Efficient rare earth element (REE) separations are becoming increasingly important to technologies ranging from renewable energy and high-performance magnets to applied radioisotope separations. These separations are made challenging by the extremely similar chemical and physical characteristics of the individual elements, which almost always occupy the 3+ oxidation state under ambient conditions. Herein, we discuss the development of a novel REE separation aimed at obtaining purified samples of neodymium (Nd) on a multi-milligram scale using high-speed counter-current chromatography (HSCCC). The method takes advantage of the subtle differences in ionic radii between neighboring REEs to tune elution rates in dilute acid through implementation of the di-(2-ethylhexyl)phosphoric acid (HDEHP)-infused stationary phase (SP) of the column. A La/Ce/Nd/Sm separation was demonstrated at a significantly higher metal loading than previously accomplished by HSCCC (15 mg, RNd/REE > 0.85), while the Pr/Nd separation was achieved at lower metal loadings (0.3 mg, RNd/Pr = 0.75 - 0.83). The challenges associated with scaling REE separations via HSCCC are presented and discussed within.
Countercurrent Distribution , Neodymium , Countercurrent Distribution/methods , Neodymium/chemistry , Neodymium/isolation & purification , Organophosphates
Quantifying 64Cu in post-detonation nuclear debris samples can provide important diagnostic information regarding the structural materials used within a nuclear device. However, this task is challenging due to the weak gamma emissions associated with the decay of 64Cu, its short half-life (12.701 h), and the presence of interfering fission product radioisotopes. Large quantities of debris sample are generally needed to accurately quantify 64Cu, which can be problematic in sample-limited scenarios where other radiometric analyses are required. Herein, we present a new method for the separation of 64Cu from solutions of mixed fission products and demonstrate the quantification of its activity through use of gas-flow proportional beta counting. The new method was validated through a series of rigorous tests and was shown to improve the detection limit of 64Cu by over two orders of magnitude, from 2.5 × 106 to 1.3 × 104 atoms/sample for 100 min measurements.
Comparison of bonding and electronic structural features between trivalent lanthanide (Ln) and actinide (An) complexes across homologous series' of molecules can provide insights into subtle and overt periodic trends. Of keen interest and debate is the extent to which the valence f- and d-orbitals of trivalent Ln/An ions engage in covalent interactions with different ligand donor functionalities and, crucially, how bonding differences change as both the Ln and An series are traversed. Synthesis and characterization (SC-XRD, NMR, UV-vis-NIR, and computational modeling) of the homologous lanthanide and actinide N-heterocyclic carbene (NHC) complexes [M(C5Me5)2(X)(IMe4)] {X = I, M = La, Ce, Pr, Nd, U, Np, Pu; X = Cl, M = Nd; X = I/Cl, M = Nd, Am; and IMe4 = [C(NMeCMe)2]} reveals consistently shorter An-C vs Ln-C distances that do not substantially converge upon reaching Am3+/Nd3+ comparison. Specifically, the difference of 0.064(6) Å observed in the La/U pair is comparable to the 0.062(4) Å difference observed in the Nd/Am pair. Computational analyses suggest that the cause of this unusual observation is rooted in the presence of π-bonding with the valence d-orbital manifold in actinide complexes that is not present in the lanthanide congeners. This is in contrast to other documented cases of shorter An-ligand vs Ln-ligand distances, which are often attributed to increased 5f vs 4f radial diffusivity leading to differences in 4f and 5f orbital bonding involvement. Moreover, in these traditional observations, as the 5f series is traversed, the 5f manifold contracts such that by americium structural studies often find no statistically significant Am3+vs Nd3+ metal-ligand bond length differences.
In nuclear forensic analyses, measurements of actinide elements in a sample can assist with identifying interdicted or unknown materials. While these radiochemical signatures have been extensively investigated in uranium materials, less is known about bulk neptunium samples. This paper describes the measurement of trace actinide concentrations and isotopic profiles in a 237Np oxide sample. Uranium, plutonium, americium, and curium concentrations and isotopic profiles in the sample were determined and deemed potentially useful for distinguishing different sources of 237Np. Several different potential radiochronometry systems were also investigated; discordant results indicate that the Np sample was never completely purified of other actinide elements, or that subsequent contamination of the sample occurred. Few prior studies of neptunium materials have been reported, and these data suggest that trace actinide constituents could provide unique signatures to identify material out of regulatory control.
A method has been developed to purify and measure platinum radioisotopes in the presence of fission products and environmental constituents. The method uses a combination of cation exchange and anion exchange chromatography and selective precipitation steps to remove other radioisotopes from the sample. The addition of stable platinum carrier allows for a gravimetric determination of the chemical yield of the procedure. Overall, the method is fast, simple, and potentially applicable for rapid turnaround of unknown samples. Using this method, multiple platinum radioisotopes were measured in two different irradiation experiments. The measured ratios of the platinum radioisotopes clearly reflect the neutron spectrum of the irradiation, suggesting that platinum radioisotopes could be valuable signatures in nuclear forensic analyses.
Including sea-level rise (SLR) projections in planning and implementing coastal adaptation is crucial. Here we analyze the first global survey on the use of SLR projections for 2050 and 2100. Two-hundred and fifty-three coastal practitioners engaged in adaptation/planning from 49 countries provided complete answers to the survey which was distributed in nine languages - Arabic, Chinese, English, French, Hebrew, Japanese, Korean, Portuguese and Spanish. While recognition of the threat of SLR is almost universal, only 72% of respondents currently utilize SLR projections. Generally, developing countries have lower levels of utilization. There is no global standard in the use of SLR projections: for locations using a standard data structure, 53% are planning using a single projection, while the remainder are using multiple projections, with 13% considering a low-probability high-end scenario. Countries with histories of adaptation and consistent national support show greater assimilation of SLR projections into adaptation decisions. This research provides new insights about current planning practices and can inform important ongoing efforts on the application of the science that is essential to the promotion of effective adaptation.
Background: While multiple clinical trials have demonstrated benefits of early palliative care for people with cancer, access to these services is frequently very late if at all. Establishing evidence-based, disease-specific 'triggers' or times for the routine integration of early palliative care may address this evidence-practice gap. Aim: To test the feasibility of using defined triggers for the integration of standardised, early palliative (STEP) care across three advanced cancers. Method: Phase II, multi-site, open-label, parallel-arm, randomised trial of usual best practice cancer care +/- STEP Care conducted in four metropolitan tertiary cancer services in Melbourne, Australia in patients with advanced breast, prostate and brain cancer. The primary outcome was the feasibility of using triggers for times of integration of STEP Care, defined as enrolment of at least 30 patients per cancer in 24 months. Triggers were based on hospital admission with metastatic disease (for breast and prostate cancer), or development of disease recurrence (for brain tumour cohort). A mixed method study design was employed to understand issues of feasibility and acceptability underpinning trigger points. Results: The triggers underpinning times for the integration of STEP care were shown to be feasible for brain but not breast or prostate cancers, with enrolment of 49, 6 and 10 patients across the three disease groups respectively. The varied feasibility across these cancer groups suggested some important characteristics of triggers which may aid their utility in future work. Conclusions: Achieving the implementation of early palliative care as a standardized component of quality care for all oncology patients will require further attention to defining triggers. Triggers which are 1) linked to objective points within the illness course (not dependent on recognition by individual clinicians), 2) Identifiable and visible (heralded through established service-level activities) and 3) Not reliant upon additional screening measures may enhance their feasibility.
Measurements of the ruthenium isotopic composition of nuclear samples could provide information about the method of sample production, sample irradiation history, and age. To investigate the feasibility and applicability of this idea, this study focuses on measurements of the ruthenium isotope composition of a nominally single-isotope 106Ru radioactivity standard, where the complications of environmental mixing are eliminated. The measurements of the 106Ru standards reveal unusual stable ruthenium isotopic compositions consistent with fissiogenic ruthenium. Three different lots of the material have been investigated, and the isotopic composition is found to be different for lot 1 as compared to lots 2 and 3, indicating a longer irradiation duration incurred during the production of lot 1. Through measurements of 106Ru and its 106Pd daughter, radiochronometry can be used to infer the ages of the samples. Lot 1 is older than lots 2 and 3 and was produced 4.91(5) years before the reference date of 1/1/21, approximately 2.7 years before lots 2 and 3. In an effort to better understand the sample production pathway, the isotopic measurements are compared with nuclear reactor simulations, which suggest that the material was generated by irradiation of a low-enriched uranium target material in a light water reactor. These findings have significant implications for nuclear treaty monitoring, providing an example of the power of ruthenium isotope measurements to discern details of sample origin and history.
Ruthenium , Uranium , Isotopes , Reference Standards , Uranium/analysis
G protein coupled receptors signal through G proteins or arrestins. A long-standing mystery in the field is why vertebrates have two non-visual arrestins, arrestin-2 and arrestin-3. These isoforms are ~75% identical and 85% similar; each binds numerous receptors, and appear to have many redundant functions, as demonstrated by studies of knockout mice. We previously showed that arrestin-3 can be activated by inositol-hexakisphosphate (IP6). IP6 interacts with the receptor-binding surface of arrestin-3, induces arrestin-3 oligomerization, and this oligomer stabilizes the active conformation of arrestin-3. Here, we compared the impact of IP6 on oligomerization and conformational equilibrium of the highly homologous arrestin-2 and arrestin-3 and found that these two isoforms are regulated differently. In the presence of IP6, arrestin-2 forms "infinite" chains, where each promoter remains in the basal conformation. In contrast, full length and truncated arrestin-3 form trimers and higher-order oligomers in the presence of IP6; we showed previously that trimeric state induces arrestin-3 activation (Chen et al., 2017). Thus, in response to IP6, the two non-visual arrestins oligomerize in different ways in distinct conformations. We identified an insertion of eight residues that is conserved across arrestin-2 homologs, but absent in arrestin-3 that likely accounts for the differences in the IP6 effect. Because IP6 is ubiquitously present in cells, this suggests physiological consequences, including differences in arrestin-2/3 trafficking and JNK3 activation. The functional differences between two non-visual arrestins are in part determined by distinct modes of their oligomerization. The mode of oligomerization might regulate the function of other signaling proteins.
Amino Acids/chemistry , Arrestins/chemistry , Models, Molecular , Protein Conformation , Protein Multimerization , Arrestins/metabolism , Binding Sites , Humans , Phytic Acid/chemistry , Protein Binding , Protein Isoforms , Solutions , Spectrum Analysis
BACKGROUND: Current international consensus is that 'early' referral to palliative care services improves cancer patient and family carer outcomes; however, in practice, these referrals are not routine. Uncertainty about the 'best time' to refer has been highlighted as contributing to care variation. Previous work has identified clear disease-specific transition points in the cancer illness which heralded subsequent poor prognosis (less than 6 months) and which, we contest, represent times when palliative care should be routinely introduced as a standardised approach, if not already in place, to maximise patient and carer benefit. This protocol details a trial that will test the feasibility of a novel standardised outpatient model of early palliative care [Standardised Early Palliative Care (STEP Care)] for advanced cancer patients and their family carers, with referrals occurring at the defined disease-specific evidence-based transition points.The aims of this study are to (1) determine the feasibility of conducting a definitive phase 3 randomised trial, which evaluates effectiveness of STEP Care (compared to usual best practice cancer care) for patients with advanced breast or prostate cancer or high grade glioma; (2) examine preliminary efficacy of STEP Care on patient/family caregiver outcomes, including quality of life, mood, symptoms, illness understanding and overall survival; (3) document the impact of STEP Care on quality of end-of-life care; and (4) evaluate the timing of palliative care introduction according to patients, families and health care professionals. METHODS: Phase 2, multicenter, open-label, parallel-arm, randomised controlled trial (RCT) of STEP Care plus standard best practice cancer care versus standard best practice cancer care alone. DISCUSSION: The research will test the feasibility of standardised palliative care introduction based on illness transitions and provide guidance on subsequent development of phase 3 studies of integration. This will directly address the current uncertainty about palliative care timing. TRIAL REGISTRATION: Australian New Zealand Clinical Trials Registry ACTRN12617000534381.
This paper describes an approach to measuring extinct fission products that would allow for the characterization of a nuclear test at any time. The isotopic composition of molybdenum in five samples of glassy debris from the 1945 Trinity nuclear test has been measured. Nonnatural molybdenum isotopic compositions were observed, reflecting an input from the decay of the short-lived fission products (95)Zr and (97)Zr. By measuring both the perturbation of the (95)Mo/(96)Mo and (97)Mo/(96)Mo isotopic ratios and the total amount of molybdenum in the Trinity nuclear debris samples, it is possible to calculate the original concentrations of the (95)Zr and (97)Zr isotopes formed in the nuclear detonation. Together with a determination of the amount of plutonium in the debris, these measurements of extinct fission products allow for new estimates of the efficiency and yield of the historic Trinity test.
The synthesis and characterization of air stable Fe(II) coordination complexes with tetrazine and triazolo-tetrazine ligands and perchlorate counteranions have been achieved. Time-dependent density functional theory (TD-DFT) was used to model the structural, electrochemical, and optical properties of these materials. These compounds are secondary explosives that can be initiated with Nd:YAG laser light at lower energy thresholds than those of PETN. Furthermore, these Fe(II) tetrazine complexes have significantly lower sensitivity than PETN toward mechanical stimuli such as impact and friction. The lower threshold for laser initiation was achieved by altering the electronic properties of the ligand scaffold to tune the metal ligand charge transfer (MLCT) bands of these materials from the visible into the near-infrared region of the electromagnetic spectrum. Unprecedented decrease in both the laser initiation threshold and the mechanical sensitivity makes these materials the first explosives that are both safer to handle and easier to initiate than PETN with NIR lasers.
Complexes of 3-amino-6-(3,5-dimethylpyrazole)tetrazine) (NH2TzDMP, 1) and 3-(3,3'-dinitroazetidine)-6-(3,5-dimethylpyrazole)tetrazine) (DNAZTzDMP, 2) with first row transition metal centers were synthesized. Reactions of Fe(II)(H2O)6(BF4)2 and Fe(NO3)3·9H2O with 1 and 2 both led to complexes of the form [(RTzDMP)3Fe]X2 (X = BF4, R = NH2 (3), DNAZ (4); X = NO3, R = NH2 (5), DNAZ (6)), which showed intense MLCT bands in the visible region of the spectrum. Ligands 1 and 2 also reacted with Cu(II)(NO3)2·5/2H2O to form [(RTzDMP)2Cu(NO3)][NO3] (R = NH2 (7), DNAZ (8)) in addition to reacting with Cu(I)(CH3CN)4(PF6) to form [(RTzDMP)2Cu][PF6] (R = NH2 (9), DNAZ (10)). Lastly reactions of 1 and 2 with Co(NO3)2·6H2O and Ni(NO3)2·6H2O led to [(NH2TzDMP)2Co(H2O) (NO3)][NO3] (11), [(DNAZTzDMP)2Co(H2O)2][NO3]2 (12), [(NH2TzDMP)3Ni][NO3]2 (13), and [(DNAZTzDMP)2Ni(H2O)2][NO3]2 (14). The complexes display rich electrochemical and photophysical properties that are unaffected by derivation with explosive groups.
Explosive Agents/chemistry , Optical Phenomena , Organometallic Compounds/chemistry , Organometallic Compounds/chemical synthesis , Pyrazoles/chemistry , Transition Elements/chemistry , Crystallography, X-Ray , Drug Stability , Electrochemistry , Explosive Agents/chemical synthesis , Ligands , Mechanical Phenomena , Models, Molecular , Molecular Conformation , Temperature
This work began as part of a biomass conversion catalysis project with UC Santa Barbara funded by the first NSF Chemical Bonding Center, CATSB. Recognizing that catalytic aerobic oxidation of diol C-C bonds could potentially be used to break down lignocellulose, we began to synthesize oxovanadium complexes and explore their fundamental reactivity. Of course there were theories regarding the oxidation mechanism, but our mechanistic studies soon revealed a number of surprises of the type that keep all chemists coming back to the bench! We realized that these reactions were also exciting in that they actually used the oxygen-on-every-carbon property of biomass-derived molecules to control the selectivity of the oxidation. When we found that these oxovanadium complexes tended to convert sugars predominantly to formic acid and carbon dioxide, we replaced one of the OH groups with an ether and entered the dark world of lignin chemistry. In this Account, we summarize results from our collaboration and from our individual labs. In particular, we show that oxidation selectivity (C-C vs C-O bond cleavage) of lignin models using air and vanadium complexes depends on the ancillary ligands, the reaction solvent, and the substrate structure (i.e., phenolic vs non-phenolic). Selected vanadium complexes in the presence of added base serve as effective alcohol oxidation catalysts via a novel base-assisted dehydrogenation pathway. In contrast, copper catalysts effect direct C-C bond cleavage of these lignin models, presumably through a radical pathway. The most active vanadium catalyst exhibits unique activity for the depolymerization of organosolv lignin. After Weckhuysen's excellent 2010 review on lignin valorization, the number of catalysis studies and approaches on both lignin models and extracts has expanded rapidly. Today we are seeing new start-ups and lignin production facilities sprouting up across the globe as we all work to prove wrong the old pulp and paper chemist's adage: you can make anything from lignin except money!
Lignin/chemistry , Organometallic Compounds/chemistry , Catalysis , Models, Molecular , Molecular Structure , Oxidation-Reduction
An optimized method was developed to analyze environmental soil and sediment samples for (237)Np, (239)Pu, and (240)Pu by ICP-MS using a (242)Pu isotope dilution standard. The high yield, short time frame required for analysis, and the commercial availability of the (242)Pu tracer are significant advantages of the method. Control experiments designed to assess method uncertainty, including variation in inter-element fractionation that occurs during the purification protocol, suggest that the overall precision for measurements of (237)Np is typically on the order of ± 5%. Measurements of the (237)Np concentration in a Peruvian Soil blank (NIST SRM 4355) spiked with a known concentration of (237)Np tracer confirmed the accuracy of the method, agreeing well with the expected value. The method has been used to determine neptunium and plutonium concentrations in several environmental matrix standard reference materials available from NIST: SRM 4357 (Radioactivity Standard), SRM 1646a (Estuarine Sediment) and SRM 2702 (Inorganics in Marine Sediment).
Geologic Sediments/analysis , Neptunium/analysis , Plutonium/analysis , Radiation Monitoring/methods , Soil Pollutants, Radioactive/analysis , Water Pollutants, Radioactive/analysis , Chemical Fractionation , England , Mass Spectrometry , United States
As part of a nuclear forensics capability, rapid and effective methods to analyze for plutonium and other actinide metals are needed. A key requirement of these methods is that they afford a high chemical yield while still providing isotopic information necessary for forensic evaluation. Toward this objective, a new method for binding plutonium for analysis by alpha spectrometry has been developed. Thin films of Kläui-type tripodal oxygen donor ligands were prepared by spin-casting solutions onto glass substrates. Three different ligands were evaluated for plutonium binding, and the best results were obtained using the ethyl-substituted complex Na[Cp*Co(P(O)(OEt)2)3], which bound 80-88% of the dissolved Pu under equilibrium conditions. The thin films are simple and inexpensive to prepare and exhibit excellent alpha spectral resolution, having line widths of ~33 keV. The method has been successfully applied to analyze for plutonium in both an archived nuclear debris sample and a certified environmental soil sample. The results obtained from the soil analysis are in good agreement with the certified values, demonstrating the effectiveness of the method for rapid plutonium analysis.
Mammals express four arrestin subtypes, three of which have been shown to self-associate. Cone photoreceptor-specific arrestin-4 is the only one that is a constitutive monomer. Visual arrestin-1 forms tetramers both in crystal and in solution, but the shape of its physiologically relevant solution tetramer is very different from that in the crystal. The biological role of the self-association of arrestin-1, expressed at very high levels in rod and cone photoreceptors, appears to be protective, reducing the concentration of cytotoxic monomers. The two nonvisual arrestin subtypes are highly homologous, and self-association of both is facilitated by IP6, yet they form dramatically different oligomers. Arrestin-2 apparently self-associates into "infinite" chains, very similar to those observed in IP6-soaked crystals, where IP6 connects the concave sides of the N- and C-domains of adjacent protomers. In contrast, arrestin-3 only forms dimers, in which IP6 likely connects the C-domains of two arrestin-3 molecules. Thus, each of the three self-associating arrestins does it in its own way, forming three different types of oligomers. The physiological role of the oligomerization of arrestin-1 and both nonvisual arrestins might be quite different, and in each case it remains to be definitively elucidated.
Arrestins/metabolism , Retinal Cone Photoreceptor Cells/metabolism , Retinal Rod Photoreceptor Cells/metabolism , Animals , Crystallization , Humans , Phytic Acid/metabolism , Protein Multimerization
