RESUMEN
The scientific literature is increasingly focused on peri-implant mucositis and peri-implantitis, which are biological outcomes of dental implant treatment. BACKGROUND/OBJECTIVES: The present study aimed to evaluate the two most critical complications of dental implantation, peri-implant mucositis and peri-implantitis, through the prism of different influencing factors. METHODS: We followed 40 patients, with a total number of 92 dental implants, divided into three age groups: under 35 years, between 35 and 55 years, and older than 55 years. Patients were also divided into groups according to the time since implant placement: 1-3 years, 4-7 years, and more than 7 years. The patients were examined, and periodontal pocket depth, peri-implant pocket depth, Löe-Silness gingival index, mucosal thickness, and keratinized mucosal width were recorded; bone resorption was measured on radiographs using a 2D image analysis method; and a questionnaire was also conducted. RESULTS: Bone resorption was highest in the 35-55 age group (3.09 ± 0.04 mm) and for implants placed 4-7 years ago (3.39 ± 0.12 mm). Females had a mean bone resorption of 3.4 ± 0.15 mm and males of 2.45 ± 0.07 mm. Statistically, there was a significant difference only in the Löe-Silness index: the 35-55 age group had the highest values (p = 0.04). CONCLUSIONS: There were no statistically significant differences between the time since implant placement and the degree of bone resorption, nor between sexes. Peri-implant inflammation may occur at any age, regardless of the lifetime of the implants.
RESUMEN
BACKGROUND: The purpose of this study was to investigate the effect of different light curing modes on the polymerization shrinkage of a bulk-fill composite and to evaluate the impact of two layering techniques on the cuspal deflection. METHODS: Nine different light curing modes were tested on bulk-fill composite samples in aluminum MOD cavities. Intensity, duration, and illumination distance were the factors that changed during the different curing modes. The digital image correlation method was used to visually represent the displacement of carbon particles on the materials' surface caused by shrinkage along both the horizontal and vertical axes. For simulating cuspal deflection, a separate protocol was used, with a bulk and horizontal layering technique. RESULTS: The results showed that the largest horizontal displacements were present in the soft start group (6.00 ± 0.82 µm) and in the X-tra power group (5.67 ± 1.21 µm). The smallest horizontal displacements were detected in normal curing modes (4.00 ± 1.58 µm; 4.00 ± 2.68 µm). The largest vertical displacements, at the bottom layer, were present in the normal curing mode group with a 20 s curing time (5.22 ± 1.56 µm), while the smallest vertical displacements were shown in the X-tra power group (2.89 ± 0.60 µm). The observed particle displacements showing the shrinkage of the composite were correlated with the curing mode. The bulk-fill group showed less cuspal deflection than the horizontal layering group did, but the difference was not statistically significant (p = 0.575). CONCLUSIONS: Within the limitations of this in vitro study, it can be concluded that lower intensities of curing lights (1200 mW/cm2) may perform better from the point of view of material shrinkage than high and extreme light intensities do. The pulse delay mode might be recommended in the case of bulk-fill materials. The number of layers did not significantly affect the cuspal deflection in the case of the studied composite.
RESUMEN
Currently available direct restoration materials have been developed to have improved optical properties to interact with light in the same manner as the natural tooth. The objective of this study was to investigate the fluorescence of different enamel resin composites. In the present study, nine brands of enamel composites were tested in vitro, some of which are cited by manufacturers as having color adjustment potential. Fluorescence spectra of the composite specimens and the human natural enamel were measured with a fluorescence spectrophotometer immediately after preparation and after 6 months. Qualitative data of the specimens were also collected. Statistical analyses were conducted by Kruskal−Wallis and Mann−Whitney U nonparametric tests (p < 0.05). Almost all tested resin composites presented a significant decrease in the fluorescence values after a period of 6 months. There was no significant decrease in fluorescence in the case of Harmonize™ resin composite samples, which presented the lowest initial fluorescence values. The highest value in the reduction of the initial fluorescence intensity after 6 months (22.95%) was observed for the Charisma® specimens. Composites with a color adjustment did not perform significantly better than other composites in terms of reduction in fluorescence intensity.