Gelatin methacryloyl as environment for chondrocytes and cell delivery to superficial cartilage defects.

Cartilage damage typically starts at its surface, either due to wear or trauma. Treatment of these superficial defects is important in preventing degradation and osteoarthritis. Biomaterials currently used for deep cartilage defects lack appropriate properties for this application. Therefore, we investigated photo-crosslinked gelatin methacryloyl (gelMA) as a candidate for treatment of surface defects. It allows for liquid application, filling of surface defects and forming a protective layer after UV-crosslinking, thereby keeping therapeutic cells in place. gelMA and photo-initiator lithium phenyl-2,4,6-trimethyl-benzoylphosphinate (Li-TPO) concentration were optimized for application as a carrier to create a favorable environment for human articular chondrocytes (hAC). Primary hAC were used in passages 3 and 5, encapsulated into two different gelMA concentrations (7.5 wt% (soft) and 10 wt% (stiff)) and cultivated for 3 weeks with TGF-ß3 (0, 1 and 10 ng/mL). Higher TGF-ß3 concentrations induced spherical cell morphology independent of gelMA stiffness, while low TGF-ß3 concentrations only induced rounded morphology in stiff gelMA. Gene expression did not vary across gel stiffnesses. As a functional model gelMA was loaded with two different cell types (hAC and/or human adipose-derived stem cells [ASC/TERT1]) and applied to human osteochondral osteoarthritic plugs. GelMA attached to the cartilage, smoothened the surface and retained cells in place. Resistance against shear forces was tested using a tribometer, simulating normal human gait and revealing maintained cell viability. In conclusion gelMA is a versatile, biocompatible material with good bonding capabilities to cartilage matrix, allowing sealing and smoothening of superficial cartilage defects while simultaneously delivering therapeutic cells for tissue regeneration.

Autonomous spheroid formation by culture plate compartmentation.

Scaffold-free 3D cell cultures (e.g. pellet cultures) are widely used in medical science, including cartilage regeneration. Their drawbacks are high time/reagent consumption and lack of early readout parameters. While optimisation was achieved by automation or simplified spheroid generation, most culture systems remain expensive or require tedious procedures. The aim of this study was to establish a system for resource efficient spheroid generation with additional early readout parameters. This was achieved by a new approach for spheroid generation via self-assembly from monolayer via compartmentation of cell culture surfaces utilising laser engraving (grid plates). The compartmentation triggered contraction and rolling up of the cell monolayer, finishing in condensation into a spheroid in human adipose-derived stem cell (ASC/TERT1) and human articular chondrocytes (hACs)-ASC/TERT1 co-cultures, when cultivated on grid plates under chondrogenic conditions. Plates with 1 and 3 mm grid size yielded stable diameters (about 140µm and 300µm, respectively). ASC/TERT1 spheroids fully formed within 3 weeks while co-cultures took 1-2 weeks, forming significantly faster with increasing hAC ratio (p< 0.05 and 0.01 for 1:1 and 1:4 ASC/TERT1:hAC ratio, respectively). Co-cultures showed slightly lower spheroid diameters, due to earlier spheroid formation and incomplete monolayer formation. However, this was associated with a more homogeneous matrix distribution in the co-culture. Both showed differentiation capacity comparable to standard pellet culture in (immune-)histochemistry and RT-qPCR. To assess usability for cartilage repair, spheroids were embedded into a hydrogel (fibrin), yielding cellular outgrowth and matrix deposition, which was especially pronounced in co-cultures. The herein presented novel cell culture system is not only a promising tool for autonomous spheroid generation with the potential of experimental and clinical application in tissue engineering, but also for the generation of 'building blocks' for subsequential biofabrication strategies such as bioprinting.

Functionalization of bacterial cellulose wound dressings with the antimicrobial peptide ε-poly-L-Lysine.

Wound dressings based on bacterial cellulose (BC) can form a soft and conformable protective layer that can stimulate wound healing while preventing bacteria from entering the wound. Bacteria already present in the wound can, however, thrive in the moist environment created by the BC dressing which can aggravate the healing process. Possibilities to render the BC antimicrobial without affecting the beneficial structural and mechanical properties of the material would hence be highly attractive. Here we present methods for functionalization of BC with ε-poly-L-Lysine (ε-PLL), a non-toxic biopolymer with broad-spectrum antimicrobial activity. Low molecular weight ε-PLL was cross-linked in pristine BC membranes and to carboxymethyl cellulose functionalized BC using carbodiimide chemistry. The functionalization of BC with ε-PLL inhibited growth of S. epidermidis on the membranes but did not affect the cytocompatibility to cultured human fibroblasts as compared to native BC. The functionalization had no significant effects on the nanofibrous structure and mechanical properties of the BC. The possibility to functionalize BC with ε-PLL is a promising, green and versatile approach to improve the performance of BC in wound care and other biomedical applications.