Change in re-use value of incinerated sewage sludge ash due to chemical extraction of phosphorus.

The potential of six different extractants to recover phosphorus (P) from incinerated sewage sludge ash (ISSA) was evaluated. Secondary effects such as the co-dissolution of Zn and Cu were also considered. The residual ISSA from each study was assessed in particular detail, focusing on the leachability of remaining Zn and Cu, major element composition, crystalline phases and overall degree of crystallinity and particle size distribution. The residual ISSA was also evaluated as a pozzolanic material using a Strength Activity Index (SAI) test with mortars containing Portland cement with a 20% substitution by ISSA. All results were compared to tests with untreated ISSA. Overall, the use of 3 of the 6 extractants could be ruled out due to poor P recovery potential and/or a serious compromise of the potential reuse of residual ISSA in Portland cement-based materials. The results highlight the added value of considering the potential reuse of residual ISSA when trying to optimize P recovery from ISSA by wet methods.

Phosphorus recovery and leaching of trace elements from incinerated sewage sludge ash (ISSA).

Chemical extraction of phosphorus (P) from incinerated sewage sludge ash (ISSA) is adversely influenced by co-dissolution of metals and metalloids. This study investigated P recovery and leaching of Zn, Cu, Pb, As and Ni from ISSA using inorganic acids (sulphuric acid and nitric acid), organic acids (oxalic acid and citric acid), and chelating agents (ethylenediaminetetraacetic acid (EDTA) and ethylene diamine tetramethylene phosphonate (EDTMP)). The aim of this study was to optimize a leaching process to recover P-leachate with high purity for P fertilizer production. The results show that both organic and inorganic acids extract P-containing phases but organic acids leach more trace elements, particularly Cu, Zn, Pb and As. Sulphuric acid was the most efficient for P recovery and achieved 94% of total extraction under the optimal conditions, which were 2-h reaction with 0.2 mol/L H2SO4 at a liquid-to-solid ratio of 20:1. EDTA extracted only 20% of the available P, but the leachates were contaminated with high levels of trace elements under optimum conditions (3-h reaction with EDTA at 0.02 mol/L, pH 2, and liquid-to-solid ratio of 20:1). Therefore, EDTA was considered an appropriate pre-treatment agent for reducing the total metal/metalloid content in ISSA, which produced negligible changes in the structure of ISSA and reduced contamination during subsequent P extraction using sulphuric acid.

Optimising the bioreceptivity of porous glass tiles based on colonization by the alga Chlorella vulgaris.

Green façades on buildings can mitigate greenhouse gas emissions. An option to obtain green facades is through the natural colonisation of construction materials. This can be achieved by engineering bioreceptive materials. Bioreceptivity is the susceptibility of a material to be colonised by living organisms. The aim of this research was to develop tiles made by sintering granular waste glass that were optimised for bioreceptivity of organisms capable of photosynthesis. Tiles were produced by pressing recycled soda-lime glass with a controlled particle size distribution and sintering compacted samples at temperatures between 680 and 740°C. The primary bioreceptivity of the tiles was evaluated by quantifying colonisation by the algae Chlorella vulgaris (C. vulgaris), which was selected as a model photosynthetic micro-organism. Concentrations of C. vulgaris were measured using chlorophyll-a extraction. Relationships between bioreceptivity and the properties of the porous glass tile, including porosity, sorptivity, translucency and pH are reported. Capillary porosity and water sorptivity were the key factors influencing the bioreceptivity of porous glass. Maximum C. vulgaris growth and colonisation was obtained for tiles sintered at 700°C, with chlorophyll-a concentrations reaching up to 11.1±0.4µg/cm(2) of tile. Bioreceptivity was positively correlated with sorptivity and porosity and negatively correlated with light transmittance. The research demonstrates that the microstructure of porous glass, determined by the processing conditions, significantly influences bioreceptivity. Porous glass tiles with high bioreceptivity that are colonised by photosynthetic algae have the potential to form carbon-negative façades for buildings and green infrastructure.

Production of pyroxene ceramics from the fine fraction of incinerator bottom ash.

Incinerator bottom ash (IBA) is normally processed to extract metals and the coarse mineral fraction is used as secondary aggregate. This leaves significant quantities of fine material, typically less than 4mm, that is problematic as reuse options are limited. This work demonstrates that fine IBA can be mixed with glass and transformed by milling, calcining, pressing and sintering into high density ceramics. The addition of glass aids liquid phase sintering, milling increases sintering reactivity and calcining reduces volatile loss during firing. Calcining also changes the crystalline phases present from quartz (SiO2), calcite (CaCO3), gehlenite (Ca2Al2SiO7) and hematite (Fe2O3) to diopside (CaMgSi2O6), clinoenstatite (MgSiO3) and andradite (Ca3Fe2Si3O12). Calcined powders fired at 1080°C have high green density, low shrinkage (<7%) and produce dense (2.78 g/cm(3)) ceramics that have negligible water absorption. The transformation of the problematic fraction of IBA into a raw material suitable for the manufacture of ceramic tiles for use in urban paving and other applications is demonstrated.

Long-term temporal trends and estimated transmission rates for Mycobacterium bovis infection in an undisturbed high-density badger (Meles meles) population.

We describe epidemiological trends in Mycobacterium bovis infection in an undisturbed wild badger (Meles meles) population. Data were derived from the capture, clinical sampling and serological testing of 1803 badgers over 9945 capture events spanning 24 years. Incidence and prevalence increased over time, exhibiting no simple relationship with host density. Potential explanations are presented for a marked increase in the frequency of positive serological test results. Transmission rates (R0) estimated from empirical data were consistent with modelled estimates and robust to changes in test sensitivity and the spatial extent of the population at risk. The risk of a positive culture or serological test result increased with badger age, and varied seasonally. Evidence consistent with progressive disease was found in cubs. This study demonstrates the value of long-term data and the repeated application of imperfect diagnostic tests as indices of infection to reveal epidemiological trends in M. bovis infection in badgers.

Metal leaching from monolithic stabilised/solidified air pollution control residues.

Portland cement (CEM I) and ground granulated blast furnace slag (ggbs) have been used to treat air pollution control (APC) residues from an energy-from-waste plant burning municipal solid waste. Stabilised/solidified (s/s) products were prepared with binder additions ranging from 10 to 50 wt.% of total dry mass and water/solids ratios between 0.40 and 0.80. Monolithic leach tests (EA NEN 7375:2004) indicated that 50% binder additions were necessary to meet the UK monolithic Waste Acceptance Criteria (monWAC) for Pb and Zn, and previous work indicated that chloride leaching exceeded WAC even at this binder addition. Lower binder additions (20 and 10%) did not sufficiently reduce leaching of Pb. Although the monWAC are based on an assumption that leaching is diffusion-controlled, evaluation of leaching mechanisms indicates that more complex processes than diffusion occur for s/s APC residues.

Production of technical grade phosphoric acid from incinerator sewage sludge ash (ISSA).

The recovery of phosphorus from sewage sludge ash samples obtained from 7 operating sludge incinerators in the UK using a sulfuric acid washing procedure to produce a technical grade phosphoric acid product has been investigated. The influences of reaction time, sulfuric acid concentration, liquid to solid ratio and source of ISSA on P recovery have been examined. The optimised conditions were the minimum stoichiometric acid requirement, a reaction time of 120 min and a liquid to solid ratio of 20. Under these conditions, average recoveries of between 72% and 91% of total phosphorus were obtained. Product filtrate was purified by passing through a cation exchange column, concentrated to 80% H(3)PO(4) and compared with technical grade H(3)PO(4) specifications. The economics of phosphate recovery by this method are briefly discussed.

Production of geopolymers using glass produced from DC plasma treatment of air pollution control (APC) residues.

Air pollution control (APC) residues are the hazardous waste produced from cleaning gaseous emissions at energy-from-waste (EfW) facilities processing municipal solid waste (MSW). APC residues have been blended with glass-forming additives and treated using DC plasma technology to produce a high calcium alumino-silicate glass. This research has investigated the optimisation and properties of geopolymers prepared from this glass. Work has shown that high strength geopolymers can be formed and that the NaOH concentration of the activating solution significantly affects the properties. The broad particle size distribution of the APC residue glass used in these experiments results in a microstructure that contains unreacted glass particles included within a geopolymer binder phase. The high calcium content of APC residues may cause the formation of some amorphous calcium silicate hydrate (C-S-H) gel. A mix prepared with S/L=3.4, Si/Al=2.6 and [NaOH]=6M in the activating solution, produced high strength geopolymers with compressive strengths of approximately 130 MPa. This material had high density (2070 kg/m(3)) and low porosity. The research demonstrates for the first time that glass derived from DC plasma treatment of APC residues can be used to form high strength geopolymer-glass composites that have potential for use in a range of applications.

EU landfill waste acceptance criteria and EU Hazardous Waste Directive compliance testing of incinerated sewage sludge ash.

A hazardous waste assessment has been completed on ash samples obtained from seven sewage sludge incinerators operating in the UK, using the methods recommended in the EU Hazardous Waste Directive. Using these methods, the assumed speciation of zinc (Zn) ultimately determines if the samples are hazardous due to ecotoxicity hazard. Leaching test results showed that two of the seven sewage sludge ash samples would require disposal in a hazardous waste landfill because they exceed EU landfill waste acceptance criteria for stabilised non-reactive hazardous waste cells for soluble selenium (Se). Because Zn cannot be proven to exist predominantly as a phosphate or oxide in the ashes, it is recommended they be considered as non-hazardous waste. However leaching test results demonstrate that these ashes cannot be considered as inert waste, and this has significant implications for the management, disposal and re-use of sewage sludge ash.

Properties of sintered glass-ceramics prepared from plasma vitrified air pollution control residues.

Air pollution control (APC) residues, obtained from a major UK energy from waste (EfW) plant, processing municipal solid waste, have been blended with silica and alumina and melted using DC plasma arc technology. The glass produced was crushed, milled, uni-axially pressed and sintered at temperatures between 750 and 1150 degrees C, and the glass-ceramics formed were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Mechanical properties assessed included Vickers's hardness, flexural strength, Young's modulus and thermal shock resistance. The optimum sintering temperature was found to be 950 degrees C. This produced a glass-ceramic with high density (approximately 2.58 g/cm(3)), minimum water absorption (approximately 2%) and relatively high mechanical strength (approximately 81+/-4 MPa). Thermal shock testing showed that 950 degrees C sintered samples could withstand a 700 degrees C quench in water without micro-cracking. The research demonstrates that glass-ceramics can be readily formed from DC plasma treated APC residues and that these have comparable properties to marble and porcelain. This novel approach represents a technically and commercially viable treatment option for APC residues that allow the beneficial reuse of this problematic waste.

Social group size affects Mycobacterium bovis infection in European badgers (Meles meles).

1. In most social animals, the prevalence of directly transmitted pathogens increases in larger groups and at higher population densities. Such patterns are predicted by models of Mycobacterium bovis infection in European badgers (Meles meles). 2. We investigated the relationship between badger abundance and M. bovis prevalence, using data on 2696 adult badgers in 10 populations sampled at the start of the Randomized Badger Culling Trial. 3. M. bovis prevalence was consistently higher at low badger densities and in small social groups. M. bovis prevalence was also higher among badgers whose genetic profiles suggested that they had immigrated into their assigned social groups. 4. The association between high M. bovis prevalence and small badger group size appeared not to have been caused by previous small-scale culling in study areas, which had been suspended, on average, 5 years before the start of the current study. 5. The observed pattern of prevalence might occur through badgers in smaller groups interacting more frequently with members of neighbouring groups; detailed behavioural data are needed to test this hypothesis. Likewise, longitudinal data are needed to determine whether the size of infected groups might be suppressed by disease-related mortality. 6. Although M. bovis prevalence was lower at high population densities, the absolute number of infected badgers was higher. However, this does not necessarily mean that the risk of M. bovis transmission to cattle is highest at high badger densities, since transmission risk depends on badger behaviour as well as on badger density.

Fitness to fly post craniotomy--a survey of medical advice from long-haul airline carriers.

Commercial airline passengers are subject to numerous medical risks while in transit. Seventeen long-haul airline companies were questioned concerning fitness to travel and the case of a patient wishing to travel post craniotomy. Three airline companies gave satisfactory medical information, while the remaining airlines felt it was the decision of the operating surgeon rather than the airline company. A literature review shows that post operative pneumocephalus and the risk of tension pneumocephalus is the major medical concern when transporting patients post craniotomy. Evidence is contradictory with respect to the importance of this potentially life threatening problem. Postoperative 100% oxygen may improve the rate of pneumocephalus absorption. Airline companies have an unstandardised approach to unique medical problems, resulting in increased responsibility for the attending surgeon who may be ill equipped to deal with poorly researched aviation medicine.

Bovine tuberculosis in cattle and badgers in localized culling areas.

Bovine tuberculosis (TB) is a zoonotic disease that can have serious consequences for cattle farming and, potentially, for public health. In Britain, failure to control bovine TB has been linked to persistent infection of European badger (Meles meles) populations. However, culling of badgers in the vicinity of recent TB outbreaks in cattle has failed to reduce the overall incidence of cattle TB. Using data from a large-scale study conducted in 1998-2005, we show that badgers collected on such localized culls had elevated prevalence of Mycobacterium bovis, the causative agent of bovine TB, suggesting that infections in cattle and badgers were indeed associated. Moreover, there was a high degree of similarity in the M. bovis strain types isolated from cattle and associated badgers. This similarity between strain types appeared to be unaffected by time lags between the detection of infection in cattle and culling of badgers, or by the presence of purchased cattle that might have acquired infection elsewhere. However, localized culling appeared to prompt an increase in the prevalence of M. bovis infection in badgers, probably by disrupting ranging and territorial behavior and hence increasing intraspecific transmission rates. This elevated prevalence among badgers could offset the benefits, for cattle, of reduced badger densities and may help to explain the failure of localized culling to reduce cattle TB incidence.

Geopolymerisation of silt generated from construction and demolition waste washing plants.

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (<63mum) silt particles that is classified as inert waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.

Influences of chemical activators on incinerator bottom ash.

This research has applied different chemical activators to mechanically and thermally treated fine fraction (<14 mm) of incinerator bottom ash (IBA), in order to investigate the influences of chemical activators on this new pozzolanic material. IBA has been milled and thermally treated at 800 degrees C (TIBA). The TIBA produced was blended with Ca(OH)(2) and evaluated for setting time, reactivity and compressive strength after the addition of 0.0565 mole of Na(2)SO(4), K(2)SO(4), Na(2)CO(3), K(2)CO(3), NaOH, KOH and CaCl(2) into 100g of binder (TIBA+Ca(OH)(2)). The microstructures of activated IBA and hydrated samples have been characterized by X-ray diffraction (XRD) and thermogravimetry (TG) analysis. Thermal treatment is found to produce gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)) phases. The thermally treated IBA samples are significantly more reactive than the milled IBA. The addition of Na(2)CO(3) can increase the compressive strength and calcium hydroxide consumption at 28-day curing ages. However, the addition of Na(2)SO(4), K(2)SO(4), K(2)CO(3), NaOH and KOH reduces the strength and hydration reaction. Moreover, these chemicals produce more porous samples due to increased generation of hydrogen gas. The addition of CaCl(2) has a negative effect on the hydration of TIBA samples. Calcium aluminium oxide carbonate sulphide hydrate (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33)(H(2)O)(11)) is the main hydration product in the samples with activated IBA, except for the sample containing CaCl(2).

Solidification/stabilisation of air pollution control residues using Portland cement: Physical properties and chloride leaching.

Portland cement (CEMI) was used to solidify air pollution control (APC) residues from an energy-from-waste plant burning municipal solid waste. APC residue/CEMI mixes were prepared with CEMI additions ranging from 0 to 50 weight% (wt%) of total dry mass and water/solids ratios between 0.40 and 0.80. Isothermal conduction calorimetry was used to assess the effect of APC residues on the hydration of CEMI. Although up to 30wt% additions of APC residues accelerated CEMI hydration, the total heat of hydration during the initial 98h was significantly reduced. Higher levels of APC residues severely inhibited CEMI hydration. The consistence, setting time, compressive strength, porosity and chloride leaching characteristics of the solidified products were determined. As might be expected, increasing the CEMI addition and reducing the water content resulted in increased compressive strengths. All mixes achieved compressive strengths greater than 1MPa at 7 and 28days but only 50wt% samples did not show significant strength reduction when tested after immersion in water. Monolithic leaching tests indicated low physical immobilisation of chloride in the CEMI solidified APC residues, with chloride leaching in excess of relevant UK landfill waste acceptance criteria (WAC). The results of this study show that greater than 50% CEMI additions would be required to effectively treat APC residues to meet current WAC limits.

Thermal plasma technology for the treatment of wastes: a critical review.

This review describes the current status of waste treatment using thermal plasma technology. A comprehensive analysis of the available scientific and technical literature on waste plasma treatment is presented, including the treatment of a variety of hazardous wastes, such as residues from municipal solid waste incineration, slag and dust from steel production, asbestos-containing wastes, health care wastes and organic liquid wastes. The principles of thermal plasma generation and the technologies available are outlined, together with potential applications for plasma vitrified products. There have been continued advances in the application of plasma technology for waste treatment, and this is now a viable alternative to other potential treatment/disposal options. Regulatory, economic and socio-political drivers are promoting adoption of advanced thermal conversion techniques such as thermal plasma technology and these are expected to become increasingly commercially viable in the future.

Characterization of alkali-activated thermally treated incinerator bottom ash.

The fine fraction (<14 mm) of incinerator bottom ash (IBA) obtained from a UK energy from waste plant has been milled and thermally treated at 600, 700, 800 and 880 degrees C. Treated materials have been activated with Ca(OH)(2) (10 wt%) and the setting times and compressive strengths at different curing times measured. In addition to decomposition of CaCO(3) to CaO, thermal treatment increases the content of gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)). Thermally treated samples were significantly more reactive than milled IBA and heating to 700 degrees C produced a material which rapidly set. Silica, gehlenite and wollastonite were the main crystalline phases present in hydrated samples and a mixed sulphate-carbonate AFm-type phase (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33).11H(2)O) formed. Significant volumes of gas were generated during curing and this produced a macro-porous microstructure that limited strength to 2.8 MPa. The new materials may have potential for use as controlled low-strength materials.

Plasma treatment of air pollution control residues.

Air pollution control (APC) residues from waste incineration have been blended with silica and alumina and the mix melted using DC plasma arc technology. The chemical composition of the fully amorphous homogeneous glass formed has been determined. Waste acceptance criteria compliance leach testing demonstrates that the APC residue derived glass releases only trace levels of heavy metals (Pb (<0.007mg/kg) and Zn (0.02mg/kg)) and Cl(-) (0.2mg/kg). These are significantly below the limit values for disposal to inert landfill. It is concluded that plasma treatment of APC residues can produce an inert glass that may have potential to be used either in bulk civil engineering applications or in the production of higher value glass-ceramic products.

Solid waste management in Abuja, Nigeria.

The new city of Abuja provided an opportunity to avoid some of the environmental problems associated with other major cities in Africa. The current status of solid waste management in Abuja has been reviewed and recommendations for improvements are made. The existing solid waste management system is affected by unfavourable economic, institutional, legislative, technical and operational constraints. A reliable waste collection service is needed and waste collection vehicles need to be appropriate to local conditions. More vehicles are required to cope with increasing waste generation. Wastes need to be sorted at source as much as possible, to reduce the amount requiring disposal. Co-operation among communities, the informal sector, the formal waste collectors and the authorities is necessary if recycling rates are to increase. Markets for recycled materials need to be encouraged. Despite recent improvements in the operation of the existing dumpsite, a properly sited engineered landfill should be constructed with operation contracted to the private sector. Wastes dumped along roads, underneath bridges, in culverts and in drainage channels need to be cleared. Small-scale waste composting plants could promote employment, income generation and poverty alleviation. Enforcement of waste management legislation and a proper policy and planning framework for waste management are required. Unauthorized use of land must be controlled by enforcing relevant clauses in development guidelines. Accurate population data is necessary so that waste management systems and infrastructure can be properly planned. Funding and affordability remain major constraints and challenges.