Tracing the fate of microplastic in wastewater treatment plant: A multi-stage analysis of treatment units and sludge.

Microplastic (MP) pollution is ubiquitous in the environment presenting a global problem for both scientists and the general public. One of the major pathways of MPs entering the natural environment is through wastewater treatment plants (WWTPs). Once MPs reach the natural environment, they are posing threat to aquatic ecosystems and public health. The aim of this study is to investigate the concentration, morphology, and composition of MPs in different treatment units of a WWTP. Sampling included different points across WWTP in the water and sludge lines. Pre-treatment of the samples consists of advanced Fenton oxidation, and alkaline and enzymatic digestion followed by density separation. Once the particles were isolated, their morphology and size were studied using a stereoscopic and optical microscope followed by final confirmation with ATR-FTIR and micro-FTIR spectroscopy. Microplastic particle concentrations exhibit significant reductions as water undergoes treatment in the WWTP. For summer sampling, concentrations decreased from 351 MP/L (influent) to 35 MP/L (primary clarifier), 32 MP/L (biological reactor), and 13 MP/L (2.3 MP/L) (secondary clarifier). Similarly, winter sampling showed reductions from 403 MP/L (influent) to 159 MP/L (primary clarifier), 178 MP/L (biological reactor), and 26 MP/L (5.6 MP/L) (secondary clarifier). Removal efficiency of WWTP is high and exceeds 96%. The most abundant morphology is fibers followed by fragments and films. Polymers such as PE, synthetic cellulose, PP, PVC, PE-PP, PEEA, PA, acrylamide, and PES are widely detected in different units of WWTP. The number of MPs that are avoided from being emitted into the environment through direct water discharge was estimated to be 9.1 × 1012 MP/year. Removed MPs tend to accumulate in the sludge that is used for agricultural purposes although it should be managed as waste properly, avoiding the transition of MPs pollutants to terrestrial ecosystems adding to the number of MPs that will inevitably end up in receiving water bodies through direct WWTP effluent discharge that was set in 5.1 × 1010 MP/year in the studied WWTP.

Mapping of heavy metal contamination associated with microplastics marine debris - A case study: Dubai, UAE.

Microplastics (MPs) are ubiquitously detected in the environment. The adverse impact of microplastics on marine life is well documented. Previous research has shown that MPs can adsorb heavy metals, however, this fact has not been investigated along the coast of Dubai, UAE. Elemental composition of MPs debris was determined using X-ray fluorescence spectroscopic (XRF) analysis. The analyzed MPs were extracted from 80 sediment samples collected from the wrack lines of 16 Dubai, UAE beaches. A total of 480 MPs pieces extracted from the samples were analyzed in order to detect heavy metals. The polymer composition was previously confirmed by FTIR spectroscopy, showing that polyethylene (PE) and polypropylene (PP) were the most abundant MPs. 14 heavy metals were identified in the samples: Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Pb, Ce, Pr, Nd, Pd, and Co with different concentrations. Five of them (Cr, Ni, Cu, Zn, and Pb) are priority pollutants according to EPA. Their average concentrations in oxide form were Cr2O3 (2.96 %), NiO (0.32 %), CuO (0.45 %), ZnO (0.56 %), and PbO (1.49 %).

Screening of microplastics in water and sludge lines of a drinking water treatment plant in Catalonia, Spain.

Microplastics (MPs) are emerging pollutants detected everywhere in the environment, with the potential to harm living organisms. The present study investigated the concentration, morphology, and composition of MPs, between 20 µm and 5 mm, in a drinking water treatment plant (DWTP) located close to Barcelona (Catalonia, NE Spain). The sampling included different units of the DWTP, from influent to effluent as well as sludge line. Sampling strategy, filtration, allows sampling of large volumes of water avoiding sample contamination, and during 8 h in order to increase the representativeness of MPs collected. The pre-treatment of the samples consisted of advanced oxidation with Fenton's reagent and hydrogen peroxide, followed by density separation of the particles with zinc chloride solution. Visual identification was performed with an optical and stereoscopic microscope with final Fourier-transform infrared spectroscopic (FTIR) confirmation. MPs were found in all DWTP samples, with concentrations from 4.23 ± 1.26 MPs/L to 0.075 ± 0.019 MPs/L in the influent and effluent of the plant, respectively. The overall removal efficiency of the plant was 98.3%. The most dominant morphology was fibers followed by fragments and films. Twenty-two different polymer types were identified and synthetic cellulose, polyester, polyamide, polypropylene, polyethylene, polyurethane, and polyacrylonitrile were the most common. Although MPs could be incorporated from the distribution network, MPs intake from drinking water from this DWTP was not an important route compared to fish and seafood ingestion.