Recovery of rare earth elements (Nd3+ and Dy3+) by using carbon-based adsorbents from spent tire rubber.

Two samples of spent tire rubber (rubber A and rubber B) were submitted to thermochemical conversion by pyrolysis process. A450, B450 and A900, B900 chars were obtained from rubber A and rubber B at 450 °C and 900 °C, respectively. The chars were then applied as recovery agents of Nd3+ and Dy3+ from aqueous solutions in mono and bicomponent solutions, and their performance was benchmarked with a commercial activated carbon. The chars obtained at 900 °C were the most efficient adsorbents for both elements with uptake capacities around 30 mg g-1. The chars obtained at 450 °C presented uptake capacities similar to the commercial carbon (≈ 11 mg g-1). A900 and B900 chars presented a higher availability of Zn ions that favored the ion exchange mechanism. It was found that Nd3+ and Dy3+ were adsorbed as oxides after Zn was released from silicate structures (Zn2SiO4). A900 char was further selected to be tested with Nd/Dy binary mixtures and it was found a trend to adsorb a slightly higher amount of Dy3+ due to its smaller ionic radius. The uptake capacity in bicomponent solutions was generally higher than for single component solutions due to the higher driving force triggered by the higher concentration gradient.

Simultaneous Synthesis and Nitrogen Doping of Free-Standing Graphene Applying Microwave Plasma.

An experimental and theoretical investigation on microwave plasma-based synthesis of free-standing N-graphene, i.e., nitrogen-doped graphene, was further extended using ethanol and nitrogen gas as precursors. The in situ assembly of N-graphene is a single-step method, based on the introduction of N-containing precursor together with carbon precursor in the reactive microwave plasma environment at atmospheric pressure conditions. A previously developed theoretical model was updated to account for the new reactor geometry and the nitrogen precursor employed. The theoretical predictions of the model are in good agreement with all experimental data and assist in deeper understanding of the complicated physical and chemical process in microwave plasma. Optical Emission Spectroscopy was used to detect the emission of plasma-generated ''building units'' and to determine the gas temperature. The outlet gas was analyzed by Fourier-Transform Infrared Spectroscopy to detect the generated gaseous by-products. The synthesized N-graphene was characterized by Scanning Electron Microscopy, Raman, and X-ray photoelectron spectroscopies.

Electrospun biodegradable chitosan based-poly(urethane urea) scaffolds for soft tissue engineering.

The composition and architecture of a scaffold determine its supportive role in tissue regeneration. In this work, we demonstrate the feasibility of obtaining a porous electrospun fibrous structure from biodegradable polyurethanes (Pus) synthesized using polycaprolactone-diol as soft segment and, as chain extenders, chitosan (CS) and/or dimethylol propionic acid. Fourier transform infrared spectroscopy and proton nuclear magnetic resonance confirmed the syntheses. Fibre mats' properties were analysed and compared with those of solvent cast films. Scanning electron microscopy images of the electrospun scaffolds revealed fibres with diameters around 1 µm. From tensile tests, we found that Young's modulus increases with CS content and is higher for films (2.5 MPa to 6.5 MPa) than for the corresponding fibre mats (0.8 MPa to 3.2 MPa). The use of CS as the only chain extender improves recovery ratio and resilience. From X-ray diffraction, a higher crystalline degree was identified in fibre mats than in the corresponding films. Films' wettability was enhanced by the presence of CS as shown by the decrease of water contact angle. X-ray photoelectron spectroscopy revealed that while ester groups are predominant at the films' surface, ester and urethanes are present in similar concentrations at fibres' surface, favouring the interaction with water molecules. Both films and fibres undergo hydrolytic degradation. In vitro evaluation was performed with human dermal fibroblasts. No PU sample revealed cytotoxicity. Cells adhered to fibre mats better than to films and proliferation was observed only for samples of CS-containing PUs. Results suggest that electrospun fibres of CS-based polyurethanes are good candidate scaffolds for soft tissue engineering.

Large-scale synthesis of free-standing N-doped graphene using microwave plasma.

Direct assembling of N-graphene, i.e. nitrogen doped graphene, in a controllable manner was achieved using microwave plasmas at atmospheric pressure conditions. The synthesis is accomplished via a single step using ethanol and ammonia as carbon and nitrogen precursors. Tailoring of the high-energy density plasma environment results in a selective synthesis of N-graphene (~0.4% doping level) in a narrow range of externally controlled operational conditions, i.e. precursor and background gas fluxes, plasma reactor design and microwave power. Applying infrared (IR) and ultraviolet (UV) irradiation to the flow of free-standing sheets in the post-plasma zone carries out changes in the percentage of sp2, the N doping type and the oxygen functionalities. X-ray photoelectron spectroscopy (XPS) revealed the relative extension of the graphene sheets π-system and the type of nitrogen chemical functions present in the lattice structure. Scanning Electron microscopy (SEM), Transmission Electron microscopy (TEM) and Raman spectroscopy were applied to determine morphological and structural characteristics of the sheets. Optical emission and FT-IR spectroscopy were applied for characterization of the high-energy density plasma environment and outlet gas stream. Electrochemical measurements were also performed to elucidate the electrochemical behavior of NG for supercapacitor applications.

Functionalization of cotton fabrics with plasmonic photo-active nanostructured Au-TiO2 layer.

A simple approach to functionalize cotton fabrics with Au and TiO2 nanostructured layer is presented. Hybrid fabrics (Cot-Au-TiO2) are prepared through reduction of AuCl4- on cotton, followed by a non-aqueous sol-gel procedure using tetrabutyltitanate and a hydrothermal treatment at 110°C. The generation of crystalline TiO2 is confirmed by Raman spectroscopy. The fibres morphology and their roughness are characterized by AFM and FE-SEM. XPS shows how the concentration of the NPs precursors (Au and TiO2) affects the layer composition. GSDR (Ground State Diffuse Reflectance Absorption Spectroscopy) and LIL (Laser induced luminescence) reveal a strong quenching effect induced by Au NPs. Photocatalytic activity measured through the Remazol Blue (RB) degradation reveals an enhancement under visible light, which increases with Au loading. This strong enhancement is explained through the surface plasmon resonance brought by Au NPs.

Controlled growth of Cu2O nanoparticles bound to cotton fibres.

A green, safe and fast procedure is presented for in situ generation of nanoparticles (NPs) of cuprous oxide (Cu2O) onto cotton fibres at room temperature using water as a solvent. The method is based on a mild surface oxidation of cellulose fibres to generate in a controlled way carboxylic groups acting as a binding site for the adsorption of Cu(2+) via electrostatic coordination. Then, the adsorbed Cu(2+) ions were readly converted into Cu2O by dipping the treated cotton fibres into a aqueous solution of a reducing agent. Field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD), as well as UV-vis absorption and emission spectroscopic methods were used to analyse the size, morphology, chemical composition and the crystalline structure of the generated nanoparticles on the fabrics. The morphology of the ensuing Cu2O nanoparticles was shown to be dependent on the reduycing agent used. Antibacterial properties of the modified fibres were also investigated.

Energy Thresholds of DNA Damage Induced by UV Radiation: An XPS Study.

This work stresses on damage at the molecular level caused by ultraviolet radiation (UV) in the range from 3.5 to 8 eV, deoxyribonucleic acid (DNA) films observed by X-ray photoelectron spectroscopy (XPS). Detailed quantitative XPS analysis, in which all the amounts are relative to sodium-assumed not to be released from the samples, of the carbon, oxygen, and particularly, nitrogen components, reveals that irradiation leads to sugar degradation with CO-based compounds release for energies above 6.9 eV and decrease of nitrogen groups which are not involved in hydrogen bonding at energies above 4.2 eV. Also the phosphate groups are seen to decrease to energies above 4.2 eV. Analysis of XPS spectra allowed to conclude that the damage on bases peripheral nitrogen atoms are following the damage on phosphates. It suggests that very low kinetic energy photoelectrons are ejected from the DNA bases, as a result of UV light induced breaking of the phosphate ester groups which forms a transient anion with resonance formation and whereby most of the nitrogen DNA peripheral groups are removed. The degree of ionization of DNA was observed to increase with radiation energy, indicating that the ionized phosphate groups are kept unchanged. This result was interpreted by the shielding of phosphate groups caused by water molecules hydration near sodium atoms.

Pyrene-p-tert-butylcalixarenes inclusion complexes formation: a surface photochemistry study.

Diffuse reflectance and luminescence techniques were used to study the photophysics and photochemistry of pyrene within p-tert-butylcalix[n]arenes with n = 4, 6, and 8, and to study their ability to form inclusion complexes in heterogeneous media. Evidences for inclusion complex formation were found for the three hosts under study. Ground state diffuse reflectance results have shown the formation of ground state dimers of pyrene inside the cavity of calix[6]arene and calix[8]arene, with this feature much more evident for calix[6]arene. For calix[4]arene, only a monomer fits inside the cavity and the presence of pyrene microcrystals outside the cavity was detected. A luminescence lifetime distribution analysis was performed, revealing the presence of prompt emissions from the pyrene microcrystals outside the cavity in the case of calix[4]arene and from the constrained dimers inside the cavities of calix[6]arene and calix[8]arene. Transient absorption results have shown the presence of pyrene radical cation and also of trapped electrons for the three hosts under study. The formation of the phenoxyl radical of the calixarene following the laser pulsed excitation of pyrene at 355 nm is increased for calix[6]arene and calix[8]arene. This feature is particularly relevant for calix[6]arene, suggesting a very favourable situation for the hydrogen atom abstraction to occur. The analysis of the degradation products revealed the presence of hydroxypyrene as a major photodegradation product for the three hosts. Dihydro-hydroxypyrene was also formed in the case of calix[6]arene and calix[8]arene. The formation of the calixarene's phenoxyl radical and subsequent hydrogen abstraction is consistent with the formation of dihydro-dihydroxypyrene.

Adsorption of phenylphosphonic acid on GaAs (100) surfaces.

The adsorption of phenylphosphonic acid (PPA) on GaAs (100) surfaces from solutions in acetonitrile/water mixtures was studied using Fourier transform infrared spectroscopy in attenuated total reflection in multiple internal reflections (ATR/MIR), X-ray photoelectron spectroscopy (XPS), high-resolution electron energy loss spectroscopy (HREELS), and atomic force microscopy (AFM). ATR/MIR in situ showed that the accumulation of PPA molecules near the GaAs surface increased with the water concentration in the solution. For water contents lower than 4%, ATR/MIR and XPS results are consistent with the formation of a low-density monolayer. A mechanism is proposed for H2O percentages lower than 4% involving the creation of interfacial bonds through a Brønsted acid-base reaction, which involves the surface hydroxyl groups most probably bound to Ga. It was found that the morphology of the final layer depended strongly on the water concentration in the adsorbing solution. For water concentrations equal to or higher than 5%, the amount of adsorbed molecules drastically increased and was accompanied by modifications in the infrared spectral region corresponding to P-O and P=O. This sudden change indicates a deprotonation of the acid. XPS studies revealed the presence of extra oxygen atoms as well as gallium species in the layer, leading to the conclusion that phosphonate and hydrogenophosphonate ions are present in the PPA layer intercalated with H3O+ and Ga3+ ions. This mechanism enables the formation of layers approximately 10 times thicker than those obtained with lower H2O percentages. HREELS indicated that the surface is composed of regions covered by PPA layers and uncovered regions, but the uncovered regions disappeared for water contents equal to or higher than 5%. XPS results are interpreted using a model consisting of a monolayer partially covering the surface and a thick layer. This model is consistent with AFM images revealing roughness on the order of 7 nm for the thick layer and 0.2-0.5 nm for the thin layer. Sonication proves to be an effective method for reducing layer thickness.