RESUMEN
Polyester/cotton fabrics with different proportions of Tetron Cotton, TC (35% Cotton/65% PET), and Chief Value Cotton, CVC (60% Cotton/40% PET), were investigated by removing the cotton component under various phosphoric acidic conditions including the use of cellulase enzymes. The remaining polyethylene terephthalate (PET) component was spun using the melt spinning method. Only 85% H3PO4-Enz_TC could be spun into consistent filament fibers. The effects of Acid-Enz TC (obtained from a powder preparation of 85% H3PO4-Enz_TC) at different weight amounts (1, 2, 5, and 10 %wt) blending with WF-rPET powder prepared by white recycled polyester fabric were evaluated for fiber spinnability at different winding speeds of 1000 and 1500 m/min. The results revealed that recycled PET fiber spun by adding Acid-Enz_TC up to 10 %wt gave uniformly distributed filament fibers. A comparative study of the physical, thermal, and mechanical properties also investigated the relationship between the effect of Acid-Enz_TC and the structure of the obtained fibers. Acid-Enz_TC:WF-rPET (5:95) was the optimal ratio. The thermal values were analyzed by DSC and TGA and crystallinity was analyzed by XRD, with mechanical strength closed to 100% WF-rPET. The FTIR analysis of the functional groups showed the removal of cotton from the blended fabrics. Other factors such as the Acid-Enz_TC component in WF-rPET, extraction conditions, purity, thermal, chemical, and exposure experiences also affected the formability and properties of recycled PET made from non-single-component raw materials. This study advanced the understanding of recycling PET from TC fabrics by strategically removing cotton from polyester-cotton blends and then recycling using controlled conditions and processes via the melt spinning method.
RESUMEN
PET knitted fabric was melted and cooled by hot pressing at 250 °C to obtain a compacted sheet. Only white PET fabric (WF_PET) was used to study the recycling process by compression and grinding to powder and then melt spinning at different take-up speeds compared to PET bottle grade (BO_PET). PET knitted fabric had good fiber formability and was better suited for melt spinning of recycled PET (r-PET) fibers than the bottle grade. Thermal and mechanical properties of r-PET fibers improved in terms of crystallinity and tensile strength with increasing take-up speed (500 to 1500 m/min). Fading and color changes from the original fabric were relatively small compared with PET bottle grade. Results indicated that fiber structure and properties can be used as a guideline for improving and developing r-PET fibers from textile waste.
RESUMEN
This paper is aimed at investigating the usage of biosynthesized poly(3-hydroxybutyrate) (P(3-HB)) for a coating on pineapple leaf fiber paper (PLFP). For this purpose, (P(3-HB)) was produced by Rhodococcus pyridinivorans BSRT1-1, a highly potential P(3-HB) producing bacterium, with a weight-average molecular weight (Mw) of 6.07 × 10 -5 g/mol. This biosynthesized P(3-HB) at 7.5% (w/v) was then coated on PLFP through the dip-coating technique with chloroform used as a solvent. The respective coated PLFP showed that P(3-HB) could be well coated all over on the PLFP surface as confirmed by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The brightness and mechanical properties of PLFP could be improved by coating with biosynthesized P(3-HB) in comparison to commercially available P(3-HB) and non-coated PLFP. Furthermore, coating of P(3-HB) significantly increased the water drop penetration time on the surface of PLFP and was similar to that of the commercial P(3-HB) with the same content. The results showed that all the coated PLPF samples can be degraded under the soil burial test conditions. We have demonstrated that the P(3-HB) coated PLFP paper has the ability to prevent water drop penetration and could undergo biodegradation. Taken together, the P(3-HB) coated PLFP can be applied as a promising biodegradable paper packaging.