Effects of the Amylose/Amylopectin Ratio of Starch on Borax-Crosslinked Hydrogels.

Herein, we simultaneously prepared borax-crosslinked starch-based hydrogels with enhanced mechanical properties and self-healing ability via a simple one-pot method. The focus of this work is to study the effects of the amylose/amylopectin ratio of starch on the grafting reactions and the performance of the resulting borax-crosslinked hydrogels. An increase in the amylose/ amylopectin ratio increased the gel fraction and grafting ratio but decreased the swelling ratio and pore diameter. Compared with hydrogels prepared from low-amylose starches, hydrogels prepared from high-amylose starches showed pronouncedly increased network strength, and the maximum storage modulus increased by 8.54 times because unbranched amylose offered more hydroxyl groups to form dynamic borate ester bonds with borate ions and intermolecular hydrogen bonds, leading to an enhanced crosslink density. In addition, all the hydrogels exhibited a uniformly interconnected network structure. Furthermore, owing to the dynamic borate ester bonds and hydrogen bonds, the hydrogel exhibited excellent recovery behavior under continuous step strain, and it also showed thermal responsiveness.

Innovative Approaches for Manufacturing Epoxy-Modified Wood and Cellulose Fiber Composites: A Comparison between Injection Molding and 3D Printing.

The current study focused on improving the properties of polylactic acid (PLA) for wider application in load-bearing scenarios. Various methods were explored to optimize the interaction between PLA and natural fibers, particularly wood fibers (WFs). Alkalized and epoxy-impregnated WFs were evaluated against untreated WFs and cellulose fibers in both injection molding (IM) and fused deposition modeling (FDM). FTIR analysis revealed the removal of hemicellulose and lignin in alkalized WFs and uniform epoxy curing. Addition of fibers reduced PLA's thermal stability while acting as nucleating agents. Additionally, fibers augmented the storage modulus of biocomposites, with alkalized fibers exhibiting the highest tensile modulus in IM. FDM samples with a 0° raster angle showed superior impact resistance compared to IM counterparts. Moreover, raster angle significantly influenced FDM biocomposite properties, enhancing the tensile strength and modulus of untreated WF and cellulose fibers at 0°. Although FDM did not produce alkalized WF samples, epoxy impregnation emerged as a promising method for enhancing PLA/WF composite mechanical properties in the IM process, offering valuable insights for composite material development.

Biodegradable PBAT/PLA blend films incorporated with turmeric and cinnamomum powder: A potential alternative for active food packaging.

Active packaging made from biodegradable polymers and natural additives appears as an ecological alternative. In addition to having antioxidant activity and enhancing food preservation, it allows mitigating the negative impacts caused by improper disposal. This study pursued to produce biodegradable films based on a polymer blend PBAT/PLA (Ecovio®) using the flat extrusion method. The films were prepared with the incorporation of 5 wt% of powdered turmeric or cinnamon as natural additives. The films obtained, and those reprocessed twice, were characterized in terms of colorimetric, UV light transmittance, water contact angle, water vapor permeability, morphology, mechanical properties, and antioxidant activity. Cinnamon reduced the UV light transmittance and made a surface more hydrophobic. Reprocessing led to greater elongation and maximum load, associated with increased dispersion and distribution, as evidenced in the morphological analysis. The films developed have significant potential for applications in active food packaging, with emphasis on cinnamon-additivated films.

Biobased 2,5-Bis(hydroxymethyl)furan as a Versatile Building Block for Sustainable Polymeric Materials.

Furanic polymers, currently mainly represented by polyethylene 2,5-furandicarboxylate (PEF), also known as polyethylene furanoate, have a fantastic potential to replace fossil-based polymers: for example, polyethylene terephthalate (PET). While 2,5-furandicarboxylic acid (FDCA), a precursor of PEF, and its derived polymers have been studied extensively, 2,5-bis(hydroxymethyl)furan (BHMF) has received relatively little attention so far. Similarly to FDCA, BHMF is a biobased platform chemical derived from renewable sources such as sugars. This review highlights different polymerization techniques for BHMF-based polyesters and addresses BHMF's relative instability during the synthesis of BHMF-derived polymers, including polycarbonates and polyurethanes. Furthermore, the degradability of furanic polyesters is discussed and BHMF's toxicity is briefly elaborated.

Robust Superamphiphilic Membrane with a Closed-Loop Life Cycle.

Oil-spill remediation is an international environmental challenge, and superamphiphilic membranes, as a promising solution, have recently drawn lots of attention. However, the robustness of the conventional membrane design is less satisfying under severe conditions during practical applications. Additionally, it is unavoidable for the membranes to face a series of foulants in their practical working environment, for example, algae and sand. These foulants will block the membrane, which leads to a new economic and environmental problem in terms of waste management at the end of their life. To address the aforementioned challenges, a new generation of superamphiphilic vitrimer epoxy resin membranes (SAVER) to separate oil and water efficiently is reported. Similar to classical epoxy resins, SAVER shows strong mechanical robustness and sustains exposure to aqua regia and sodium hydroxide solutions. Furthermore, the blocked membrane can be easily recovered when contaminated with mixed foulants by using dynamic transesterification reactions in the polymer network. The ease with which biobased SAVER can be manufactured, used, recycled, and re-used without losing value points to new directions in designing a closed-loop superamphiphilic membrane life cycle.

Stereolithographic 3D Printing with Renewable Acrylates.

The accessibility of cost-competitive renewable materials and their application in additive manufacturing is essential for an efficient biobased economy. We demonstrate the rapid prototyping of sustainable resins using a stereolithographic 3D printer. Resin formulation takes place by straightforward mixing of biobased acrylate monomers and oligomers with a photoinitiatior and optical absorber. Resin viscosity is controlled by the monomer to oligomer ratio and is determined as a function of shear rate by a rheometer with parallel plate geometry. A stereolithographic apparatus charged with the biobased resins is employed to produce complex shaped prototypes with high accuracy. The products require a post-treatment, including alcohol rinsing and UV irradiation, to ensure complete curing. The high feature resolution and excellent surface finishing of the prototypes is revealed by scanning electron microscopy.

Biobased Acrylate Photocurable Resin Formulation for Stereolithography 3D Printing.

To facilitate the ongoing transition toward a circular economy, the availability of renewable materials for additive manufacturing becomes increasingly important. Here, we report the successful fabrication of complex shaped prototypes from biobased acrylate photopolymer resins, employing a commercial stereolithography apparatus (SLA) 3D printer. Four distinct resins with a biobased content ranging from 34 to 67% have been developed. All formulations demonstrated adequate viscosity and were readily polymerizable by the UV-laser-based SLA process. Increasing the double-bond concentration within the resin results in stiff and thermally resilient 3D printed products. High-viscosity resins lead to high-resolution prototypes with a complex microarchitecture and excellent surface finishing, comparable to commercial nonrenewable resins. These advances can facilitate the wide application of biobased resins for construction of new sustainable products via stereolithographic 3D printing methods.