RESUMEN
Metal-organic framework (MOF) derivatives with tunable pore structure and improved conductivity are intensively designed as electroactive materials. Incorporating structure directing agents (SDA) is beneficial for designing MOF derivatives with excellent electrochemical performances. Ammonium fluoroborate has been reported as an effective SDA, coupled with cobalt salt and 2-methylimidazole, to synthesize zeolitic imidazolate framework-67 (ZIF-67) derivatives for charge storage. However, the synthetic environment for growing cobalt-based active materials is relatively complex. In this study, cobalt tetrafluoroborate (Co(BF4)2) is proposed as a novel cobalt precursor, supplementing cobalt ions and acting as the SDA in a single chemical, to synthesize the cobalt-based electroactive material of energy storage electrodes. Interactions between solvent molecules and solutes play significant roles on the morphology, composition, and electrochemical performance of active materials. Deionized water, methanol and ethanol are used as precursor solvents to understand their effects on material and electrochemical properties. The optimal electrode presents a specific capacitance of 608.3 F/g at 20 mV/s, attributed to the highest electrochemical surface area and evident compositions of cobalt fluoride and hydroxide. A battery supercapacitor hybrid achieves the maximum energy density of 45 Wh/kg at 429 W/kg. The CF retention of 100% and Coulombic efficiency of 99% are achieved after 10,000 cycles.
RESUMEN
In this work, we demonstrated the synthesis of anions (X = selenium (Se), sulfur (S), and phosphorus (P)) doped cobalt oxytelluride (X-CoOTe) with oxygen and tellurium dual vacancies using hydrothermal methods, followed by selenization, sulfurization, and phosphorization reactions. Especially, the Se-CoOTe-modified nickel foam (Se-CoOTe/NF) electrode delivered a higher specific capacity (752.95 C/g) and an extremely lower charge transfer resistance (0.87 Ω) than S-CoOTe/NF and P-CoOTe/NF due to the higher metallic conductivity of Se. Both oxygen and tellurium vacancies facilitate higher charge transfer conductivity, specific capacity, and stability. On the other hand, banana stem core fiber-derived activated carbon fiber (AC) with exfoliated carbon sheet, cracked surface, and corresponding high surface area boosts the excellent cycle stability up to 4000 cycles with capacitance retention of 100.29%. Thus, the asymmetric device (Se-CoOTe/NF//AC/NF) exhibited an extendable cell voltage (1.55 V), higher energy density (155.6 W h kg-1) at a power density (1356.2 W kg-1), and generous long-term stability (100% retention up to 10 000 cycles) in a liquid alkaline electrolyte. In the practicability test, the proposed asymmetric device mutually showed an increased operating voltage from 1.55 to 4.65 V for a three-series connection. In a three-series connection, a single white LED and an LED string glowed efficiently. This new finding will be very useful to develop tellurium-based chalcogenides and biowaste-derived carbon for energy storage applications.
RESUMEN
In this study, a trimetallic selenide material with a hollow spherical structure (Co9Se8-CuSe2-WSe2) was synthesized through two consecutive solvothermal reactions. The synergistic effect between the quaternary elements, the benefits of the selenization of metals, and the unique morphology led to the prominent electrocatalytic ability of Co9Se8-CuSe2-WSe2 hollow spheres. Co9Se8-CuSe2-WSe2 hollow spheres were then mixed with oxygen plasma-treated multiwalled carbon nanotubes (MWCNT) as counter electrode (CE) material for dye-sensitized solar cells (DSSCs), achieving a photoelectric conversion efficiency (η) of 9.23% under one sun condition (AM 1.5G, 100 mW cm-2), surpassing the 8.08% of devices with platinum counter electrodes (PtCEs). For indoor conditions, a T5 light source was applied to the DSSCs with Co9Se8-CuSe2-WSe2 + MWCNT CE, and the efficiency increased to 14.14% under 3600 lx irradiance. Finally, Co9Se8-CuSe2-WSe2 + MWCNT CE demonstrated good stability with 92.23% retention after 1000 cycles of cyclic voltammetry, exceeding the 82.49% of PtCE. Therefore, Co9Se8-CuSe2-WSe2 + MWCNT shows potential as a substitute for platinum as CE material for DSSCs.
RESUMEN
For years, solution-type electrochromic devices (ECDs) have intrigued researchers' interest and eventually rendered themselves into commercialization. Regrettably, challenges such as electrolyte leakage, high flammability, and complicated edge-encapsulation processes limit their practical utilization, hence necessitating an efficient alternate. In this quest, although the concept of solid/gel-polymer electrolyte (SPE/GPE)-based ECDs settled some issues of solution-type ECDs, an array of problems like high operating voltage, sluggish response time, and poor cycling stability have paralyzed their commercial applicability. Herein, we demonstrate a choreographed-CeO2-nanofiller-doped GPE-based ECD outperforming its solution-type counterpart in all merits. The filler-incorporated polymer electrolyte assembly was meticulously weaved through the electrospinning method, and the resultant host was employed for immobilizing electrochromic viologen species. The filler engineering benefits conceived through the tuned shape of CeO2 nanorod and quantum dots, along with the excellent redox shuttling effect of Ce3+/Ce4+, synchronously yielded an outstanding class of GPE, which upon utilization in ECDs delivered impressive electrochromic properties. A combination of features possessed by a particular device (QD-NR/PVDF-HFP/IL/BzV-Fc ECD) such as exceptionally low driving voltage (0.9 V), high transmittance change (ΔT, â¼69%), fast response time (â¼1.8 s), high coloration efficiency (â¼339 cm2/C), and remarkable cycling stability (â¼90% ΔT-retention after 25,000 cycles) showcased a striking potential in the yet-to-realize market of GPE-based ECDs. This study unveils the untapped potential of choreographed nanofillers that can promisingly drive GPE-based ECDs to the doorstep of commercialization.