RESUMEN
Currently, fluidic control in microdevices is mainly achieved either by external pumps and valves, which are expensive and bulky, or by valves integrated in the chip. Numerous types of internal valves or actuation methods have been proposed, but they generally impose difficult compromises between performance and fabrication complexity. We propose here a new paradigm for actuation in microfluidic devices based on rigid or semi-rigid walls with transversal dimensions of hundreds of micrometres that are able to slide within a microfluidic chip and to intersect microchannels with hand-driven or translation stage-based actuation. With this new concept for reconfigurable microfluidics, the implementation of a wide range of functionalities was facilitated and allowed for no or limited dead volume, low cost and low footprint. We demonstrate here several fluidic operations, including on/off or switch valving, where channels are blocked or reconfigured depending on the sliding wall geometry. The valves sustain pressures up to 30 kPa. Pumping and reversible compartmentalisation of large microfluidic chambers were also demonstrated. This last possibility was applied to a "4D" migration assay of dendritic cells in a collagen gel. Finally, sliding walls containing a hydrogel-based membrane were developed and used to concentrate, purify and transport biomolecules from one channel to another, such functionality involving complex fluidic transport patterns not possible in earlier microfluidic devices. Overall, this toolbox is compatible with "soft lithography" technology, allowing easy implementation within usual fabrication workflows for polydimethylsiloxane chips. This new technology opens the route to a variety of microfluidic applications, with a focus on simple, hand-driven devices for point-of-care or biological laboratories with low or limited equipment and resources.
RESUMEN
An original method of monolith impregnation in microsystem for the analysis of radionuclides in nitric acid is reported. Three microcolumns made of monolith poly(AMA-co-EDMA) were impregnated in COC microsystems. The robustness of the microsystems in nitric acid media until 8 M was demonstrated. High exchange capacity and affinity for tetravalent and hexavalent actinides in concentrated nitric media were obtained. The retention characteristics of the microcolumns impregnated by TBP, TBP-CMPO and DAAP were compared with those of the equivalent commercial particulate resins TBP™, TRU™ and UTEVA™ respectively. The separation of U, Th and Eu was validated in a classical microsystem and a procedure is proposed in a centrifugal microsystem.
RESUMEN
Volume is an important parameter regarding physiological and pathological characteristics of neurons at different time scales. Neurons are quite unique cells regarding their extended ramified morphologies and consequently raise several methodological challenges for volume measurement. In the particular case of in vitro neuronal growth, the chosen methodology should include sub-micrometric axial resolution combined with full-field observation on time scales from minutes to hours or days. Unlike other methods like cell shape reconstruction using confocal imaging, electrically-based measurements or Atomic Force Microscopy, the recently developed Fluorescence eXclusion method (FXm) has the potential to fulfill these challenges. However, although being simple in its principle, implementation of a high-resolution FXm for neurons requires multiple adjustments and a dedicated methodology. We present here a method based on the combination of fluorescence exclusion, low-roughness multi-compartments microfluidic devices, and finally micropatterning to achieve in vitro measurements of local neuronal volume. The high resolution provided by the device allowed us to measure the local volume of neuronal processes (neurites) and the volume of some specific structures involved in neuronal growth, such as growth cones (GCs).
Asunto(s)
Fluorescencia , Dispositivos Laboratorio en un Chip/estadística & datos numéricos , Neuronas/fisiología , Animales , Humanos , RatonesRESUMEN
The use of a centrifugal microfluidic platform is an alternative to classical chromatographic procedures for radiochemistry. An ion-exchange support with respect to the in situ light-addressable process of elaboration is specifically designed to be incorporated as a radiochemical sample preparation module in centrifugal microsystem devices. This paper presents a systematic study of the synthesis of the polymeric porous monolith poly(ethylene glycol methacrylate-co-allyl methacrylate) used as a solid-phase support and the versatile and robust photografting process of the monolith based on thiol-ene click chemistry. The polymerization reaction is investigated, varying the formulation of the polymerisable mixture. The robustness of the stationary phase was tested in concentrated nitric acid. Thanks to their unique "easy-to-use" features, centrifugal microfluidic platforms are potential successful candidates for the downscaling of chromatographic separation of radioactive samples (automation, multiplexing, easy integration in glove-boxes environment, and low cost of maintenance).
RESUMEN
The nanofabrication of a nanomachined holed structure localized on the free end of a microcantilever is here presented, as a new tool to design micro-resonators with enhanced mass sensitivity. The proposed method allows both for the reduction of the sensor oscillating mass and the increment of the resonance frequency, without decreasing the active surface of the device. A theoretical analysis based on the Rayleigh method was developed to predict resonance frequency, effective mass, and effective stiffness of nanomachined holed microresonators. Analytical results were checked by Finite Element simulations, confirming an increase of the theoretical mass sensitivity up to 250%, without altering other figures of merit. The nanomachined holed resonators were vibrationally characterized, and their Q-factor resulted comparable with solid microcantilevers with same planar dimensions.
RESUMEN
In this work a polymer lab-on-a-chip (LOC), fabricated through MEMS technology, was employed to execute a genetic protocol for the Single Nucleotide Polymorphisms (SNPs) detection. The LOC was made in Poly (methyl methacrylate) (PMMA) and has two levels: the lower one for the insertion and mixing of the reagents, the upper one for the interfacing with the DNA microarray chip. The hereditary hearing loss was chosen as case of study, since the demand for testing such a particular disorder is high and genetics behind the condition is quite clear. The Arrayed Primer EXtension (APEX) genetic protocol was implemented on the LOC to analyze the SNPs. A low density (for detection of up to 10 mutations) and a high density microarray chips (for detection of 245 mutations in 12 genes), containing the primers for the extension, were employed to carry out the APEX reaction on the LOC. Both the microarray chips provide a signal to noise ratio and efficiency comparable with a detection obtained in a conventional protocol in standard conditions. Moreover, significant reduction of the employed PCR volume (from 30 µL to 10 µL) was obtained using the low density chip.
Asunto(s)
Cartilla de ADN/química , Dispositivos Laboratorio en un Chip , Análisis de Secuencia por Matrices de Oligonucleótidos/instrumentación , Análisis de Secuencia por Matrices de Oligonucleótidos/métodos , Polimorfismo de Nucleótido Simple , HumanosRESUMEN
To date control strategies in detecting anabolic agents for promoting growth of food producing animals are mainly related to screening techniques based on immunochemical and physiochemical methods, whose major limit is represented by relative low analytical sensitivity. As a consequence, consumers are currently exposed to molecules with potential carcinogenic effects such as 17ß-estradiol, the most powerful substance with estrogenic effect. Therefore, high analytical sensitivity screening and confirmatory methods are required, coupling easiness of use and efficiency. We here report on the immunodetection of 17ß-estradiol in serum by antibody-immobilized microcantilever resonators, an innovative biosensing platform able to quantify an adsorbed target mass (such as cells, nucleic acids, biomolecules, etc.) thanks to a shift in resonance frequency. Our tool based on microcantilever resonator arrays has shown to be capable of discriminating treated and untreated animals, showing the ability of detecting traces of 17ß-estradiol in serum at concentrations lower than the present accepted physiological serum concentration threshold value (40 ppt) and commercial ELISA tests (25 ppt). The method exhibits a limit of detection of 20 ppt and a limited cross-reactivity with high concentrations (10 ppb) of similar molecules (testosterone).
Asunto(s)
Técnicas Biosensibles/instrumentación , Estradiol/sangre , Inmunoensayo/instrumentación , Sistemas Microelectromecánicos/instrumentación , Microquímica/instrumentación , Diseño de Equipo , Análisis de Falla de Equipo , Reproducibilidad de los Resultados , Sensibilidad y EspecificidadRESUMEN
Mycotoxins, such as aflatoxins and ochratoxin A, are presently considered as the most important chronic dietary risk factor, more than food additives or pesticide residues. Therefore, the serious health and economic consequences of mycotoxin contamination have created the need for rapid, sensitive, and reliable techniques to detect such dangerous molecules within foodstuffs. We here report on the development of an innovative immunosensing method for mycotoxin detection, based on antibody-immobilized microcantilever resonators, a promising label free biosensing technique. A considerable part of the work is devoted to show the effect on microcantilever resonance frequency of the composition of the incubation buffer, as well as of the washing and drying procedure. We show the feasibility of using microcantilever resonator arrays to effectively identify total aflatoxins and ochratoxin A, at low concentrations (3 ng/mL and less than 6 ng/mL, respectively), with relatively low uncertainty (about 10%) and good reproducibility for the same target concentration. Furthermore, the developed immunosensing method shows a limited cross-reactivity to different mycotoxins, paving the way to a highly specific technique, able to identify different mycotoxins in the sample. To our knowledge, this work represents the first example in literature of successfully immunodetection of low concentrations of multiple mycotoxins by microcantilever resonator arrays.
Asunto(s)
Técnicas Biosensibles/instrumentación , Inmunoensayo/instrumentación , Sistemas Microelectromecánicos/instrumentación , Micotoxinas/análisis , Ocratoxinas/análisis , Diseño de Equipo , Análisis de Falla de Equipo , Reproducibilidad de los Resultados , Sensibilidad y EspecificidadRESUMEN
Miniaturization of analytical procedures has a significant impact on diagnostic testing since it provides several advantages such as: reduced sample and reagent consumption, shorter analysis time and less sample handling. Lab-on-a-chip (LoC), usually silicon, glass, or silicon-glass, or polymer disposable cartridges, which are produced using techniques inherited from the microelectronics industry, could perform and integrate the operations needed to carry out biochemical analysis through the mechanical realization of a dedicated instrument. Analytical devices based on miniaturized platforms like LoC may provide an important contribution to the diagnosis of high prevalence and rare diseases. In this paper we review some of the uses of Lab-on-a-chip in the clinical diagnostics of immune-mediated diseases and we provide an overview of how specific applications of these technologies could improve and simplify several complex diagnostic procedures.
Asunto(s)
Enfermedades del Sistema Inmune/diagnóstico , Dispositivos Laboratorio en un Chip , Humanos , Enfermedades del Sistema Inmune/genética , Análisis de Secuencia por Matrices de Oligonucleótidos/instrumentaciónRESUMEN
Lab-on-chips (LOCs) are critical systems that have been introduced to speed up and reduce the cost of traditional, laborious and extensive analyses in biological and biomedical fields. These ambitious and challenging issues ask for multi-disciplinary competences that range from engineering to biology. Starting from the aim to integrate microarray technology and microfluidic devices, a complex multilevel analysis platform has been designed, fabricated and tested (All rights reserved-IT Patent number TO2009A000915). This LOC successfully manages to interface microfluidic channels with standard DNA microarray glass slides, in order to implement a complete biological protocol. Typical Micro Electro Mechanical Systems (MEMS) materials and process technologies were employed. A silicon/glass microfluidic chip and a Polydimethylsiloxane (PDMS) reaction chamber were fabricated and interfaced with a standard microarray glass slide. In order to have a high disposable system all micro-elements were passive and an external apparatus provided fluidic driving and thermal control. The major microfluidic and handling problems were investigated and innovative solutions were found. Finally, an entirely automated DNA hybridization protocol was successfully tested with a significant reduction in analysis time and reagent consumption with respect to a conventional protocol.
Asunto(s)
ADN/análisis , ADN/genética , Técnicas Analíticas Microfluídicas/instrumentación , Análisis de Secuencia por Matrices de Oligonucleótidos/instrumentación , Secuencia de Bases , Colorimetría , Dimetilpolisiloxanos/química , Vidrio/química , Humanos , Microtecnología , Hibridación de Ácido Nucleico , Reproducibilidad de los Resultados , Silicio/químicaRESUMEN
Microcantilever based oscillators have shown the possibility of highly sensitive label-free detection by allowing the transduction of a target mass into a resonant frequency shift. Most of such measurements were performed in air or vacuum environment, since immersion in liquid dramatically deteriorates the mechanical response of the sensor. Besides, the integration of microcantilever detection in a microfluidic platform appears a highly performing technological solution to exploit real time monitoring of biomolecular interactions, while limiting sample handling and promoting portability and automation of routine diagnostic tests (Point-Of-Care devices). In the present paper, we report on the realization and optimization of a microcantilever-based Lab-on-Chip, showing that microplates rather than microbeams exhibit largest mass sensitivity in liquid, while pirex rather than polymers represents the best choice for microfluidic channels. Maximum Q factor achieved was 140 (for fifth resonance mode of Pirex prototype), as our knowledge the highest value reported in literature for cantilever biosensors resonating in liquid environment without electronic feedback. Then, we proved the successfully detection of Angiopoietin-1 (a putative marker in tumor progression), showing that the related frequency shifts coming from non-specific interactions (negative controls) are roughly one order of magnitude lower than typical variations due to specific protein binding. Furthermore, we monitored the formation of antibody-antigen complex on MC surface in real-time. The proposed tool could be extremely useful for the comprehension of complex biological systems such as angiogenic machinery and cancer progression.
Asunto(s)
Técnicas Biosensibles/instrumentación , Técnicas Analíticas Microfluídicas/instrumentación , Angiopoyetina 1/análisis , Anticuerpos Inmovilizados , Reacciones Antígeno-Anticuerpo , Biomarcadores de Tumor/análisis , Técnicas Biosensibles/métodos , Técnicas Biosensibles/estadística & datos numéricos , Progresión de la Enfermedad , Diseño de Equipo , Humanos , Técnicas Analíticas Microfluídicas/métodos , Técnicas Analíticas Microfluídicas/estadística & datos numéricos , Neoplasias/irrigación sanguínea , Neoplasias/química , Neovascularización PatológicaRESUMEN
Microcantilever biosensors have been proposed in the last years as very sensitive mass detectors, but few works focused on the precision and specificity of such tools. We measured the repeatability and reproducibility of our cantilever-based system, proponing the combination of results coming from both the first and second mode of vibration. Then, we optimized two biodesigns (a receptor-based and an antibody-based) to the detection of Angiopoietin-1, a possible marker in tumor progression. The reported results show that our microcantilever-based system can detect Angiopoietin-1 masses of the order of few hundreds of picograms with less than 0.5% of relative uncertainty. We showed that the evaluation of the protein surface density (number of molecules per cm(2)) could reveal interesting features concerning the multimerization state of the targeted protein. We also performed negative controls (dipping the sample in PBS without proteins) and specificity tests (dipping the sample in PBS with a "false" antigen). The related frequency shifts coming from non-specific interactions were found to be at least one order of magnitude lower than typical variations due to specific protein binding. Thanks to its fine precision and optimal specificity, our microcantilever-based system can be successfully applied as a quantitative tool for systems biology studies such as the comprehension of angiogenic machinery and cancer progression.