel surface of lactoferrin subgroups in both DM and PM groups was demineralized and porous, with the enamel of deciduous teeth being more affected by lactoferrin than permanent teeth. CONCLUSION: Lactoferrin suspension decreased the microhardness of enamel and both calcium and phosphorus weight percentages. Both dentitions exhibited erosions in the enamel surface, with primary teeth being more affected than the permanent teeth.

Incorporation of bioactive glass-ceramic into coconut oil for remineralization of incipient carious lesions.

This study evaluated the efficacy of incorporating different concentrations of bioactive glass-ceramic (Biosilicate) into coconut oil on the remineralizing potential and surface roughness of white spot lesions. Fragments (6 x 6 x 2mm) of bovine teeth were sectioned and initial microhardness (KHN) and surface roughness (Ra) readings were obtained. The samples were submitted to cariogenic challenge to form white spot lesions and were separated into six groups (n=13): 1) Artificial Saliva (AS); 2) Coconut Oil (CO); 3) CO+2% Biosilicate (CO+2%Bio); 4) CO+5% Biosilicate (CO+5%Bio); 5) 2% Biosilicate Suspension (2% Bio) and 6) 5% Biosilicate Suspension (5% Bio). The treatments for 1 cycle/day were: immersion into the treatments for 5 minutes, rinsing in distilled water, and storage in artificial saliva at 37ºC. After 14 days, KHN and Ra readings were taken. The surface roughness alteration ((Ra) was analyzed (Kruskal-Wallis, Dunn's post-test, p<0.05). CO+2%Bio had higher (p = 0.0013) (Ra followed by CO+5%Bio (p = 0.0244) than AS. The relative KHN and remineralization potential were analyzed (ANOVA, Tukey, p<0.05), and 5% Bio treatment presented a higher relative microhardness than all other groups (p>0.05). The remineralizing potential of all the treatments was similar (p > .05). When Biosilicate was added, the pH of the suspensions increased and the alkaline pH remained during the analysis. Biosilicate suspension is more efficient than the incorporation of particles into coconut oil at white spot lesion treatment. In addition to the benefits that coconut oil and Biosilicate present separately, their association can enhance the remineralizing potential of Biosilicate.

Force degradation of two orthodontic accessories analyzed in vivo and in vitro.

OBJECTIVE: To compare force degradation of elastomeric chains and NiTi coil springs in vivo and in vitro, and evaluate the effects of pre-stretched and reused elastomeric chains in the oral cavity during the time. METHODS: In the in vitro groups, 4-unit elastomeric chains and NiTi coil springs with an initial force of 200 g were placed in dry air and artificial saliva. The volunteers wore clear retainers which were used to hold the sample of 4-unit chains, pre-stretched 4-unit chains, and NiTi coil springs with the initial force of 200 g in the in vivo groups. After the first 4 weeks, 4-unit specimens were stretched to 200 g again for another 4 weeks in vivo. The force value and the percentage of force degradation were recorded at each measurement time interval in the in vivo and in vitro groups. RESULTS: The force degradation of elastomeric chains was greatest within the initial 4 hours, followed by a more stable phase after 1 week. The average force degradation of 4-unit elastomeric chains after 4 weeks was in vivo (64.8%) > artificial saliva (55.0%) > dry air (46.42%) (P < 0.05). The force degradation of NiTi coil springs in vivo (15.36%) or in artificial saliva (15.8%) was greater than in dry air (7.6%) (P < 0.05). NiTi coil springs presented a gentler force decay than elastomeric chains during the period (P < 0.05). In vivo, the force degradation of pre-stretched and reused elastomeric chains decreased less than the regular style(P < 0.05). CONCLUSION: The force degradation of the elastomeric chains and NiTi coil springs varied in different environments. NiTi coil springs presented a gentler force decay than elastomeric chains during the period. Orthodontists should consider the force degradation characteristics of orthodontic accessories in clinical practice.

Supplementation of Energy Drinks with Green Tea Extract: Effect on In Vitro Abrasive/Erosive Dentin Wear.

PURPOSE: To investigate the effect of the supplementation of energy drinks with green tea extract on abrasive and erosive dentin wear. MATERIALS AND METHODS: Six groups, each comprising 15 bovine dentin samples, were prepared, yielding a total of 90 samples. Erosion was performed by immersing the samples in Red Bull and Red Bull light with and without green tea extract. Tap water with and without green tea extract was used as the control groups. The samples were subjected to abrasive/erosive cycling for five days. The following cycling was performed daily: toothbrush abrasion (20 brushstrokes; 2.5 N); eight erosive cycles (2 min storage in the respective solutions); in between the erosive cycles, storage in artificial saliva (60 min) and again toothbrush abrasion (20 brushstrokes; 2.5 N). During the night, samples were again stored in artificial saliva. Abrasive/erosive dentin wear was measured using a stylus profilometer (µm, accuracy = 40 nm). The measured dentin loss results from the vertical position shift on the y-axis from base to final profile after the wear process in 2D. Pairwise comparisons between the groups were carried out using Wilcoxon signed-rank test. RESULTS: The following dentin wear (median [IQR]) was measured: Red Bull: 1.9 µm (0.5); Red Bull Light: 1.3 µm (0.3); Red Bull with green tea extract: 0.8 µm (0.3); Red Bull Light with green tea extract: 0.3 µm (0.5); Tap water with green tea extract: -0.2 µm (0.7); Tap water: -1.0 µm (1.2). The comparison of all tested groups to each other proved to be statistically significant (p < 0.05). CONCLUSION: The supplementation of energy drinks with green tea extract provide a protective effect against erosive/abrasive wear in vitro.

The Impact of the Addition of Vitamins on a Silicone Lining Material to the Oral Mucosa Tissue-Evaluation of the Biocompatibility, Hydrolytic Stability and Histopathological Effect.

Background and Objectives: One's quality of life depends on overall health, and in particular, oral health, which has been and continues to become a public health issue through frequent manifestations in various forms, from simple oral stomatitis (inflammations of the oral cavity) to the complicated oral health pathologies requiring medical interventions and treatments (caries, pulp necrosis and periodontitis). The aim of this study focused on the preparation and evaluation of vitamins (vitamin A, B1 and B6) incorporated into several silicone-based lining materials as a new alternative to therapeutically loaded materials designed as oral cavity lining materials in prosthodontics. Materials and Methods: Silicone-based liners containing vitamins were prepared by mixing them in solution and becoming crosslinked, and then they were characterized using Fourier-transform infrared (FT-IR) spectroscopy to confirm the incorporation of the vitamins into the silicone network; scanning electron microscopy (SEM) to evidence the morphology of the liner materials; dynamic vapor sorption (DVS) to evaluate their internal hydrophobicity, swelling in environments similar to biological fluids and mechanical test to demonstrate tensile strength; MTT to confirm their biocompatibility on normal cell cultures (fibroblast) and mucoadhesivity; and histopathological tests on porcine oral mucosa to highlight their potential utility as soft lining materials with improved efficiency. Results: FT-IR analysis confirmed the structural peculiarities of the prepared lining materials and the successful incorporation of vitamins into the silicone matrix. The surface roughness of the materials was lower than 0.2 µm, while in cross-section, the lining materials showed a compact morphology. It was found that the presence of vitamins induced a decrease in the main mechanical parameters (strength and elongation at break, Young's modulus) and hydrophobicity, which varied from one vitamin to another. A swelling degree higher than 8% was found in PBS 6.8 (artificial saliva) and water. Hydrolytic stability studies in an artificial saliva medium showed the release of low concentrations of silicone and vitamin fragments in the first 24 h, which increased the swelling behavior of the materials, diffusion and solubility of the vitamins. The microscopic images of fibroblast cells incubated with vitamin liners revealed very good biocompatibility. Also, the silicone liners incorporating the vitamins showed good mucoadhesive properties. The appearance of some pathological disorders with autolysis processes was more pronounced in the case of vitamin A liners. Conclusions: The addition of the vitamins was shown to have a beneficial effect that was mainly manifested as increased biocompatibility, hydrolytic stability and mucoadhesiveness with the mucosa of the oral cavity and less of an effect on the mechanical strength. The obtained lining materials showed good resistance in simulated biological media but caused a pronounced autolysis phenomenon, as revealed by histopathological examination, showing that these materials may have broad implications in the treatment of oral diseases.

Benchmarking of a microgel-reinforced hydrogel-based aqueous lubricant against commercial saliva substitutes.

Xerostomia, the subjective sensation of 'dry mouth' affecting at least 1 in 10 adults, predominantly elders, increases life-threatening infections, adversely impacting nutritional status and quality of life. A patented, microgel-reinforced hydrogel-based aqueous lubricant, prepared using either dairy or plant-based proteins, has been demonstrated to offer substantially enhanced lubricity comparable to real human saliva in in vitro experiments. Herein, we present the benchmarking of in vitro lubrication performance of this aqueous lubricant, both in its dairy and vegan formulation against a range of widely available and employed commercial saliva substitutes, latter classified based on their shear rheology into "liquids", "viscous liquids" and "gels", and also had varying extensional properties. Strikingly, the fabricated dairy-based aqueous lubricant offers up to 41-99% more effective boundary lubrication against liquids and viscous liquids, irrespective of topography of the tested dry mouth-mimicking tribological surfaces. Such high lubricity of the fabricated lubricants might be attributed to their limited real-time desorption (7%) from a dry-mouth mimicking hydrophobic surface unlike the tested commercial products including gels (23-58% desorption). This comprehensive benchmarking study therefore paves the way for employing these microgel-based aqueous lubricant formulations as a novel topical platform for dry mouth therapy.