Selenium, nickel, and calcium levels in cancerous and non-cancerous prostate tissue samples and their relation with some parameters.

In the present study, tissue samples of patients with cancerous and non-cancerous prostate were analyzed for their Se, Ni, and Ca contents. Possible relationship between Se, Ni, and Ca concentrations and some parameters including preoperative prostate-specific antigen (PSA) levels, histopathological neurovascular invasion, extra-capsular extension, seminal vesicle invasion, positive surgical margins, PSA relapse after radical prostatectomy, and total Gleason scores were obtained. Inductively coupled plasma (ICP) optical emission spectrometry and ICP-mass spectrometry instruments were used for the determination of analytes interested. All the system parameters in digestion and measurement steps were optimized to obtain efficient digestion and sensitive measurements. There was no statistically meaningful difference observed in the concentration of selenium in cancerous and benign prostatic tissues (p = 0.347) while nickel levels in cancerous tissues were observed as significantly lower than benign tissues (p < 0.001). In addition, calcium concentration in cancerous tissue samples were found to be statistically lower than those in benign tissues (p < 0.001) with mean values of 657 and 1,431 mg/kg, respectively.

Lead determination at ng/mL level by flame atomic absorption spectrometry using a tantalum coated slotted quartz tube atom trap.

Flame atomic absorption spectrometry (FAAS) still keeps its importance despite the relatively low sensitivity; because it is a simple and economical technique for determination of metals. In recent years, atom traps have been developed to increase the sensitivity of FAAS. Although the detection limit of FAAS is only at the level of µg/mL, with the use of atom traps it can reach to ng/mL. Slotted quartz tube (SQT) is one of the atom traps used to improve sensitivity. In atom trapping mode of SQT, analyte is trapped on-line in SQT for few minutes using ordinary sample aspiration, followed by the introduction of a small volume of organic solvent to effect the revolatilization and atomization of analyte species resulting in a transient signal. This system is economical, commercially available and easy to use. In this study, a sensitive analytical method was developed for the determination of lead with the help of SQT atom trapping flame atomization (SQT-AT-FAAS). 574 Fold sensitivity enhancement was obtained at a sample suction rate of 3.9 mL/min for 5.0 min trapping period with respect to FAAS. Organic solvent was selected as 40 µL of methyl isobutyl ketone (MIBK). To obtain a further sensitivity enhancement inner surface of SQT was coated with several transition metals. The best sensitivity enhancement, 1650 fold enhancement, was obtained by the Ta-coated SQT-AT-FAAS. In addition, chemical nature of Pb species trapped on quartz and Ta surface, and the chemical nature of Ta on quartz surface were investigated by X-ray photoelectron spectroscopy (XPS) and Raman Spectroscopy. Raman spectrometric results indicate that tantalum is coated on SQT surface in the form of Ta2O5. XPS studies revealed that the oxidation state of Pb in species trapped on both bare and Ta coated SQT surfaces is +2. For the accuracy check, the analyses of standard reference material were performed by use of SCP SCIENCE EnviroMAT Low (EU-L-2) and results for Pb were to be in good agreement with the certified value using SQT-AT-FAAS and Ta coated-SQT.

Tellurium speciation analysis using hydride generation in situ trapping electrothermal atomic absorption spectrometry and ruthenium or palladium modified graphite tubes.

Speciation of tellurium can be achieved by making use of different kinetic behaviors of Te(IV) and Te(VI) upon their reaction with sodium borohydride using hydride generation. While Te(IV) can form H(2)Te, Te(VI) will not form any volatile species during the course of hydride formation and measurement by atomic absorption spectrometry. Quantitative reduction of Te(VI) was achieved through application of a microwave assisted prereduction of Te(VI) in 6.0 mol/L HCl solution. Enhanced sensitivity was achieved by in situ trapping of the generated H(2)Te species in a previously heated graphite furnace whose surface was modified using Pd or Ru. Overall efficiency for in situ trapping in pyrolytically coated graphite tube surface was found to be 15% when volatile analyte species are trapped for 60s at 300°C. LOD and LOQ values were calculated as 0.086 ng/mL and 0.29 ng/mL, respectively. Efficiency was increased to 46% and 36% when Pd and Ru surface modifiers were used, respectively. With Ru modified graphite tube 173-fold enhancement was obtained over 180 s trapping period with respect to ETAAS; the tubes could be used for 250 cycles. LOD values were 0.0064 and 0.0022 ng/mL for Pd and Ru treated ETAAS systems, respectively, for 180 s collection of 9.6 mL sample solution.

Indium determination using slotted quartz tube-atom trap-flame atomic absorption spectrometry and interference studies.

Sensitivity enhancement of indium determination by flame atomic absorption spectrometry (FAAS) was achieved; using a slotted quartz tube (SQT-FAAS) and slotted quartz tube atom trap (SQT-AT-FAAS). SQT was used as an atom trap (AT) where the analyte is accumulated in its inner wall prior to re-atomization. The signal is formed after re-atomization of analyte on the trap surface by introduction of 10 µL of isobutyl methyl ketone (IBMK). Sensitivity was improved 400 times using SQT-AT-FAAS system with respect to conventional FAAS and 279 times with respect to SQT-FAAS without any collection. Characteristic concentration (C(0)) and limit of detection values were found to be 3.63 ng mL(-1) and 2.60 ng mL(-1), respectively, using a sample flow rate of 7.0 mL min(-1) and a collection period of 5.0 min. In addition, interference effects of some elements on indium signal were studied. In order to characterize indium species trapped, X-ray Photoelectron Spectrometry (XPS) was utilized and it was found that indium was collected on the inner surface of SQT as In(2)O(3). The accuracy of the procedure was checked to determine indium in the standard reference material (Montana Soil, SRM 2710).

Prevalence of prostate cancer in high boron-exposed population: a community-based study.

We investigated the possible relationship between boron exposure and prostate cancer (PCa) for men living and being employed at boron mines in villages with rich boron minerals. Out of 456 men studied, 159 were from villages with rich boron sources and boron levels in drinking water of >1 mg L(-1) and these men formed the study group, while 63 from villages with rich boron sources and boron levels in drinking water of <1 mg L(-1) were enrolled into control group 1. A further 234 subjects from other villages with no boron mines were considered as control group 2. Prostate specific antigen (PSA) levels could be obtained from a total of 423 men. Urinary boron concentration as an indicator of boron exposure in 63 subjects, prostatic volumes by transrectal ultrasonography in 39 subjects, and prostatic biopsies in 36 subjects were obtained for study and control groups. The daily boron exposure was calculated according to urinary boron levels. Although there was no significant difference among the groups in terms of total PSA levels, the number of subjects with tPSA ≥2.5 and tPSA ≥10.0 ng dL(-1) prostatic volumes in men whose prostates were biopsied (p < 0.012) was significantly lower in the study group as compared with those in the control group 2. These results suggested that high exposure to boron might have an implication within the prostatic cellular processes related to hyperplasia and carcinogenesis, even though we did not find a statistically significant association between PCa and boron exposure.

Speciation and determination of thiols in biological samples using high performance liquid chromatography-inductively coupled plasma-mass spectrometry and high performance liquid chromatography-Orbitrap MS.

An analytical method was developed for the determination of thiols in biological samples. Reverse phase chromatography coupled to ICP quadrupole MS or Orbitrap MS was employed for the separation and detection of thiols. For the determination of total thiols, oxidized thiols were reduced using dithiothreitol (DTT). Reduction efficiencies for species of interest were found to be close to 100%. Reduced thiols were derivatized by p-hydroxymercuribenzoate (PHMB) and then separated on a C8 column. Optimization of the extraction, separation and detection steps of the HPLC-ICP-MS and HPLC-Orbitrap MS methods was carried out. Detection limits for cysteine, homocysteine, selenocysteine, glutathione, selenomethionine and cysteinyl-glycine were found to be 18, 34, 39, 12, 128 and 103 fmol, respectively, using HPLC-Orbitrap MS and 730, 1110, 440, 1110 and 580 fmol for cysteine, homocysteine, selenocysteine, glutathione, and cysteinyl-glycine using HPLC-ICP-MS. Contrary to expectation, the LODs and RSDs are higher for the HPLC-ICP-MS instrument, therefore HPLC-Orbitrap MS was used for the determination of thiols in yeast samples. Three different brands of baker's yeast and a selenized yeast were analyzed. The GSH and cysteine levels found in these samples ranged from 4.45 to 17.87 µmol g(-1) and 0.61 to 1.32 µmol g(-1), respectively.

Determination and interference studies of bismuth by tungsten trap hydride generation atomic absorption spectrometry.

The determination of bismuth requires sufficiently sensitive procedures for detection at the microg L(-1) level or lower. W-coil was used for on-line trapping of volatile bismuth species using HGAAS (hydride generation atomic absorption spectrometry); atom trapping using a W-coil consists of three steps. Initially BiH(3) gas is formed by hydride generation procedure. The analyte species in vapor form are transported through the W-coil trap held at 289 degrees C where trapping takes place. Following the preconcentration step, the W-coil is heated to 1348 degrees C; analyte species are released and transported to flame-heated quartz atom cell where the atomic signal is formed. In our study, interferences have been investigated in detail during Bi determination by hydride generation, both with and without trap in the same HGAAS system. Interferent/analyte (mass/mass) ratio was kept at 1, 10 and 100. Experiments were designed for carrier solutions having 1.0M HNO(3). Interferents such as Fe, Mn, Zn, Ni, Cu, As, Se, Cd, Pb, Au, Na, Mg, Ca, chloride, sulfate and phosphate were examined. The calibration plot for an 8.0 mL sampling volume was linear between 0.10 microg L(-1) and 10.0 microg L(-1) of Bi. The detection limit (3s/m) was 25 ng L(-1). The enhancement factor for the characteristic concentration (C(o)) was found to be 21 when compared with the regular system without trap, by using peak height values. The validation of the procedure was performed by the analysis of the certified water reference material and the result was found to be in good agreement with the certified values at the 95% confidence level.

Effects of dietary boron on cervical cytopathology and on micronucleus frequency in exfoliated buccal cells.

Recent evidence indicates that boron and borates may have anticarcinogenic properties. In this study, we have investigated the incidence of adverse cytological findings in cervical smears and the micronucleus (MN) frequency in women living in boron-rich and boron-poor regions. Cervical smears were prepared from 1059 women with low socioeconomic status; 472 of the women lived in relatively boron-rich rural areas, while 587 lived in relatively boron-poor regions. The average and standard deviation values for the age of the women screened with the cervical Pap smear test were 41.55 +/- 8.38. The mean dietary intake of boron was 8.41 mg/day for women from the boron-rich regions, and 1.26 mg/day for women living in the boron-poor regions (P < 0.0001). Women from the boron-rich regions had no cytopathological indications of cervical cancer, while there were cytopathological findings for 15 women from the boron-poor areas (chi(2) = 10.473, P < 0.05). Sixty women, 30 from each region, were chosen for evaluating MN frequencies in exfoliated buccal cells. MN frequencies for women from the boron-rich and boron-poor regions were not significantly different (t = -0.294, P > 0.05). Also, there were no significant correlations between age and MN frequency for women from both the boron-rich (r = 0.133, P = 0.48, P > 0.05) and boron-poor (r = -0.033, P = 0.861, P > 0.05) regions. The results suggest that ingestion of boron in the drinking water decreases the incidence of cervical cancer-related histopathological findings. There was no correlation between the pathological findings from the cervical smears and buccal cell MN frequency suggesting that the two study populations were exposed equally to gentotoxic agents. Nonetheless, cervical cancer-related histopathological findings should be validated by other researchers.

Interference effect of iron on the determination of gold in geological samples using the vapor generation technique and preconcentration in a graphite furnace.

A vapor generation procedure for the production of volatile species of Au was studied using electrothermal atomic absorption spectrometry (ETAAS). The interference effects of iron in solution and in the gas phase in a quartz T-tube were studied for the first time in detail. A dual vapor generation system was used for a single heated quartz tube atomizer, so that it was possible to study interferences and classify them regarding their origins. Results show that both gas-phase and liquid-phase interferences are present. It was also concluded that since the total interference effect causes the Au signal to be lower as compared to only the presence of gas-phase interactions in the experiment, the net liquid-phase interference from Fe should be suppressed. The method described in this study was used for the determination of gold in an ore reference material, Carlin Ore Mine, for the purpose of demonstrating the ability of the reported method to determine Au without any extraction procedure.

Flow injection-hydride generation-infrared spectrophotometric determination of Pb.

A novel analytical technique has been suggested for determination of Pb using formation of PbH(4)(g) by chemical reduction and its subsequent spectrophotometric measurement in IR region, using the peak at 1821.4cm(-1). The range of measurements is 1.0-30.0mgl(-1) using a sample of 1.0ml in flow injection mode. The 3sigma limit of detection is 0.28mgl(-1). The method has been applied to standard reference materials of Waste Water, EU-L-1, lead-base bearing metal 53e and Soil/Sediment #4 as well as soil samples collected from heavy traffic areas in Ankara.

Electrothermal atomic absorption spectrometric determination of gold by vapor formation and in situ trapping in graphite tubes.

Gold was determined in ore samples following generation, separation, collection on a graphite cuvette inner wall, and atomization of its volatile species formed by combining an acidified sample solution with an aqueous sodium tetrahydroborate solution at room temperature. A detection limit of 2.6 microg L(-1) (3sigma) was obtained with a 5.0 mL sample volume. Precision of replicate measurements was typically 10% RSD. The overall efficiency of the volatile species generation, transport, and trapping process was 0.4%. Atomization of gold from Pd, Ir, Cu, Ag, and W coated graphite cuvettes, following by trapping of the gaseous volatile gold species on these surfaces, has been investigated. Pd coating was found to decrease the sensitivity. Five microg of Ir, 20 microg of Cu, 20 microg of Ag, and 5 microg of W were chosen as optimum masses. W treatment was the best one for sensitivity enhancement, having an improvement factor of 2.4. Silanization of glass surfaces significantly decreased memory effects; improved peak shapes were thus obtained for flow injection vapor generation atomic absorption spectrometry (FI-VGAAS). The method described in this study was used for the determination of gold in an ore reference material, Gold Ore (MA-1b), Canadian Reference Materials Program.

Selective pre-concentration of selenite from aqueous samples using mercapto-silica.

Silica gel modified with 3-mercaptopropyl-trimethoxysilane was used for the selective separation and pre-concentration of selenite (Se(IV)) from aqueous solutions containing Se(IV) and selenate (Se(VI)). Over a wide range of acidity, from 2 mol l(-1) HCl to pH 9.00, Se(IV) was taken up by the mercaptopropyl-silica with nearly 100% efficiency; Se(VI) however was unretained. Se(IV) content was determined by hydride generation atomic absorption spectrometry (HGAAS), following batch release of the selenium from the pre-concentration medium by acidic periodate. The overall pre-concentration efficiency, including both take-up and elution, in the range of 89-106%. The method was applied to spiked seawater samples containing as low as 800 ng l(-1) Se in selenite form. This solid-phase extraction system offers several major advantages over conventional solvent extraction procedures. It firstly exhibits high selectivity for Se(IV) over Se(VI). Using the solid-phase media, pre-concentration of Se(IV) in dilute water samples can be carried out in the field, stabilizing the selenite-selenium in a convenient form for transport and storage. In addition, selenium stored on silica is derived solely from Se(IV) overcoming problems of selenium redox speciation changes and loss during storage.