Polyimide is actively applied in various industrial fields because of its strong mechanical properties, owing to the interactions between the polymer chains. Fully aromatic imide structures exhibit high glass-transition temperatures due to the strong interactions between their chains, which hinder chain mobility. Therefore, preparing a material that exhibits self-healing at a low temperature of ≤100 °C and good mechanical properties is challenging. Thus, we prepared imides with four-component semiaromatic structures by adjusting the contents of 4,4'-(hexafluoroisopropylidene)diphthalic anhydride and 4,4'-(4,4'-isopropylidenediphenoxy)bis(phthalic anhydride) to yield four-component self-healable colorless polyimides (f-SH-CPIs) with novel structures, flexibilities, good mechanical properties, and low healing temperatures. The flexibilities and distances between the polymer chains, as the basis of the trade-off relationship between the mechanical properties and healing efficiency, were controlled. These materials may be used as substrates in wearable devices and multilayer insulation that may protect from space dust, cosmic rays, and satellite fragments.
Polymeric coating materials (PCMs) are promising candidates for developing next-generation flexible displays. However, PCMs are frequently subjected to external stimuli, making them highly susceptible to repeated damage. Therefore, in this study, a highly self-healing PCM based on a charge transfer complex (CTC) was developed, and its thermal, self-healing, and mechanical properties were examined. The self-healing material demonstrated improved thermal stability, fast self-healing kinetics (1 min), and a high self-healing efficiency (98.1%) via CTC-induced multiple interactions between the polymeric chains. In addition, it eliminated the trade-off between the mechanical strength and self-healing capability that is experienced by typical self-healing materials. The developed PCM achieved excellent self-healing and superior bulk (in-plane) and surface (out-of-plane) mechanical strengths compared to those of conventional engineering plastics such as polyether ether ketone (PEEK), polysulfone (PSU), and polyethersulfone (PES). These remarkable properties are attributed to the unique intermolecular structure resulting from strong CTC interactions. A mechanism for the improved self-healing and mechanical properties was also proposed by comparing the CTC-based self-healing PCMs with a non-CTC-based PCM.
The formic acid (CH2O2) decomposition over sulfated zirconia (SZ) catalysts prepared under different synthesis conditions, such as calcination temperature (500-650 °C) and sulfate loading (0-20 wt.%), was investigated. Three sulfate species (tridentate, bridging bidentate, and pyrosulfate) on the SZ catalysts were characterized by using temperature-programmed decomposition (TPDE), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The acidic properties of the SZ catalysts were investigated by the temperature-programmed desorption of iso-propanol (IPA-TPD) and pyridine-adsorbed infrared (Py-IR) spectroscopy and correlated with their catalytic properties in formic acid decomposition. The relative contributions of Brønsted and Lewis acid sites to the formic acid dehydration were compared, and optimal synthetic conditions, such as calcination temperature and sulfate loading, were proposed.
Polyimides, a widely used engineering plastic, require use of large amounts of toxic and hazardous organic solvents which threaten our daily lives, calling for new and easy synthetic methods for sustainable environmentally friendly development. In this paper, highly soluble fluorinated polyimides based on 4,4'-(hexafluoroisopropylidene) diphthalic anhydride were synthesized via hydrothermal process without using any toxic organic solvents and the advantages of the newly demonstrated synthetic methods are shown by comparative analysis performed with the two conventional synthetic methods using organic solvent: thermal and chemical imidization. Lower temperature is required (~200 °C) compared to thermal imidization and functional groups for high fusibility formed more easily compared to chemical imidization. According to the comparative analysis, hydrothermally synthesized PIs showed excellent solubility and maintained high thermal stability (>500 °C) and glass transition temperature (>300 °C) compared to conventional PI. The hydrothermally synthesized polyimide is much more convenient to store and manage than other form of polyimide which is much more stable when it is exposed to humidity as it is a powder form. The hydrothermal synthetic method is verified to be a "Green" and facile method for sustainable PI synthesis.
An inexpensive and general-purpose carbon fiber was prepared using coal tar pitch. In contrast to the solvent extraction process employing expensive solvents, a low-cost centrifugal separation method facilitated the reduction of loss due to the pitch purification and an overall yield increase. The coal tar pitch purified by centrifugation and subsequently co-carbonized with pyrolysis fuel oil improved in spinnability. Moreover, the resulting spinnable pitch had a softening point of 250 °C. The obtained carbon fibers were heat-treated at 1000 °C for 5 min, resulting in a tensile strength of approximately 1000 MPa and an average diameter of 9 µm. In this study, we present an effective method for obtaining low-cost general-purpose isotropic carbon fibers.
To cope with the demand for cleaner alternative energy, polymer electrolyte membrane fuel cells (PEMFCs) have received significant research attention owing to their high-power density, high fuel efficiency, and low polluting by-product. However, the water requirement of these cells has necessitated research on systems that do not require water and/or use other mediums with higher boiling points. In this work, a highly porous meta-polybenzimidazole (m-PBI) membrane was fabricated through the non-solvent induced phase inversion technique and thermal cross-linking for high-temperature PEMFC (HT-PEMFC) applications. Standard non-thermally treated porous membranes are susceptible to phosphoric acid (PA) even at low concentrations and are unsuitable as polymer electrolyte membranes (PEMs). With the porous structure of m-PBI membranes, higher PA uptake and minimal swelling, which is controlled via cross-linking, was achieved. In addition, the membranes exhibited partial asymmetrical morphology and are directly applicable to fuel cell systems without any further modifications. Membranes with insufficient cross-linking resulted in an unstable performance in HT-PEMFC environments. By optimizing thermal treatment, a high-performance membrane with limited swelling and improved proton conductivity was achieved. Finally, the m-PBI membrane exhibited enhanced acid retention, proton conductivity, and fuel cell performance.
Polymer composite membrane technology is promising for enhancing the performance of membrane electrode assemblies for high-temperature fuel cells. In this study, we developed a novel anhydrous proton-exchange polybenzimidazole (m-PBI) composite membrane using Al-substituted mesoporous silica (Al-MCM-41) as a proton-carrier support. The surface-substituted Al-MCM-41 formed effective proton-transport pathways via its periodic hexagonal channel and improved the proton conductivity. The proton conductivity of an m-PBI filled with 9 wt.% filler was 0.356 S cm-1 at 160 °C and 0% humidity, representing an increase of 342% compared to that of a pristine m-PBI. Further, the current density at 0.6 V and maximum power density of m-PBI composite membranes were increased to 0.393 A cm-2 and 0.516 W cm-2, respectively. The enhanced fuel-cell performance was attributed to the proton-transfer channels and H3PO4 reservoirs formed by the mesopores of the Al-MCM-41 shell. The results indicated that Al-MCM-41 is suitable with respect to the hybrid homologues for enhancing the proton transport of the m-PBI membrane.
Nanocomposite polymer electrolyte membranes comprising a crosslinked polymer blend of poly(vinyl alcohol)/poly(styrene sulfonic acid-co-maleic acid) (PVA/PSSA-co-MA) and fumed silica nanoparticles were prepared for direct methanol fuel cell (DMFC) applications. Silica nanoparticles could be incorporated well uniformly in the completely miscible system, which can form a three-dimensional network structure to achieve the enhancement of mechanical properties as well as the additional reduction of methanol permeability. The optimized proton conductivities and methanol permeability of the PVA/PSSA-co-MA membrane with silica nanoparticles of 10 wt.% were 0.0482 S cm-1 at room temperature and 5.78 × 10-7 cm2 s-1 at the methanol concentration of 40% (w/w), respectively.
The current paper describes enhanced electrochemical capacitive performance of chemically grown Cobalt hydroxide (Co(OH)2) nanorods (NRs) decorated porous three dimensional graphitic carbon foam (Co(OH)2/3D GCF) as a supercapacitor electrode. Freestanding 3D porous GCF is prepared by carbonizing, high internal phase emulsion (HIPE) polymerized styrene and divinylbenzene. The PolyHIPE was sulfonated and carbonized at temperature up to 850 °C to obtain graphitic 3D carbon foam with high surface area (389 m2 g-1) having open voids (14 µm) interconnected by windows (4 µm) in monolithic form. Moreover, entangled Co(OH)2 NRs are anchored on 3D GCF electrodes by using a facile chemical bath deposition (CBD) method. The wide porous structure with high specific surface area (520 m2 g-1) access offered by the interconnected 3D GCF along with Co(OH)2 NRs morphology, displays ultrahigh specific capacitance, specific energy and power. The Co(OH)2/3D GCF electrode exhibits maximum specific capacitance about ~1235 F g-1 at ~1 A g-1 charge-discharge current density, in 1 M aqueous KOH solution. These results endorse potential applicability of Co(OH)2/3D GCF electrode in supercapacitors and signifies that, the porous GCF is a proficient 3D freestanding framework for loading pseudocapacitive nanostructured materials.
In this contribution, chemical sensor for the detection of aqueous ammonia has been fabricated using UV-curable polyurethane acrylate (PU) and nanohybrids (NH-1, NH-3 and NH-5). PU has been prepared by reacting polycaprolactone triol (PCLT) and isophorone diisocyanate (IPDI) while the nanohybrids, NH-1, NH-3, and NH-5 have been synthesized by solution blending method using PU with 1, 3, and 5 wt% loading levels of C-20B. PU and their nanohybrids showed higher sensitivity investigated by I-V technique using aqueous ammonia as a target chemical. All the nanohybrids showed higher sensitivity as compared to neat PU. The sensitivity increased with increase in clay content and the nanohybrid containing 5 wt% of clay showed the highest sensitivity (8.5254 µA cm(-2) mM(-1)) with the limit of detection (LOD) of 0.0175 ± 0.001 µM, being 7.8 times higher than pure PU. The calibration plot for all the sensors was linear over the large range of 0.05 µM to 0.05 M. The response time of the fabricated sensor was <10.0 s. Therefore, one can fabricate efficient aqueous ammonia sensor by utilization of nanohybrid as an efficient electron mediator.
Aluminum Silicates/chemistry , Ammonia/analysis , Chemistry Techniques, Analytical/instrumentation , Nanocomposites/chemistry , Polyurethanes/chemistry , Ultraviolet Rays , Water/chemistry , Clay , Environmental Pollutants/analysis , Photochemical Processes
A series of benzoic acid derivatives 1-10 have been synthesised by two different methods. Compounds 1-6 were synthesised by a facile procedure for esterification using N,N'-dicyclohexylcarbodiimide (DCC) as a coupling agent, methylene chloride as a solvent system and dimethylaminopyridine (DMAP). While 7-10 were synthesised by converting benzoic acid into benzoyl chloride by treating with thionyl chloride in the presence of benzene and performing a further reaction with amine in dried benzene. The structures of all the synthesised derivatives of benzoic acid (1-10) were assigned on the basis of extensive NMR studies. All of them showed inhibitory potential against tyrosinase. Among them, compound 7 was found to be the most potent (1.09 µM) when compared with the standard tyrosinase inhibitors of kojic acid (16.67 µM) and L-mimosine (3.68 µM). Finally in this paper, we have discussed the structure-activity relationships of the synthesised molecules.
Benzoates/chemistry , Benzoates/pharmacology , Drug Design , Enzyme Inhibitors/chemistry , Enzyme Inhibitors/pharmacology , Monophenol Monooxygenase/antagonists & inhibitors , 4-Aminopyridine/analogs & derivatives , 4-Aminopyridine/chemistry , Benzamides/chemical synthesis , Benzamides/chemistry , Benzamides/pharmacology , Benzoates/chemical synthesis , Dicyclohexylcarbodiimide/chemistry , Enzyme Inhibitors/chemical synthesis , Kinetics , Molecular Structure , Structure-Activity Relationship
