RESUMEN
This article reviews the recent advances in the field of batteryless near-field communication (NFC) sensors for chemical sensing and biosensing. The commercial availability of low-cost commercial NFC integrated circuits (ICs) and their massive integration in smartphones, used as readers and cloud interfaces, have aroused great interest in new batteryless NFC sensors. The fact that coil antennas are not importantly affected by the body compared with other wireless sensors based on far-field communications makes this technology suitable for future wearable point-of-care testing (PoCT) devices. This review first compares energy harvesting based on NFC to other energy-harvesting technologies. Next, some practical recommendations for designing and tuning NFC-based tags are described. Power transfer is key because in most cases, the energy harvested has to be stable for several seconds and not contaminated by undesired signals. For this reason, the effect of the dimensions of the coils and the conductivity on the wireless power transfer is thoroughly discussed. In the last part of the review, the state of the art in NFC-based chemical and biosensors is presented. NFC-based tags (or sensor tags) are mainly based on commercial or custom NFC ICs, which are used to harvest the energy from the RF field generated by the smartphone to power the electronics. Low-consumption colorimeters and potentiostats can be integrated into these NFC tags, opening the door to the integration of chemical sensors and biosensors, which can be harvested and read from a smartphone. The smartphone is also used to upload the acquired information to the cloud to facilitate the internet of medical things (IoMT) paradigm. Finally, several chipless sensors recently proposed in the literature as a low-cost alternative for chemical applications are discussed.
Asunto(s)
Comunicación , Internet de las Cosas , Conductividad Eléctrica , Electrónica , Pruebas en el Punto de AtenciónRESUMEN
In recent years, there has been a significant increase in the number of collisions between vehicles and vulnerable road users such as pedestrians, cyclists, road workers and more recently scooter riders, especially in urban streets. This work studies the feasibility of enhancing the detection of these users by means of CW radars because they have a low radar cross section. Since the speed of these users is usually low, they can be confused with clutter due to the presence of large objects. To this end, this paper proposes, for the first time, a method based on a spread spectrum radio communication between vulnerable road users and the automotive radar consisting of modulating a backscatter tag, placed on the user. In addition, it is compatible with low-cost radars that use different waveforms such as CW, FSK or FMCW, and hardware modifications are not required. The prototype that has been developed is based on a commercial monolithic microwave integrated circuit (MMIC) amplifier connected between two antennas, which is modulated by switching its bias. Experimental results with a scooter, under static and moving conditions, using a low-power Doppler radar at a 24 GHz band compatible with blind spot radars, are provided.
RESUMEN
This work studies the feasibility of using a battery-less Near-Field Communication (NFC) potentiostat for the next generation of electrochemical point-of-care sensors. A design based on an NFC microchip, a microcontroller, and a custom potentiostat based on an operational amplifier is presented. A proof-of-concept prototype has been designed and used to quantify glucose concentration using commercial glucose test strips from chronoamperometry measurements. The device is harvested and the sensor is read using a mobile phone. The prototype uses an antenna loop covered with ferrite sheets to ensure stable operation of the electronics when the mobile phone is used as reader. The use of ferrite reduces the detuning caused by the proximity of the metal parts of the mobile phone. A comparison with a commercial glucometer device is provided. Results obtained using a commercial glucometer and those provided by the proposed potentiostat show an excellent agreement.
Asunto(s)
Suministros de Energía Eléctrica , Sistemas de Atención de Punto , Compuestos Férricos , GlucosaRESUMEN
The present study exposes an economical and easy-to-use system to assess the heat transfer in building envelopes by determining the U-value. Nowadays these systems require long wires and a host to collect and process the data. In this work, a multi-point system for simultaneous heat flux measurement has been proposed. The aim is to reduce the long measurement time and the cost of thermal isolation evaluations in large buildings. The system proposed consists of a low-cost 3D-printed heat flux sensor integrated with a LoRa transceiver and two temperature sensors. The heat flux (HF) sensor was compared and calibrated with a commercial HF sensor from the Fluxteq brand.
Asunto(s)
Calor , Recolección de DatosRESUMEN
This work studies the feasibility of using backscatter-modulated tags to introduce false information into a signal received by a frequency-modulated continuous-wave (FMCW) radar. A proof-of-concept spoofing device was designed in the 24 GHz ISM band. The spoofing device was based on an amplifier connected between two antennas, and modulation was carried out by switching the amplifier bias. The use of an amplifier allowed us to increase the level of spoofing signal compared with other modulated backscattering methods. The simulated and experimental results show that our method has the ability to generate a pair of false targets at different ranges and velocities depending on the modulation frequency of the chosen tag, since sidebands appear due to this modulation. Countermeasures to detect the spoofing attack based on changes in the slope of the frequency sweep between frames are also proposed.
RESUMEN
The COVID-19 pandemic has highlighted a large amount of challenges to address. To combat the spread of the virus, several safety measures, such as wearing face masks, have been taken. Temperature controls at the entrance of public places to prevent the entry of virus carriers have been shown to be inefficient and inaccurate. This paper presents a smart mask that allows to monitor body temperature and breathing rate. Body temperature is measured by a non-invasive dual-heat-flux system, consisting of four sensors separated from each other with an insulating material. Breathing rate is obtained from the temperature changes within the mask, measured with a thermistor located near the nose. The system communicates by means of long-range (LoRa) backscattering, leading to a reduction in average power consumption. It is designed to establish the relative location of the smart mask from the signal received at two LoRa receivers installed inside and outside an access door. Low-cost LoRa transceivers with WiFi capabilities are used in the prototype to collect information and upload it to a server. Accuracy in body temperature measurements is consistent with measurements made with a thermistor located in the armpit. The system allows checking the correct placement of the mask based on the recorded temperatures and the breathing rate measurements. Besides, episodes of cough can be detected by sudden changes in thermistor temperature.
Asunto(s)
COVID-19 , Máscaras , Atención a la Salud , Calor , Humanos , Pandemias , SARS-CoV-2RESUMEN
This work proposes the use of a modulated tag for direct communication between two vehicles using as a carrier the wave emitted by an FMCW radar installed in the vehicle for advanced driver assistance. The system allows for real-time signals detection and classification, such as stop signal, turn signals and emergency lights, adding redundancy to computer video sensors and without incorporating additional communication systems. A proof-of-concept tag has been designed at the microwave frequency of 24 GHz, consisting of an amplifier connected between receiving and transmitting antennas. The modulation is performed by switching the power supply of the amplifier. The tag is installed on the rear of the car and it answers when it is illuminated by the radar by modulating the backscattered field. The information is encoded in the modulation switching rate used. Simulated and experimental results are given showing the feasibility of the proposed solution.
RESUMEN
This paper presents a color-based classification system for grading the ripeness of fruit using a battery-less Near Field Communication (NFC) tag. The tag consists of a color sensor connected to a low-power microcontroller that is connected to an NFC chip. The tag is powered by the energy harvested from the magnetic field generated by a commercial smartphone used as a reader. The raw RGB color data measured by the colorimeter is converted to HSV (hue, saturation, value) color space. The hue angle and saturation are used as features for classification. Different classification algorithms are compared for classifying the ripeness of different fruits in order to show the robustness of the system. The low cost of NFC chips means that tags with sensing capability can be manufactured economically. In addition, nowadays, most commercial smartphones have NFC capability and thus a specific reader is not necessary. The measurement of different samples obtained on different days is used to train the classification algorithms. The results of training the classifiers have been saved to the cloud. A mobile application has been developed for the prediction based on a table-based method, where the boundary decision is downloaded from a cloud service for each product. High accuracy, between 80 and 93%, is obtained depending on the kind of fruit and the algorithm used.
Asunto(s)
Técnicas Biosensibles , Color , Frutas/química , Tecnología Inalámbrica , Algoritmos , Suministros de Energía Eléctrica , Frutas/crecimiento & desarrollo , Humanos , Dispositivo de Identificación por Radiofrecuencia/métodosRESUMEN
In this article, an overview of recent advances in the field of battery-less near-field communication (NFC) sensors is provided, along with a brief comparison of other short-range radio-frequency identification (RFID) technologies. After reviewing power transfer using NFC, recommendations are made for the practical design of NFC-based tags and NFC readers. A list of commercial NFC integrated circuits with energy-harvesting capabilities is also provided. Finally, a survey of the state of the art in NFC-based sensors is presented, which demonstrates that a wide range of sensors (both chemical and physical) can be used with this technology. Particular interest arose in wearable sensors and cold-chain traceability applications. The availability of low-cost devices and the incorporation of NFC readers into most current mobile phones make NFC technology key to the development of green Internet of Things (IoT) applications.
RESUMEN
A passive harmonic tag for buried assets localization is presented for utility localization. The tag design is based on a dual-polarized patch antenna at Ultra High Frequency (UHF) band. One of its feeders is connected to a frequency doubler based on a Schottky diode that generates the second harmonic, which is transmitted using a linear-polarized patch tuned at this frequency. The power received at the other feeder of the dual-polarized antenna is harvested by an RF to DC converter based on a five-stage voltage multiplier whose energy is used to bias a low-power quartz oscillator that modulates the output of the doubler. The different parts of the system are presented, and the theoretical read range is estimated as a function of the soil composition and the water content. A low-cost reader based on a software defined radio is also presented. Finally, experiments with a prototype of the tag are performed for different soil conditions.
RESUMEN
This paper focuses on the feasibility of tracking the chest wall movement of a human subject during respiration from the waveforms recorded using an impulse-radio (IR) ultra-wideband radar. The paper describes the signal processing to estimate sleep apnea detection and breathing rate. Some techniques to solve several problems in these types of measurements, such as the clutter suppression, body movement and body orientation detection are described. Clutter suppression is achieved using a moving averaging filter to dynamically estimate it. The artifacts caused by body movements are removed using a threshold method before analyzing the breathing signal. The motion is detected using the time delay that maximizes the received signal after a clutter removing algorithm is applied. The periods in which the standard deviations of the time delay exceed a threshold are considered macro-movements and they are neglected. The sleep apnea intervals are detected when the breathing signal is below a threshold. The breathing rate is determined from the robust spectrum estimation based on Lomb periodogram algorithm. On the other hand the breathing signal amplitude depends on the body orientation respect to the antennas, and this could be a problem. In this case, in order to maximize the signal-to-noise ratio, multiple sensors are proposed to ensure that the backscattered signal can be detected by at least one sensor, regardless of the direction the human subject is facing. The feasibility of the system is compared with signals recorded by a microphone.