In this study, we present a comprehensive optimization framework employing the Multi-Objective Multi-Verse Optimization (MOMVO) algorithm for the optimal integration of Distributed Generations (DGs) and Capacitor Banks (CBs) into electrical distribution networks. Designed with the dual objectives of minimizing energy losses and voltage deviations, this framework significantly enhances the operational efficiency and reliability of the network. Rigorous simulations on the standard IEEE 33-bus and IEEE 69-bus test systems underscore the effectiveness of the MOMVO algorithm, demonstrating up to a 47% reduction in energy losses and up to a 55% improvement in voltage stability. Comparative analysis highlights MOMVO's superiority in terms of convergence speed and solution quality over leading algorithms such as the Multi-Objective Jellyfish Search (MOJS), Multi-Objective Flower Pollination Algorithm (MOFPA), and Multi-Objective Lichtenberg Algorithm (MOLA). The efficacy of the study is particularly evident in the identification of the best compromise solutions using MOMVO. For the IEEE 33 network, the application of MOMVO led to a significant 47.58% reduction in daily energy loss and enhanced voltage profile stability from 0.89 to 0.94 pu. Additionally, it realized a 36.97% decrease in the annual cost of energy losses, highlighting substantial economic benefits. For the larger IEEE 69 network, MOMVO achieved a remarkable 50.15% reduction in energy loss and improved voltage profiles from 0.89 to 0.93 pu, accompanied by a 47.59% reduction in the annual cost of energy losses. These results not only confirm the robustness of the MOMVO algorithm in optimizing technical and economic efficiencies but also underline the potential of advanced optimization techniques in facilitating the sustainable integration of renewable energy resources into existing power infrastructures. This research significantly contributes to the field of electrical distribution network optimization, paving the way for future advancements in renewable energy integration and optimization techniques for enhanced system efficiency, reliability, and sustainability.
This research discusses the solar and wind sourcesintegration in aremote location using hybrid power optimization approaches and a multi energy storage system with batteries and supercapacitors. The controllers in PV and wind turbine systems are used to efficiently operate maximum power point tracking (MPPT) algorithms, optimizing the overall system performance while minimizing stress on energy storage components. More specifically, on PV generator, the provided method integrating the Perturb & Observe (P&O) and Fuzzy Logic Control (FLC) methods. Meanwhile, for the wind turbine, the proposed approach combines the P&O and FLC methods. These hybrid MPPT strategies for photovoltaic (PV) and wind turbine aim to optimize its operation, taking advantage of the complementary features of the two methods. While the primary aim of these hybrid MPPT strategies is to optimize both PV and wind turbine, therefore minimizing stress on the storage system, they also aim to efficiently supply electricity to the load. For storage, in this isolated renewable energy system, batteries play a crucial role due to several specific benefits and reasons. Unfortunately, their energy density is still relatively lower compared to some other forms of energy storage. Moreover, they have a limited number of charge-discharge cycles before their capacity degrades significantly. Supercapacitors (SCs) provide significant advantages in certain applications, particularly those that need significant power density, quick charging and discharging, and long cycle life. However, their limitations, such as lower energy density and specific voltage requirements, make them most effective when combined with other storage technologies, as batteries. Furthermore, their advantages are enhanced, result a more dependable and cost-effective hybrid energy storage system (HESS). The paper introduces a novel algorithm for power management designed for an efficient control. Moreover, it focuses on managing storage systems to keep their state of charge (SOC) within defined range. The algorithm is simple and effective. Furthermore, it ensures the longevity of batteries and SCs while maximizing their performance. The results reveal that the suggested method successfully keeps the limits batteries and SCs state of charge (SOC). To show the significance of system design choices and the impact on the battery's SOC, which is crucial for the longevity and overall performance of the energy storage components, a comparison in of two systems have been made. A classical system with one storage (PV/wind turbine/batteries) and the proposed system with HESS (PV/wind turbine system with batteries). The results show that the suggested scenario investigated with both wind and solar resources appears to be the optimum solution for areas where the two resources are both significant and complementary. The balance between the two resources seems to contribute to less stress on storage components, potentially leading to a longer lifespan. An economical study has been made, using the Homer Pro software, to show the feasibility of the proposed system in the studied area.
This work designs and implements a single-stage rectifier-based RF energy harvesting device. This device integrates a receiving antenna and a rectifying circuit to convert ambient electromagnetic energy into useful DC power efficiently. The rectenna is carefully engineered with an optimal matching circuit, achieving high efficiency with a return loss of less than -10 dB. The design uses a practical model of the Schottky diode, where both RF and DC characteristics are derived through extensive experimental measurements. The results from both experiments and simulations confirm the effectiveness of the design, showing its proficiency in efficient RF energy harvesting under low-power conditions. The antenna produced operates in the wifi band with a gain close to 4 dBi and a bandwidth of 100 MHz. With a load resistance of 1600 Ω, the proposed device achieves an impressive RF-to-DC conversion efficiency of approximately 52% at a low incident power of -5 dBm. These findings highlight the potential and reliability of rectenna systems for practical and efficient RF energy harvesting applications. The study significantly contributes to our understanding of rectenna-based energy harvesting, providing valuable insights for future design considerations and applications in low-power RF systems.
The lifetime of power transformers is closely related to the insulating oil performance. This latter can degrade according to overheating, electric arcs, low or high energy discharges, etc. Such degradation can lead to transformer failures or breakdowns. Early detection of these problems is one of the most important steps to avoid such failures. More efficient diagnostic systems, such as artificial intelligence techniques, are recommended to overcome the limitations of the classical methods. This work deals with diagnosing the power transformer insulating oil by analysis of dissolved gases using new techniques. For this, we have proposed intelligent techniques based on Multilayer artificial neural networks (ANN). Thus, a multi-layer ANN-based model for fault detection is presented. To improve its classification rate, this one was optimized by a meta-heuristic technique as the particle swarm optimization (PSO) technique. Optimized ANNs have never been used in transformer insulating oil diagnostics so far. The robustness and effectiveness of the proposed model is demonstrated, and high accuracy is obtained.
This paper proposes an innovative approach to improve the performance of grid-connected photovoltaic (PV) systems operating in environments with variable atmospheric conditions. The dynamic nature of atmospheric parameters poses challenges for traditional control methods, leading to reduced PV system efficiency and reliability. To address this issue, we introduce a novel integration of fuzzy logic and sliding mode control methodologies. Fuzzy logic enables the PV system to effectively handle imprecise and uncertain atmospheric data, allowing for decision-making based on qualitative inputs and expert knowledge. Sliding mode control, known for its robustness against disturbances and uncertainties, ensures stability and responsiveness under varying atmospheric conditions. Through the integration of these methodologies, our proposed approach offers a comprehensive solution to the complexities posed by real-world atmospheric dynamics. We anticipate applications in grid-connected PV systems across various geographical locations and climates. By harnessing the synergistic benefits of fuzzy logic and sliding mode control, this approach promises to significantly enhance the performance and reliability of grid-connected PV systems in the presence of variable atmospheric conditions. On the grid side, both PSO (Particle Swarm Optimization) and GA (Genetic Algorithm) algorithms were employed to tune the current controller of the PI (Proportional-Integral) current controller (inverter control). Simulation results, conducted using MATLAB Simulink, demonstrate the effectiveness of the proposed hybrid MPPT technique in optimizing the performance of the PV system. The technique exhibits superior tracking efficiency, achieving a convergence time of 0.06 s and an efficiency of 99.86%, and less oscillation than the classical methods. The comparison with other MPPT techniques highlights the advantages of the proposed approach, including higher tracking efficiency and faster response times. The simulation outcomes are analyzed and demonstrate the effectiveness of the proposed control strategies on both sides (the PV array and the grid side). Both PSO and GA offer effective methods for tuning the parameters of a PI current controller. According to considered IEEE standards for low-voltage networks, the total current harmonic distortion values (THD) obtained are considerably high (8.33% and 10.63%, using the PSO and GA algorithms, respectively). Comparative analyses with traditional MPPT methods demonstrate the superior performance of the hybrid approach in terms of tracking efficiency, stability, and rapid response to dynamic changes.
Integration renewable energy sources into current power generation systems necessitates accurate forecasting to optimize and preserve supply-demand restrictions in the electrical grids. Due to the highly random nature of environmental conditions, accurate prediction of PV power has limitations, particularly on long and short periods. Thus, this research provides a new hybrid model for forecasting short PV power based on the fusing of multi-frequency information of different decomposition techniques that will allow a forecaster to provide reliable forecasts. We evaluate and provide insights into the performance of five multi-scale decomposition algorithms combined with a deep convolution neural network (CNN). Additionally, we compare the suggested combination approach's performance to that of existing forecast models. An exhaustive assessment is carried out using three grid-connected PV power plants in Algeria with a total installed capacity of 73.1 MW. The developed fusing strategy displayed an outstanding forecasting performance. The comparative analysis of the proposed combination method with the stand-alone forecast model and other hybridization techniques proves its superiority in terms of forecasting precision, with an RMSE varying in the range of [0.454-1.54] for the three studied PV stations.
In this paper, a critical issue related to power management control in autonomous hybrid systems is presented. Specifically, challenges in optimizing the performance of energy sources and backup systems are proposed, especially under conditions of heavy loads or low renewable energy output. The problem lies in the need for an efficient control mechanism that can enhance power availability while protecting and extending the lifespan of the various power sources in the system. Furthermore, it is necessary to adapt the system's operations to variations in climatic conditions for sustained effectiveness. To address the identified problem. It is proposed the use of an intelligent power management control (IPMC) system employing fuzzy logic control (FLC). The IPMC is designed to optimize the performance of energy sources and backup systems. It aims to predict and adjust the system's operating processes based on variations in climatic conditions, providing a dynamic and adaptive control strategy. The integration of FLC is specifically emphasized for its effectiveness in balancing multiple power sources and ensuring a steady and secure operation of the system. The proposed IPMC with FLC offers several advantages over existing strategies. Firstly, it showcases enhanced power availability, particularly under challenging conditions such as heavy loads or low renewable energy output. Secondly, the system protects and extends the lifespan of the power sources, contributing to long-term sustainability. The dynamic adaptation to climatic variations adds a layer of resilience to the system, making it well-suited for diverse geographical and climatic conditions. The use of realistic data and simulations in MATLAB/Simulink, along with real-time findings from the RT-LAB simulator, indicates the reliability and practical applicability of the proposed IPMC strategy. Efficient load supply and preserved batteries further underscore the benefits of the fuzzy logic-based control strategy in achieving a well-balanced and secure system operation.
In ancient times, Withania coagulans Dunal was used as a therapeutic plant for the treatment of several diseases. This report aims to examine the effect of Agrobacterium tumefactions-mediated transformation of W. coagulans with the rolA gene to enhance secondary metabolite production, antioxidant activity, and anticancer activity of transformed tissues. Before transgenic plant production, the authors designed an efficient methodology for in vitro transformation. In this study, leaf explants were cultured on Murashage and Skoog (MS) media containing different amounts of naphthalene acetic acid (NAA) and benzyl adenine (BA). The best performance for inducing embryogenic callus was in MS medium containing 4 µM NAA and 6.0 µM BA, while the best results for shooting (100%) were obtained at 8 µM benzyl adenine. On the other hand, direct shooting was attained by subculturing leaves on MS medium supplemented with 8 µM benzyl adenine. Prolonged shoots showed excellent in vitro rooting results (80%) with 12 µM indole-3-butyric acid (IBA). The samples were precultivated for 3 days and were followed by 48 h infection with A. tumefaciens strain GV3101 having pCV002. Then, a vector expressed the rol A gene of strain Agrobacterium rhizogenes. Furthermore, three independent transgenic shoot lines and one callus line (T2) were produced and exhibited stable integration of transgene rol A genes, as revealed by PCR analysis. Transgenic strains showed a significant increase in antioxidant potential as compared to untransformed plants. Additionally, LC-MS analysis showed that the transformed strains have a higher withanolide content as compared to untransformed ones. Moreover, the reduced proliferation of prostate cancer cells was observed after treatment with extracts of transgenic plants. Furthermore, these transformed plants exhibited superior antioxidant capability and higher withanolide content than untransformed ones. In conclusion, the reported data can be used to select withanolide-rich germplasm from transformed cell cultures.
This study investigates the application of the Gaussian Radial Basis Function Neural Network (GRNN), Gaussian Process Regression (GPR), and Multilayer Perceptron Optimized by Particle Swarm Optimization (MLP-PSO) models in analyzing the relationship between rainfall and runoff and in predicting runoff discharge. These models utilize autoregressive input vectors based on daily-observed TRMM rainfall and TMR inflow data. The performance evaluation of each model is conducted using statistical measures to compare their effectiveness in capturing the complex relationships between input and output variables. The results consistently demonstrate that the MLP-PSO model outperforms the GRNN and GPR models, achieving the lowest root mean square error (RMSE) across multiple input combinations. Furthermore, the study explores the application of the Empirical Mode Decomposition-Hilbert-Huang Transform (EMD-HHT) in conjunction with the GPR and MLP-PSO models. This combination yields promising results in streamflow prediction, with the MLP-PSO-EMD model exhibiting superior accuracy compared to the GPR-EMD model. The incorporation of different components into the MLP-PSO-EMD model significantly improves its accuracy. Among the presented scenarios, Model M4, which incorporates the simplest components, emerges as the most favorable choice due to its lowest RMSE values. Comparisons with other models reported in the literature further underscore the effectiveness of the MLP-PSO-EMD model in streamflow prediction. This study offers valuable insights into the selection and performance of different models for rainfall-runoff analysis and prediction.
Sea level rise is one of the most serious outcomes of increasing temperatures, leading to coastal flooding, beach erosion, freshwater contamination, loss of coastal habitats, increased soil salinity, and risk of damage to coastal infrastructures. This study estimates the vulnerability to inundation for 2100 in coastal zones in Jeddah Province, Kingdom of Saudi Arabia, under various sea level rise (SLR) scenarios of 1, 2, 5, and 10 m. The predicted flooding was estimated using a combination of factors, including SLR, the bathtub model, digital elevation model, climate scenarios, and land use and land cover. The climate scenarios used were Representative Concentration Pathway (RCP) scenarios 1.9, 2.6, 4.5, and 8.5. The results of the SLR scenarios of 1, 2, 5, and 10 m revealed that 1.6, 4.7, 14.9, and 30.6% (or 88, 214, 679, 1398 km2) of the study area's coast could be classified as inundated areas. The various SLR scenarios can inundate 3.3 to 34% of the road area/length. The inundated built-up and road areas were estimated to range between 0.31 and 0.79 km2, accounting respectively for 1.18 to 3.01% of the total class areas for 1-meter and 2-meter SLR scenarios. In contrast, the inundated area will be significant in the situation of 5 and 10 m SLR scenarios. Regarding the case of a 10-meter SLR scenario, the inundation will negatively impact the built-up and road infrastructure areas, inundating 8.9 km2, with industrial infrastructures affected by inundation estimated at 0.21 km2, followed by green space infrastructures at 0.013 km2. The spatial information based on various SLR scenario impact mapping for Jeddah Province can be highly valuable for decision-makers to better plan future civil engineering structures within the framework of sustainable development.
In this manuscript, a compact in size yet geometrically simple Ultra-Wideband (UWB) antenna is demonstrated. The flexible-by-nature substrate ROGERS 5880, having a thickness of 0.254 mm, is utilized to design the proposed work. The antenna configuration is an excerpt of a traditional rectangular monopole antenna resonating at 5 GHz. Initially, a pair of triangular slots are employed to extend the impedance bandwidth of the antenna. In addition, a semi-circular-shaped, short-ended stub is connected at the upper edges of the patch to further increase the operational bandwidth. After optimization, the proposed antenna offers UWB ranging from 2.73-9.68 GHz, covering almost the entire spectrum allocated globally for UWB applications. Further, the antenna offers a compact size of 15 × 20 mm2 that can easily be integrated into small, flexible electronics. The flexibility analysis is done by bending the antenna on both the x and y axes. The antenna offers performance stability in terms of return loss, radiation pattern, and gain for both conformal and non-conformal conditions. Furthermore, the strong comparison between simulated and measured results for both rigid and bent cases of the antenna, along with the performance comparison with the state-of-the-art, makes it a potential candidate for present and future compact-sized flexible devices.
Electronics , Wireless Technology , Equipment Design , Electric Impedance
This study describes the design and implementation of a small printed ultra-wideband (UWB) antenna for smart electronic systems with on-demand adjustable notching properties. A contiguous sub-band between 3-4.1 GHz, 4.45-6.5 GHz, or for both bands concurrently, can be mitigated by the antenna. Numerous technologies and applications, including WiMAX, Wi-Fi, ISMA, WLAN, and sub-6 GHz, primarily utilize these band segments remitted by the UWB. The upper notch band is implemented by inserting an open-ended stub with the partial ground plane; the lower notch band functionality is obtained by etching a U-shaped slot from the radiating structure. The basic UWB mode is then changed to a UWB mode, with a single or dual notch band, using two diodes to achieve reconfigurability. The antenna has a physically compact size of 17 × 23 mm2 and a quasi-omnidirectional maximum gain of 4.9 dBi, along with a high efficiency of more than 80%, according to both simulation and measurement data. A significant bandwidth in the UWB region is also demonstrated by the proposed design, with a fractional bandwidth of 180% in relation to the 5.2 GHz center frequency. Regarding compactness, consistent gain, and programmable notch features, the proposed antenna outperforms the antennas described in the literature. In addition to these benefits, the antenna's compact size makes it simple to incorporate into small electronic devices and enables producers to build many antennas without complications.
Insulator monitoring using leakage current characteristics is essential for predicting an insulator's health. To evaluate the risk of flashover on the porcelain insulator using leakage current, experimental investigation of leakage current indices was carried out. In the first stage of the experiment, the effect of contamination, insoluble deposit density, wetting rate, and uneven distribution pollution were determined on the porcelain insulator under test. Then, based on the laboratory test results, leakage current information in time and frequency characteristics was extracted and employed as assessment indicators for the insulator's health. Six indicators, namely, peak current indicator, phase shift indicator, slope indicator, crest factor indicator, total harmonic distortion indicator, and odd harmonics indicator, are introduced in this work. The obtained results indicated that the proposed indicators had a significant role in evaluating the insulator's health. To evaluate the insulator's health levels based on the extracted indicator values, this work presents the naïve Bayes technique for the classification and prediction of the insulator's health. Finally, the confusion matrix for the experimental and prediction results for each indicator was established to determine the appropriateness of each indicator in determining the insulator's health status.
Any engineering system involves transitions that reduce the performance of the system and lower its comfort. In the field of automotive engineering, the combination of multiple motors and multiple power sources is a trend that is being used to enhance hybrid electric vehicle (HEV) propulsion and autonomy. However, HEV riding comfort is significantly reduced because of high peaks that occur during the transition from a single power source to a multisource powering mode or from a single motor to a multiple motor traction mode. In this study, a novel model-based soft transition algorithm (STA) is used for the suppression of large transient ripples that occur during HEV drivetrain commutations and power source switches. In contrast to classical abrupt switching, the STA detects transitions, measures their rates, generates corresponding transition periods, and uses adequate transition functions to join the actual and the targeted operating points of a given HEV system variable. As a case study, the STA was applied to minimize the transition ripples that occur in a fuel cell-supercapacitor HEV. The transitions that occurred within the HEV were handled using two proposed transition functions which were: a linear-based transition function and a stair-based transition function. The simulation results show that, in addition to its ability to improve driving comfort by minimizing transient torque ripples and DC bus voltage fluctuations, the STA helps to increase the lifetime of the motor and power sources by reducing the currents drawn during the transitions. It is worth noting that the considered HEV runs on four-wheel drive when the load torque applied on it exceeds a specified torque threshold; otherwise, it operates in rear-wheel drive.
Algorithms , Automobile Driving , Computer Simulation , Electric Power Supplies , Electricity , Motor Vehicles
This paper proposes a novel Fuzzy-MPDTC control applied to a fuel cell battery electric vehicle whose traction is ensured using a permanent magnet synchronous motor (PMSM). On the traction side, model predictive direct torque control (MPDTC) is used to control PMSM torque, and guarantee minimum torque and current ripples while ensuring satisfactory speed tracking. On the sources side, an energy management strategy (EMS) based on fuzzy logic is proposed, it aims to distribute power over energy sources rationally and satisfy the load power demand. To assess these techniques, a driving cycle under different operating modes, namely cruising, acceleration, idling and regenerative braking is proposed. Real-time simulation is developed using the RT LAB platform and the obtained results match those obtained in numerical simulation using MATLAB/Simulink. The results show a good performance of the whole system, where the proposed MPDTC minimized the torque and flux ripples with 54.54% and 77%, respectively, compared to the conventional DTC and reduced the THD of the PMSM current with 53.37%. Furthermore, the proposed EMS based on fuzzy logic shows good performance and keeps the battery SOC within safe limits under the proposed speed profile and international NYCC driving cycle. These aforementioned results confirm the robustness and effectiveness of the proposed control techniques.
This paper highlights a robust optimization and power management algorithm that supervises the energy transfer flow to meet the photovoltaic (PV) electric vehicle demand, even when the traction system is in motion. The power stage of the studied system consists of a triple-junction PV generator as the main energy source, a lithium-ion battery as an auxiliary energy source, and an electric vehicle. The input-output signal adaptation is made by using a stage of energy conversion. A bidirectional DC-DC buck-boost connects the battery to the DC-link. Two unidirectional boost converters interface between the PV generator and the DC link. One is controlled with a maximum power point tracking (MPPT) algorithm to reach the maximum power points. The other is used to control the voltage across the DC-link. The converters are connected to the electric vehicle via a three-phase inverter via the same DC-link. By considering the nonlinear behavior of these elements, dynamic models are developed. A robust nonlinear MPPT algorithm has been developed owing to the nonlinear dynamics of the PV generator, metrological condition variations, and load changes. The high performance of the MPPT algorithm is effectively highlighted over a comparative study with two classical P & O and the fuzzy logic MPPT algorithms. A nonlinear control based on the Lyapunov function has been developed to simultaneously regulate the DC-link voltage and control battery charging and discharging operations. An energy management rule-based strategy is presented to effectively supervise the power flow. The conceived system, energy management, and control algorithms are implemented and verified in the Matlab/Simulink environment. Obtained results are presented and discussed under different operating conditions.
Radio communication systems are very widely present in our current smart lifestyles. It consists of two ends, which can carry the transmitter's information to the receptor. Before installing any radio communication system, it is necessary to analyze the link resources. Hence, this analysis allows the determination of the received radio communication strength to prove if it is sufficient for the link to work correctly and assure a high quality of service. For this reason, new services and technologies are integrated. The objective of the present work is to improve the performance of the radio communication link of 4G systems. The study is based on real measurements using the drive test. The data collected by the drive test are analyzed to increase the performance of the radio communication. Based on this data analysis, recommendations and suggestions are issued for improving the radio communication link. The obtained results indicate a significant amelioration in the performance of the radio communication link.
Communication
The effect of isothermal conditions on the trapping/detrapping process of charges in e-beam irradiated thermally aged XLPE insulation in scanning electron microscopy (SEM) has been investigated. Different isothermal conditions ranging from room temperature to 120 °C are applied on both unaged and aged XLPE samples (2 mm thick) by a suitable arrangement associated with SEM. For each applied test temperature, leakage, and influence currents have been measured simultaneously during and after e-beam irradiation. Experimental results show a big difference between the fresh and aged material regarding trapping and detrapping behavior. It has been pointed out that in the unaged material deep traps govern the process, whereas the shallow traps take part in the aged one. Almost all obtained results reveal that the trapped charge decreases and then increases as the temperature increases for the unaged sample. A deflection temperature corresponding to a minimum is observed at 50 °C. However, for the aged material, the maximum trapped charge decreases continuously with increasing temperature, and the material seems to trap fewer charges under e-beam irradiation at high temperature. Furthermore, thermal aging leads to the occurrence of detrapping process at high temperatures even under e-beam irradiation, which explains the decrease with time evolution of trapped charge during this period. The recorded leakage current increases with increasing temperature for both cases with pronounced values for aged material. The effect of temperature and thermal aging on electrostatic influence factor (K) and total secondary electron emission yield (σ) were also studied.
This paper focuses on robustness and sensitivity analysis for sensor fault diagnosis of a voltage source converter based microgrid model. It uses robust control parameters such as minimum sensitivity parameter (H-), maximum robustness parameter (H∞), and compromised both (H-/H∞), being incorporated in the sliding mode observer theory using the game theoretic saddle point estimation achieved through convex optimization of constrained LMIs. The approach used works in a way that the mentioned robust control parameters are embedded in Hamilton-Jacobi-Isaacs-Equation (HJIE) and are also used to determine the inequality version of HJIE, which is, in terms of the Lyapunov function, faults/disturbances and augmented state/output estimation error as its variables. The stability analysis is also presented by negative definiteness of the same inequality version of HJIE, and additionally, it also gives linear matrix inequalities (LMIs), which are optimized using iterative convex optimization algorithms to give optimal sliding mode observer gains enhanced with robustness to maximal preset values of disturbances and sensitivity to minimal preset values of faults. The enhanced sliding mode observer is used to estimate states, faults, and disturbances using sliding mode observer theory. The optimality of sliding mode observer gains for sensitivity of the observer to minimal faults and robustness to maximal disturbance is a game theoretic saddle point estimation achieved through convex optimization of LMIs. The paper includes results for state estimation errors, faults' estimation/reconstruction, fault estimation errors, and fault-tolerant-control performance for current and potential transformer faults. The considered faults and disturbances in current and potential transformers are sinusoidal nature composite of magnitude/phase/harmonics at the same time.
In-depth understanding of the pollution problems such as dry bands and the polymeric aging process requires better determination of electric field strength and its distribution over the polymeric surface. To determine the electric field distribution over the insulator surface, this research proposes utilizing a novel approach model based on nonlinear electrical characteristics derived from experimental results for polluted polymer insulators. A case study was carried out for a typical 11 kV polymeric insulator to underline the merits of this new modeling approach. The developments of the proposed pollution model and the subsequent computational works are described in detail. The study is divided into two main stages; laboratory measurements and computer simulations. In the first stage, layer conductance tests were carried out to develop nonlinear field-dependent conductivity for the pollution modeling. In the second part, equipotential and electric field distributions along the leakage were computed using the finite element method (FEM). Comparative field studies showed that the simulation using the proposed dynamic pollution model results in more detailed and realistic field profiles around insulators. This may be useful to predict the formation of dry bands and the initiation of electrical discharges on the polymeric surface.
