Dilute Donor Organic Solar Cells Based on Non-fullerene Acceptors.

The advent of small molecule non-fullerene acceptor (NFA) materials for organic photovoltaic (OPV) devices has led to a series of breakthroughs in performance and device lifetime. The most efficient OPV devices have a combination of electron donor and acceptor materials that constitute the light absorbing layer in a bulk heterojunction (BHJ) structure. For many BHJ-based devices reported to date, the weight ratio of donor to acceptor is near equal. However, the morphology of such films can be difficult to reproduce and manufacture at scale. There would be an advantage in developing a light harvesting layer for efficient OPV devices that contains only a small amount of either the donor or acceptor. In this work we explore low donor content OPV devices composed of the polymeric donor PM6 blended with high performance NFA materials, Y6 or ITIC-4F. We found that even when the donor:acceptor weight ratio was only 1:10, the OPV devices still have good photoconversion efficiencies of around 6% and 5% for Y6 and ITIC-4F, respectively. It was found that neither charge mobility nor recombination rates had a strong effect on the efficiency of the devices. Rather, the overall efficiency was strongly related to the film absorption coefficient and maintaining adequate interfacial surface area between donor and acceptor molecules/phases for efficient exciton dissociation.

Reconstructing the 3D Coordinates of Guest:Host OLED Blends with Single Atom Resolution.

The performance of electronic and semiconductor devices is critically dependent on the distribution of guest molecules or atoms in a host matrix. One prominent example is that of organic light-emitting diode (OLED) displays containing phosphorescent emitters, now ubiquitous in handheld devices and high-end televisions. In such OLEDs the phosphorescent guest [normally an iridium(III)-based complex] is typically blended into a host matrix, and charge injection and transport, exciton formation and decay, and hence overall device performance are governed by the distribution of the emissive guest in the host. Here high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) is used with depth sectioning to reconstruct the 3D distribution of emissive iridium(III) complexes, fac-tris(2-phenylpyridine)iridium(III) [Ir(ppy)3], blended into the amorphous host material, tris(4-carbazoyl-9-ylphenyl)amine (TCTA), by resolving the position of each single iridium(III) ion. It is found that most Ir(ppy)3 complexes are clustered with at least one other, even at low concentrations, and that for films of 20 wt.% Ir(ppy)3 essentially all the complexes are interconnected. The results validate the morphology of blend films created using molecular dynamics simulations which mimic the evaporation film-forming process and are also consistent with the experimentally measured charge transport and photophysical properties.

Differentiating Between V- and G-Series Nerve Agent and Simulant Vapours Using Fluorescent Film Responses.

In-field rapid and reliable identification of nerve agents is critical for the protection of Defence and National Security personnel as well as communities. Fluorescence-based detectors can be portable and provide rapid detection of chemical threats. However, most current approaches cannot differentiate between dilute vapors of nerve agent classes and are susceptible to false positives due to the presence of common acids. Here a fluorescence-based method is shown for rapid differentiation between the V-series and phosphonofluoridate G-series nerve agents and avoids false positives due to common acids. Differentiation is achieved through harnessing two different mechanisms. Detection of the V-series is achieved using photoinduced hole transfer whereby the fluorescence of the sensing material is quenched in the presence of the V-series agent. The G-series is detected using a turn-on mechanism in which a silylated excited state intramolecular proton transfer sensing molecule is selectively deprotected by hydrogen fluoride, which is typically found as a contaminant and/or breakdown product in G-series agents such as sarin. The strategy provided discrimination between classes, as the sensor for the G-series agent class is insensitive to the V-series agent, and vice versa, and neither responded to common acids.

Fluorinated Cation-Based 2D Perovskites for Efficient and Stable 3D/2D Heterojunction Perovskite Solar Cells.

Three-dimensional (3D) perovskite solar cells (PSCs) containing additives capable of forming two-dimensional (2D) structures in neat films have attracted attention due to their ability to enhance power conversion efficiency (PCE) in combination with improved operational stability. Herein, a newly designed fluorinated ammonium salt, 2-(perfluorophenyl)ethanaminium bromide:chloride50:50 (FEABr:Cl50:50), is introduced into CsMAFAPbI3-based PSCs with a standard n-i-p architecture. FEABr:Cl50:50 was used as an additive in the tin(IV) oxide (SnO2) electron transporting layer (ETL) as well as a surface treatment for the perovskite film. Used in this dual way, the additive was found to passivate charge-trapping defects within the SnO2 ETL and regulate the crystal growth of the perovskite layer. When FEABr:Cl50:50 was deposited onto the surface of the 3D perovskite film, it formed a thin hydrophobic 2D capping layer. Adopting this dual strategy led to the perovskite film having larger grain sizes, improved quality, and overall better device performance. As a result, the best-performing device exhibited a PCE of over 23% with negligible hysteresis in an n-i-p device architecture with an area of 0.2 cm2. Furthermore, unencapsulated devices with the hydrophobic 2D capping layer showed improved stability compared to the control device when measured under continuous light irradiation at a maximum power point (MPP) at 80 ± 5 °C in a humid (≈50%) environment.

Utilizing Different Diffusion Mechanisms for Thin Film Fluorescence-Based Detection and Discrimination of Illicit Drug Vapors.

Film-based fluorescence sensors have been demonstrated to be powerful tools for real-time detection of trace chemical vapors. While explosive vapor detection via fluorescence quenching has been widely explored, fluorescence-based real-time detection and identification of illicit drug vapors remains a challenge. Here, we report two perylene diimide-based sensing materials, P1 and P2, incorporating 2,2-dihexyloctanyl chains and 4-[tris(4-{tert-butyl}phenyl)methyl]phenyl moieties at the imide positions, respectively. Quartz crystal microbalance with in situ photoluminescence measurements showed that N-methylphenethylamine, a simulant of methamphetamine (MA), diffused into films of P1 and P2 via Fickian and case-II mechanisms, respectively. The difference in the analyte diffusion mechanism led to P2 showing significantly faster luminescence quenching but slower luminescence recovery compared to P1. Finally, the different diffusion mechanisms were used as the basis for developing a simple sensor array based on P1 and P2 that could selectively detect free-base illicit drugs (MA, cocaine, and tetrahydrocannabinol) from potential interferants (organic amines, alcohol, and cosmetics) within 40 s.

Perylene Diimide Based Fluorescent Sensors for Drug Simulant Detection: The Effect of Alkyl-Chain Branching on Film Morphology, Exciton Diffusion, Vapor Diffusion, and Sensing Response.

Luminescence-based sensing has been demonstrated to be a powerful method for rapid trace detection of chemical vapors (analytes). Analyte diffusion has been shown to be the critical factor for real-time luminescence-based detection of explosive analytes via photoinduced electron transfer in amorphous films of conjugated polymers and dendrimers. However, similar studies to determine the critical factors for sensing have not been performed on materials that employ photoinduced hole transfer (PHT) to detect low electron affinity analytes such as illicit drugs. Nor have such studies been performed on semicrystalline sensing films. We have developed a family of perylene diimide-based sensing materials capable of undergoing PHT with amine-group containing analytes. It was found that the choice of branched alkyl chain [1-hexylheptyl (PHH), 2-hexyloctyl (PHO), or 2,2-dihexyloctyl (PDHO)] attached to the nitrogen atoms of the imide moiety strongly affected the solution-processed film morphology. PHH and PHO were found to contain crystalline phases, whereas PDHO was essentially amorphous. The degree of crystallinity strongly influenced exciton diffusion, with PHH and PHO exhibiting exciton diffusion coefficients that were 20× and 10× greater than the value of the amorphous PDHO. The degree of film crystallinity was also found to be critical when the films were applied to detect N-methylphenethylamine (MPEA), a simulant of methamphetamine. While PHH had the largest exciton diffusion coefficient [(1.0 ± 0.2) × 10-2 cm2 s-1] and analyte uptake (12.3 ± 1.8 ng) it showed the smallest quenching efficiency (2.6% ng-1). In contrast, PHO, which sorbed the least analyte (6.1 ± 0.4 ng) of the three compounds, had the largest quenching efficiency (7.1% ng-1) due to its molecular packing and hence exciton diffusion coefficient [(4.5 ± 1.4) × 10-3 cm2 s-1] not being affected by sorption of the analyte. These results show that when applying fluorescent films in practical detection scenarios there is a potential trade-off between a high exciton diffusion constant and analyte diffusion for semicrystalline sensing materials and that a high exciton diffusion coefficient in an as-cast film does not necessarily translate into a more efficient fluorescent quenching. The results also show that sensing materials that form semicrystalline films, whose packing is not disrupted by analyte diffusion, provide a route for overcoming these effects and achieving high sensitivity.

The impact of film deposition and annealing on the nanostructure and dielectric constant of organic semiconductor thin films.

The strategy of using a bulk-heterojunction light-absorbing layer has led to the most efficient organic solar cells. However, optimising the blend morphology to maximise light absorption, charge generation and extraction can be challenging. Homojunction devices containing a single component have the potential to overcome the challenges associated with bulk heterojunction films. A strategy towards this goal is to increase the dielectric constant of the organic semiconductor to ≈10, which in principle would lead to free charge carrier generation upon photoexcitation. However, the factors that affect the thin film dielectric constants are still not well understood. In this work we report an organic semiconductor material that can be solution processed or vacuum evaporated to form good quality thin films to explore the effect of chromophore structure and film morphology on the dielectric constant and other optoelectronic properties. 2,2'-[(4,4,4',4'-Tetrakis{2-[2-methoxyethoxy]ethyl}-4H,4'H-{2,2'-bi[cyclo-penta[2,1-b:3,4-b']dithiophene]}-6,6'-diyl)bis(methaneylylidene)]dimalononitrile [D(CPDT-DCV)] was designed to have high electron-affinity end groups and low ionisation-potential central moieties. It can be processed from solution or be thermally evaporated, with the film morphology changing from face-on to a herringbone arrangement upon solvent or thermal annealing. The glycol solubilising groups led to the static dielectric constant (taken from capacitance measurements) of the films to be between 6 and 7 (independent of processing conditions), while the optical frequency dielectric constant depended on the processing conditions. The less ordered solution processed film was found to have the lowest optical frequency dielectric constant of 3.6 at 2.0 × 1014 Hz, which did not change upon annealing. In contrast, the more ordered evaporated film had an optical frequency dielectric constant 20% higher at 4.2 and thermal annealing further increased it to 4.5, which is amongst the highest reported for an organic semiconductor at that frequency. Finally, the more ordered evaporated films had more balanced charge transport, which did not change upon annealing.

Twisted Carbazole Dendrons for Solution-Processable Green Emissive Phosphorescent Dendrimers.

A family of first-generation dendrimers containing 3,5-bis(carbazolyl)phenyl dendrons attached to a green emissive fac-tris(2-phenylpyridyl)iridium(III) core were prepared. The solubility of the dendrimers was imparted by the attachment of tert-butyl surface groups to the carbazole moieties. The dendrimers differed in the number of dendrons attached to each ligand (one or two dendrons) as well as the degree of rotational restriction within the dendrons. The densities of the films containing the doubly dendronized materials were higher than those of their mono-dendronized counterparts, with the dendrimer containing two rotationally constrained dendrons per ligand having the highest density at 1.12 ± 0.04 g cm-3. The dendrimers were found to have high photoluminescence quantum yields (PLQYs) in solution of between 80 and 90%, with the doubly dendronized materials having the lower values and a red-shifted emission. The neat film PLQY values of the dendrimers were less than those measured in solution although the relative decrease was smaller for the doubly dendronized materials. The dendrimers were incorporated into solution-processed bilayer organic light-emitting diodes (OLEDs) composed of neat or blend emissive layers and an electron transport layer. The best-performing devices had the dendrimers blended with a host material and external quantum efficiencies as high as 14.0%, which is higher than previously reported results for carbazole-incorporating emissive dendrimers. A feature of the devices containing blends of the doubly dendronized materials was that the maximum efficiency was relatively insensitive to the concentration in the host between 1 and 7 mol %.

PyThinFilm: Automated Molecular Dynamics Simulation Protocols for the Generation of Thin Film Morphologies.

The performance of organic optoelectronic devices, such as organic light-emitting diodes (OLEDs) and organic solar cells (OSCs), is intrinsically related to the molecular-scale morphology of the thin films from which they are composed. However, the experimental characterization of morphology at the molecular level is challenging due to the often amorphous or at best semicrystalline nature of these films. Classical molecular modeling techniques, such as molecular dynamics (MD) simulation, are increasingly used to understand the relationship between morphology and the properties of thin-film devices. PyThinFilm (github.com/ATB-UQ/PyThinFilm) is an open-source Python package which allows fully automated MD simulations of thin film growth to be performed using vacuum and/or solution deposition processes. PyThinFilm utilizes the GROMACS simulation package in combination with interaction parameters from the Automated Topology Builder (atb.uq.edu.au). Here, PyThinFilm is described along with an overview of applications in which PyThinFilm has been used to study the thin films of organic semiconductor materials typically used in OLEDs and OSCs.

Fluorinated Interlayer Modulation of NiOx-Based Inverted Perovskite Solar Cells.

p-Type inorganic nickel oxide (NiOx) exhibits high transparency, tunable-optoelectronic properties, and a work function (WF) that is potentially suitable for hole extraction in inverted perovskite solar cells (PSCs). However, NiOx films possess surface defects that lead to high interfacial recombination and an energy offset with the ionization potential of the perovskite. Herein, we show that fluorinated 3-(2,3,4,5,6-pentafluorophenyl)propan-1-aminium iodide (FPAI) can be used to modify the electronic properties of the NiOx anode interlayer. The FPAI modification led to good perovskite crystal growth and films with reduced surface defects. The FPAI modification also increased the WF of NiOx and improved charge extraction. These improvements led to an increased Voc value compared with control devices without FPAI modification, 1.05 V versus 1.00 V, and a higher short-circuit current and larger fill factor. As a result, the best PSCs with FPAI-modified NiOx had a power conversion efficiency of 19.3%. Finally, the PSCs with the FPAI-modified NiOx layer were found to have improved stability.

Influence of the Alkyl Chain Length of (Pentafluorophenylalkyl) Ammonium Salts on Inverted Perovskite Solar Cell Performance.

We study the effect of (2,3,4,5,6-pentafluorophenyl)alkylamine additives with differing alkyl chain lengths (methyl, ethyl, and n-propyl) on the performance of methylammonium lead triiodide (MAPbI3) perovskite solar cells. The results show that the length of the alkyl chain between the 2,3,4,5,6-pentafluorophenyl group and ammonium moiety has a critical effect on the perovskite film structure and subsequent device performance. The 2,3,4,5,6-pentafluorophenyl ammonium additive with the shortest linking group (a methylene unit), namely (2,3,4,5,6-pentafluorophenyl)methylammonium iodide, was found to be distributed throughout the bulk of the perovskite film with a 2D phase only being observable at high concentrations (>30 mol%). In contrast, the additives with ethyl and n-propyl linking groups phase-separate during solution processing and are found to concentrate at the surface of the perovskite film. Photoluminescence measurements showed that the fluorinated additives passivated the surface defects on the perovskite grains. Of the three additives, inverted devices containing 0.32 mol% of the 2,3,4,5,6-pentafluorophenyl ammonium additive with the methylene linking group achieved a maximum power conversion efficiency of 22.0%, with the device efficiency decreasing with increasing additive concentration. In contrast, the devices composed of the additive with the longest alkyl linker, 3-(2,3,4,5,6-pentafluorophenyl)propylammonium iodide, had the poorest performance, with PCEs less than that of the neat MAPbI3 control and decreasing with increasing additive concentration.

Understanding the performance differences between solution and vacuum deposited OLEDs: A computational approach.

Solution-processing of organic light-emitting diode films has potential advantages in terms of cost and scalability over vacuum-deposition for large area applications. However, solution processed small molecule films can have lower overall device performance. Here, novel molecular dynamics techniques are developed to enable faster simulation of solvent evaporation that occurs during solution processing and give films of thicknesses relevant to real devices. All-atom molecular dynamics simulations are then used in combination with kinetic Monte Carlo transport modeling to examine how differences in morphology stemming from solution or vacuum film deposition affect charge transport and exciton dynamics in films consisting of light-emitting bis(2-phenylpyridine)(acetylacetonate)iridium(III) [Ir(ppy)2(acac)] guest molecules in a 4,4'-bis(N-carbazolyl)biphenyl host. While the structures of the films deposited from vacuum and solution were found to differ, critically, only minor variations in the transport properties were predicted by the simulations even if trapped solvent was present.

Diffusion in Organic Film Stacks Containing Solution-Processed Phosphorescent Poly(dendrimer) Dopants.

Efficient organic light-emitting diodes (OLEDs) consist of an emissive layer comprising a blend of a light-emitting and host material in contact with one or more charge transporting layers. The distribution of the active material in the guest-host emissive layer blend and the changes that may occur upon thermal annealing are two important factors in determining the stability and efficiency of OLEDs. We have combined neutron reflectometry and photoluminescence measurements to investigate the structures of films comprising an emissive layer containing a phosphorescent poly(dendrimer) material blended with 4,4'-N,N'-di(carbazolyl)biphenyl. This combination has been shown to give rise to highly efficient OLEDs. Here, we show that the emissive poly(dendrimer) material was not uniformly distributed in the host, but formed a concentration gradient within the emissive layer. Upon heating, the adjacent electron transport layer was found to intermix with the emissive layer, accompanied by changes in the material distribution in the emissive layer. The intermixing of the materials led to a decrease in the photoluminescence from the poly(dendrimer) within the film. The decrease in the photoluminescence was ascribed to an increase in interchromophore interactions that could arise from a conformational change of the poly(dendrimer) or phase separation leading to aggregation. The results indicate that, while uniform mixing of the guest and host is not essential for efficiency, the thermal stabilities of both host and charge transport materials are important for device durability.

Unraveling exciton processes in Ir(ppy)3:CBP OLED films upon photoexcitation.

Emissive layers in phosphorescent organic light-emitting diodes commonly make use of guest-host blends such as Ir(ppy)3:CBP to achieve high external quantum efficiencies. However, while the Ir(ppy)3:CBP blend has been studied experimentally, crucial questions remain regarding how exciton diffusion is dependent on the distribution of the guest in the host, which can currently only be addressed at the atomic level via computational modeling. In this work, kinetic Monte Carlo simulations are utilized to gain insight into exciton diffusion in Ir(ppy)3:CBP blend films. The effects of both guest concentration and exciton density on various system properties are analyzed, including the probability of singlet excitons being converted to triplets, and the probability of those triplets decaying radiatively. Significantly, these simulations suggest that triplet diffusion occurs almost exclusively via guest-guest Dexter transfer and that concentration quenching of triplets induced by guest-guest intermolecular dipole-dipole interactions has a negligible effect at high exciton densities due to the prevalence of triplet-triplet annihilation. Furthermore, results for vacuum deposited morphologies derived from molecular dynamics simulations are compared to the results obtained using a simple cubic lattice approximation with randomly distributed guest molecules. We show that while differences in host-based processes such as singlet diffusion are observed, overall, the results on the fate of the excitons are in good agreement for the two morphology types, particularly for guest-based processes at low guest concentrations where guest clustering is limited.

Engineering fluorinated-cation containing inverted perovskite solar cells with an efficiency of >21% and improved stability towards humidity.

Efficient and stable perovskite solar cells with a simple active layer are desirable for manufacturing. Three-dimensional perovskite solar cells are most efficient but need to have improved environmental stability. Inclusion of larger ammonium salts has led to a trade-off between improved stability and efficiency, which is attributed to the perovskite films containing a two-dimensional component. Here, we show that addition of 0.3 mole percent of a fluorinated lead salt into the three-dimensional methylammonium lead iodide perovskite enables low temperature fabrication of simple inverted solar cells with a maximum power conversion efficiency of 21.1%. The perovskite layer has no detectable two-dimensional component at salt concentrations of up to 5 mole percent. The high concentration of fluorinated material found at the film-air interface provides greater hydrophobicity, increased size and orientation of the surface perovskite crystals, and unencapsulated devices with increased stability to high humidity.

Acid is a potential interferent in fluorescent sensing of chemical warfare agent vapors.

A common feature of fluorescent sensing materials for detecting chemical warfare agents (CWAs) and simulants is the presence of nitrogen-based groups designed to nucleophilically displace a phosphorus atom substituent, with the reaction causing a measurable fluorescence change. However, such groups are also basic and so sensitive to acid. In this study we show it is critical to disentangle the response of a candidate sensing material to acid and CWA simulant. We report that pyridyl-containing sensing materials designed to react with a CWA gave a strong and rapid increase in fluorescence when exposed to Sarin, which is known to contain hydrofluoric acid. However, when tested against acid-free diethylchlorophosphate and di-iso-propylfluorophosphate, simulants typically used for evaluating novel G-series CWA sensors, there was no change in the fluorescence. In contrast, simulants that had been stored or tested under a standard laboratory conditions all led to strong changes in fluorescence, due to acid impurities. Thus the results provide strong evidence that care needs to be taken when interpreting the results of fluorescence-based solid-state sensing studies of G-series CWAs and their simulants. There are also implications for the application of these pyridyl-based fluorescence and other nucleophilic/basic sensing systems to real-world CWA detection.

Pyrrolo[3,2-b]pyrrole-1,4-dione (IsoDPP) End Capped with Napthalimide or Phthalimide: Novel Small Molecular Acceptors for Organic Solar Cells.

We introduce two novel solution-processable electron acceptors based on an isomeric core of the much explored diketopyrrolopyrrole (DPP) moiety, namely pyrrolo[3,2-b]pyrrole-1,4-dione (IsoDPP). The newly designed and synthesized compounds, 6,6'-[(1,4-bis{4-decylphenyl}-2,5-dioxo-1,2,4,5-tetrahydropyrrolo[3,2-b]pyrrole-3,6-diyl)bis(thiophene-5,2-diyl)]bis[2-(2-butyloctyl)-1H-benzo[de]isoquinoline-1,3(2H)-dione] (NAI-IsoDPP-NAI) and 5,5'-[(1,4-bis{4-decylphenyl}-2,5-dioxo-1,2,4,5-tetrahydropyrrolo[3,2-b]pyrrole-3,6-diyl)bis(thiophene-5,2-diyl)]bis[2-(2-butyloctyl)isoindoline-1,3-dione] (PI-IsoDPP-PI) have been synthesized via Suzuki couplings using IsoDPP as a central building block and napthalimide or phthalimide as end-capping groups. The materials both exhibit good solubility in a wide range of organic solvents including chloroform (CF), dichloromethane (DCM), and tetrahydrofuran (THF), and have a high thermal stability. The new materials absorb in the wavelength range of 300-600 nm and both compounds have similar electron affinities, with the electron affinities that are compatible with their use as acceptors in donor-acceptor bulk heterojunction (BHJ) organic solar cells. BHJ devices comprising the NAI-IsoDPP-NAI acceptor with poly(3-n-hexylthiophene) (P3HT) as the donor were found to have a better performance than the PI-IsoDPP-PI containing cells, with the best device having a VOC of 0.92 V, a JSC of 1.7 mAcm-2, a FF of 63%, and a PCE of 0.97%.

Evolution and Morphology of Thin Films Formed by Solvent Evaporation: An Organic Semiconductor Case Study.

The crucial role played by the solution-vapor interface in determining the growth and morphology of an organic semiconductor thin film formed by solvent evaporation has been examined in atomic detail. Specifically, how the loss of individual solvent molecules from the surface of the solution induces solute assembly has been studied using molecular dynamics simulations. The system consisted of bis(2-phenylpyridine) (acetylacetonate)iridium(III) [Ir(ppy)2(acac)] and 4,4'-bis(N-carbazolyl)-1,1'-biphenyl (CBP) in chloroform at 310 K. The simulations clearly indicate that (a) the system does not undergo uniform phase separation (spinodal decomposition), (b) solute aggregation initiates at the solution-vapor interface, (c) the distribution of solvent in the film is nonhomogeneous, (d) this nonhomogeneous distribution can induce preferential alignment of host molecules, and (e) a portion of the solvent likely remains trapped within the film. The work not only demonstrates the ability to directly model evaporation in atomic detail on the relevant length scales but also shows that atomistic simulations have the potential to shed new light on morphological properties of a wide range of organic semiconductor devices manufactured using solution-processing methods.

Defect/Interface Recombination Limited Quasi-Fermi Level Splitting and Open-Circuit Voltage in Mono- and Triple-Cation Perovskite Solar Cells.

Multication metal-halide perovskites exhibit desirable performance and stability, compared to their monocation counterparts. However, the study of the photophysical properties and the nature of defect states in these materials is still a challenging and ongoing task. Here, we study bulk and interfacial energy loss mechanisms in solution-processed MAPbI3 (MAPI) and (CsPbI3)0.05[(FAPbI3)0.83(MAPbBr3)0.17]0.95 (triple cation) perovskite solar cells using absolute photoluminescence (PL) measurements. In neat MAPI films, we find a significantly smaller quasi-Fermi level splitting than for the triple cation perovskite absorbers, which defines the open-circuit voltage of the MAPI cells. PL measurements at low temperatures (∼20 K) on MAPI films demonstrate that emissive subgap states can be effectively reduced using different passivating agents, which lowers the nonradiative recombination loss at room temperature. We conclude that while triple cation perovskite cells are limited by interfacial recombination, the passivation of surface trap states within the MAPI films is the primary consideration for device optimization.

Perdeuterated Conjugated Polymers for Ultralow-Frequency Magnetic Resonance of OLEDs.

The formation of excitons in OLEDs is spin dependent and can be controlled by electron-paramagnetic resonance, affecting device resistance and electroluminescence yield. We explore electrically detected magnetic resonance in the regime of very low magnetic fields (<1 mT). A pronounced feature emerges at zero field in addition to the conventional spin- 1 / 2 Zeeman resonance for which the Larmor frequency matches that of the incident radiation. By comparing a conventional π-conjugated polymer as the active material to a perdeuterated analogue, we demonstrate the interplay between the zero-field feature and local hyperfine fields. The zero-field peak results from a quasistatic magnetic-field effect of the RF radiation for periods comparable to the carrier-pair lifetime. Zeeman resonances are resolved down to 3.2 MHz, approximately twice the Larmor frequency of an electron in Earth's field. However, since reducing hyperfine fields sharpens the Zeeman peak at the cost of an increased zero-field peak, we suggest that this result may constitute a fundamental low-field limit of magnetic resonance in carrier-pair-based systems. OLEDs offer an alternative solid-state platform to investigate the radical-pair mechanism of magnetic-field effects in photochemical reactions, allowing models of biological magnetoreception to be tested by measuring spin decoherence directly in the time domain by pulsed experiments.