Pt-Black-Modified (Hemi)spherical AFM Sensors: In Situ Imaging of Light-Driven Hydrogen Peroxide Evolution.

In this work, we present (hemi)spherical atomic force microscopy (AFM) sensors for the detection of hydrogen peroxide. Platinum-black (Pt-B) was electrodeposited onto conductive colloidal AFM probes or directly at recessed microelectrodes located at the end of a tipless cantilever, resulting in electrocatalytically active cantilever-based sensors that have a small geometric area but, due to the porosity of the films, exhibit a large electroactive surface area. Focused ion beam-scanning electron microscopy tomography revealed the porous 3D structure of the deposited Pt-B. Given the accurate positioning capability of AFM, these probes are suitable for local in situ sensing of hydrogen peroxide and at the same time can be used for (electrochemical) force spectroscopy measurements. Detection limits for hydrogen peroxide in the nanomolar range (LOD = 68 ± 7 nM) were obtained. Stability test and first in situ proof-of-principle experiments to achieve the electrochemical imaging of hydrogen peroxide generated at a microelectrode and at photocatalytically active structured poly(heptazine imide) films are demonstrated. Force spectroscopic data of the photocatalyst films were recorded in ambient conditions, in solution, and by applying a potential, which demonstrates the versatility of these novel Pt-B-modified spherical AFM probes.

Optimizing reaction conditions for the light-driven hydrogen evolution in a loop photoreactor.

Photocatalytic hydrogen production from water is a promising way to fulfill energy demands and attain carbon emission reduction goals effectively. In this study, a loop photoreactor with a total volume of around 500 mL is presented for the photocatalytic hydrogen evolution using a Pt-loaded polymeric carbon nitride photocatalyst under 365 nm irradiation in the presence of sacrificial reducing agents. The fluid flow pattern of the developed photoreactor was characterized experimentally and the photon flux incident to the loop photoreactor was measured by chemical actinometry. The system displayed exceptional stability, with operation sustained over 70 hours. A design of experiment (DOE) analysis was used to systematically investigate the influence of key parameters - photon flux, photocatalyst loading, stirring speed, and inert gas flow rate - on the hydrogen generation rate. Linear relationships were found between hydrogen evolution rate and photon flux as well as inert gas flow rate. Photocatalyst loading and stirring speed also showed linear correlations, but could not be correctly described by DOE analysis. Instead, linear single parameter correlations could be applied. Notably, the loop photoreactor demonstrated an external photon efficiency up to 17 times higher than reported in literature studies, while scaling the reactor size by a factor of 10.

Water-soluble ionic carbon nitride as unconventional stabilizer for highly catalytically active ultrafine gold nanoparticles.

Ultrafine metal nanoparticles (NPs) hold promise for applications in many fields, including catalysis. However, ultrasmall NPs are typically prone to aggregation, which often leads to performance losses, such as severe deactivation in catalysis. Conventional stabilization strategies (e.g., immobilization, embedding, or surface modification by capping agents) are typically only partly effective and often lead to loss of catalytic activity. Herein, a novel type of stabilizers based on water-soluble ionic (K+ and Na+ containing) polymeric carbon nitride (i.e., K,Na-poly(heptazine imide) = K,Na-PHI) is reported that enables effective stabilization of highly catalytically active ultrafine (size of ∼2-3 nm) gold NPs. Experimental and theoretical comparative studies using different structural units of K,Na-PHI (i.e., cyanurate, melonate, cyamelurate) indicate that the presence of functionalized heptazine moieties is crucial for the synthesis and stabilization of small Au NPs. The K,Na-PHI-stabilized Au NPs exhibit remarkable dispersibility and outstanding stability even in solutions of high ionic strength, which is ascribed to more effective charge delocalization in the large heptazine units, resulting in more effective electrostatic stabilization of Au NPs. The outstanding catalytic performance of Au NPs stabilized by K,Na-PHI is demonstrated using the selective reduction of 4-nitrophenol to 4-aminophenol by NaBH4 as a model reaction, in which they outperform even the benchmark "naked" Au NPs electrostatically stabilized by excess NaBH4. This work thus establishes ionic carbon nitrides (PHI) as alternative capping agents enabling effective stabilization without compromising surface catalysis, and opens up a route for further developments in utilizing PHI-based stabilizers for the synthesis of high-performance nanocatalysts.

Enhancing Photocatalysis: Understanding the Mechanistic Diversity in Photocatalysts Modified with Single-Atom Catalytic Sites.

Surface modification of heterogeneous photocatalysts with single-atom catalysts (SACs) is an attractive approach for achieving enhanced photocatalytic performance. However, there is limited knowledge of the mechanism of photocatalytic enhancement in SAC-modified photocatalysts, which makes the rational design of high-performance SAC-based photocatalysts challenging. Herein, a series of photocatalysts for the aerobic degradation of pollutants based on anatase TiO2 modified with various low-cost, non-noble SACs (vanadate, Cu, and Fe ions) is reported. The most active SAC-modified photocatalysts outperform TiO2 modified with the corresponding metal oxide nanoparticles and state-of-the-art benchmark photocatalysts such as platinized TiO2 and commercial P25 powders. A combination of in situ electron paramagnetic resonance spectroscopy and theoretical calculations reveal that the best-performing photocatalysts modified with Cu(II) and vanadate SACs exhibit significant differences in the mechanism of activity enhancement, particularly with respect to the rate of oxygen reduction. The superior performance of vanadate SAC-modified TiO2 is found to be related to the shallow character of the SAC-induced intragap states, which allows for both the effective extraction of photogenerated electrons and fast catalytic turnover in the reduction of dioxygen, which translates directly into diminished recombination. These results provide essential guidelines for developing efficient SAC-based photocatalysts.

CVD grown GaSbxN1-x films as visible-light active photoanodes.

The III-V semiconductor GaN is a promising material for photoelectrochemical (PEC) cells, however the large bandgap of 3.45 eV is a considerable hindrance for the absorption of visible light. Therefore, the substitution of small amounts of N anions by isovalent Sb is a promising route to lower the bandgap and thus increase the PEC activity under visible light. Herein we report a new chemical vapor deposition (CVD) process utilizing the precursors bis(N,N'-diisopropyl-2-methyl-amidinato)-methyl gallium (III) and triphenyl antimony (TPSb) for the growth of GaSbxN1-x alloys. X-ray diffraction (XRD) and scanning electron microscopy (SEM) measurements show crystalline and homogeneous thin films at deposition temperatures in the range of 500-800 °C. Rutherford backscattering spectrometry (RBS) combined with nuclear reaction analysis (NRA) shows an incorporation of 0.2-0.7 at% antimony into the alloy, which results in a slight bandgap decrease (up to 0.2 eV) accompanied by enhanced sub-bandgap optical response. While the resulting photoanodes are active under visible light, the external quantum efficiencies remained low. Intriguingly, the best performing films exhibits the lowest charge carrier mobility according to time resolved THz spectroscopy (TRTS) and microwave conductivity (TRMC) measurements, which showed mobilities of up to 1.75 cm2 V-1 s-1 and 1.2 × 10-2 cm2 V-1 s-1, for each timescale, respectively.

Ultrafast anisotropic exciton dynamics in a water-soluble ionic carbon nitride photocatalyst.

Ultrafast transient absorption anisotropy spectroscopy (TAA) reveals the orientational dynamics of light-induced excitations in a water soluble poly(heptazine imide). The results provide insights into the fast charge transfer processes in the material.

A Study in Red: The Overlooked Role of Azo-Moieties in Polymeric Carbon Nitride Photocatalysts with Strongly Extended Optical Absorption.

The unique optical and photoredox properties of heptazine-based polymeric carbon nitride (PCN) materials make them promising semiconductors for driving various productive photocatalytic conversions. However, their typical absorption onset at ca. 430-450 nm is still far from optimum for efficient sunlight harvesting. Despite many reports of successful attempts to extend the light absorption range of PCNs, the determination of the structural features responsible for the red shift of the light absorption edge beyond 450 nm has often been obstructed by the highly disordered structure of PCNs and/or low content of the moieties responsible for changes in optical and electronic properties. In this work, we implement a high-temperature (900 °C) treatment procedure for turning the conventional melamine-derived yellow PCN into a red carbon nitride. This approach preserves the typical PCN structure but incorporates a new functionality that promotes visible light absorption. A detailed characterization of the prepared material reveals that partial heptazine fragmentation accompanied by de-ammonification leads to the formation of azo-groups in the red PCN, a chromophore moiety whose role in shifting the optical absorption edge of PCNs has been overlooked so far. These azo moieties can be activated under visible-light (470 nm) for H2 evolution even without any additional co-catalyst, but are also responsible for enhanced charge-trapping and radiative recombination, as shown by spectroscopic studies.

Anatase-Wrapped Rutile Nanorods as an Effective Electron Collector in Hybrid Photoanodes for Visible Light-Driven Oxygen Evolution.

Arrays of single crystal TiO2 rutile nanorods (RNRs) appear highly promising as electron-collecting substrates in hybrid photoanodes as the RNRs offer direct charge carriers transport pathways, contrary to the conventional electrodes prepared from TiO2 powders that suffer from the numerous charge traps at the grain boundaries. However, the specific surface area of the nanorods is highly limited by their smooth morphology, which might be detrimental in view of utilizing the RNR as a substrate for immobilizing other functional materials. In this study, we developed a novel anatase-wrapped RNR (ARNR) material fabricated by a facile seed layer-free hydrothermal method. The ARNR comprises polycrystalline anatase nanoparticles formed on the surface of RNR, resulting in a large surface area that provides more deposition sites compared to the bare nanorods. Herein, we functionalize ARNR and RNR electrodes with polymeric carbon nitride (CNx) coupled with a CoO(OH)x cocatalyst for dioxygen evolution. The anatase wrapping of the rutile nanorod scaffold is found to be crucial for effective deposition of CNx and for improved photoanode operation in visible light-driven (λ > 420 nm) oxygen evolution, yielding a significant enhancement of photocurrent (by the factor of ∼3.7 at 1.23 V vs. RHE) and faradaic efficiency of oxygen evolution (by the factor of ∼2) as compared to photoanodes without anatase interlayer. This study thus highlights the importance of careful interfacial engineering in constructing photoelectrocatalytic systems for solar energy conversion and paves the way for the use of ARNR-based electron collectors in further hybrid and composite photochemical architectures for solar fuel production.

Photodriven Charge Accumulation and Carrier Dynamics in a Water-Soluble Carbon Nitride Photocatalyst.

Charge accumulation in photoactive molecules and materials holds great promise in solar energy conversion as it allows for decoupling solar-driven charging from (dark) redox reactions. In this contribution, light-driven charge accumulation was investigated for a recently reported novel water-soluble carbon nitride [K,Na-poly(heptazine imide); K,Na-PHI] photocatalyst, which exhibits excellent activity and stability in highly selective photocatalytic oxidation of alcohols and concurrent reduction of dioxygen to H2 O2 under quasi-homogeneous conditions. An excellent charge storage ability of the K,Na-PHI material was demonstrated, showing an optimal density of accumulated electrons (32.2 µmol of electrons per gram) in the presence of 10 vol % MeOH as a sacrificial electron donor. The long-lived electrons accumulated under anaerobic conditions as K,Na-PHI.- radical ions were utilized in interfacial electron transfer to O2 or methyl viologen in a subsequent dark reaction. Ultrafast time-resolved spectroscopy was employed to reveal the kinetics of charge-carrier recombination and methanol oxidation. Geminate recombination of electrons and holes within approximately 100 ps was followed by trap-assisted recombination. The presence of methanol as a sacrificial electron donor accelerated the decay of the transient absorption signal when a static sample was used. This behavior was ascribed to the faster charge recombination in the presence of the radical anions generated after hole extraction. The work suggests that photodriven electron storage in the water-soluble carbon nitride is enabled by localized trap states, and highlights the importance of the effective electron donor for creating long-lived photo-generated carbon nitride radicals.

Sol-Gel Processing of Water-Soluble Carbon Nitride Enables High-Performance Photoanodes*.

In spite of the enormous promise that polymeric carbon nitride (PCN) materials hold for various applications, the fabrication of high-quality, binder-free PCN films and electrodes has been a largely elusive goal to date. Here, we tackle this challenge by devising, for the first time, a water-based sol-gel approach that enables facile preparation of thin films based on poly(heptazine imide) (PHI), a polymer belonging to the PCN family. The sol-gel process capitalizes on the use of a water-soluble PHI precursor that allows formation of a non-covalent hydrogel. The hydrogel can be deposited on conductive substrates, resulting in formation of mechanically stable polymeric thin layers. The resulting photoanodes exhibit unprecedented photoelectrochemical (PEC) performance in alcohol reforming and highly selective (∼100 %) conversions with very high photocurrents (>0.25 mA cm-2 under 2 sun) down to <0 V vs. RHE. This enables even effective PEC operation under zero-bias conditions and represents the very first example of a 'soft matter'-based PEC system capable of bias-free photoreforming. The robust binder-free films derived from sol-gel processing of water-soluble PCN thus constitute a new paradigm for high-performance 'soft matter' photoelectrocatalytic systems and pave the way for further applications in which high-quality PCN films are required.

On the importance of catalysis in photocatalysis: Triggering of photocatalysis at well-defined anatase TiO2 crystals through facet-specific deposition of oxygen reduction cocatalyst.

Well-defined anatase TiO2 crystals with co-exposed {101} and {001} facets represent a promising platform for fundamental studies in photocatalysis and for the development of novel photocatalytic systems exhibiting higher than usual quantum efficiencies. Herein, we present protocols enabling the photoreductive deposition of Pt nanoparticles onto anatase TiO2 micro-sized (1-3 µm) crystals prepared by hydrothermal growth in fluoride-containing solutions to be carried out either facet-selectively (on {101} facets only) or facet-non-selectively (on both {101} and {001} facets). The photocatalytic behavior of the resulting photocatalysts is studied using investigations of oxidative photodegradation of a test pollutant [4-chlorophenol (4-CP)], photocurrent measurements, and kinetic analysis of the open-circuit photopotential decay. We demonstrate that the deposition of Pt nanoparticles effectively triggers the photocatalytic degradation of 4-CP at anatase crystals that are otherwise completely inactive. The role of Pt in triggering the photocatalysis is demonstrated to consist chiefly in the catalytic enhancement of the reaction rate of oxygen reduction by the photogenerated electrons. Only the platinized {101} facets contribute to photocatalysis, whereas the {001} facets, in the literature often referred to as "highly reactive", are even after platinization completely inactive, most likely due to (1 × 4) surface reconstruction upon the heat treatment necessary to decrease the amount of surface fluorides. Based on our results, we highlight the eminent role of efficient surface catalysis for effective charge separation and provide specific design rules for further development of photocatalysts with high quantum efficiencies.

Water-Soluble Polymeric Carbon Nitride Colloidal Nanoparticles for Highly Selective Quasi-Homogeneous Photocatalysis.

Heptazine-based polymeric carbon nitrides (PCN) are promising photocatalysts for light-driven redox transformations. However, their activity is hampered by low surface area resulting in low concentration of accessible active sites. Herein, we report a bottom-up preparation of PCN nanoparticles with a narrow size distribution (ca. 10±3 nm), which are fully soluble in water showing no gelation or precipitation over several months. They allow photocatalysis to be carried out under quasi-homogeneous conditions. The superior performance of water-soluble PCN, compared to conventional solid PCN, is shown in photocatalytic H2 O2 production via reduction of oxygen accompanied by highly selective photooxidation of 4-methoxybenzyl alcohol and benzyl alcohol or lignocellulose-derived feedstock (ethanol, glycerol, glucose). The dissolved photocatalyst can be easily recovered and re-dissolved by simple modulation of the ionic strength of the medium, without any loss of activity and selectivity.

Selectivity of Chemical Conversions: Do Light-Driven Photoelectrocatalytic Processes Hold Special Promise?

One of the great challenges in chemistry is the development of innovative catalytic processes. In this context, significant opportunities are currently opening up for technologies based on electrocatalysis and photoelectrocatalysis, as these can drive various valuable catalytic redox transformations under very mild conditions. However, many catalytic processes lead to various different products of different value, and the technological attractiveness of catalytic processes depends to a large extent on their selectivity towards a specific desired product. In this Viewpoint, I propose and explore the idea that, due to the distinct features of interfacial energetics at illuminated semiconductors, light-driven photoelectrocatalytic processes at well-designed semiconductors represent a particularly attractive platform for the development of highly efficient systems for selective catalytic conversions. The investigations of selectivity and synthetic aspects of photoelectrocatalysis should gain momentum, especially as they also promise commercially viable applications on a more immediate time scale as compared to, for example, the light-driven production of hydrogen.

Controlling the Photocorrosion of Zinc Sulfide Nanoparticles in Water by Doping with Chloride and Cobalt Ions.

Photodegradation under UV light irradiation is a major drawback in photocatalytic applications of sulfide semiconductors. ZnS nanoparticles were doped with very low amounts of chloride or cobalt ions in the ppm range and codoped with chloride and cobalt ions during their synthesis by precipitation in aqueous solution followed by calcination. The high-temperature wurtzite phase annealed at 800 °C had a high susceptibility to UV irradiation in water, while the low-temperature zincblende phase annealed at 400 °C was found to be stable. Chlorine doping increased the rate of photocorrosion in water, whereas cobalt doping led to a stabilization of the ZnS nanoparticles. Based on photochemical and spectroscopic investigations applying UV/vis, X-ray photoelectron, and photoluminescence spectroscopy, the increased susceptibility of Cl-doped ZnS is ascribed to a higher number of surface point defects, whereas the stabilization by Co2+ is caused by additional recombination pathways for the charge carriers in the bulk, thus avoiding photocorrosion processes at the surface. Additional doping of Cl-doped ZnS with cobalt ions was found to counteract the detrimental effect of the chloride ions efficiently.

Carbon nitride-TiO2 hybrid modified with hydrogenase for visible light driven hydrogen production.

A system consisting of a [NiFeSe]-hydrogenase (H2ase) grafted on the surface of a TiO2 nanoparticle modified with polyheptazine carbon nitride polymer, melon (CN x ) is reported. This semi-biological assembly shows a turnover number (TON) of more than 5.8 × 105 mol H2 (mol H2ase)-1 after 72 h in a sacrificial electron donor solution at pH 6 during solar AM 1.5 G irradiation. An external quantum efficiency up to 4.8% for photon-to-hydrogen conversion was achieved under irradiation with monochromatic light. The CN x -TiO2-H2ase construct was also active under UV-free solar light irradiation (λ > 420 nm), where it showed a substantially higher activity than TiO2-H2ase and CN x -H2ase due, in part, to the formation of a CN x -TiO2 charge transfer complex and highly productive electron transfer to the H2ase. The CN x -TiO2-H2ase system sets a new benchmark for photocatalytic H2 production with a H2ase immobilised on a noble- and toxic-metal free light absorber in terms of visible light utilisation and stability.

Surface-Modified TiO2 Photocatalysts Prepared by a Photosynthetic Route: Mechanism, Enhancement, and Limits.

Surface-modified TiO2 photocatalysts were synthesized by a photosynthetic route involving visible-light-induced (λ>455 nm) activation of benzene and toluene at the surface of TiO2 leading to the formation of carbonaceous polymeric deposits. IR spectroscopic and photoelectrochemical experiments showed that the mechanism of the photosynthetic reactions involves intra-bandgap surface states at TiO2 related to surface OH groups interacting with adsorbed aromatic molecules. The photosynthesized surface-modified TiO2 materials exhibited enhanced activity, relative to pristine TiO2 , in photocatalytic degradation (and complete mineralization) of 4-chlorophenol. The improvement was pronounced particularly under visible-light (λ>455 nm) irradiation with the relative initial photodegradation rate enhanced by a factor of four. The surface-modified photocatalysts exhibited good stability under the operating conditions, and the optimum carbon content was approximately 0.5 wt %. Mechanistic studies showed that the enhanced visible-light photodegradation of 4-chlorophenol is due to modified surface-adsorption properties that facilitate formation of a surface complex between titania and 4-chlorophenol, rather than due to any sensitizing effect of the carbonaceous deposits. The study highlights the importance of considering the interaction between pollutant molecules and the photocatalyst surface in heterogeneous photocatalysis, and possibly opens up a route for photosynthesis of further surface-modified photocatalysts with tuned surface properties.

Fast and robust infiltration of functional material inside titania nanotube layers: case study of a chalcogenide glass sensitizer.

Fast and robust infiltration of anodic TiO2 nanotube layers with a model chalcogenide As3S7 glass via spin-coating is reported for the first time. Effective sensitization leads to a significant visible light photocurrent response. This easy and cheap infiltration method can be extended for deposition of other absorbers into nanotubular layers.

Enhanced performance of surface-modified TiO2 photocatalysts prepared via a visible-light photosynthetic route.

Benzene can be activated by visible light (λ > 455 nm) in the presence of TiO(2), which leads to formation of carbonaceous polymeric deposits on the titania surface. These photosynthesized surface-modified materials exhibit enhanced photoactivity in degradation of phenolic compounds, particularly under visible light irradiation.