Quantifying Short-Chain Chlorinated Paraffin Congener Groups.

Accurate quantification of short-chain chlorinated paraffins (SCCPs) poses an exceptional challenge to analytical chemists. SCCPs are complex mixtures of chlorinated alkanes with variable chain length and chlorination level; congeners with a fixed chain length (n) and number of chlorines (m) are referred to as a "congener group" CnClm. Recently, we resolved individual CnClm by mathematically deconvolving soft ionization high-resolution mass spectra of SCCP mixtures. Here we extend the method to quantifying CnClm by introducing CnClm specific response factors (RFs) that are calculated from 17 SCCP chain-length standards with a single carbon chain length and variable chlorination level. The signal pattern of each standard is measured on APCI-QTOF-MS. RFs of each CnClm are obtained by pairwise optimization of the normal distribution's fit to the signal patterns of the 17 chain-length standards. The method was verified by quantifying SCCP technical mixtures and spiked environmental samples with accuracies of 82-123% and 76-109%, respectively. The absolute differences between calculated and manufacturer-reported chlorination degrees were -0.9 to 1.0%Cl for SCCP mixtures of 49-71%Cl. The quantification method has been replicated with ECNI magnetic sector MS and ECNI-Q-Orbitrap-MS. CnClm concentrations determined with the three instruments were highly correlated (R2 > 0.90) with each other.

Deconvolution of Soft Ionization Mass Spectra of Chlorinated Paraffins To Resolve Congener Groups.

We describe and illustrate a three-step data-processing approach that enables individual congener groups of chlorinated paraffins (CPs) to be resolved in mass spectra obtained from either of two soft ionization methods: electron capture negative ionization mass spectrometry (ECNI-MS) or atmospheric pressure chemical ionization mass spectrometry (APCI-MS). In the first step, general fragmentation pathways of CPs are deduced from analysis of mass spectra of individual CP congeners. In the second step, all possible fragment ions in the general fragmentation pathways of CPs with 10 to 20 carbon atoms are enumerated and compared to mass spectra of CP mixture standards, and a deconvolution algorithm is applied to identify fragment ions that are actually observed. In the third step, isotope permutations of the observed fragment ions are calculated and used to identify isobaric overlaps, so that mass intensities of individual CP congener groups can be deconvolved from the unresolved isobaric ion signal intensities in mass spectra. For a specific instrument, the three steps only need to be done once to enable deconvolution of CPs in unknown samples. This approach enables congener group-level resolution of CP mixtures in environmental samples, and it opens up the possibility for quantification of congener groups.

Evidence for New Light-Independent Pathways for Generation of the Endogenous Aryl Hydrocarbon Receptor Agonist FICZ.

Activation of the aryl hydrocarbon receptor (AhR), a conserved transcription factor best known as a target for highly toxic halogenated substances such as dioxin, under normal xenobiotic-free conditions is of considerable scientific interest. We have demonstrated previously that a photoproduct of tryptophan, 6-formylindolo[3,2-b]carbazole (FICZ), fulfills the criteria for an endogenous ligand for this receptor and proposed that this compound is the enigmatic mediator of the physiological functions of AhR. Here, we describe novel light-independent pathways by which FICZ can be formed. The oxidant H2O2 was shown to convert tryptophan to FICZ on its own in the absence of light. The enzymatic deamination of tryptamine yielded indole-3-acetaldehyde (I3A), which then rearranged to FICZ and its oxidation product, indolo[3,2-b]carbazole-6-carboxylic acid (CICZ). Indole-3-pyruvate (I3P) also produced I3A, FICZ, and CICZ. Malassezia yeast species, which constitute a part of the normal skin microbiota, produce a number of AhR activators from tryptophan. We identified both FICZ and CICZ among those products. Formation of FICZ from tryptophan or I3P produces a complex mixture of indole derivatives, some of which are CYP1A1 inhibitors. These can hinder the cellular clearance of FICZ and thereby increase its power as an AhR agonist. We present a general molecular mechanism involving dehydrogenations and oxidative coupling for the formation of FICZ in which I3A is the important precursor. In conclusion, our results suggest that FICZ is likely to be formed systemically.

Fast quantification of chlorinated paraffins in environmental samples by direct injection high-resolution mass spectrometry with pattern deconvolution.

Chlorinated paraffins (CPs) are high production volume chemicals, but data about their environmental fate are scarce. CP mixtures composed of thousands of isomers represent a major challenge for quantification at low levels in environmental samples. Here, we present a novel analytical method for analysis of short-chain, medium-chain, and long-chain CPs in a single injection, that also yields information about congener group pattern. Our detection method is based on direct injection into an atmospheric pressure chemical ionization source operated in negative ion mode under chlorine-enhanced conditions, followed by quadrupole time-of-flight high-resolution mass spectrometry (APCI-qTOF-HRMS) operated in full-scan mode. A mathematical algorithm is applied to deconvolute the CP patterns in the analyzed samples into a linear combination of patterns of technical CP mixtures and to quantify CPs using technical mixtures as external calibration standards. For CP mixtures with known composition, the new method provided concentrations that were within a factor of 1.2 of the target value. Accuracies for CPs spiked to sediment and fish extracts were between 91% and 123%. Concentrations determined in unspiked field samples were within a factor of 5 for short-chain CPs and a factor of 16 for medium-chain CPs of results obtained with an independent method based on gas chromatography/electron capture negative ionization high-resolution mass spectrometry (GC/ECNI-HRMS). The presented APCI-qTOF-HRMS pattern deconvolution method is an interesting alternative for CP analysis in environmental samples. It is particularly sensitive for medium- and long-chain CPs and has the advantage of being extremely fast (instrumental analysis time, less than 1 min).

Using model-based screening to help discover unknown environmental contaminants.

Of the tens of thousands of chemicals in use, only a small fraction have been analyzed in environmental samples. To effectively identify environmental contaminants, methods to prioritize chemicals for analytical method development are required. We used a high-throughput model of chemical emissions, fate, and bioaccumulation to identify chemicals likely to have high concentrations in specific environmental media, and we prioritized these for target analysis. This model-based screening was applied to 215 organosilicon chemicals culled from industrial chemical production statistics. The model-based screening prioritized several recognized organosilicon contaminants and generated hypotheses leading to the selection of three chemicals that have not previously been identified as potential environmental contaminants for target analysis. Trace analytical methods were developed, and the chemicals were analyzed in air, sewage sludge, and sediment. All three substances were found to be environmental contaminants. Phenyl-tris(trimethylsiloxy)silane was present in all samples analyzed, with concentrations of ∼50 pg m(-3) in Stockholm air and ∼0.5 ng g(-1) dw in sediment from the Stockholm archipelago. Tris(trifluoropropyl)trimethyl-cyclotrisiloxane and tetrakis(trifluoropropyl)tetramethyl-cyclotetrasiloxane were found in sediments from Lake Mjøsa at ∼1 ng g(-1) dw. The discovery of three novel environmental contaminants shows that models can be useful for prioritizing chemicals for exploratory assessment.

Conditions for sample preparation and quantitative HPLC/MS-MS analysis of bulky adducts to serum albumin with diolepoxides of polycyclic aromatic hydrocarbons as models.

Stable adducts to serum albumin (SA) from electrophilic and genotoxic compounds/metabolites can be used as biomarkers for quantification of the corresponding in vivo dose. In the present study, conditions for specific analysis of stable adducts to SA formed from carcinogenic polycyclic aromatic hydrocarbons (PAH) were evaluated in order to achieve a sensitive and reproducible quantitative method. Bulky adducts from diolepoxides (DE) of PAH, primarily DE of benzo[a]pyrene (BPDE) and also DE of dibenzo[a,l]pyrene (DBPDE) and dibenzo[a,h]anthracene (DBADE), were used as model compounds. The alkylated peptides obtained after enzymatic hydrolysis of human SA modified with the different PAHDE were principally PAHDE-His-Pro, PAHDE-His-Pro-Tyr and PAHDE-Lys. Alkaline hydrolysis under optimised conditions gave the BPDE-His as the single analyte of alkylated His, but also indicated degradation of this adduct. It was not possible to obtain the BPDE-His as one analyte from BPDE-alkylated SA through modifications of the enzymatic hydrolysis. The BPDE-His adduct was shown to be stable during the weak acidic conditions used in the isolation of SA. Enrichment by HPLC or SPE, but not butanol extraction, gave good recovery, using Protein LoBind tubes. A simple internal standard (IS) approach using SA modified with other PAHDE as IS was shown to be applicable. A robust analytical procedure based on digestion with pronase, enrichment by HPLC or SPE, and analysis with HPLC/MS-MS electrospray ionisation was achieved. A good reproducibility (coefficient of variation (CV) 11 %) was obtained, and the achieved limit of detection for the studied PAHDE, using standard instrumentation, was approximately 1 fmol adduct/mg SA analysing extract from 5 mg SA.

Determination of perfluoroalkyl carboxylic, sulfonic, and phosphonic acids in food.

A sensitive and accurate method was developed and validated for simultaneous analysis of perfluoroalkyl carboxylic acids, sulfonic acids, and phosphonic acids (PFPAs) at low picograms per gram concentrations in a variety of food matrices. The method employed extraction with acetonitrile/water and cleanup on a mixed-mode co-polymeric sorbent (C8 + quaternary amine) using solid-phase extraction. High-performance liquid chromatographic separation was achieved on a C18 column using a mobile phase gradient containing 5 mM 1-methyl piperidine for optimal chromatographic resolution of PFPAs. A quadrupole time-of-flight high-resolution mass spectrometer operating in negative ion mode was used as detector. Method detection limits were in the range of 0.002 to 0.02 ng g(-1) for all analytes. Sample preparation (extraction and cleanup) recoveries at a spiking level of 0.1 ng g(-1) to a baby food composite were in the range of 59 to 98 %. A strong matrix effect was observed in the analysis of PFPAs in food extracts, which was tentatively assigned to sorption of PFPAs to the injection vial in the solvent-based calibration standard. The method was successfully applied to a range of different food matrices including duplicate diet samples, vegetables, meat, and fish samples.

Inhibition of cytochrome P4501-dependent clearance of the endogenous agonist FICZ as a mechanism for activation of the aryl hydrocarbon receptor.

Altered systemic levels of 6-formylindolo[3,2-b]carbazole (FICZ), an enigmatic endogenous ligand for the aryl hydrocarbon receptor (AHR), may explain adverse physiological responses evoked by small natural and anthropogenic molecules as well as by oxidative stress and light. We demonstrate here that several different chemical compounds can inhibit the metabolism of FICZ, thereby disrupting the autoregulatory feedback control of cytochrome P4501 systems and other proteins whose expression is regulated by AHR. FICZ is both the most tightly bound endogenous agonist for the AHR and an ideal substrate for cytochrome CYP1A1/1A2 and 1B1, thereby also participating in an autoregulatory loop that keeps its own steady-state concentration low. At very low concentrations FICZ influences circadian rhythms, responses to UV light, homeostasis associated with pro- and anti-inflammatory processes, and genomic stability. Here, we demonstrate that, if its metabolic clearance is compromised, femtomolar background levels of this compound in cell-culture medium are sufficient to up-regulate CYP1A1 mRNA and enzyme activity. The oxidants UVB irradiation and hydrogen peroxide and the model AHR antagonist 3'-methoxy-4'-nitroflavone all inhibited induction of CYP1A1 enzyme activity by FICZ or 2,3,7,8-tetrachlorodibenzo-p-dioxin, thereby subsequently elevating intracellular levels of FICZ and activating AHR. Taken together, these findings support an indirect mechanism of AHR activation, indicating that AHR activation by molecules with low affinity actually may reflect inhibition of FICZ metabolism and raising questions about the reported promiscuity of the AHR. Accordingly, we propose that prolonged induction of AHR activity through inhibition of CYP1 disturbs feedback regulation of FICZ levels, with potential detrimental consequences.

Simultaneous determination of perfluoroalkyl phosphonates, carboxylates, and sulfonates in drinking water.

A trace analytical method based on high performance liquid chromatography coupled to quadrupole time-of-flight high resolution mass spectrometry was developed for simultaneous determination of perfluoroalkyl phosphonates (PFPAs, carbon chain lengths C6,8,10), perfluoroalkyl carboxylates (PFCAs, C5-12), and perfluoroalkyl sulfonates (PFSAs, C4,6,8,10) in drinking water (tap water). Analytes were enriched on a mixed mode co-polymeric sorbent (C8+quaternary amine) using solid phase extraction. Chromatographic separation was achieved on a Zorbax Extend C18 reversed phase column using a mobile phase gradient consisting of water, methanol, and acetonitrile containing 2mM ammonium acetate and 5 mM 1-methyl piperidine. The mass spectrometer was operated in electrospray negative ion mode. Use of 1-methyl piperidine in the mobile phase resulted in a significant increase in instrument sensitivity for PFPAs through improved chromatographic resolution, background suppression, and increased ionization efficiency. Method detection limits for extraction of 500 mL tap water were in the ranges of 0.095-0.17 ng/L, 0.027-0.17 ng/L, and 0.014-0.052 ng/L for PFPAs, PFCAs, and PFSAs, respectively. Whole method recoveries at a spiking level of 0.5 ng/L to 500 mL HPLC grade water were 40-56%, 56-97%, and 55-77% for PFPAs, PFCAs, and PFSAs, respectively. A matrix effect (signal enhancement) was observed in the detection of PFPAs in tap water extracts, leading to calculated recoveries of 249-297% at a 0.5 ng/L spiking level. This effect resulted in an additional improvement of method sensitivity for PFPAs. To compensate for the matrix effect, PFPAs in tap water were quantified using matrix-matched and extracted calibration standards. The method was successfully applied to the analysis of drinking water collected from six European countries. PFPAs were not detected except for perfluorooctyl phosphonate (PFOPA) at close to the detection limit of 0.095 ng/L in two water samples from Amsterdam, the Netherlands. Highest levels were found for perfluorobutane sulfonate (PFBS, 18.8 ng/L) and perfluorooctanoate (PFOA, 8.6 ng/L) in samples from Amsterdam as well as for perfluorooctane sulfonate (PFOS, 8.8 ng/L) in tap water from Stockholm, Sweden.

Application of a novel solid-phase-extraction sampler and ultra-performance liquid chromatography quadrupole-time-of-flight mass spectrometry for determination of pharmaceutical residues in surface sea water.

In the present study, a multi-residue method based on a bag-solid phase extraction (bag-SPE) technique was evaluated for determination of 10 pharmaceuticals in surface water close to the effluent of a sewage treatment plant (STP) and along a coastal gradient from a STP effluent. The 10 compounds selected were caffeine, atenolol, metoprolol, oxazepam, carbamazepine, ketoprofen, naproxen, ibuprofen, diclofenac and gemfibrozil. All analyses were performed using ultra-performance liquid chromatography (UPLC) combined with quadrupole time-of-flight (QTOF) mass spectrometry. The detection limits (LOD) ranged from 1.0 to 13 ng L(-1). The method showed linear concentration ranges from 25 to 800 ng L(-1) with regression coefficients (R(2)) better than 0.9801. The recoveries of the selected analytes ranged from 11 to 65% with relative standard deviations (RSD) of <16% and inter-day variations of less than 18%. Isotopically labeled surrogate standards were used to compensate for sampling losses and matrix effects. Four of the selected 10 pharmaceuticals (caffeine, metoprolol, oxazepam and carbamazepine) were quantified, at concentrations ranging from 4 to 210 ng L(-1).

Characterization of additional sewage treatment technologies: ecotoxicological effects and levels of selected pharmaceuticals, hormones and endocrine disruptors.

In the present study, two conventional (with and without sand filter) and four additional (moving bed biofilm reactor, ozone, moving bed biofilm reactor combined with ozone and a membrane bio reactor) treatment technologies were operated in small-scale at Hammarby Sjöstad sewage treatment plant, Stockholm, Sweden. The effluents were tested with five short-term (≤ 7 days exposure) ecotoxicological tests, and analyzed for a number of target analytes, comprising pharmaceuticals, natural hormones and industrial chemicals. Overall, the tested effluents generated few adverse effects at lower concentrations (< 50% sewage effluent), and no major differences were observed between any of the treatments. The effluent treated with the moving bed biofilm reactor resulted in the lowest effects in the ecotoxicological tests. The most efficient treatment technology with regard to the pharmaceutical residues was the ozone treatment, which however caused negative effects in some of the ecotoxicological tests.

Evaluation of poly(ethylene-co-vinyl acetate-co-carbon monoxide) and polydimethylsiloxane for equilibrium sampling of polar organic contaminants in water.

The aim of the present study was to develop a passive absorptive equilibrium sampler that would enable the determination of the concentrations of polar organic compound (POC) in water more efficiently than existing techniques. To this end, a novel plastic material, poly(ethylene-co-vinyl acetate-co-carbon monoxide) (PEVAC), was evaluated and the results were compared with an existing silicone-based passive absorptive equilibrium device. Seven compounds (imidacloprid, carbendazim, metoprolol, atrazin, carbamazepine, diazinon, and chlorpyrifos), a mixture of pharmaceuticals, and pesticides with a logarithmic octanol-water partition coefficient ranging from 0.2 to 4.77 were selected as model substances for the experiments. The results showed that six of the seven selected POCs reached distribution equilibrium within 4 d in the two materials tested. A linear relation with a regression coefficient of more than 0.8906 between the established logarithmic absorbent-water partition coefficient and the calculated logarithmic dissociation partition coefficient of the selected compounds in the two polymers was observed. The correlation between these two coefficients was within one order of magnitude for the compounds that reached equilibrium in the two polymers, which demonstrates that both materials are suitable for mimicking biological uptake of POCs. The PEVAC material showed an enhanced sorption for all selected compounds compared to the silicone material and up to five times higher enrichment for the most polar compound. Fluorescence analysis of the sampler cross-section, following the uptake of fluoranthene, and proof that the sorption was independent of surface area variations demonstrated that the PEVAC polymer possessed absorptive rather than adsorptive enrichment of organic compounds.

The ability of a novel sorptive polymer to determine the freely dissolved fraction of polar organic compounds in the presence of fulvic acid or sediment.

A novel plastic material, poly(ethylene-co-vinyl acetate-co-carbon monoxide) (PEVAC), was evaluated as an absorptive passive equilibrium sampler for determination of the freely dissolved fraction of seven polar organic contaminants (POCs) in the presence of fulvic acid and sediment. The seven compounds selected were imidacloprid, carbendazim, metoprolol, atrazin, carbamazepine, diazinon and chlorpyrifos, i.e. a mixture of pharmaceuticals and pesticides having logarithmic octanol/water partition coefficients (log K(OW)) ranging from 0.2 to 4.77. The experiments demonstrated that the PEVAC sampler is well suited for determination of the freely dissolved fraction of chemicals in aquatic environments. Generally, the freely dissolved fraction of the POCs decreased with increasing hydrophobicity. However, strong interactions with functional groups of the organic matter seemed to dominate the partitioning for imidacloprid and carbendazim, having logarithmic dissociation partition coefficient log D < 1.47, and for metoprolol, which is positively charged at neutral pH.

Serial mixed-mode cation- and anion-exchange solid-phase extraction for separation of basic, neutral and acidic pharmaceuticals in wastewater and analysis by high-performance liquid chromatography-quadrupole time-of-flight mass spectrometry.

A novel solid-phase extraction (SPE) method is presented whereby 15 basic, neutral and acidic pharmaceuticals in wastewater were simultaneously extracted and subsequently separated into different fractions. This was achieved using mixed-mode cation- and anion-exchange SPE (Oasis MCX and MAX) in series. Analysis was performed by high-performance liquid chromatography-quadrupole time-of-flight mass spectrometry (HPLC/QTOF-MS). A fast separation was achieved, with all compounds eluting within 6min, narrow chromatographic peaks, with a peak base width of 6s on average, and a high mass accuracy of quantified wastewater sample ions, with average mass errors in absolute value of 0.7mDa or 2.7ppm. The recovery of the SPE method in the analysis of sewage treatment plant (STP) influent and effluent wastewater was on average 80% and the ion suppression 30%. For less demanding samples Oasis MCX used alone may be an alternative method, although for STP influent waters containing high loads of organic compounds the clean-up achieved using only Oasis MCX was insufficient, leading to unreliable quantitation. Furthermore, serial SPE separation according to molecular charge added an additional degree of analyte confirmation. For quantitation, an approach combining external standard calibration curves, isotopically labelled surrogate standards and single-point standard addition was used. The applicability of the method was demonstrated in the analysis of influent and effluent wastewater from an STP, using small sample volumes (25-50mL). The effluent wastewater had been subjected to three different treatments; activated sludge, activated sludge followed by ozonation, and a membrane bioreactor (MBR). Ozone treatment proved superior in removal of the analysed pharmaceuticals, while the MBR provided higher removal efficiencies than the activated sludge process.

Transformations of dissolved organic matter in a landfill leachate--a size exclusion chromatography/mass spectrometric approach.

The aim of the present study was to search for qualitative changes in the landfill leachate DOM along a groundwater gradient. The study was focused on DOM characteristics of importance for its interaction with pollutants, such as molecular weight distribution and aromaticity. It was concluded that the leachate DOM underwent substantial qualitative changes along the investigated gradient at the Vejen landfill, Denmark. The molecular weight decreased, the polydispersity increased, and the aromaticity varied with the lowest values found in the middle of the gradient. The high aromaticity in the end of the gradient may explain the higher DOM binding capacity towards hydrophobic compounds seen earlier in these samples. The relative abundance of ions with mass to charge ratio (m/z) of 600-1200 seemed to be very stable along the gradient, indicating that the observed qualitative changes of the DOM is mostly attributed to changes in the m/z 100-600 range. The DOM seemed to become more similar to fulvic acids present in uncontaminated groundwater with respect to molecular weight and polydispersity along the gradient.

Contribution of biomass burning to atmospheric polycyclic aromatic hydrocarbons at three European background sites.

Radiocarbon analysis of atmospheric polycyclic aromatic hydrocarbons (PAHs) from three background areas in Sweden, Croatia, and Greece was performed to apportion their origin between fossil and biomass combustion. Diagnostic ratios of PAHs implied that wood and coal combustion was relatively more important in the northern European site, while combustion of fossil fuels was the dominant source of PAHs to the two central-southern European background sites. The radiocarbon content (delta14C) of atmospheric PAHs in Sweden ranged between -388 per thousand and -381 per thousand, while more depleted values were observed for Greece (-914 per thousand) and Croatia (-888 per thousand). Using a 14C isotopic mass balance model it was calculated that biomass burning contributes nearly 10% of the total PAH burden in the studied southern European atmosphere with fossil fuel combustion making up the 90% balance. In contrast, biomass burning contributes about 50% of total PAHs in the atmosphere at the Swedish site. Our results suggest that the relative contributions of biomass burning and fossil fuels to atmospheric PAHs may differ considerably between countries, and therefore, different national control strategies might be needed if a further reduction of these pollutants is to be achieved on a continental-global scale.

Airborne PCB as a contamination risk on freeze-drying of sediment.

In a study of polychlorinated biphenyls (PCB) in freeze-dried sediments from Swedish lakes, the samples were found to contain unexpectedly high concentrations of PCBs. In one of the lakes (Björken), e.g. the concentration of PCB-28 was found to be 189 ng/g dw after freeze-drying compared to 7 ng/g dw after air-drying of the sediment and therefore our hypothesis was that the contamination had occurred during the freeze-drying procedure. Hence, a dry reference sediment (RS) was used in order to identify potential sources of PCB contamination. The investigation included freeze-drying of the dry RS in five different laboratories, exposure to the air in the freeze-drying room, storage at room temperature and air-drying in a certain fume hood and in a laminar flow clean bench. The pattern and concentrations of PCBs detected in the exposed RS were strongly influenced by low chlorinated PCB congeners under all of these conditions with exception for air-drying in the fume hood. Storage in the laboratory air resulted in a slight elevation in the concentrations of low chlorinated PCB congeners, whereas higher concentrations of all PCB congeners were observed after freeze-drying. In all experiments the contamination appeared to be due to adsorption of PCB from the laboratory air. On the basis of these findings we recommend that reference material be subjected to the entire procedure, including sample preparation, in order to monitor contamination and that a procedure involving solvent extraction of wet sediment samples is used, whenever possible, instead of procedures involving dry samples.

Characterization of alkyl-cobalamins formed on trapping of epoxide metabolites of 1,3-butadiene.

Analytical methods facilitating studies of electrophilically reactive and genotoxic compounds in vitro and in vivo are needed. The strong nucleophile, cob(I)alamin, formed by reduction of Vitamin B12 [cob(III)alamin], may be used for trapping and analysis of 1,2-epoxides and other electrophiles. In the present study, cob(I)alamin is evaluated as an analytical tool for 1,2-epoxide metabolites (oxiranes) of 1,3-butadiene. Products of reaction of cob(I)alamin with 1,2-epoxy-3-butene (EB), 1,2:3,4-diepoxybutane (DEB), and 1,2-epoxy-3,4-butanediol (EBdiol) have been analyzed by reversed phase high performance liquid chromatography (HPLC) coupled on-line to electrospray ionization mass spectrometry (ESI-MS) and ultraviolet diode array detection (UV-DAD). It was shown that a specific alkyl-CbI complex is formed for each metabolite and that it was possible to discriminate between the products by HPLC-UV and by LC-MS. Quantification of DEB with the method by use of another 1,2-epoxide as an internal standard was successfully performed. The possibility of using cob(I)alamin for trapping and analysis of the three oxirane metabolites of 1,3-butadiene will facilitate quantitative comparisons of species in vitro with regard to metabolism of 1,3-butadiene.

Characterization of in vitro metabolites of the aryl hydrocarbon receptor ligand 6-formylindolo[3,2-b]carbazole by liquid chromatography-mass spectrometry and NMR.

The tryptophan photoproduct 6-formylindolo[3,2-b]carbazole (FICZ) exhibits the highest aryl hydrocarbon receptor (AhR) binding affinity reported so far. In different cells, in vitro, both extracts of UV-irradiated tryptophan and the synthesized pure compound FICZ induce a rapid and transient expression of AhR-regulated genes. The transient induction suggests that the biotransformation gene battery induced by AhR activation takes part in a metabolic degradation of the ligand, whereby a low steady-state level is regained. The down-regulation of AhR-regulated gene expression was previously shown to be dependent on cytochrome P450 1A1 (CYP1A1). Metabolism of FICZ generates five major metabolites, which appeared as three peaks (M1-M3) in the high performance liquid chromatography. The aim of the present study was to use rat liver S9 from Aroclor-pretreated rats to produce large enough quantities of FICZ metabolites for structure characterization and to determine their product precursor relationship. NMR analysis of large combined fractions of the metabolites indicated that M3 and M2 contained 2 isomers, respectively. By means of liquid chromatography-mass spectrometry (negative ion electrospray mode) and NMR spectroscopy (by (1)H-NMR, correlation spectroscopy, and nuclear Overhauser effect spectroscopy techniques) five metabolites of FICZ were identified, and their structures were elucidated. The molecular weights of the two M3 isomers were 300 and both M2 and M1 compounds demonstrated molecular weights of 316, corresponding to addition of one (M3) and of two oxygen (M2 and M1), respectively. The structures were assigned as 2- and 8-hydroxy (M3), 2,10- and 4,8-dihydroxy (M2) and 2,8-dihydroxy derivatives of indolo[3,2-b]carbazole-6-carboxaldehyde (6-formylindolo[3,2-b]carbazole).