Combined use of novel chitosan-grafted N-hydroxyethyl acrylamide polyurethane and human dermal fibroblasts as a construct for in vitro-engineered skin.

A rich plethora of information about grafted chitosan (CS) for medical use has been reported. The capability of CS-grafted poly(N-hydroxyethyl acrylamide) (CS-g-PHEAA) to support human dermal fibroblasts (HDFs) in vitro has been proven. However, CS-grafted copolymers lack good stiffness and the characteristic microstructure of a cellular matrix. In addition, whether CS-g-PHEAA can be used to prepare a scaffold with a suitable morphology and mechanical properties for skin tissue engineering (STE) is unclear. This study aimed to show for the first time that step-growth polymerizations can be used to obtain polyurethane (PU) platforms of CS-g-PHEAA, which can also have enhanced microhardness and be suitable for in vitro cell culture. The PU prepolymers were prepared from grafted CS, polyethylene glycol, and 1,6-hexamethylene diisocyanate. The results proved that a poly(saccharide-urethane) [(CS-g-PHEAA)-PU] could be successfully synthesized with a more suitable microarchitecture, thermal properties, and topology than CS-PU for the dynamic culturing of fibroblasts. Cytotoxicity, proliferation, histological and immunophenotype assessments revealed significantly higher biocompatibility and cell proliferation of the derivative concerning the controls. Cells cultured on (CS-g-PHEAA)-PU displayed a quiescent state compared to those cultured on CS-PU, which showed an activated phenotype. These findings may be critical factors in future studies establishing wound dressing models.

Discovering the effect of solvents on poly(2-aminoethyl methacrylate) grafting onto chitosan for an in vitro skin model.

The design of controlled grafting copolymers is critical in synthesizing effective artificial cellular matrices because of their regulatory role in cellular behavior. However, it is unclear whether poly(2-aminoethyl methacrylate) grafted onto chitosan generated by gamma-radiation-induced graft polymerization in different solvents can influence the physicochemical properties and biotech applicability of the copolymer. This work aims to demonstrate for the first time the effect of various solvents on the synthesis, properties, and biological performance of grafted chitosan using the simultaneous irradiation method. The results proved that the solvent is one of the critical factors affecting the properties of the modified polysaccharide. The degree of grafting showed a solvent-dependent profile. Hexane presented utmost importance concerning the degree of grafting. Ethyl acetate showed the best results in grafting extent and human dermal fibroblast growth. These findings indicate that proper solvent selection determines the possible copolymer use for in vitro engineered skin substitute models.

A poly (saccharide-ester-urethane) scaffold for mammalian cell growth.

Chitosan and poly(3-hydroxybutyrate) are non-toxic, biodegradable, and biocompatible polymers extensively used in regenerative medicine. However, it is unknown whether the chemical combination of these polymers can produce a biomaterial that induces an appropriate cellular response in vitro in mammalian cells. This study aimed to test the ability of a novel salt-leached polyurethane scaffold of chitosan grafted with poly(3-hydroxybutyrate) to support the growth of three mammalian cell lines of different origin: a) HEK-293 cells, b) i28 mouse myoblasts, and c) human dermal fibroblasts. The viability of the cells was assessed by either evaluation of their capacity to maintain the expression of the green fluorescent protein by adenoviral transduction or by esterase activity and plasma membrane integrity. The results indicated that the three cell lines attached well to the scaffold; however, when i28 cells were induced to differentiate, they did not produce morphologically distinct myofibers, and cell growth ceased. In conclusion, the findings reveal that, altogether, these observations suggest that this foam scaffold supports cell growth and proliferation but may not apply to all cell types. Hence, one crucial question yet to be resolved is a poly (saccharide-ester-urethane) derivative with a nano-topography that elicits a similar cellular response for different biological environments.