Microdosimetry of an accelerator based thermal neutron field for Boron Neutron Capture Therapy.

The MUNES project (MUltidisciplinary NEutron Source) aims at the realization of an intense accelerator-based source of thermal neutrons, suitable for Boron Neutron Capture Therapy (BNCT). This exploits the interaction of 5 MeV protons onto a beryllium target, producing a fast neutron spectrum, which is moderated to the thermal range by a large assembly made of a Polytetrafluoroethylene (PTFE) tank filled with heavy water, surrounded by graphite blocks. The thermal neutron field is extracted through a bismuth beam port. The microdosimetric characterization of this field was performed using a cylindrical avalanche-confinement Tissue Equivalent Proportional Counter (TEPC) equipped with interchangeable cathode walls, positioned in front of the beam port. Measurements were taken both with a boron-doped wall and with an undoped one. The comparison of the two microdosimetric distributions allows to distinguish the relative dose contribution due to alpha particles and lithium ions from the BNC reaction from that of photons and other particles from neutron interactions on the cathode walls. The Relative Biological Effectiveness (RBE) was also calculated from the convolution of the measured spectra with a biological weighting function. This paper describes the experimental microdosimetric approach and the results of measurements with a boron-loaded cathode performed for the first time at an accelerator-based BNCT source.

Commissioning of high current H+/D+ ion beams for the prototype accelerator of the International Fusion Materials Irradiation Facility.

The Linear IFMIF (International Fusion Materials Irradiation Facility) Prototype Accelerator (LIPAc) is aiming at demonstrating the low energy section of a 40 MeV/125 mA IFMIF deuteron accelerator up to 9 MeV with a full beam current in cw operation. For such a high-power beam, the LIPAc injector is required to produce a 100 keV D+ beam with 140 mA and match it for injection into the Radio Frequency Quadrupole (RFQ) accelerator. The injector is designed by CEA-Saclay based on the high intensity light ion source (SILHI). In 2019, the commissioning of the RFQ to demonstrate the D+ beam acceleration at a low duty cycle (0.1%) was conducted. A nominal beam current of 125 mA D+ beam was accelerated up to 5 MeV through the RFQ successfully. The LIPAc injector fully satisfied the requirements for RFQ beam commissioning at the pulse mode.

First experiments with the negative ion source NIO1.

Neutral Beam Injectors (NBIs), which need to be strongly optimized in the perspective of DEMO reactor, request a thorough understanding of the negative ion source used and of the multi-beamlet optics. A relatively compact radio frequency (rf) ion source, named NIO1 (Negative Ion Optimization 1), with 9 beam apertures for a total H(-) current of 130 mA, 60 kV acceleration voltage, was installed at Consorzio RFX, including a high voltage deck and an X-ray shield, to provide a test bench for source optimizations for activities in support to the ITER NBI test facility. NIO1 status and plasma experiments both with air and with hydrogen as filling gas are described. Transition from a weak plasma to an inductively coupled plasma is clearly evident for the former gas and may be triggered by rising the rf power (over 0.5 kW) at low pressure (equal or below 2 Pa). Transition in hydrogen plasma requires more rf power (over 1.5 kW).

Installation of a versatile multiaperture negative ion source.

Neutral Beam Injectors (NBI), which need to be strongly optimized in the perspective of DEMO reactor, request a thorough understanding of the negative ion source used and of the multi-beamlet optics. A relatively compact RF ion source, named NIO1 (Negative Ion Optimization 1), with 9 beam apertures for a total H(-) current of 130 mA, 60 kV acceleration voltage, is being installed at Padua, in Consorzio RFX, to provide a test bench for source optimizations in the framework of the accompanying activities in support to the ITER NBI test facility. NIO1 construction and status of the overall installation, including a high voltage deck and an optical cavity ring down spectrometer are here summarized and reported. Plasma and low voltage beam operations are discussed. Development of a sampling beam calorimeter (with small sampling holes, and a segmented cooling circuit) is also discussed.

Enhancement of SPES source performances.

Installation of SPES source at LNL was finished in July 2006 and the first beam was extracted in September 2006. Commissioning results confirmed very good performance of the extracted current density. Conversely, source reliability was very poor due to glow-discharge phenomena, which were caused by the ion source axial magnetic field protruding in the high-voltage column. This problem was fixed by changing the stainless steel plasma electrode support with a ferromagnetic one. This new configuration required us to recalculate ion source solenoids positions and fields in order to recover the correct resonance pattern. Details on magnetic simulations and experimental results of high voltage column shielding are presented.