RESUMEN
In this study, 4-phenylthiazol-2-yl-(phenylhydrazono) acetonitrile (PTPA) azo dye was synthesized and studied from optical and electrical point of view. The tautomerization phenomenon of the PTPA dye was clarified using one-dimensional (1D) and two-dimensional (2D) nuclear magnetic resonance (1HNMR and 13C NMR), absorbance (UV-Vis), emission, and Fourier transform infrared spectroscopy (FT-IR). X-ray diffraction (XRD) evaluations were indicated that PTPA in powder and thin films crystallizes in a monoclinic system structure with nonstructural characteristics. Spectrophotometric measurements of absorbance A (λ), transmittance T (λ) and reflectance R (λ) at normal incidence light in the wavelength range 200-2500 nm were used to determine the optical band gap, extinction coefficient, k and refractive index, n. Also, non-linear optical parameters such as the third order non-linear susceptibility, χ(3) and nonlinear refractive index, n(2) of PTPA have revealed an awe-inspiring switching behavior, implying the possibility of using PTPA in optical switching systems. Finally, the electrical conductivity of the PTPA was shown to increase with rising temperature, indicating that it is a typical organic semiconductor. Mott's parameters were determined and discussed at low temperatures. Thus, PTPA is a promising organic semiconductor with broad utility potential in organic electronics such as organic light-emitting diodes (OLEDs).
RESUMEN
Metallic lithium (Li) anode batteries have attracted considerable attention due to their high energy density value. However, metallic Li is highly reactive and flammable, which makes Li anode batteries difficult to develop. In this work, for the first time, we report the synthesis of metallic Li-embedded carbon nanocomposites for easy and safe handling by a scalable ion beam-based method. We found that vertically standing conical Li-C nanocomposite (Li-C NC), sometimes with a nanofiber on top, can be grown on a graphite foil commonly used for the anodes of lithium-ion batteries. Metallic Li embedded inside the carbon matrix was found to be highly stable under ambient conditions, making transmission electron microscopy (TEM) characterization possible without any sophisticated inert gas-based sample fabrication apparatus. The developed ion beam-based fabrication technique was also extendable to the synthesis of stable Li-C NC films under ambient conditions. In fact, no significant loss of crystallinity or change in morphology of the Li-C film was observed when subjected to heating at 300 °C for 10 min. Thus, these ion-induced Li-C nanocomposites are concluded to be interesting as electrode materials for future Li-air batteries.
RESUMEN
Graphitized carbon including graphene has recently become one of the most investigated advanced materials for future device applications, but a prerequisite for broadening its range of applications is to lower its growth temperature. Here we report a great decrease in graphitization temperature using the well-known catalyst Ni. Amorphous carbon films with Ni nanoparticles (NPs) were deposited, using a simple one-step magnetron sputtering method, onto microgrids and a SiO2/Si substrate for transmission electron microscopy (TEM) and Raman spectroscopy analyses, respectively. The amorphous carbon surroundings and locations between the Ni NPs started to become graphitized during the film deposition even at room temperature (RT) and 50 °C. The graphitization was confirmed by both high-resolution TEM (HR-TEM) and Raman 2D peak analyses. The increase in the relative amount of Ni in the amorphous carbon film led to the partial oxidation of the larger Ni NPs, resulting in less graphitization even at an elevated deposition temperature. Based on the detailed HR-TEM analyses, a decreased oxidation of NPs and enhanced solubility of carbon into Ni NPs were believed to be key for achieving low-temperature graphitization.
RESUMEN
For the fabrication of graphene-based nano-scale interconnects, precise control over their position and proper nanoscale soldering are essential. In this work, we report the Joule heat-induced conversion of amorphous carbon to graphene in an in situ TEM setup, using Mo as a catalyst. The catalytic role of Mo during graphene formation has been less explored compared to other metals like Cu or Ni. Compared to metals like Cu, Mo is less subject to electromigration and brittleness, making it suitable for high-temperature electronics. We found that during the electromigration of Mo, amorphous carbon nanofibers (CNFs) can be converted to highly crystalline few-layered graphene. It was also found that during the graphene formation process, agglomerated Mo particles can be effectively channeled to the end of graphene by voltage-driven electromigration. An agglomerated Mo particle between the probe and graphene acted as a soldering agent, providing the prospect of the further exploration of Mo as a nanoscale soldering material. This work explores the double role of Mo: as a catalyst for graphene synthesis and as a soldering material.
RESUMEN
The knowledge of radioactivity content in various radionuclides in building materials plays an important role in health physics; therefore, we measured the amount of naturally occurring radionuclides in building material (sand, granite, marble, and limestone) samples of different grain sizes by using NaI (Tl) and MCA1024 gamma-ray spectrometers. Data analyses were performed to determine 226Ra, 232Th, and 4°K activity concentrations. The results revealed an inverse relationship between activity concentration and grain size of the samples. The radium equivalent activity (Raeq), representative level index I, and annual absorbed dose rate were calculated.
